共查询到20条相似文献，搜索用时 31 毫秒
1.
AbstractAn experimental study of the performance of concrete pipe piles during installation under different penetration speeds and static load tests on the piles in sand is presented. The applied jacking force, the amount of pile penetration, length of soil plug formed and ultimate bearing capacity were measured during the model tests. The results showed that the concrete pipe piles were partially plugged and the behavior of the soil plug was significantly affected by the penetration speed. The lower the penetration speed, the larger the soil plug formed which in turn leads to a greater ultimate bearing capacity. The size of soil plug can be evaluated by the m value defined as the ratio of the volume of the soil plug to that of the penetrated pile wall. The relationship between the m value and the penetration speeds can be used to estimate the amount of soil plug and the depth of penetration for an open-ended concrete pipe pile jacked into sand. 相似文献
2.
大直径超长桩的可打入分析是海洋平台打桩施工顺利进行的重要保障,土塞是否闭合的判断对于桩基可打入性分析具有较大的影响,因此,合理准确的土塞判断结果对提高桩的可打入分析的准确性具有重要的意义。以现场静力触探(CPTU)试验数据为依据,采用孔扩张理论推导了基于CPTU测试结果的桩端土的极限承载力计算公式;在求解桩端土体承载力时考虑了管桩与土体的刚度差异,同时考虑到打桩过程中的土体扰动。采用Randolph推荐的方法得到了土塞阻力,将两者进行比较,进而判断土塞的状态。通过实际工程的实测数据,对各个土层的土塞状况进行了判别,并根据判别情况采用波动方程的方法对桩基的可打入性进行了分析,将预测结果和现场的打桩记录进行了比较。计算结果显示,提出的方法与实测结果更为接近,有效地提高了桩的可打入性的预测精度。 相似文献
3.
Calibration chamber tests were conducted on open‐ended model piles driven into dried siliceous sands with different soil conditions in order to clarify the effect of soil conditions on load transfer mechanism in the soil plug. The model pile used in the test series was devised so that the bearing capacity of an open‐ended pile could be measured as three components: outside shaft resistance, plug resistance, and tip resistance. Under the assumption that the unit shaft resistance due to pile‐soil plug interaction varies linearly near the pile tip, the plug resistance was estimated. The plug capacity, which was defined as the plug resistance at ultimate condition, is mainly dependent on the ambient lateral pressure and relative density. The length of wedged plug that transfers the load decreases with the decrease of relative density, but it is independent of the ambient pressure and penetration depth. Under several assumptions, the value of earth pressure coefficient in the soil plug can be calculated. It gradually reduces with increase in the longitudinal distance from the pile tip. At the bottom of the soil plug, it tends to decrease with increase in the penetration depth and relative density, and to increase with the increase of ambient pressure. This may be attributed to (1) the decrease of friction angle as a result of increase in the effective vertical stress, (2) the difference in the dilation degree of the soil plug during driving with ambient pressures, and (3) the difference in compaction degree of soil plug during driving with relative densities. Based on the test results, an empirical equation was suggested to compute the earth pressure coefficient to be used in the calculation of plug capacity using one‐dimensional analysis, and it produces proper plug capacities for all soil conditions. 相似文献
4.
Foundation piles of the offshore oil platforms in the Bohai Bay are usually longer than 100 m with a diameter larger than 2 m.Driving such long and large-sized piles into the ground is a difficult task.It needs a comprehensive consider ation of the pile dimensions,soil properties and the hammer energy.Thoughtful drivability analysis has to be performed in the design stage.It has been shown that judging whether the soil column inside the pile is fully plugged,which makes the pile behave as close-ended,strongly influences the accuracy of drivability analysis.Engineering practice repeatedly indicates that the current methods widely used for soil plug judgment often give incorrect results,leading the designers to make a wrong decision.It has been found that this problem is caused by the ignorance of the bearing capacity provided by the soil surrounding the pile.Based on the Terzaghi’s bearing capacity calculation method for deep foundation,a new approach for judging soil plug status is put forward,in which the surcharge effect has been considered and the dynamic effect coefficient is included.This approach has been applied to some practical engineering projects successfully,which may give more reasonable results than the currently used method does. 相似文献
5.
