共查询到20条相似文献，搜索用时 15 毫秒
1.
Won Pyo Hong 《Marine Georesources & Geotechnology》2017,35(5):719-729
Lateral flow of soft ground occurs when embankment filling is performed on reclaimed land of foreshore. If a utility pipe is buried in soft ground undergoing the lateral flow, severe damage to the pipe can be caused. A pile-supported embankment has been used to support embankment to minimize lateral flow of the soft soil by transferring the embankment loads through the piles to the firm layer. To prevent damage to the buried pipe subjected to lateral force of the soft ground, full-scale field experiments on the piled embankment were conducted for 70 days. The test results show that the piled embankment effectively reduces both the settlements of the ground and the lateral displacements of the buried pipe. Although additional load was not imposed on the embankment after finishing embankment filling, the settlement and lateral displacement of soft ground simultaneously increased. This coupling behavior was observed at the toe of the embankment and the back of the buried pipe. To quantitatively evaluate the coupling effect of the movement, the coupling area (CA) was coined and analyzed with the efficiency of load transfer. The efficiency evaluated by the CA was in good agreement with the efficiency by the soil arching mechanism. 相似文献
2.
The effectiveness of constructing a geogrid-reinforced and pile supported embankment on soft ground to reduce differential settlement has been studied by pilot scale field tests and numerical analysis. Three-by-three pile groups with varying pile spacing were driven into a layer of soft ground, and a layer of geogrid was used as reinforcement over each pile group. Further, a 2-D numerical analysis has been conducted using the computer program FLAC 2D. The mechanisms of load transfer can be considered as a combination of embankment soil arching, geogrid tension, and stress transfer due to the difference in stiffness between pile and soft ground. Based on the pilot scale field tests and results of numerical analysis, we find that the geosynthetic reinforcement slightly interferes with soil arching, and helps reduce differential settlement of the soft ground. Also, the most effective load transfer and vertical stress reduction at the midspan between piles occurs when the pile cap spacing index D/b (D: pile cap spacing, b: diameter of pile) is 3.0. 相似文献
3.
Young-Suk Song 《Marine Georesources & Geotechnology》2013,31(1):34-52
The effectiveness of a simple method to estimate the lateral movement of piled bridge abutments due to lateral flow from the safety factor (Fs) of slope stability analysis was studied. This was accomplished through the construction and measurement of actual piled bridge abutments and its backfill, with and without piled slabs as a countermeasure. To do this, a computer program SLOPILE (VER 3.0) considering the lateral earth pressure acting on a row of piled bridge abutment was developed. SLOPILE (VER 3.0) can calculate the slope stability for both planar failure surfaces in infinite slopes and arc failure surfaces based on Fellenius or Bishop simplified methods. SLOPILE (VER 3.0) was utilized to design the piled bridge abutment reinforced by a piled slab at a real site. The piled slab can effectively prevent the lateral flow of soft ground and satisfy not only the safety factor of a slope but also the allowable bearing capacity of piles. To verify the design method, an instrumentation system was adapted. The instrumentation results from a case study clearly showed that the piled slab effectively resisted the lateral movement of a bridge abutment due to placement of backfill. Also, the surcharge loads due to backfill were supported by the piled slab and transmitted to the bedrock through the piled slab. 相似文献
4.
AbstractThis study investigates the impact of pile cap size, soft layer thickness and pile strength on load transfer and settlement behaviors of embankments supported by floating and fixed T-shaped deep cement mixing piles and conventional DCM piles under volume control. Preliminary investigation is performed by a series of small-scale physical model tests. The results reveal that the differential settlement can be substantially reduced with an enlarging pile cap as a result of larger embankment load transferred to the piles. The extended numerical analysis results demonstrate that the pile efficacy is related to the individual pile bearing capacity, which, in turn, depends on the pile cap size. The soft layer thickness has an insignificant effect on differential settlement but a significant effect on average settlement, while the pile strength plays an important role in differential settlement only when the cap size is not very large. Shape factor of at least 3.0 is recommended to ensure the reduction in differential settlement and minimize the effect of the change in pile strength. 相似文献
5.
