共查询到20条相似文献，搜索用时 15 毫秒
1.
Accurate propeller shaft speed controllers can be designed by using nonlinear control theory and feedback from the axial water velocity in the propeller disc. In this paper, an output feedback controller is derived, reconstructing the axial flow velocity from vehicle speed measurements, using a three-state model of propeller shaft speed, forward (surge) speed of the vehicle, and the axial flow velocity. Lyapunov stability theory is used to prove that a nonlinear observer combined with an output feedback integral controller provide exponential stability. The output feedback controller compensates for variations in thrust due to time variations in advance speed. This is a major problem when applying conventional vehicle-propeller control systems. The proposed controller is simulated for an underwater vehicle equipped with a single propeller. The simulations demonstrate that the axial water velocity can be estimated with good accuracy. In addition, the output feedback integral controller shows superior performance and robustness compared to a conventional shaft speed controller 相似文献
2.
The existing propulsor that can perform both propulsion and maneuvering along axis of rotation is propeller/rotor for a helicopter. Helicopter propellers when maneuvering increase or decrease their blades’ pitch cyclically to create imbalanced thrust and hence maneuvering force/torque. A “maneuverable propeller” was developed and its performance on both maneuvering and propulsion is assessed. The “maneuverable propeller” is an alternative of the existing helicopter rotors. The novelty of this propulsor is that the imbalanced thrust force/torque is created by cyclically increasing or decreasing the angular speed of their blades relatively to the hubs/shafts, to provide the desired maneuvering torque. This maneuverable propeller is hence defined as the Cyclic Blade Variable Rotational Speed Propeller (CBVRP). One of the best advantages is that the maneuvering torque created by the “maneuverable propeller” is much higher, about 5 times of the shaft torque of the same propeller at thrust only mode. The “maneuverable propeller” has wide applications for both surface ships and underwater vehicles that require high maneuverability for cruising inside the narrow passage. 相似文献
3.
Healey A.J. Rock S.M. Cody S. Miles D. Brown J.P. 《Oceanic Engineering, IEEE Journal of》1995,20(4):354-361
This paper proposes a novel approach to modeling the four quadrant dynamic response of thrusters as used for the motion control of ROV and AUV underwater vehicles. The significance is that these vehicles are small in size and respond quickly to commands. Precision in motion control will require further understanding of thruster performance than is currently available. The model includes a four quadrant mapping of the propeller blades lift and drag forces and is coupled with motor and fluid system dynamics. A series of experiments is described for both long and short period triangular, as well as square wave inputs. The model is compared favorably with experimental data for a variety of differing conditions and predicts that force overshoots are observed under conditions of rapid command changes. Use of the model will improve the control of dynamic thrust on these vehicles 相似文献
4.
Improvements of estimation accuracy on propeller torque fluctuations in waves will contribute assessments on safe operation of a ship main engine as in adverse sea condition. The propeller torque and thrust in waves can be estimated by propeller effective inflow velocity in waves, using the propeller open-water characteristics. Fluctuation components in the mathematical model of the propeller effective inflow velocity in waves can be composed of two components, respectively caused by ship surge motion and wave orbital motion at propeller position. In this study, an experimental method by the model test to directly identify the characteristics of the component by the wave orbital motion is newly proposed. Furthermore, the free-running model test in regular waves, using a simulator of the marine diesel engine which manages the shaft speed of the motor on a ship model as behaving the actual diesel engine, is carried out to obtain realistic torque fluctuations for comparisons of the estimated results applying the proposed identification method. Through comparisons of estimated fluctuations with the measured results, the proposed approach for the component of the inflow velocity due to wave orbital motion is successfully validated. 相似文献
5.
As an extremely significant tool, autonomous underwater vehicles (AUVs) obtain corresponding development which is widely used in the oceanographic survey, military applications and ocean investigation. However, it is rather hard to fulfill missions about ocean exploration in suspended status or at slow speeds for traditional AUVs, due to the effect of the control surfaces trends to decline or even invalid completely in this condition. To overcome the limitation mentioned above, a torpedo-shaped AUV with vectored thrust ducted propeller is presented in this paper, in which the vector thruster is designed based on a 3SPS-S parallel manipulator. The 3SPS-S parallel manipulator, which has merits of compact structure, high reliability, high precision and fast response, is employed for thrust vectoring control mechanism. Additionally, the kinematics and dynamics model of the thrust-vectoring mechanism is constructed, and the MATLAB simulation results show the designed vectored thruster have great application superiority and potential for AUV. Finally, a control scheme of the vectored thruster is designed after considering the case study. The main idea of this paper lies in describing a novel design of the vectored thruster AUV based on 3SPS-S parallel manipulator, which can complete the mission at zero or slow forward speeds. 相似文献
6.