Giovanni Spagnoli Cristina de Hollanda Cavalcanti Tsuha 《Marine Georesources & Geotechnology》2020,38(9):1013-1036
AbstractHelical piles are used mainly to resist tension forces generated by uplift and overturning moments of various structures, therefore they have been suggested as a potential alternative to driven piles as offshore pile because they provide a large uplift capacity due to the anchor effect of the helix. To date no standards are available for the assessment of the use of helical piles in the offshore environment. State-of-the art installation and uplift capacity assessment is based on field onshore tests on small helical piles. The purpose of this review is to critically evaluate the current knowledge on helical piles considering uplift capacity, cyclic load, installation torque models and the parameters affecting the installation torque, to understand whether they can be considered for potential offshore applications. The paper could be of valuable interest for engineers and contractors involved in the offshore installation of piles. 相似文献
6.
Abstract This article discusses a possible alternate foundation system for a tension leg platform (TLP) in deep water. It was developed through Tecnomare S.p.A. for Agip S.p.A. during a feasibility study of a site located in the southern Adriatic Sea having a water depth of 827 m. The system is a combination of a pile‐gravity foundation, with relatively short (?20 m) steel piles of very large diameter (6 to 12 m) called “superpiles,”; which are closed at the top and open at the bottom. The superpiles are installed in soft soil under the effect of self‐weight and active suction. Permanent tension of the TLP tendons is equilibrated by self‐weight only; tension due to wave action is equilibrated by the weight of the soil inside the superpiles. In fact, a pulsating tension applied to the superpiles generates a suction in the pore water that tends to keep the soil plug inside the cylinder and prevents the cylinder as a whole from being extracted from the (impervious) foundation soil. The results of analyses of the installation and in service behavior of superpiles are described on conventional principles of soil mechanics and related to a typical profile at the Adriatic site. Installation problems are briefly discussed; then the stability in service is examined to evaluate the capacity of superpiles in compression and tension and the associated factors of safety. Finally, considering the pore pressure gradient generated by the applied tension inside the soil plug, the flow rate and related deformations during storms and during the entire expected life of the TLP are evaluated. The proposed superpile system appears to be feasible, simple to install, and economical. Further study and experimental research are justified to optimize the system. 相似文献
7.
AbstractPile foundation is the most popular option for the foundation of offshore wind turbines. The degradation of stiffness and bearing capacity of pile foundation induced by cyclic loading will be harmful for structure safety. In this article, a modified undrained elastic–plastic model considering the cyclic degradation of clay soil is proposed, and a simplified calculation method (SCM) based on shear displacement method is presented to calculate the axial degradated capacity of a single pile foundation for offshore wind turbines resisting cyclic loadings. The conception of plastic zone thickness Rp is introduced to obtain the function between accumulated plastic strain and displacement of soil around pile side. The axial ultimate capacity of single piles under axial cyclic loading calculated by this simplified analysis have a good consistency with the results from the finite element analysis, which verifies the accuracy and reliability of this method. As an instance, the behavior of pile foundation of an offshore wind farm under cyclic load is studied using the proposed numerical method and SCM. This simplified method may provide valuable reference for engineering design. 相似文献
8.
AbstractIn this article, the drivability of stepped and tapered offshore piles with the same length and volume has been investigated under hammer blows. To justify the obtained results from field testing and numerical methods, this pile driving procedure has been analyzed and discussed with wave propagation mechanism. It will be shown that tapered pile can be confidently idealized as a number of prismatic segments connected rigidly to each other. This is an interesting finding that fully tapered or stepped piles have a better performance in pile driving and enable users to apply simple one dimensional numerical analysis for simulating pile drivability. 相似文献
9.
AbstractThis study established a Couple Eulerian–Lagrange model to simulate monopile vibratory penetration for the investigation of soil plugging effect during high-frequency penetration of monopiles for wind turbine. Simulation analysis is focused particularly on soil plugging effect of a large diameter monopile during vibratory penetration into sand, clay, or layered soil. The results of the numerical simulation show that soil plugging effect is unlikely to occur during monopile penetration into the clay soil, while partial soil plugging may occur during the sand penetration. Penetration resistance at the pile toe is transferred to the radial stress around the pile wall. At a critical point penetration process, internal shaft friction becomes larger than external shaft friction. Moreover, radial pressure factors increase during partial soil plugging effect. For layered soil, the topsoil not only has great influence on the soil plugging effect, but also affects shaft friction in the subsoil during monopile penetration. 相似文献
10.
