共查询到20条相似文献，搜索用时 23 毫秒
1.
Simulations of water movement and solute transport through different soil texture configurations under negative‐pressure irrigation 
下载免费PDF全文
下载免费PDF全文 This study examined the effects of different soil texture configurations on water movement and solute transport to provide a reliable scientific basis for the application of negative‐pressure irrigation (NPI) technology. HYDRUS‐2D was used to analyse water movement and solute transport under NPI. The main results are as follows: (a) HYDRUS‐2D can be used to simulate water movement and solute transport under NPI, as there was good agreement between the simulated and measured values for water contents, NaCl concentrations, cumulative water infiltration, and wetting distances in the horizontal and vertical directions; the Nash–Sutcliffe efficiency coefficients were in the range of 0.94–0.97. (b) Layered soils have obvious effects on water movement under NPI. With the emitter position in the loam layer, when a coarse texture of loamy sand was present below the loam layer (namely, L‐LS), irrigation water accumulated in the topsoil, and this led to an increase in evaporation compared with the homogeneous loam profile. However, fine texture silty loam or silty clay loam layers beneath the loam layer (namely, L‐SiL or L‐SiCL, respectively) was more conducive to water infiltration into the lower layer, and this increased the amount of water infiltration and simultaneously reduced the surface evaporation effectively. (c) Layered soils have obvious effects on solute transport under NPI, and salt accumulation will readily occur in the clay‐rich soil layer at the interface. The maximum soil salt accumulation of L‐LS occurred above the soil interface between the two soil layers with a value of 21.80 g/kg; however, for L‐SiCL and L‐SiL, the maximum salt accumulation occurred below the soil interface between the two soil layers, with values of 23.80 g/kg and 20.08 g/kg, respectively. (d) Interlayered soils showed remarkable changes in the water infiltration characteristics and salt‐leaching intensities under NPI, and the properties for the soil profile with a silty loam interlayer were better than those for the soil profile with a silty clay loam interlayer. The soil profile with a loamy sand interlayer had the lowest amount of water infiltration, which resulted in reductions of the salt‐leaching intensities. Thus, NPI is clearly not suitable for loamy sand soil. Overall, the results demonstrated that soil texture configurations affected water movement and solute transport under NPI. Therefore, careful consideration should be given to the use of NPI to achieve target soil water and solution conditions and reduce water loss. 相似文献
2.
3.
The interaction effects of different applied ratios of a hydrophilic polymer (Superab A200) (0, 0.2, 0.6% w/w) under various soil salinity levels (initial salinity, 4 and 8 ms/cm) were evaluated on available water content (AWC), biomass, and water use efficiency for corn grown in loamy sand and sandy clay loam soils. The results showed that the highest AWC was measured at the lowest soil salinity. The application of 0.6% w/w of the polymer at the lowest salinity level increased the AWC by 2.2 and 1.2 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. The analysis of variance of data showed that the effect of salinity was significant on biomass and water use efficiency of corn in the loamy sand and sandy clay loam soils. The highest amounts of these traits were measured in soils with the lowest salinity level. Application of polymer at the rate of 0.6% in the loamy sand soil and at the rate of 0.2% in the sandy clay loam soil resulted in the highest aerial and root biomass and water use efficiency for corn. At these polymer rates the amounts of water use efficiency for corn were 2.6 and 1.7 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. Thus, the use of hydrophilic polymer in soils especially in the sandy soils increases soil water holding capacity, yield, and water use efficiency of plant. On the other hand, decreases the negative effect of soil salinity on plant and helps for irrigation projects to succeed in arid and semi‐arid areas. 相似文献
4.
Th. Verhaegen 《地球表面变化过程与地形》1987,12(2):185-194
The objective of this study was to examine the possibility of determining soil erodibility of loamy soils with small flumes. This was done by comparing the classification of soil erodibility obtained in the field with that obtained in the laboratory. Therefore twenty soils with a texture varying from silty loam to sandy loam were selected from the Leuven region. The erosion in the field was determined by measuring the volumetric evolution of the rill pattern. In the laboratory the soils were tested with a rainfall simulator and small flumes. The conclusion was that for loamy soils the flume experiments are a quick, simple, and reliable method for the determination of the relative soil erodibility. 相似文献
5.