6.
AbstractMono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay. 相似文献
7.
AbstractIn this article, the degradation of the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading is studied numerically. A modified kinematic hardening constitutive model is employed to simulate the degradation of soft clay after cyclic loading. The modified model is verified by comparing the numerical simulation results with the results of centrifuge model tests. Furthermore, the modified model is applied to numerical simulations for evaluating the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading. The degradation of the lateral bearing capacity of piles in soft clay after different cyclic displacement levels and different numbers of cycles is investigated. The study reveals that the modified kinematic hardening constitutive model can effectively estimate the cyclic degradation behavior of piles in soft clay subjected to cyclic lateral loading. The degradation of the ultimate lateral bearing capacity progresses slowly with increasing cyclic displacement level for fewer cycles, and the degradation develops significantly at higher levels of cyclic displacement after applying a larger number of cycles. 相似文献
8.
Reinforcement and Arching Effect of Geogrid-Reinforced and Pile-Supported Embankment on Marine Soft Ground 总被引：1，自引：0，他引：1
The effectiveness of constructing a geogrid-reinforced and pile supported embankment on soft ground to reduce differential settlement has been studied by pilot scale field tests and numerical analysis. Three-by-three pile groups with varying pile spacing were driven into a layer of soft ground, and a layer of geogrid was used as reinforcement over each pile group. Further, a 2-D numerical analysis has been conducted using the computer program FLAC 2D. The mechanisms of load transfer can be considered as a combination of embankment soil arching, geogrid tension, and stress transfer due to the difference in stiffness between pile and soft ground. Based on the pilot scale field tests and results of numerical analysis, we find that the geosynthetic reinforcement slightly interferes with soil arching, and helps reduce differential settlement of the soft ground. Also, the most effective load transfer and vertical stress reduction at the midspan between piles occurs when the pile cap spacing index D/b (D: pile cap spacing, b: diameter of pile) is 3.0. 相似文献
9.
AbstractWith the large-scale development and utilization of ocean resources and space, it is inevitable to encounter existing submarine facilities in pile driving areas, which necessitates a safety assessment. In this article, by referring to a wharf renovation project as a reference, the surrounding soil response and buried pipe deformation during pile driving in a near-shore submarine environment are investigated by three-dimensional (3D) numerical models that consider the pore water effect. Numerical studies are carried out in two different series: one is a case of a single pile focusing on the effect of the minimum plane distance of the pile–pipe, and the other is a case of double piles focusing on the effect of the pile spacing. 相似文献
10.
ABSTRACTThe strain wedge model effectively performs nonlinear analyses of the lateral response of piles by using a nonlinear stress-strain relationship to describe soil behavior in the strain wedge. In this study, a state-dependent plasticity model has been implemented in the strain wedge model to calculate the stress-strain relationship for sand in the strain wedge. To complement this implementation, the effect of dilatancy on the shear strain is considered in the strain wedge. A full-scale test and a 45 g centrifuge model test on laterally loaded piles are used to validate the proposed method. The results show that the deflections and moments predicted by the proposed method accord well with those measured from full-scale and centrifugal model pile tests. Moreover, the combination of the state-dependent plasticity model and the strain wedge model allows for analyzing the lateral response of single piles using a unique set of model parameters for different relative densities of sands. In addtion, the stress-strain response in the strain wedge, not the dilatancy, dominates the soil resistance in the strain wedge and thus the lateral response of piles. 相似文献
11.
AbstractAn experimental study of the performance of concrete pipe piles during installation under different penetration speeds and static load tests on the piles in sand is presented. The applied jacking force, the amount of pile penetration, length of soil plug formed and ultimate bearing capacity were measured during the model tests. The results showed that the concrete pipe piles were partially plugged and the behavior of the soil plug was significantly affected by the penetration speed. The lower the penetration speed, the larger the soil plug formed which in turn leads to a greater ultimate bearing capacity. The size of soil plug can be evaluated by the m value defined as the ratio of the volume of the soil plug to that of the penetrated pile wall. The relationship between the m value and the penetration speeds can be used to estimate the amount of soil plug and the depth of penetration for an open-ended concrete pipe pile jacked into sand. 相似文献
12.
