共查询到20条相似文献，搜索用时 31 毫秒
1.
随着北斗三号卫星导航系统(BeiDou navigation satellite system-3, BDS-3)开始向全球提供导航服务,独立使用BDS为在轨运行的卫星提供全球覆盖、全时段的定位服务成为可能。结合风云三号D星(FengYun-3D, FY-3D)全球卫星导航系统掩星探测仪(global navigation satellite system occultation sounder, GNOS)的真实在轨数据对天基BDS的定位性能进行了详细的分析。首先,使用BDS真实广播星历计算了在不同轨道高度下的可见卫星数和定位精度因子（position dilution of precision, PDOP）,并结合精密星历分析了广播星历的轨道误差、时钟误差及空间信号测距误差(signal-in-space range error, SISRE)。仿真结果表明,在95%的置信水平下,从地面到2 000 km的轨道高度,BDS在全球范围内最小可见卫星数为6,最大PDOP小于5,星座可用性已经达到100%,全球平均可见卫星数BDS比GPS(global positioning syste... 相似文献
2.
3.
Yanming Feng 《GPS Solutions》2001,5(2):1-11
Single-epoch point positioning with the global positioning system (GPS) is as accurate in low orbit as it is on the ground:
typically a three-dimensional rms accuracy of 20 to 30 m as the selective availability turns to zero. This is achieved at
any observation epoch without orbit dynamic information. With sophisticated models and filtering techniques onboard the spacecraft,
the orbit accuracy of a Low Earth Orbiter (LEO) can be improved to a few meters using the civilian broadcast GPS signals.
To achieve this accuracy autonomously in real time, an efficient onboard computing processor is required to carry out the
sophisticated orbit integration and filtering process.
In this paper, a new orbit integrator is presented that computes the nominal orbit states (the position and velocity) and
the state transition equations with numerical methods of integral equation, instead of differential equation usually used
for orbit computation. The algorithm is simple, and can be easily embedded in an onboard processor. The numerical results
demonstrate that the proposed method of the integral equation provides precise orbit predictions over several orbits. The
sequential filter based on the above integrator allows the use of simple orbit state equations to efficiently correct dynamical
model errors with precise GPS measurements or improve the orbits using GPS navigaion solutions from the 3D rms accuracy of
26 m to 3.7 m within a few hours of tracking. ? 2001 John Wiley & Sons, Inc. 相似文献
4.
Due to their low cost and low power consumption, single-frequency GPS receivers are considered suitable for low-cost space applications such as small satellite missions. Recently, requirements have emerged for real-time accurate orbit determination at sub-meter level in order to carry out onboard geocoding of high-resolution imagery, open-loop operation of altimeters and radio occultation. This study proposes an improved real-time kinematic positioning method for LEO satellites using single-frequency receivers. The C/A code and L1 phase are combined to eliminate ionospheric effects. The epoch-differenced carrier phase measurements are utilized to acquire receiver position changes which are further used to smooth the absolute positions. A kinematic Kalman filter is developed to implement kinematic orbit determination. Actual flight data from China’s small satellite SJ-9A are used to test the navigation performance. Results show that the proposed method outperforms traditional kinematic positioning method in terms of accuracy. A 3D position accuracy of 0.72 and 0.79 m has been achieved using the predicted portion of IGS ultra-rapid products and broadcast ephemerides, respectively. 相似文献
5.
Low Earth orbit (LEO) constellations have potentialities to augment global navigation satellite systems for better service performance. The prerequisite is to provide the broadcast ephemerides that meet the accuracy requirement for navigation and positioning. In this study, the Kepler ephemeris model is chosen as the basis of LEO broadcast ephemeris design for backward compatibility and simplicity. To eliminate the singularity caused by the smaller eccentricity of LEO satellites compared to MEO satellites, non-singular elements are introduced for curve fitting of parameters and then transformed to Kepler elements to assure the algorithm of ephemeris computation remains unchanged for the user. We analyze the variation characteristics of LEO orbital elements and establish suitable broadcast ephemeris models considering fit accuracy, number of parameters, fit interval, and orbital altitude. The results of the fit accuracy for different fit intervals and orbital altitudes suggest that the optimal parameter selections are \((Crs3,Crc3)\), \((Crs3,Crc3, \, \dot{a},\dot{n})\) and \(\left( {Crs3,Crc3, \, \dot{a},\dot{n}, \, \ddot{i},\ddot{a}} \right)\), i.e., adding two, four or six parameters to the GPS 16-parameter ephemeris. When adding four parameters, the fit accuracy can be improved by about one order of magnitude compared to the GPS 16-parameter ephemeris model, and fit errors of less than 10 cm can be achieved with 20-min fit interval for a 400–1400 km orbital altitude. In addition, the effects of the number of parameters, fit interval, and orbit altitude on fit accuracy are discussed in detail. The validation with four LEO satellites in orbit also confirms the effectiveness of proposed models. 相似文献
6.