Th. Verhaegen 《地球表面变化过程与地形》1984,9(6):499-507
Twenty soils from the Leuven region were tested in the laboratory with a rainfall simulator. Their texture varied from loam to loamy sand. On the basis of the results obtained, they were classified as a function of the runoff and splash erodibility. For every soil, several properties were determined and tentatively used to explain the classifications based on the runoff and splash erodibility. Significant negative correlations were found between silt content, aggregate stability, C5–10 index, water content at saturation, and cohesion on the one side and erodibility on the other; a positive correlation was found between sand content and erodibility. 相似文献
6.
The Tianjin coastal area is a typical soft soil region,where the soil is a marine deposit of the late Quaternary.The soil dynamic parameters from seismic risk assessment reports are collected,and drilling of 15 holes was carried out to sample the soils and measure their dynamic characteristics.The data was divided into 7 types based on lithology,namely,muddy clay,muddy silty clay,silt,silty clay,clay,silty sand and fine sand.Statistics of the dynamic parameters of these soils are collected to obtain the mea... 相似文献
7.
《Ground Water Monitoring & Remediation》1988,8(2):49-50
Currently, vadose zone monitoring is required under the Resource Conservation and Recovery Act (RCRA) only at land treatment facilities. Contaminant leak detection through ground water monitoring is very important, but it is considered to be after the fact. Remedial action costs can be reduced considerably by monitoring the vadose zone for compounds that exhibit high rates of movement. Volatile organic compounds (VOCs) exhibit this property and are present at many municipal landfills, recycling facilities, and treatment storage and disposal facilities (TSDFs). Through the authors'personal experience, it has been noted that gaseous phase transport of VOCs through the vadose zone is at least an order of magnitude greater than advective transport of VOCs in ground water. Therefore, VOCs in soil gas are an effective early warning leak detection parameter. Downward movement of leachate can be intercepted by porous cup lysimeters. Attenuation in the vadose zone slows the apparent movement of contaminants; however, it is only a matter of time before leachate reaches the water table. The authors believe that soil-gas and pore-water monitoring should and eventually will be required at all RCRA sites. If vadose zone monitoring becomes an additional requirement under RCRA, both the facility owner and the taxpayer will benefit. During the interim, facility owners can benefit by employing vadose zone monitoring techniques coupled with either qualitative or quantitative chemical analyses. 相似文献
8.
9.
Hillary Agaba Lawrence Justus Baguma Orikiriza John Francis Osoto Esegu Joseph Obua John David Kabasa Aloys Hüttermann 《洁净——土壤、空气、水》2010,38(4):328-335
The effect of super absorbent polyacrylate (SAP) hydrogel amendment to different soil types on plant available water (PAW), evapotranspiration and survival of Eucalyptus grandis, Eucalyptus citriodora, Pinus caribaea, Araucaria cunninghamii, Melia volkensii, Grevillea robusta, Azadirachta indica, Maesopsis eminii and Terminalia superba was investigated. The seedlings were potted in 3 kg size polythene bags filled with sand, loam, silt loam, sandy loam and clay soils, amended at 0 (control), 0.2 and 0.4% w/w hydrogel. The tree seedlings were allowed to grow normally with routine uniform watering in a glass house set up for a period of eight weeks, after which they were subjected to drought conditions by not watering any further. The 0.4% hydrogel amendment significantly (p < 0.05) increased the PAW by a factor of about three in sand, two fold in silt loam and one fold in sandy loam, loam and clay soils compared to the control. Similarly, the addition of either 0.2 or 0.4% hydrogel to the five soil types resulted in prolonged tree survival compared to the controls. Araucaria cunninghammi survived longest at 153 days, while Maesopsis eminii survived least (95 days) in sand amended at 0.4% after subjection to desiccation. Evapotranspiration was reduced in eight of the nine tree species grown in sandy loam, loam, silt loam and clay soils amended at 0.4% hydrogel. It is probable that soil amendment with SAP decreased the hydraulic soil conductivity that might reduce plant transpiration and soil evaporation. 相似文献
10.
