共查询到20条相似文献，搜索用时 390 毫秒
1.
Ronggao Qin Yanqing Wu Zengguang Xu Derrick Xie Chi Zhang 《Hydrogeology Journal》2013,21(6):1235-1246
The combined influence of dip angle and adsorption heterogeneity on solute transport mechanisms in heterogeneous media can be understood by performing simulations of steady-state flow and transient transport in a heterogeneous aquifer with dipping anisotropy. Reactive and non-reactive contaminant transport in various types of heterogeneous aquifer is studied by simulations. The hydraulic conductivity (K) of the heterogeneous aquifer is generated by HYDRO_GEN with a Gaussian correlation spectrum. By considering the heterogeneity of the adsorption distribution coefficient (K d), a perfect negative correlation between lnK and lnK d is obtained by using the spherical grains model. The generated K and K d are used as input to groundwater flow and transport models to investigate the effects of dipping sedimentary heterogeneity on contaminant plume evolution. Simulation results showed that the magnitude of the dip angle strongly controls the plume evolution in the studied anisotropic and heterogeneous aquifer. The retarded average pore-water velocity (v/R) of the adsorption model significantly controls the horizontal spreading of the plume. The bottom plume is intensively retarded in the zones between the dipping lenses of lower hydraulic conductivity and the no-flow bottom boundary. The implications of these findings are very important for the management of contaminated heterogeneous aquifers. 相似文献
2.
A three-dimensional numerical flow and contaminant transport model is developed to investigate the effect of variable hydraulic conductivity on average mass transfer coefficients associated with the dissolution of dense nonaqueous phase liquid (DNAPL) pools in heterogeneous, water-saturated subsurface formations. Randomly generated, three-dimensional hydraulic conductivity fields are used to represent a heterogeneous confined aquifer. Model simulations indicate that the average mass transfer coefficient is inversely proportional to the variance of the log-transformed hydraulic conductivity. A power law correlation relating the Sherwood number to the variance of the log-transformed hydraulic conductivity and appropriate Peclet numbers is developed. A reasonable fit between predicted and numerically determined mass transfer coefficients is observed. 相似文献
3.
随机水文地质学方法,较传统的确定性方法而言,是解决非均质含水层中水流和溶质运移问题的一种更为合理的手段。据以往研究,假设渗透系数场遵循对数正态分布,利用直接傅立叶变换方法来生成渗透系数随机场。应用基于随机理论的蒙特卡罗方法,来研究渗透系数的空间变异性对污染物运移结果的影响。实例研究表明,污染物在含水层中运移过程中污染羽的展布范围(二阶矩)随着渗透系数空间变异方差的增大而扩大,而污染羽在空间上的质心位置(一阶矩)基本不受方差的影响,仅取决于渗透系数随机场的均值大小。另外还分析了污染羽在各点的浓度变化方差和变异系数分别随渗透系数变异方差的变化状况。 相似文献
4.
Mohamed Ahmed Khalil 《Arabian Journal of Geosciences》2011,4(1-2):269-281
Estimation of hydraulic conductivity from surface resistivity measurements is one of the most difficult and challenging hydrogeophysical targets. The promising side of this relation is the analogy between electric current flow and water flow, whereas the grand ambiguity is the non-dimensionality between both two quantities. Imaginary surface conductivity component is used recently to deduce the hydraulic conductivity via complex resistivity measurements. Since there are similar properties between imaginary (out-of-phase) and real (in-phase) surface conductivity components, the latter is used in this paper to predict the hydraulic conductivity. Two mathematical parameters were determined to express the electrical equivalent of hydraulic conductivity in sand and clay systems based on the mode of electrical double-layer formation in both systems. The reliability of the proposed method is tested through applying on two datasets representing sand and clay systems. The first dataset is a clean sand and gravel aquifer in the Keritis basin in Chania, Crete, Greece. The second is mostly clayey sand aquifer in Wadi El-Assuity, Egypt. Application of the present approach in these two cases resulted in promising nearly identical values with the measured hydraulic conductivity via pumping test or geometric hydraulic conductivity via grain size analysis. 相似文献
5.