实现低轨导航增强的关键前提是实现低轨星座的整网时间同步,本文针对低轨导航增强系统,提出了一种基于实时精密单点定位(RT-PPP)的低轨卫星高精度时间同步方法,以解决低轨星座实时高精度时间同步的问题. 本文分析了在处理过程中存在的各类误差,介绍了低轨卫星采用状态空间(SSR)改正信息通过精密单点定位(PPP)实现实时高精度时间同步方法的处理流程,将此方法应用于气象、电离层与气候星座观测系统(COSMIC)卫星实测数据的处理,并将该方法与采用广播星历伪距的方法以及事后精密星历的方法进行了比较分析. 结果表明:采用SSR改正信息PPP的方式对2颗COSMIC卫星进行GPS双频观测值的解算,得到的轨道误差的标准差在分米级,钟差误差标准差分别在2.4 ns和2.3 ns左右,可以达到纳秒级. 通过对不同方法解算的结果进行比较可以看出,采用SSR改正信息PPP的方法明显优于采用广播星历伪距方法的解算精度,且与事后精密星历PPP的方法解算精度相当. 相似文献
7.
为了对多个全球导航卫星系统（global navigation satellite system, GNSS）当前的广播星历精度进行一个全面的分析,对比了2014—2018年共5 a的GNSS广播星历与精密星历,并对全球定位系统（global positioning system, GPS）、格洛纳斯卫星导航系统（global navigation satellite system, GLONASS）、伽利略卫星导航系统（Galileo satellite navigation system, Galileo）、北斗卫星导航系统（BeiDou navigation satellite system, BDS）、准天顶卫星系统（quasi-zenith satellite system, QZSS）等5个系统的广播星历长期精度变化进行了分析。结果表明:5 a中GPS的广播星历轨道及钟差精度最稳定;GLONASS的广播星历轨道精度稳定性较好,但其钟差精度存在较大的离散度;Galileo得益于具备全面运行能力（full operational capability, FOC）卫星的大量发射及运行,其广播星历轨道、钟差精度大幅度变好,切向轨道、法向轨道与钟差精度已赶超GPS;BDS的广播星历轨道精度离散度较大,钟差精度出现不稳定现象;QZSS的广播星历轨道与钟差精度的稳定性与离散度相对最差。以2018年1 a的广播星历与精密星历为例分析了各个系统当前的广播星历精度,结果表明,当前GPS、GLONASS、Galileo、BDS、QZSS的考虑轨道误差与钟差误差贡献的空间信号测距误差（signal-in-space ranging error,SISRE）分别为0.806 m、2.704 m、0.320 m、1.457 m、1.645 m,表明Galileo广播星历整体精度最高,GPS次之,其次分别是BDS、QZSS和GLONASS。只考虑轨道误差贡献的SISRE分别为0.167 m、0.541 m、0.229 m、0.804 m、0.675 m,表明GPS广播星历轨道精度最高,其次分别是Galileo、GLONASS、QZSS和BDS。GPS卫星广播星历中新型号卫星的钟差精度总体要优于旧型号卫星。 相似文献
8.
目前各类用户对基于北斗卫星导航定位服务需求在不断扩大,由于广播星历实时、易获取,北斗广播星历精度是实时导航定位用户关心的问题,也是检验系统是否达成设计指标的关键因素。文中基于国家基准站和MGEX站计算北斗精密轨道,重复弧段精度优于利用国际站计算结果。将计算的北斗精密轨道作为参考,更加准确地评估分析北斗广播星历轨道误差的精度。分析结果显示,北斗广播星历轨道径向精度优于法向和切向精度,且法向误差具有较为明显的周期性。各类卫星中,GEO卫星精度稍差,而IGSO和MEO卫星与GPS在同一量级。随着北斗卫星系统逐步组网完善,地面监测站分布趋于合理,北斗系统整体性能将会不断提高。 相似文献
9.