Differences in preferential flow with antecedent moisture conditions and soil texture: Implications for subsurface P transport 总被引：2，自引：0，他引：2
Preferential flowpaths transport phosphorus (P) to agricultural tile drains. However, if and to what extent this may vary with soil texture, moisture conditions, and P placement is poorly understood. This study investigated (a) interactions between soil texture, antecedent moisture conditions, and the relative contributions of matrix and preferential flow and (b) associated P distributions through the soil profile when fertilizers were applied to the surface or subsurface. Brilliant blue dye was used to stain subsurface flowpaths in clay and silt loam plots during simulated rainfall events under wet and dry conditions. Fertilizer P was applied to the surface or via subsurface placement to plots of different soil texture and moisture condition. Photographs of dye stains were analysed to classify the flow patterns as matrix dominated or macropore dominated, and soils within plots were analysed for their water‐extractable P (WEP) content. Preferential flow occurred under all soil texture and moisture conditions. Dye penetrated deeper into clay soils via macropores and had lower interaction with the soil matrix, compared with silt loam soil. Moisture conditions influenced preferential flowpaths in clay, with dry clay having deeper infiltration (92 ± 7.6 cm) and less dye–matrix interaction than wet clay (77 ± 4.7 cm). Depth of staining did not differ between wet (56 ± 7.2 cm) and dry (50 ± 6.6 cm) silt loam, nor did dominant flowpaths. WEP distribution in the top 10 cm of the soil profile differed with fertilizer placement, but no differences in soil WEP were observed at depth. These results demonstrate that large rainfall events following drought conditions in clay soil may be prone to rapid P transport to tile drains due to increased preferential flow, whereas flow in silt loams is less affected by antecedent moisture. Subsurface placement of fertilizer may minimize the risk of subsurface P transport, particularily in clay. 相似文献
11.
The partitioning of rainfall into surface runoff and infiltration influences many other aspects of the hydrologic cycle including evapotranspiration, deep drainage and soil moisture. This partitioning is an instantaneous non-linear process that is strongly dependent on rainfall rate, soil moisture and soil hydraulic properties. Though all rainfall datasets involve some degree of spatial or temporal averaging, it is not understood how this averaging affects simulated partitioning and the land surface water balance across a wide range of soil and climate types. We used a one-dimensional physics-based model of the near-surface unsaturated zone to compare the effects of different rainfall discretization (5-min point-scale; hourly point-scale; hourly 0.125° gridded) on the simulated partitioning of rainfall for many locations across the United States. Coarser temporal resolution rainfall data underpredicted seasonal surface runoff for all soil types except those with very high infiltration capacities (i.e., sand, loamy sand). Soils with intermediate infiltration capacities (i.e., loam, sandy loam) were the most affected, with less than half of the expected surface runoff produced in most soil types when the gridded rainfall dataset was used as input. The impact of averaging on the water balance was less extreme but non-negligible, with the hourly point-scale predictions exhibiting median evapotranspiration, drainage and soil moisture values within 10% of those predicted using the higher resolution 5-min rainfall. Water balance impacts were greater using the gridded hourly dataset, with average underpredictions of ET up to 27% in fine-grained soils. The results suggest that “hyperresolution” modelling at continental to global scales may produce inaccurate predictions if there is not parallel effort to produce higher resolution precipitation inputs or sub-grid precipitation parameterizations. 相似文献
12.
Neal D. Durant Vernon B. Myers Lawrence A. Eccles 《Ground Water Monitoring & Remediation》1993,13(1):151-158
The U.S. Environmental Protection Agency (EPA) recently proposed to amend federal regulations to require vadose zone monitoring at certain hazardous waste facilities. To support this proposal, EPA evaluated previous policy on vadose zone monitoring and examined advances in vadose zone monitoring technology. Changes in EPA vadose zone monitoring policy were driven by demonstrated advances in the available monitoring technology and improvements in understanding of vadose zone processes/When used under the appropriate conditions, currently available direct and indirect monitoring methods can effectively detect contamination that may leak from hazardous waste facilities into the vadose zone. Direct techniques examined include soil-core monitoring and soil-pore liquid monitoring. Indirect techniques examined include soil-gas monitoring, neutron moderation, complex resistivity, ground-penetrating radar, and electrical resistivity. Properly designed vadose zone monitoring networks can act as a complement to saturated zone monitoring networks at numerous hazardous waste facilities. At certain facilities, particularly those in arid climates where the saturated zone is relatively deep, effective vadose zone monitoring may allow a reduction in the scope of saturated zone monitoring programs. 相似文献
13.