Jun Wang Zhi Zhou Hongtao Fu Yuanqiang Cai Xiuqing Hu 《Marine Georesources & Geotechnology》2013,31(7):870-879
AbstractLand reclamation has increased significantly in the eastern coastal areas of China. The increased exploitation of offshore resources has made cast-in-situ piles more preferable in these regions. However, precise prediction of axial forces and shaft resistances of piles is particularly difficult because geological conditions are complex after the foundation is treated by vacuum preloading. In this study, two groups of cast-in-situ piles, each of which consisted of two piles installed in soft soil in Oufei Project, Wenzhou, China, were compared by conducting tests using the slow static loading method to evaluate the influence of applying vacuum preloading to deal with soft soil foundation on the vertical bearing capacities of the piles. Two piles were located in an untreated area, while the other two were located in a vacuum preloading treating area. All the piles had the same length and diameter. In addition, the axial forces and shaft resistances of piles were calculated based on the measured strains. The field tests revealed that the ultimate bearing capacities and shaft resistances of test piles were significantly improved compared to those of the piles in untreated area. The experimental results presented in this study are expected to be highly beneficial for practical engineering. 相似文献
13.
The self-supported earth-retaining structure using stabilizing piles (SSR is used from here) has the advantages of less deformation and less internal force compared with conventional cantilever retaining structure. It is easier to conduct the excavation when SSR is used for an excavation instead of using braced excavation with struts. The SSR is better than other methods to the 10 m shallow excavation depth in terms of economical and constructional efficiency when the ground is not very soft. However, this SSR method lacks a theoretical basis in terms of geotechnical engineering. The objective of this study is to develop a method of analysis by laboratory model tests. A variety of model tests were performed in order to analyze the behavior of SSR and the ground, and to measure the stress acting on stabilizing piles relative to excavation steps and earth pressures on the wall. The analysis reveals the failure mechanism of a wedge and then suggests a method for calculating a virtual supported point. These findings were incorporated into a method for analyzing retaining wall, stabilizing piles, and beams connecting two structures. Future research is geared toward developing a design program that uses the analytical methodology for this SSR. 相似文献
14.
一种新型筑堤结构：轻质硬壳堤坝 总被引：10，自引：1，他引：9
针对软弱地基存在的堤坝不均匀沉降、滑坡、位移、倒塌等问题,提出了一种新型的筑堤结构──轻质硬壳堤坝。该结构采用发泡塑料作为堤坝材料,或铺设于软基面上,或填充于易沉陷部位,或搅拌于土石方中;以高强度材料,制成堤坝外壳或堤坝某一部分的外壳,然后填入其他松散材料,使其产生减重、加筋、防渗、隔离、堆高的作用,以增强堤坝刚度,提高堤坝稳定性。这种新型堤坝结构具有较高的防洪、抗地震能力,以及缩短建筑工期,降低造价,废物利用等优点。 相似文献
15.
Effects of a cover layer on wave-induced pore pressure around a buried pipe in an anisotropic seabed 总被引：1，自引：0，他引：1
In engineering practice, a cover layer of coarser material has been used to protect a buried marine pipeline from wave-induced seabed instability. However, most previous investigations of the wave–seabed–pipe interaction problem have been concerned only with such a problem either in an isotropic single layer or a rigid pipe. This paper proposes a two-dimensional finite element model by employing the principle of repeatability to investigate the wave-induced soil response around a buried pipeline. The elastic anisotropic soil bahavior and geometry of cover layer are included in the present model, while the pipe is considered to be an elastic medium. This study focuses on the effects of a cover layer (including thickness B and width W of the cover layer) on the wave-induced pore pressure in the vicinity of a buried pipeline. 相似文献
16.