Recent studies have demonstrated the usefulness of global positioning system (GPS) receivers for relative positioning of formation-flying satellites using dual-frequency carrier-phase observations. The accurate determination of distances or baselines between satellites flying in formation can provide significant benefits to a wide area of geodetic studies. For spaceborne radar interferometry in particular, such measurements will improve the accuracy of interferometric products such as digital elevation models (DEM) or surface deformation maps. The aim of this study is to analyze the impact of relative position errors on the interferometric baseline performance of multistatic synthetic aperture radar (SAR) satellites flying in such a formation. Based on accuracy results obtained from differential GPS (DGPS) observations between the twin gravity recovery and climate experiment (GRACE) satellites, baseline uncertainties are derived for three interferometric scenarios of a dedicated SAR mission. For cross-track interferometry in a bistatic operational mode, a mean 2D baseline error (1σ) of 1.4 mm is derived, whereas baseline estimates necessary for a monostatic acquisition mode with a 50 km along-track separation reveal a 2D uncertainty of approximately 1.7 mm. Absolute orbit solutions based on reduced dynamic orbit determination techniques using GRACE GPS code and carrier-phase data allows a repeat-pass baseline estimation with an accuracy down to 4 cm (2D 1σ). To assess the accuracy with respect to quality requirements of high-resolution DEMs, topographic height errors are derived from the estimated baseline uncertainties. Taking the monostatic pursuit flight configuration as the worst case for baseline performance, the analysis reveals that the induced low-frequency modulation (height bias) fulfills the relative vertical accuracy requirement (σ<1 m linear point-to-point error) according to the digital terrain elevation data level 3 (DTED-3) specifications for most of the baseline constellations. The use of a GPS-based reduced dynamic orbit determination technique improves the baseline performance for repeat-pass interferometry. The problem of fulfilling the DTED-3 horizontal accuracy requirements is still an issue to be investigated. DGPS can be used as an operational navigation tool for high-precision baseline estimation if a geodetic-grade dual-frequency spaceborne GPS receiver is assumed to be the primary instrument onboard the SAR satellites. The possibility of using only single-frequency receivers, however, requires further research effort.Deutsche Forschungsgemeinschaft (DFG) research fellow until Sept. 2004 at the Microwaves and Radar Institute, Deutsche Zentrum für Luft- und Raumfahrt (DLR) e.V., 82234 Weßling, Germany 相似文献
10.
Oliver Montenbruck Miquel Garcia-Fernandez Yoke Yoon Steffen Schön Adrian Jäggi 《GPS Solutions》2009,13(1):23-34
Phase center variations of the receiver and transmitter antenna constitute a remaining uncertainty in the high precision orbit
determination (POD) of low Earth orbit (LEO) satellites using GPS measurements. Triggered by the adoption of absolute phase
patterns in the IGS processing standards, a calibration of the Sensor Systems S67-1575-14 antenna with GFZ choke ring has
been conducted that serves as POD antenna on various geodetic satellites such as CHAMP, GRACE and TerraSAR-X. Nominal phase
patterns have been obtained with a robotic measurement system in a field campaign and the results were used to assess the
impact of receiver antenna phase patterns on the achievable positioning accuracy. Along with this, phase center distortions
in the actual spacecraft environment were characterized based on POD carrier phase residuals for the GRACE and TerraSAR-X
missions. It is shown that the combined ground and in-flight calibration can improve the carrier phase modeling accuracy to
a level of 4 mm which is close to the pure receiver noise. A 3.5 cm (3D rms) consistency of kinematic and reduced dynamic
orbit determination solutions is achieved for TerraSAR-X, which presumably reflects the limitations of presently available
GPS ephemeris products. The reduced dynamic solutions themselves match the observations of high grade satellite laser ranging
stations to 1.5 cm but are potentially affected by cross-track biases at the cm-level. With respect to the GPS based relative
navigation of TerraSAR-X/TanDEM-X formation, the in-flight calibration of the antenna phase patterns is considered essential
for an accurate modeling of differential carrier phase measurements and a mm level baseline reconstruction.
相似文献
| Oliver MontenbruckEmail: |
11.