Sensitivity Analysis of a Combined Groundwater Flow and Solute Transport Model Using Local-Grid Refinement: A Case Study 总被引：1，自引：0，他引：1
Combining groundwater flow models with solute transport models represents a common challenge in groundwater resources assessments and contaminant transport modeling. Groundwater flow models are usually constructed at somewhat larger scales (involving a coarser discretization) to include natural boundary conditions. They are commonly calibrated using observed groundwater levels and flows (if available). The groundwater solute transport models may be constructed at a smaller scale with finer discretization than the flow models in order to accurately delineate the solute source and the modeled target, to capture any heterogeneity that may affect contaminant migration, and to minimize numerical dispersion while still maintaining a reasonable computing time. The solution that is explored here is based on defining a finer grid subdomain within a larger coarser domain. The local-grid refinement (LGR) implemented in the Modular 3D finite-difference ground-water flow model (MODFLOW) code has such a provision to simulate groundwater flow in two nested grids: a higher-resolution sub-grid within a coarse grid. Under the premise that the interface between both models was well defined, a comprehensive sensitivity and uncertainty analysis was performed whereby the effect of a parameter perturbation in a coarser-grid model on transport predictions using a higher-resolution grid was quantified. This approach was tested for a groundwater flow and solute transport analysis in support of a safety evaluation of the future Belgian near-surface radioactive waste disposal facility. Our reference coarse-grid groundwater flow model was coupled with a smaller fine sub-grid model in two different ways. While the reference flow model was calibrated using observed groundwater levels at a scale commensurate with that of the coarse-grid model, the fine sub-grid model was used to run a solute transport simulation quantifying concentrations in a hypothetical well nearby the disposal facility. When LGR coupling was compared to a one-way coupling, LGR was found to provide a smoother flow solution resulting in a more CPU-efficient transport solution. Parameter sensitivities performed with the groundwater flow model resulted in sensitivities at the head observation locations. These sensitivities identified the recharge as the most sensitive parameter, with the hydraulic conductivity of the upper aquifer as the second most sensitive parameter in regard to calculated groundwater heads. Based on one-percent sensitivity maps, the spatial distribution of the observations with the highest sensitivities is slightly different for the upper aquifer hydraulic conductivity than for recharge. Sensitivity analyses were further performed to assess the prediction scaled sensitivities for hypothetical contaminant concentrations using the combined groundwater flow and solute transport models. Including all pertinent parameters into the sensitivity analysis identified the hydraulic conductivity of the upper aquifer as the most sensitive parameter with regard to the prediction of contaminant concentrations. 相似文献
6.
基于不同地质统计方法的渗透系数场对污染物运移的影响 总被引：1，自引：0，他引：1
渗透系数场的空间变异性是影响污染物运移结果的决定因素,而地质统计方法是解决渗透系数空间变异性的主要技术手段。本文利用野外场地实测数据,采用普通克里格法和指示克里格法、顺序高斯模拟法和顺序指示模拟法四种地质统计方法,插值估测和模拟再现随机渗透系数场,进而对比研究四种渗透系数场对大尺度污染物运移的影响。研究结果表明,污染羽的质心位置（一阶矩）主要由渗透系数的平均值来决定;污染羽在空间上的展布范围（二阶矩）主要受渗透系数空间变异方差的影响;条件模拟克服了估计法的平滑效果,较好地再现真实曲线的波动性,渗透系数（ lnK）估计方差与污染羽空间二阶矩随着条件模拟次数的增加而减小,并且顺序指示模拟程度更加明显。 相似文献
7.
The combined effect of clay and moisture content on the behavior of remolded unsaturated soils 总被引：2，自引：0，他引：2
Naser A. Al-Shayea 《Engineering Geology》2001,62(4):319-342
The behavior of unsaturated clayey soil is highly influenced by the coupled interaction between water and clay content. Various aspects of the behavior of artificial clay–sand mixtures with variable water content were experimentally studied. Laboratory tests were utilized for the determination of consistency limits, the stress–strain relationship, strength parameters, hydraulic conductivity, and volume change characteristics for various combinations of water and clay content in soil mixtures.
Results presented for various clay–sand mixtures include: new normalized consistency limits; the combined effect of clay content and water content on the stress–strain relationship and on the strength parameters (c and φ); and the effect of clay content on hydraulic conductivity and swelling potential. The cohesion of clayey sand is found to increase with increasing water content to a certain limit, above which it decreases. The angle of internal friction for clayey sand is found generally to decrease with increasing water content. The degree of saturation is found to be better than the water content in explaining the strength behavior. The hydraulic conductivity sharply decreases with increasing clay content up to 40% beyond which the reduction becomes less significant. Simple empirical equations are proposed for predicting the swelling potential of clayey soils as a function of either the clay content or plasticity index. 相似文献
8.