The tip vortex cavitation (TVC) is an issue of increasing interest, because the TVC plays an important role in propeller radiated noise and cavitation erosion. The marine propeller with winglets, which is inspired by the winglets of airfoil, is numerically investigated in the present paper. The blade tip of newly designed propeller tilts toward the pressure side. The difference between six propellers is the change of the rake angle at r/R = 1.0. The pressure coefficient, TVC, axial velocity field and helicity are analyzed. The numerical results show that the winglets of newly designed propeller scarcely affect the efficiency of propeller. The thrust coefficient gradually decreases with the increase in rake angle. As for the suction side, the pressure coefficient (Cp) of winglets propellers is higher than the conventional propeller in general. In addition, the winglets are beneficial to generate less cavitation behavior when the rake angle is small. However, as the rake angle is further increased, the cavitation behavior of winglets propeller is also increased, even larger than the conventional propeller. Therefore, it can be deduced that the winglets can be used to effectively improve the TVC characteristics to some extent. 相似文献
7.
The present paper describes results of the experimental investigation of a small-scale mono-hull model boat propelled by a localised flexural wave propagating along the plate of finite width forming the boat's keel. Forward propulsion of the boat was achieved through flexural wave propagation in the opposite direction, which is similar to the aquatic propulsion used in nature by stingrays. The model boat under consideration underwent a series of tests both in a Perspex water tank and in an experimental pool. In particular, the forward velocity of the boat has been measured for different frequencies and amplitudes of the flexural wave. The highest velocity achieved was 32 cm/s. The thrust and propulsive efficiency have been measured as well. The obtained value of the propulsive efficiency in the optimum regime was 51%. This indicates that the efficiency of this type of aquatic propulsion is comparable to that of dolphins and sharks (around 75%) and to that of a traditional propeller (around 70%). In contrast with a propeller though, the wave-like aquatic propulsion has the following advantages: it does not generate underwater noise and it is safe for people and marine animals. 相似文献
8.
Numerical simulation and experimental research on hydrodynamic performance of propeller with varying shaft depths 总被引：2，自引：0，他引：2
In order to study hydrodynamic performance of a propeller in the free surface, the numerical simulation and open-water experiments are carried out with varying shaft depths of propeller. The influences of shaft depths of a propeller on thrust and torque coefficient in calm water are mainly studied. Meanwhile, this paper also studies the propeller air-ingestion under special working conditions by experiment and theoretical calculation method, and compares the calculation results and experimental results. The results prove that the theoretical calculation model used in this paper can imitate the propeller air-ingestion successfully. The successful phenomenon simulation provides an essential theoretical basis to understand the physical essence of the propeller air-ingestion. 相似文献
9.
螺旋桨工作时在其周围形成诱导速度场,诱导速度随到桨叶距离的增大而衰减。采用CFD方法模拟螺旋桨敞水性能时,只能截取有限尺度的流域进行计算,此时计算域边界上诱导速度并不为零,将进口速度设为进速是近似的。一般采用足够大的计算域,使螺旋桨前方及侧面边界尽量远离桨叶。为了在较小的计算域中实现螺旋桨敞水性能的准确预报,提出在设定进口速度时计入螺旋桨诱导速度的CFD模拟方法。应用升力面方法计算诱导速度,将进口速度设为进速与诱导速度之和。逐步减小计算域尺度,考察敞水性能及压力分布计算结果的变化情况及精度。算例比较表明:通过考虑诱导速度,可以大幅度减小进口与螺旋桨的距离而不降低计算精度。 相似文献
10.
Unsteady forces, torques and bending moments were predicted for a model podded propulsor unit at various azimuth angles. Predictions in time history include propeller shaft thrust, propulsor unit thrust, normal forces to the propeller shaft bearing, total forces acting on the propulsor unit, propeller shaft torque, blade spindle torque, in-plane and out-of-plane bending moments, and propulsor unit stock shaft torque and bending moments. Analysis was performed for averaged forces and their fluctuations as well. A time-domain unsteady multi-body panel method code, PROPELLA, was further developed for this prediction work. Predictions were compared with a set of time averaged in-house experimental data for a puller-type podded propulsor configuration in the first quadrant operation. Unsteady fluctuations of forces were predicted numerically. Analysis was made for the bending moment on propeller blades, shaft and the propulsor unit stock shaft for azimuth angles from 0° to 45°. It indicates that the magnitude and fluctuation of the forces are significant and they are essential for structural strength and design optimization. The predicted bending moment and global forces on the propulsor unit provide some useful data for ship maneuvering motion and simulation in off-design conditions. 相似文献
11.