Precision spacecraft navigation using a low-cost GPS receiver 总被引：1，自引：1，他引：0
Oliver Montenbruck Paul Swatschina Markus Markgraf Stefano Santandrea Joris Naudet Etienne Tilmans 《GPS Solutions》2012,16(4):519-529
Within the PROBA-2 microsatellite mission, a miniaturized single-frequency GPS receiver based on commercial-off-the-shelf (COTS) technology is employed for onboard navigation and timing. A rapid electronic fuse protects against destructive single-event latch-ups (SEL) and enables a quasi-continuous receiver operation despite the inherent sensitivity to space radiation. While limited to single-frequency C/A-code tracking with a narrow-band frontend, the receiver is able to provide precision navigation services through processing of raw GPS measurements on ground as well as a built-in real-time navigation system. In both cases, ionospheric path delays are eliminated through a combination of L1 pseudorange and carrier phase measurements, which also offers a factor-of-two noise reduction relative to code-only processing. By comparison with satellite laser ranging (SLR) measurements, a 0.3-m (3D rms) accuracy is demonstrated for the PROBA-2 reduced dynamic orbit determinations using post-processed GPS orbit and clock products. Furthermore, the experimental onboard navigation system is shown to provide real-time position information with a 3D rms accuracy of about 1?m, which notably outperforms the specification of the Standard Positioning Service (SPS). In view of their lower hardware complexity, mass budget and power requirements as well as the reduced interference susceptibility, legacy C/A-code receivers can thus provide an attractive alternative to dual-frequency receivers even for demanding navigation applications in low Earth orbit. 相似文献
12.
现阶段高轨道航天器导航主要依靠地基测控系统,为了研究全球卫星导航系统(GNSS)技术用于高轨道航天器导航的可行性,对GNSS技术在地球静止轨道(GEO)卫星、倾斜地球同步轨道(IGSO)卫星航天器中的导航精度及适用性展开了分析研究. 采用2021年11月9日的两行轨道数据(TLE)仿真GNSS星座,以不同星下点的GEO卫星和不同倾角的IGSO卫星作为目标星展开导航仿真试验. 实验结果表明:为了满足GNSS解算所需的卫星数量,须通过接收旁瓣信号来增加可见卫星数目. 对GEO目标星而言,当接收机灵敏度高于?169 dB时,导航精度可达30 m;利用GPS对7个不同的GEO或IGSO轨道目标星进行导航实验表明,GPS对目标星导航的位置误差约为35 m;北斗三号(BDS-3)、GPS、GLONASS、Galileo的导航位置误差均值分别为28.03 m、21.16 m、37.15 m、25.09 m,具有良好的内符合精度,其中GPS精度最高,GLONASS精度最低,但大部分时段也在45 m内. 相似文献
13.
针对系统地评估我国北斗卫星导航系统广播星历精度与保障实时导航定位服务的需求,对BDS广播星历提供的卫星轨道、钟差以及用户测距误差(URE)的精度性能进行分析,统计了2015年连续4周全部BDS在轨健康卫星的广播星历各项精度指标值。分析结果表明:BDS的MEO和IGSO卫星轨道精度优于GEO卫星结果,且径向精度优于法向和切向精度;BDS搭载的国产星载铷钟卫星钟差序列相对比较稳定,其均方根误差优于4ns;GEO/IGSO卫星的用户距离误差(URE)在6m以内,MEO的URE优于20m。研究结果对北斗系统的建设、后期的发展和用户市场的拓展,都具有重要的参考价值。 相似文献
14.
15.
This report provides a detailed performance analysis of three semicodeless dual-frequency GPS receivers for use in low Earth orbit (LEO). The test set comprises the IGOR receiver, which represents a follow-on of the flight-proven BlackJack receiver, as well as two geodetic receivers (NovAtel OEM4-G2 and Septentrio PolaRx2), which are entirely based on commercial-off-the-shelf technology (COTS). All three receivers are considered for upcoming flight projects or experiments and have undergone at least a preliminary environmental qualification program. Using extensive signal simulator tests, the cold start signal acquisition, tracking sensitivity, differential code biases, raw measurement accuracy, and navigation accuracy of each receiver have been assessed. All tests are based on a common scenario that is representative of an actual space mission and provides a realistic simulation of the signal dynamics and quality on a scientific LEO satellite. Compared to the other receivers, the IGOR instrument exhibits a superior tracking sensitivity and is thus best suited for occultation measurements with low tangent point altitudes. The OEM4-G2 and PolaRx2 receivers are likewise shown to properly track dual-frequency GPS signals and normal signal levels and to provide accurate code and carrier phase measurements. Given their limited resource requirements, these receivers appear well suited for precise orbit determination applications and ionospheric sounding onboard of microsatellites with tight mission budgets. 相似文献
16.