14.
Two lysimeters with the same dimensions were provided, and filled with the same loam clay. On the soil surface of one lysimeter, grass was planted to compare the hydrologic response of the grassed lysimeter with that of the other bare soil lysimeter.
About half of the runoff from the bare soil lysimeter occurred as overland flow, the rest being groundwater flow. Overland flow scarcely occurred from the grassed lysimeter. Grass roots that developed deep into the soil layer play an important role in increasing the infiltration rate as well as in drying the soil uniformly throughout the soil layer by evapotranspiration, preparing for high infiltration and large rainwater storage for the subsequent rainfall event. Accordingly, the total loss by evapotranspiration from the grassed soil amounts to almost twice that from the bare soil.
For an evaporation- and evapotranspiration-prohibited experiment, the recession characteristics from a saturation state showed similar features for the bare and grassed soils, indicating the same microstructure of high moisture reservability for both soils.
The well-developed grass root system reformed the soil structure considerably to produce the seemingly contradicting characteristics of high moisture conductivity and high moisture reservability; i.e. a high infiltration rate and prolonged groundwater discharge.
Finally, the importance of the initial soil moisture in the rainfall-runoff process, rainfall loss and runoff ratio is stressed. 相似文献
15.
天津滨海场地土动力学参数研究 总被引：2，自引：2，他引：0
天津滨海地区是典型的软土区,属晚第四系以来的浅海相沉积软土。本文收集了该地区地震安全性评价报告中的土动力学参数的实验资料,并补充了15个钻孔的测试实验,统计分析了淤泥质粘土、淤泥质粉质粘土、粉土、粉质粘土、粘土、粉砂、细砂等7种土类的实测土动力学参数,给出了它们在不同深度下的动剪切模量比和阻尼比的统计值。然后,选取了2个典型钻孔并建立了土层地震反应分析模型,分别运用本文统计值、94规范值和袁晓铭等(2000)的推荐值进行土层地震反应计算,从反应谱形状、地表峰值加速度和反应谱特征周期等方面说明了本文统计值的适用性和针对性。本文的研究成果对天津滨海地区各类工程建设的场地地震安全性评价工作具有一定的借鉴和参考价值,且有利于该地区工程场地地震安全性评价工作的开展。 相似文献
16.
《Ground Water Monitoring & Remediation》1985,5(3):75-80
Increasingly, regulations by federal, state and local agencies are being developed that require the installation of vadose zone monitoring systems for hazardous chemical facilities in addition to, or in lieu of, conventional ground water monitoring wells. Compared to a ground water monitoring approach, vadose zone monitoring systems may permit earlier detection of chemical leakage and less costly cleanup of contamination. The effective use of vadose zone monitoring systems in detecting contamination depends on many factors. Without proper consideration of these factors, a vadose zone monitoring system may not give as high a level of reliability as a ground water monitoring system.