Bachmayer R. Whitcomb L.L. Grosenbaugh M.A. 《Oceanic Engineering, IEEE Journal of》2000,25(1):146-159
This paper reports two specific improvements in the finite-dimensional nonlinear dynamical modeling of marine thrusters. Previously reported four-quadrant models have employed thin airfoil theory considering only axial fluid flow and using sinusoidal lift/drag curves. First, we present a thruster model incorporating the effects of rotational fluid velocity and inertia on thruster response. Second, we report a novel method for experimentally determining nonsinusoidal lift/drag curves. The model parameters are identified using experimental thruster data (force, torque, and fluid velocity). The models are evaluated by comparing experimental performance data with numerical model simulations. The data indicates that thruster models incorporating both reported enhancements provide superior accuracy in both transient and steady-state responses 相似文献
12.
可回转桨的水动力模型与操纵性能 总被引：1，自引：0，他引：1
可回转桨在船后形成复杂的流场,难以建立准确的数学模型,因此对其推力进行理论计算十分困难。本文根据实验数据,用神经网络辨识方法建立了船后可回转桨的水动力模型,并在此基础上研究了可回转桨的操纵性能。仿真结果表明：用神经网络系统辨识方法所建立的数学模型能够真实地反映可回转浆的推力特性。本文为研究复杂的水动力问题提供了一种行之有效的方法。 相似文献
13.
Marine cycloidal propulsion system is efficient in maneuvering ships like tugs, ferries, etc. It is capable of vectoring thrust in all direction in a horizontal plane. When used in pair, the system enables a vessel to perform maneuvers like moving sideways, perform rotation about a point, i.e. turning diameter of its own length, etc. In this system, the propeller blades have to change their angle of attack at different angular position of the disc. Due to this reason, the inflow velocity vector to propeller blades changes continuously. The propeller blade oscillates about a vertical axis passing through its body and at the same time rotates about a point. Superposed on these motions is the dynamics of the ship on which the propulsion system is installed. This results in a formidable and challenging hydrodynamics problem. Each of the propeller blade sections could be considered as an aerofoil operating in combined heave and pitch oscillation mode. Due to the constantly varying inflow velocity, the hydrodynamic flow is unsteady. The unsteady hydrodynamic flow is simulated by incorporating the effect of shed vortices at different time instant behind the trailing edge. Due to the kinematics of the problem, the blade is subjected to higher structural deformation and vibration load. The structural deformation and vibration when coupled with the hydrodynamic loading add another level of complexity to the problem. In this paper, the variation of hydrodynamic load on the propeller blade due to steady and unsteady flow is compared. We also model the structural dynamics of the blade and study its effect on the hydrodynamic loading. Finally, we couple the structural dynamics with hydrodynamics loading and study its influence on the propeller blade for different operating regimes. 相似文献
14.
Compact zero-mass pulsatile jet actuators are proposed for low-speed maneuvering and station keeping of small underwater vehicles.1 The flow field of such jets are initially dominated by vortex ring formation. Pinched-off vortices characterize the extremum impulse accumulated by the leading vortex ring in a vortex ring formation process. Relevant parameters in this process are identified in order to design simple and low cost zero-mass pulsatile jet actuators. Thrust optimization of synthetic jets for maximal thrust generation is achieved by enforcing the jet formation number to be around 4. Prototypes of such actuators are built and tested for underwater maneuvering and propulsion. The actuators could be used in two ways: (i) to improve the low-speed maneuvering and station keeping capabilities of traditional propeller driven underwater vehicles, and (ii) as a synthetic jet for flow control and drag reduction at higher cruising speeds. A model for calculating the rotation rate of the underwater vehicle is also proposed and verified. 相似文献
15.
The propulsive efficiency maximization of contra-rotating azimuth propulsor (CRAP) at model scale is investigated through searching the optimal matching rotational speeds of the forward propeller (FP) and rear propeller (RP) of CRAP based on the potential-based panel method. The hydrodynamic performance of CRAP with changing rotational speeds (FP and RP may have different rotational speeds) are calculated. When the inflow velocity is certain, the cubic spline interpolation method is used to get the equal thrust points at which CRAP has the same thrust with the corresponding conventional propeller (CP). Then, the delivered powers at these equal thrust points are further obtained through cubic spline interpolation method. The rotational speeds of FP and RP at the equal thrust point corresponding to the minimal delivered power are the optimal matching rotational speeds of CRAP. The optimal matching calculations are carried out at different inflow velocities. The results of the optimal matching investigation show that CRAP has the lowest delivered powers when FP and RP have the optimal matching rotational speeds and that the energy saving level decreases with the increase of inflow velocity. The optimal matching rotational speed ratio decreases with the increase of inflow velocity. In general, the delivered powers of CRAP having optimal matching rotational speeds at different inflow velocities are obviously smaller than those of CP. 相似文献
16.