通过实验室一维砂柱模拟研究了不同影响因素下空气扰动技术(air sparging,AS)修复氯苯污染地下水的效果,包括介质渗透性、曝气方式、共存污染物、残余饱和态氯苯。结果表明:介质渗透性极大地影响着AS的效果,渗透系数越大,去除效果越好。对渗透系数为10-5m/s数量级及其以下的介质应用AS较为困难;在曝气时间相同的情况下,对于渗透系数为5.1×10-4m/s的中砂,脉冲曝气较连续曝气效果好,对于渗透系数为6.2×10-3m/s的粗砂,2种曝气方式效果相仿;苯和氯苯共存时各污染物的去除存在协同作用;AS对残余饱和态氯苯的去除存在着明显的拖尾效应。 相似文献
9.
Application of multiple-point geostatistics on modelling groundwater flow and transport in a cross-bedded aquifer (Belgium) 总被引：3，自引：1，他引：2
Sedimentological processes often result in complex three-dimensional subsurface heterogeneity of hydrogeological parameter values. Variogram-based stochastic approaches are often not able to describe heterogeneity in such complex geological environments. This work shows how multiple-point geostatistics can be applied in a realistic hydrogeological application to determine the impact of complex geological heterogeneity on groundwater flow and transport. The approach is applied to a real aquifer in Belgium that exhibits a complex sedimentary heterogeneity and anisotropy. A training image is constructed based on geological and hydrogeological field data. Multiple-point statistics are borrowed from this training image to simulate hydrofacies occurrence, while intrafacies permeability variability is simulated using conventional variogram-based geostatistical methods. The simulated hydraulic conductivity realizations are used as input to a groundwater flow and transport model to investigate the effect of small-scale sedimentary heterogeneity on contaminant plume migration. Results show that small-scale sedimentary heterogeneity has a significant effect on contaminant transport in the studied aquifer. The uncertainty on the spatial facies distribution and intrafacies hydraulic conductivity distribution results in a significant uncertainty on the calculated concentration distribution. Comparison with standard variogram-based techniques shows that multiple-point geostatistics allow better reproduction of irregularly shaped low-permeability clay drapes that influence solute transport. 相似文献
10.
3D-electrical resistivity tomography monitoring of salt transport in homogeneous and layered soil samples 总被引：1，自引：1，他引：0
Cesare Comina Renato Maria Cosentini Gabriele Della Vecchia Sebastiano Foti Guido Musso 《Acta Geotechnica》2011,6(4):195-203
Monitoring transport of dissolved substances in soil deposits is particularly relevant where safety is concerned, as in the
case of geo-environmental barriers. Geophysical methods are very appealing, since they cover a wide domain, localising possible
preferential flow paths and providing reliable links between geophysical quantities and hydrological variables. This paper
describes a 3D laboratory application of electrical resistivity tomography (ERT) used to monitor solute transport processes.
Dissolution and transport tests on both homogeneous and heterogeneous samples were conducted in an instrumented oedometer
cell. ERT was used to create maps of electrical conductivity of the monitored domain at different time intervals and to estimate
concentration variations within the interstitial fluid. Comparisons with finite element simulations of the transport processes
were performed to check the consistency of the results. Tests confirmed that the technique can monitor salt transport, infer
the hydro-chemical behaviour of heterogeneous geomaterials and evaluate the performances of clay barriers. 相似文献
11.
分析了运移参数的变化对GCL中污染物运移的影响。从衬垫底部浓度比、对流和扩散通量、污染物累积运移量等方面,对污染物在GCL中的运移进行了计算。结果表明,减小渗透系数和扩散系数可以有效减缓衬垫底部浓度比的增加速度。渗透系数对对流通量的大小、扩散通量的变化速度的影响较大;扩散系数主要影响最大扩散通量。当渗透系数较大时,可以忽略扩散累积运移量,用对流累积运移量代替总累积运移量引起的误差很小。当渗透系数较小时,忽略扩散运移量可能产生较大的误差,尤其是在扩散系数也较大的情况下误差更加明显。 相似文献
12.