Giovanni Spagnoli Cristina de Hollanda Cavalcanti Tsuha 《Marine Georesources & Geotechnology》2020,38(9):1118-1120
AbstractA closure on the recent discussion regarding the review on the behavior of helical piles as a potential offshore foundation system by the Authors is presented. Installation torque, uplift capacity, installation effects, model pile, installation speed and results proposed by Discussers are commented. 相似文献
11.
C. Y. Lee 《Marine Georesources & Geotechnology》2013,31(4):279-297
Abstract A nonlinear pile‐soil interface model incorporated in a boundary element analysis is presented to simulate both the static and cyclic behavior of piles embedded in cemented and noncemented calcareous sediments. Based on the soil parameters derived from model test data, theoretical predictions are made for a few field tests. Finally, theoretical solutions are obtained for a full‐scale hypothetical pile embedded in homogeneous and layered calcareous sediments. 相似文献
12.
AbstractIn onshore and offshore fields of ocean engineering, piles are used as foundation systems for various structures. Piles are classified into different types depending on their materials, geometries, and particularly, installation methods, which have advantages or limitations. Companies and engineers have developed a new group of piles, because of necessity to improve their performance in terms of increasing the bearing capacity, reducing impacts of traditional installation procedures, implementing by low- torque power equipment, and utilizing them in widely different ground conditions, including in a marine environment. In the present study, three different models of a new pile with an expander body are introduced to increase the shaft and pile-toe diameters and its self-expansion in the embedment depth under the titles of the Bubble pile (BP), Self-Expanded pile (SEP) and Wing pile (WP). The main subject of this research is to achieve increased bearing capacity, reduced installation effects, and decreased required installation torque. The frustum-confining vessel of Amirkabir University of Technology (FCV-AUT) was employed for this purpose. Up to 14 axial compressive and tensile load tests were carried out on different model piles on sand collected from Anzali shore located on the northern coast of Caspian Sea in Iran, with relative densities of 45% to 50% within FCV-AUT. Comparing the performance of introduced pile with traditional pile corresponding to the same characteristics, the results indicated a significant increase in the axial bearing capacity and reduced disturbance effect of the pile. Also, a lower installation torque of the SE pile was required compared to the helical pile. The test results also demonstrated that the new pile could resist considerable compressive and uplift loads, and could be a possible alternative to traditional piles in the onshore sector. 相似文献
13.
大直径钢管桩土塞效应的判断和沉桩过程分析 总被引：5，自引：0，他引：5
港口工程和海洋工程中出现了越来越多的大直径超长钢管桩。由于这种桩直径较大,土塞的形成对桩的可打入性和承载力有较大的影响。鉴于此,根据大直径和超大直径钢管桩土塞性状的特殊性,考虑了桩直径对侧壁摩阻力、端阻力的影响,引入了尺寸效应系数,重新建立了土塞微分体的静力平衡方程,提出了采用改进的静力平衡法进行土塞效应判断,同时采用波动方程法近似模拟土塞与桩管内壁的相互作用,建立了简化的土塞与桩壁相互作用模型,并用该方法进行实际工程的打桩分析,分析结果表明该方法对土塞效应的判断、打桩过程的预测等与工程实测数据吻合较好。 相似文献
14.
Amirhossein Mohammadi Abolfazl Eslami Sjoerd E. A. T. M. van der Zee 《Marine Georesources & Geotechnology》2013,31(2):164-179
ABSTRACTOil and its derivatives contaminate many soils and not only affect their chemical and biological properties but also their geotechnical properties. As oil contamination may deteriorate the functioning of piles, this paper addresses the effects of oil contamination on soil–pile interactions. Axial compressive bearing capacities of two close-ended, instrumented piles were investigated in different oil-contaminated sand using frustum confining vessel. Three different oils (gasoil, crude oil, and used motor oil) at different contamination levels were considered and using some strain gauges, the toe, shaft, and the net total bearing capacity of piles, as well as load distributions along the pile length, were derived. The results show that the presence of oil between soil particles has considerable adverse effects on bearing capacities of model piles, especially the shaft bearing capacity. The oil viscosity and percentage, as well as the contaminated sand bed thickness around the piles, are the most influential parameters. The higher the oil viscosity and oil content, the lower the values of the piles’ bearing capacities in comparison to the uncontaminated sand. With some modifications on the bearing capacity parameters of CFEM method, a good agreement was observed between measured and calculated bearing capacity values. 相似文献
15.
AbstractMono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay. 相似文献
16.