In practical maritime conditions, ship hulls experience heave motion due to the action of waves, which can further drive the ship’s propellers to oscillate relative to the surrounding water. In order to investigate the motion of a propeller working behind a surface vessel sailing in waves, a numerical simulation is conducted on a propeller impacted by heave motion in cavitating flow using the Reynolds-averaged Navier-Stokes (RANS) method. The coupling of the propeller’s rotation and translation is fulfilled using equations of motion defined for this purpose. The heave motion is simplified as a periodic motion based on a sinusoidal function. The numerical transmission of information from the unsteady flow field is achieved using the overset grid approach. In this manner, the unsteady thrust coefficient and torque coefficient of propellers in different periods of heave motion are analyzed. A comparative study is implemented on the unsteady cavitation performance and wake characteristics of propeller. With the propeller’s heave motion, the flow field non-uniformity constantly changes the load on the propeller during each revolution period and each heaving period, the propeller load and the wake field are closely related to the variation of heave motion period. The results obtained from the numerical simulation are expected to serve as a useful theoretical reference for the numerical analysis of a propeller in a heave motion. 相似文献
17.
导管桨的尾流不稳定性在其性能评价中非常重要,不但是其能否提供稳定推力的保证,而且也与螺旋桨的尾流噪声直接相关。为了改善导管桨的尾流,提高尾流稳定性,并优化导管桨的流场脉动,根据座头鲸鳍肢前缘结节的仿生原理,对导管桨叶片的导边进行改进,提出了两种仿生桨型,采用IDDES湍流模型对低进速系数下常规导管桨和仿生叶片导管桨进行数值模拟,探究叶片构型对导管桨性能和尾流不稳定性的影响。计算结果表明,前缘结节可以有效降低叶片受力波动的幅值和叶片所受合力的主频域峰值,具有较大结节的叶片对导管桨尾流有明显的优化作用,在尾流远场中扩大了流动稳定区,延后了尾流处涡破碎的发生,改善了能量谱密度的频域分布。进一步,大前缘结节叶片导管桨应用在低速工况下时,可以大量减少尾流泄涡区域的二次涡产生,这是由于前缘结节提升了相邻涡互感的强度,使得尾流更加稳定,而小结节叶片仿生桨型对导管桨尾流则无明显优化作用。研究方法和成果可为螺旋桨尤其是导管桨尾流不稳定性研究提供参考,不仅验证了前缘结节在导管桨叶片应用的合理性,而且揭示了其优化尾流稳定性的机理。 相似文献
18.
An offshore vessel with a dynamic positioning system (DP system) needs fast response to produce thrust to counteract the environmental forces acting on it for the purpose of maintaining its position and heading as close as possible to the working position. Therefore, quick and effective modulation of the thrust is the problem to determine the thrust and the rotation angle of the thruster devices of the ship. This paper presents an effective optimum control for a thruster system, using the sequential quadratic method to achieve economical and effective modulation of the thrust and the direction of the thruster. An optimum control study of a 2280 tons DP coring vessel with five rotary azimuth thruster marine positioning is studied in detail, which can quickly and exactly estimate the thrusts and angles of direction of all the thrusters. The results can provide a valuable thruster system for a dynamically positioned vessel. 相似文献
19.
PETREL,a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV (autonomous underwater vehicle).It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile.In this paper,theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration.In addition,due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes,the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced,and the tailored dynamic equations of the hybrid glider are formulated.Moreover,the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials. 相似文献
20.
半潜式平台动力定位系统控制力动态约束分配法 总被引：1，自引：0，他引：1
半潜式平台动力定位推力分配系统通过计算每个推力器的推力和推力角,将控制力分配到推力系统的各推力器上。基于系统耗能最小模式,根据推力器之间的损失模型,通过动态设置推力可行域,将推力分配问题转化为求解二次型优化模型。考虑推力器的物理性能,以推力变化率和转角变化速率为控制参数,利用序列二次规划法得到数值计算结果。该方法充分考虑推力器的物理性能,降低推力器的机械磨损,且可以避免处理可行域为非凸集问题,有效地提高推力器的推力效率。 相似文献