Major factors to consider in installing a vadose zone monitoring system are: type of instrument to use, number of instruments, depth and location of instruments, and frequency of monitoring. Means to evaluate these factors in a comprehensive fashion have been lacking. Based on recent experience in installing and operating vadose zone monitoring systems, criteria and methods useful in resolving the preceding factors have been developed. Types of instruments can be classified as either direct (lysimeter, vapor probe) or indirect (tensiometer, conductivity probe). A combination of the two is needed for reliability. The depth, location and number of instruments depend on the geometry of the facility, the number and size of likely contaminant leakage points in engineered barriers, properties of the material being monitored, the effective radius of monitoring for each instrument, vadose zone properties, and types of remedial actions that are available. The freqency of monitoring largely depends on the rate of movement of the contaminant. Evaluating the preceding factors requires some level of modeling and preliminary field testing. 相似文献
Major factors to consider in installing a vadose zone monitoring system are: type of instrument to use, number of instruments, depth and location of instruments, and frequency of monitoring. Means to evaluate these factors in a comprehensive fashion have been lacking. Based on recent experience in installing and operating vadose zone monitoring systems, criteria and methods useful in resolving the preceding factors have been developed. Types of instruments can be classified as either direct (lysimeter, vapor probe) or indirect (tensiometer, conductivity probe). A combination of the two is needed for reliability. The depth, location and number of instruments depend on the geometry of the facility, the number and size of likely contaminant leakage points in engineered barriers, properties of the material being monitored, the effective radius of monitoring for each instrument, vadose zone properties, and types of remedial actions that are available. The freqency of monitoring largely depends on the rate of movement of the contaminant. Evaluating the preceding factors requires some level of modeling and preliminary field testing. 相似文献
17.
Ravi V. Kolhatkar Hong Luo Erin C. Berns Christopher Gaule Joe Watterson 《Ground Water Monitoring & Remediation》2021,41(2):48-60
Vapor intrusion (VI) occurs when volatile contaminants in the subsurface migrate through the vadose zone into overlying buildings. The 2015 U.S. EPA petroleum VI guidance recommends that additional investigation of the VI risk from gasoline hydrocarbons at the underground storage tank (UST) sites is not necessary where the vertical distance between a building and a vapor source exceeds a recommended vertical screening distance. However, due to the lack of soil-gas data on the attenuation of ethylene dibromide (EDB), additional VI investigations to evaluate VI risk from EDB are recommended at UST sites with leaded gasoline releases containing EDB. We analyzed soil-gas and groundwater concentrations of EDB from eight petroleum UST sites using a new analytical method with soil-gas detection limit <0.16 μg/m3 EDB (VI screening level at the 10−6 risk level). The analysis included (1) assessing the frequency of EDB detections ≤0.16 μg/m3 at various vertical separation distances and (2) predicting vertical screening distances for EDB using the U.S. EPA PVIScreen model for different soil types in the vadose zone above dissolved-phase and LNAPL sources. Ranges of estimated aerobic biodegradation rate constants for EDB, air exchange rates for residential buildings, and source vapor concentrations for other constituents were combined with conservative estimates of EDB source concentrations as model inputs. Concentrations of EDB in soil-gas indicated that the U.S. EPA recommended vertical screening distances are protective of VI risk from EDB. Conversely, vertical screening distances predicted by modeling were >6 ft (1.8 m) for sites with sand and loam soil above dissolved phase sources and >15 ft (4.6 m) for sites with sand soil above LNAPL sources. This predicted dependence on the vapor source type and soil type in the vadose zone highlights the importance of soil characterization for VI screening at sites with EDB sources. 相似文献
18.
Ravi V. Kolhatkar Matthew A. Lahvis Ian Hers John T. Wilson Emma Luo Parisa Jourabchi 《Ground Water Monitoring & Remediation》2019,39(4):41-51
Vapor intrusion (VI) involves migration of volatile contaminants from subsurface through unsaturated soil into overlying buildings. In 2015, the US EPA recommended an approach for screening VI risks associated with gasoline releases from underground storage tank (UST) sites. Additional assessment of the VI risk from petroleum hydrocarbons was deemed unnecessary for buildings separated from vapor sources by more than recommended vertical screening distances. However, these vertical screening distances did not apply to potential VI risks associated with releases of former leaded gasoline containing 1,2-dichloroethane (1,2-DCA), because of a lack of empirical data on the attenuation of 1,2-DCA in soil gas. This study empirically evaluated 144 paired measurements of 1,2-DCA concentrations in soil gas and groundwater collected at 47 petroleum UST sites combined with BioVapor modeling. This included (1) assessing the frequency of 1,2-DCA detections in soil gas below 10−6 risk-based screening levels at different vertical separation distances and (2) comparing the US EPA recommended vertical screening distances with those predicted by BioVapor modeling. Vertical screening distances were predicted for different soil types using aerobic biodegradation rate constants estimated from the measured soil-gas data combined with conservative estimates of source concentrations. The modeling indicates that the vertical screening distance of 6 feet (1.8 m) recommended for dissolved-phase sources is applicable for 1,2-DCA below certain threshold concentrations in groundwater, while 15 feet (4.6 m) recommended for light nonaqueous phase liquid (LNAPL) sources is applicable for sites with clay and loam soils in the vadose zone, but not sand, if 1,2-DCA concentrations in groundwater exceed 150 μg/L. This dependence of the predicted vertical screening distances on soil type places added emphasis on proper soil characterization for VI screening at sites with 1,2-DCA sources. The soil-gas data suggests that a vertical screening distance of 15 feet (4.6 m) is necessary for both dissolved-phase and LNAPL sources. 相似文献
19.