Modern geostatistical techniques allow the generation of high-resolution heterogeneous models of hydraulic conductivity containing millions to billions of cells. Selective upscaling is a numerical approach for the change of scale of fine-scale hydraulic conductivity models into coarser scale models that are suitable for numerical simulations of groundwater flow and mass transport. Selective upscaling uses an elastic gridding technique to selectively determine the geometry of the coarse grid by an iterative procedure. The geometry of the coarse grid is built so that the variances of flow velocities within the coarse blocks are minimum. Selective upscaling is able to handle complex geological formations and flow patterns, and provides full hydraulic conductivity tensor for each block. Selective upscaling is applied to a cross-bedded formation in which the fine-scale hydraulic conductivities are full tensors with principal directions not parallel to the statistical anisotropy of their spatial distribution. Mass transport results from three coarse-scale models constructed by different upscaling techniques are compared to the fine-scale results for different flow conditions. Selective upscaling provides coarse grids in which mass transport simulation is in good agreement with the fine-scale simulations, and consistently superior to simulations on traditional regular (equal-sized) grids or elastic grids built without accounting for flow velocities. 相似文献
13.
Tai Sasaki Naro Hashimoto Takayuki Nakato Tomonari Shiraishi Kazuaki Yajima Tomoyuki Hishiya 《Engineering Geology》1998,49(3-4):337-343
As a preliminary step for predicting groundwater flow in a plateau 30–50 m above sea level, a model for three-dimensional analysis of groundwater flow was formulated and its validity was verified. The plateau consists of Neogene sedimentary rocks and a Quaternary deposit. Most of the groundwater originates in precipitation, with the groundwater table lying in the Quaternary deposit. Steady-state analysis was conducted by using the finite element method. The results of pore-water pressure measurement and water examination were useful in verifying the validity of the model. In constructing the model, reducing the hydraulic conductivity according to the depth on the basis of the results of the actual measurement was important. 相似文献
14.
Laurence R. Bentley Masaki Hayashi Elena P. Zimmerman Chris Holmden Lynn I. Kelley 《Hydrogeology Journal》2016,24(4):877-892
Hypersaline lakes occur in hydrologically closed basins due to evaporitic enrichment of dissolved salts transported to the lakes by surface water and groundwater. At the hypersaline Lydden Lake in Saskatchewan, Canada, groundwater/lake-water interaction is strongly influenced by the geological heterogeneity of glacial deposits, whereby a highly permeable glaciofluvial sand/gravel deposit is underlain by glaciolacustrine deposits consisting of dense clay interspersed with silt/sand lenses. Pressure head distribution in a near shore area indicates a bi-directional flow system. It consists of topographically driven flow of fresh groundwater towards the lake in the sand/gravel aquifer and density-driven, landward flow of saline groundwater in the underlying glaciolacustrine deposits. Electrical resistivity tomography, and chemical and isotopic composition of groundwater clearly show the landward intrusion of saline water in the heterogeneous unit. The feasibility of bi-directional flow and transport is supported by numerical simulations of density-coupled groundwater flow and transport. The results suggest that the geologically controlled groundwater exchange processes have substantial influences on both inputs and outputs of dissolved minerals in hypersaline lakes in closed basins. 相似文献
15.
16.
Stochastic analysis of the effect of heterogeneity and fractures on radionuclide transport in a low-permeability clay layer 总被引：1，自引：0，他引：1
Deep low-permeability clay layers are considered as safe environments for disposal of high-level radioactive waste. In Belgium,
the Boom Clay is a candidate host rock for deep geological disposal. In this study, we analyze the effects of fractures and
spatially variable hydraulic conductivity on radionuclide migration through the clay. Fracture geometry and properties are
simulated with Monte Carlo simulation. The heterogeneity of hydraulic conductivity is simulated by direct sequential co-simulation
using measurements of hydraulic conductivity and four types of secondary variables. The hydraulic conductivity and fracture
simulations are used as input for a transport model. Radionuclide fluxes computed with this heterogeneous model are compared
with fluxes obtained with a homogeneous model. The output fluxes of the heterogeneous model differ at most 8% from the homogeneous
model. The main safety function of the Boom Clay is thus not affected by the fractures and the spatial variability of hydraulic
conductivity. 相似文献
17.
The movement of chemicals through soil to groundwater is a major cause of degradation of water resources. In many cases, serious human and stock health implications are associated with this form of pollution. The study of the effects of different factors involved in transport phenomena can provide valuable information to find the best remediation approaches. Numerical models are increasingly being used for predicting or analyzing solute transport processes in soils and groundwater. This article presents the development of a stochastic finite element model for the simulation of contaminant transport through soils with the main focus being on the incorporation of the effects of soil heterogeneity in the model. The governing equations of contaminant transport are presented. The mathematical framework and the numerical implementation of the model are described. The comparison of the results obtained from the developed stochastic model with those obtained from a deterministic method and some experimental results shows that the stochastic model is capable of predicting the transport of solutes in unsaturated soil with higher accuracy than deterministic one. The importance of the consideration of the effects of soil heterogeneity on contaminant fate is highlighted through a sensitivity analysis regarding the variance of saturated hydraulic conductivity as an index of soil heterogeneity. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
18.