AbstractIn practice, how to quickly improve the bearing capacity of piles in a short time is of great significance. In view of this, a technique of setting grooves and installing PVDs (prefabricated vertical drains) at the surface of the pile is proposed in this investigation to accelerate the consolidation of the surrounding soil. A radial and circular consolidation model is established for permeable piles. The finite cosine transform, finite Weber transform, and discretization method are used to obtain a semi-analytical solution for the consolidation model with a mixed drainage boundary condition at the surface of the pile. The sensitivity of the consolidation process to the strip number and the width of PVDs is discussed. The results show that the technique of installing PVDs in piles could potentially improve the bearing capacity. When the area of drainage channels is fixed, the bearing capacity of permeable piles can be more effectively improved by using a higher strip number of PVDs and a smaller PVD width. 相似文献
17.
AbstractWith the large-scale development and utilization of ocean resources and space, it is inevitable to encounter existing submarine facilities in pile driving areas, which necessitates a safety assessment. In this article, by referring to a wharf renovation project as a reference, the surrounding soil response and buried pipe deformation during pile driving in a near-shore submarine environment are investigated by three-dimensional (3D) numerical models that consider the pore water effect. Numerical studies are carried out in two different series: one is a case of a single pile focusing on the effect of the minimum plane distance of the pile–pipe, and the other is a case of double piles focusing on the effect of the pile spacing. 相似文献
18.
AbstractThis study investigates the impact of pile cap size, soft layer thickness and pile strength on load transfer and settlement behaviors of embankments supported by floating and fixed T-shaped deep cement mixing piles and conventional DCM piles under volume control. Preliminary investigation is performed by a series of small-scale physical model tests. The results reveal that the differential settlement can be substantially reduced with an enlarging pile cap as a result of larger embankment load transferred to the piles. The extended numerical analysis results demonstrate that the pile efficacy is related to the individual pile bearing capacity, which, in turn, depends on the pile cap size. The soft layer thickness has an insignificant effect on differential settlement but a significant effect on average settlement, while the pile strength plays an important role in differential settlement only when the cap size is not very large. Shape factor of at least 3.0 is recommended to ensure the reduction in differential settlement and minimize the effect of the change in pile strength. 相似文献
19.
Zhou Jia-Jin Gong Xiao-Nan Zhang Ri-Hong Wang Kui-Hua Yan Tian-Long 《Marine Georesources & Geotechnology》2020,38(1):97-107
AbstractThis paper presents the results of a series of model tests performed to study the shaft capacity of pre-bored grouted planted nodular (PGPN) pile in dense sand. The influence of the vertical overburden pressure on the shaft capacity of the PGPN pile is also investigated based on the test results. The test piles were equipped with strain gauges to measure the axial loads during the loading process, moreover, a foam plate was buried beneath pile tip to eliminate the influence of tip resistance on the shaft capacity. Some conclusions can be drawn based on the test results: the peak skin friction of PGPN pile increases with the increase of vertical overburden pressure applied on the foundation soil, while the rate of increase decreases with the increasing overburden pressure; the surface of the pile–soil interface of PGPN pile is relatively rough, and significant dilatant increase in lateral stress occurs during the loading process. 相似文献
20.
Helical piles are structural deep foundation elements, which can be categorized as torque-driven piles without any limitations to implement in marine situations. Different methods are used to predict the axial capacity of helical piles, such as static analysis, but have some limitation for this type of piles on marine conditions. In situ testing methods as supplement of static analysis have been rarely used for helical piles. In geotechnical engineering practice, the most common in situ tests particularly applicable for coastal or offshore site investigation are cone penetration test (CPT) and piezocone penetration test (CPTu). The CPT is simple, repeatable, and prepares the continuous records of soil layers. In this paper, a data bank has been compiled by collecting the results of static pile load tests on thirty-seven helical piles in ten different sites including CPT or CPTu data. Axial capacities of thirty-seven helical piles in different sites were predicted by direct CPT methods and static analysis. Accuracy estimation of ten direct CPT methods to predict the axial capacity of helical piles was investigated in this study. Comparisons have been made among predicted values and measured capacity from the pile load tests. Results indicated that the recently developed methods such as NGI-05 (2005), ICP-05 (2005), and UWA-05 (2005) predicted axial capacity of helical piles more accurately than the other methods such as Meyerhof (1983), Schmertmann (1978), Dutch (1979), LCPC (1982), or Unicone (1997). However, more investigations are required to establish better correlation between CPT data and axial capacity of helical piles. 相似文献