Tomáš Laburda Josef Krása David Zumr Jan Devátý Michal Vrána Nives Zambon Lisbeth Lolk Johannsen Andreas Klik Peter Strauss Tomáš Dostál 《地球表面变化过程与地形》2021,46(5):1067-1082
An understanding of splash erosion is the basis to describe the impact of rain characteristics on soil disturbance. In typical splash cup experiments, splashed soil is collected, filtered, and weighed. As a way to collect additional data, our experiments have been supplemented by a photogrammetric approach. A total of three soils were tested across three sites, one in the Czech Republic and two in Austria, all equipped with rain gauges and disdrometers to measure rainfall parameters. The structure from motion multiview stereo (SfM-MVS) photogrammetric method was used to measure the raindrops impact on the soil surface. The images were processed using Agisoft PhotoScan, resulting in orthophotos and digital elevation models (DEMs) with a resolution of 0.1 mm/pix. The surface statistics included the mean surface height (whose standard deviation was used as a measure of surface roughness), slope, and other parameters. These parameters were evaluated depending on soil texture and rainfall parameters. The results show a linear correlation between consolidation and splash erosion with a coefficient of determination (R2) of approximately 0.65 for all three soils. When comparing the change in soil volume with rainfall parameters, the best correlation was found with the maximum 30-minintensity (I30), resulting in R2 values of 0.48 (soil A, silt loam, 26% clay), 0.59 (soil B, silt loam, 18% clay), and 0.68 (soil C, loamy sand, 12% clay). The initial increase in the sample volume for the lowest splashed mass corresponds with the increase in the clay content of each of the soils. Soil A swells the most. Soil B swells less. Soil C does not swell at all and consolidates the most. We derived the relationship between the photogrammetrically measured change in surface height and the splash erosion (measured by weight) by accounting for the effect of the clay content. 相似文献
20.
Air-borne passive microwave remote sensors measure soil moisture at the footprint scale, a scale of several hundred square meters or kilometers that encompasses different characteristic combinations of soil, topography, vegetation, and climate. Studies of within-footprint variability of soil moisture are needed to determine the factors governing hydrologic processes and their relative importance, as well as to test the efficacy of remote sensors. Gridded ground-based impedance probe water content data and aircraft-mounted Electronically Scanned Thinned Array Radiometer (ESTAR) pixel-average soil moisture data were used to investigate the spatio-temporal evolution and time-stable characteristics of soil moisture in three selected (LW03, LW13, LW21) footprints from the Southern Great Plains 1997 (SGP97) Hydrology Experiment. Better time-stable features were observed within a footprint containing sandy loam soil than within two pixels containing silty loam soil. Additionally, flat topography with split wheat/grass land cover produced the largest spatio-temporal variability and the least time stability in soil moisture patterns. A comparison of ground-based and remote sensing data showed that ESTAR footprint-average soil moisture was well calibrated for the LW03 pixel with sandy loam soil, rolling topography, and pasture land cover, but improved calibration is warranted for the LW13 (silty loam soil, rolling topography, pasture land) and LW21 (silty loam soil, flat topography, split vegetation of wheat and grass land with tillage practice) pixels. Footprint-scale variability and associated nonlinear soil moisture dynamics may prove to be critical in the regional-scale hydroclimatic models. 相似文献