A design procedure is proposed to minimize water infiltration into landfills by optimizing the water diversion length of inclined
covers with capillary barrier effect (CCBE). This design procedure is based on a conceptual, mathematical and numerical approach
and aims at selecting materials and optimizing layer thickness. Selection among candidate materials is made based on their
hydraulic conductivity functions and on a threshold infiltration rate imposed on the designer. The capillary break layer (CBL;
bottom layer) is characterized by a weak capillarity, while the moisture retention layer (MRL; upper layer) is characterized
by a compromise between strong capillarity and high hydraulic conductivity. The thickness of the CBL corresponds to the height
where suction reaches its maximum value for a given infiltration rate. This height can be calculated using the Kisch [Géotechnique 9 (1959)] model. The optimal thickness of the MRL is determined by applying an adaptation of the Ross [Water Resources Research 26 (1990)] model. The results obtained using the proposed design procedure were compared to those obtained from numerical simulations
performed using a finite element unsaturated seepage software. The procedure was applied for two cover systems; one where
deinking by-products (DBP) were used as MRL and sand as CBL and another where sand was used as MRL and gravel as CBL. Using
this procedure, it has been shown that an infiltration control system composed of thin layers of sand over gravel is highly
efficient in terms of diversion length and that its efficiency can be enhanced by placing a hydraulic barrier – such as a
layer of DBP – above the MRL. 相似文献
19.
Stefan Bachu 《Tectonophysics》1991,190(2-4):299-314
Heterogeneity is present in geological sedimentary structures at all scales from pore to basin, and its distribution has an impact on transport processes such as heat and fluid flow. The rock masses at any scale need to be characterized by their effective properties at that scale, based on the individual characteristics of the heterogeneous porous medium. The effective thermal and hydraulic conductivity of sediments characterized by a stochastic distribution of heterogeneity is studied using an inverse approach based on numerical experiments. The simulations, covering a large range of conductivity contrasts, are carried out for actual core-scale cases of shale clasts in a sand matrix, and on a diagrammatic cross-section through a clastic sedimentary group at the basin scale.
The effective conductivity depends primarily on the heterogeneity fraction and on the conductivity contrast between heterogeneities and the embedding matrix, a dependency which can be described by a generalized weighted mean model. This model is better suited to estimate the effective conductivity at any scale than other models like the self-consistent, or any of the arithmetic, geometric or harmonic averages. The effective conductivity has an anisotropic character although the individual components are homogeneous and isotropic. The variation in effective conductivity is significant even for small conductivity contrasts, like in heat flow processes, and exhibits an asymptotic behaviour for large conductivity contrasts characteristic of fluid flow processes. The effective conductivity has a second-order dependence on such heterogeneity characteristics as shape, aspect ratio, orientation, and distribution. Depending on these characteristics, the bounds of effective conductivity values can be narrowed further from the extreme bounds expressed by the arithmetic and harmonic averages. 相似文献
20.
土-膨润土系竖向隔离墙广泛应用于工业污染场地和地下水修复工程。通过坍落度和一维压缩固结试验研究添加沸石对黏性土-膨润土竖向隔离墙材料的工作性,以及压缩和渗透特性。黏性土选用高岭土,沸石-高岭土-膨润土试样中沸石掺量为2%～40%。试验结果与以往沸石-砂-膨润土竖向隔离墙材料以及击实沸石-膨润土混合土研究结果进行对比,明确沸石掺量和粒径对压缩和渗透特性的作用规律。试验结果显示,满足隔离墙材料施工要求的含水率范围随沸石掺量增加而增大,并处于液限的0.96～1.18倍。添加细颗粒沸石对试样的压缩指数和渗透系数影响较小,渗透系数小于10-9 m/s。相反,添加粗颗粒沸石将导致微孔隙尺寸增大,并形成水能够通过的沸石网架结构,将显著增大渗透系数。试样渗透系数能够通过考虑孔隙比和液限的经验公式进行良好的预测。 相似文献