Peiwu Shen Dingjian Wang Yibing Ning Yongquan Zhang Xuexue Su 《Marine Georesources & Geotechnology》2020,38(7):818-829
AbstractFluctuant marine and reservoir water levels are the main failure-inducing factors for embankment slopes. The soft embankment rocks, e.g., red-bed mudstone, eroded by the reservoir water level in the Three Gorges Reservoir area greatly influence the stability of the embankment slopes. In this study, unified strength theory was innovatively applied for damage evaluation and combined with the Weibull distribution to obtain the strength statistics of micro units. Additionally, one damage constitutive model and one damage evolution model considering the initial damage, strain softening and damage weakening were proposed. Then, a series of tests, e.g., modified cyclic wetting and drying test, triaxial compression test and modified numerical simulation test for reservoir embankment red-bed mudstone, were conducted to verify the feasibility of the proposed models. In addition, grey system theory was originally used to evaluate the effects of the Weibull distribution parameters (m and w) and the confining stress on the peak stress. Finally, the proposed model was tentatively applied to the modification of the limit failure height model of the bedded rock slopes. The verification implies that the proposed model results are consistent with the testing results, especially in the simulation of compaction, elastic deformation and strain softening and in the prediction of peak strength. The results from grey system theory analysis indicate that the micro unit strength parameter (w) has the most obvious effect on the strength. Moreover, the modified method based on the damage evolution model for calculating the limit failure height of the bedded rock slopes is conservative. 相似文献
17.
Deep cement mixing (DCM) technique is a deep in-situ stabilization technique by mixing cement powder or slurry with soft soils below the ground surface to improve their properties and behavior. Some of DCM treated soft soil grounds are approximately in a plane-strain condition; for example, a fill embankment on DCM improved ground. In this study, a plane-strain physical model was created with instrumentation and used to investigate the bearing capacity and failure mode of a soft soil improved by an end-bearing DCM column group. This study focuses on the observed wedge-shaped shear failure of the model ground and attempts to give an account of the failure. Two different methods are used to calculate the bearing capacity of the model ground, and the computed values are compared with the measured ones. It is found that the simple Brom's method gives a better estimate of the bearing capacity of the present model ground. It is also found that measured data of pore water pressures at different locations in the soft soil indicate coupling between failure of columns and consolidation of the soft soil. This study has presented the first time that a wedge-shaped block failure was observed for pattern of DCM treated soil ground. 相似文献
18.
19.
Yun Wook Choo Ji-hoon Seo Young-Nam Kim Jeong-min Goo Young-ho Kim 《Marine Georesources & Geotechnology》2016,34(8):729-740
This study aims to investigate a hybrid gravity base foundation to support offshore wind tower. A new hybrid gravity base foundation considered in this study has five component piles, referred to as ‘piled gravity base foundation’. The three-dimensional finite element analyses were carried out for the piled gravity base foundation subjected to a combined load with a lateral load and overturning moment. The parametric analyses were undertaken varying the loading height and direction, the rigidity of the piled gravity base foundation, the field soil layers, and the clay strength. Overall, the response of the piled gravity base foundation was significantly influenced by the interaction between the cone base piles and the surrounding soil. The increased strength of the soil led to a significant reduction of the pile and gravity base foundation responses, in terms of the bending moments, axial forces, lateral displacements, and rotations. 相似文献
20.
An angle exists between the initial static shear stress and cyclic shear stress when embankment and retaining walls are subjected to cyclic loadings. To investigate the influence of this angle on the dynamic properties of marine soft clay, tests were performed on Wenzhou soft clay. When the angle was varied from 0° to 90°, the shear strain and excess pore pressure decreased as θ increased while increased as θ increased from 120° to 180°. Shear strain developed more rapidly when θ was 120°, 150°, or 180° than that when θ was 0°, 30°, or 60°. These results indicate that the number of cycles to failure at the larger angles was greater than at the smaller angles. When θ was 90°, the strain in the x-axis direction increased as the number of cycles increased. The development of the excess pore pressure associated with specimen failure was different for different cyclic shear stress ratios and shearing angles. The effect of θ on the strain and excess pore pressure increased as the cyclic shear stress ratio increased. 相似文献