Single receiver phase ambiguity resolution with GPS data 总被引：26，自引：12，他引：14
Willy Bertiger Shailen D. Desai Bruce Haines Nate Harvey Angelyn W. Moore Susan Owen Jan P. Weiss 《Journal of Geodesy》2010,84(5):327-337
Global positioning system (GPS) data processing algorithms typically improve positioning solution accuracy by fixing double-differenced
phase bias ambiguities to integer values. These “double-difference ambiguity resolution” methods usually invoke linear combinations
of GPS carrier phase bias estimates from pairs of transmitters and pairs of receivers, and traditionally require simultaneous
measurements from at least two receivers. However, many GPS users point position a single local receiver, based on publicly
available solutions for GPS orbits and clocks. These users cannot form double differences. We present an ambiguity resolution
algorithm that improves solution accuracy for single receiver point-positioning users. The algorithm processes dual- frequency
GPS data from a single receiver together with wide-lane and phase bias estimates from the global network of GPS receivers
that were used to generate the orbit and clock solutions for the GPS satellites. We constrain (rather than fix) linear combinations
of local phase biases to improve compatibility with global phase bias estimates. For this precise point positioning, no other
receiver data are required. When tested, our algorithm significantly improved repeatability of daily estimates of ground receiver
positions, most notably in the east component by approximately 30% with respect to the nominal case wherein the carrier biases
are estimated as real values. In this “static” test for terrestrial receiver positions, we achieved daily repeatability of
1.9, 2.1 and 6.0 mm in the east, north and vertical (ENV) components, respectively. For kinematic solutions, ENV repeatability
is 7.7, 8.4, and 11.7 mm, respectively, representing improvements of 22, 8, and 14% with respect to the nominal. Results from
precise orbit determination of the twin GRACE satellites demonstrated that the inter-satellite baseline accuracy improved
by a factor of three, from 6 to 2 mm up to a long-term bias. Jason-2/Ocean Surface Topography Mission precise orbit determination
tests results implied radial orbit accuracy significantly below the 10 mm level. Stability of time transfer, in low-Earth
orbit, improved from 40 to 7 ps. We produced these results by applying this algorithm within the Jet Propulsion Laboratory’s
(JPL’s) GIPSY/OASIS software package and using JPL’s orbit and clock products for the GPS constellation. These products now
include a record of the wide-lane and phase bias estimates from the underlying global network of GPS stations. This implies
that all GIPSY–OASIS positioning users can now benefit from this capability to perform single-receiver ambiguity resolution. 相似文献
17.
Different types of GPS clock and orbit data provided by the International GPS Service (IGS) have been used to assess the accuracy
of rapid orbit determination for satellites in low Earth orbit (LEO) using spaceborne GPS measurements. To avoid the need
for reference measurements from ground-based reference receivers, the analysis is based on an undifferenced processing of
GPS code and carrier-phase measurements. Special attention is therefore given to the quality of GPS clock data that directly
affects the resulting orbit determination accuracy. Interpolation of clock data from the available 15 min grid points is identified
as a limiting factor in the use of IGS ultra-rapid ephemerides. Despite this restriction, a 10-cm orbit determination accuracy
can be obtained with these products data as demonstrated for the GRACE-B spacecraft during selected data arcs between 2002
and 2004. This performance may be compared with a 5-cm orbit determination accuracy achievable with IGS rapid and final products
using 5 min clock samples. For improved accuracy, high-rate (30 s) clock solutions are recommended that are presently only
available from individual IGS centers. Likewise, a reduced latency and more frequent updates of IGS ultra-rapid ephemerides
are desirable to meet the requirements of upcoming satellite missions for near real-time and precise orbit determination. 相似文献
18.
Cheinway Hwang Tzu-Pang Tseng Tingjung Lin Dražen Švehla Bill Schreiner 《Journal of Geodesy》2009,83(5):477-489
The joint Taiwan–US mission FORMOSAT-3/ COSMIC (COSMIC) was launched on April 17, 2006. Each of the six satellites is equipped
with two POD antennas. The orbits of the six satellites are determined from GPS data using zero-difference carrier-phase measurements
by the reduced dynamic and kinematic methods. The effects of satellite center of mass (COM) variation, satellite attitude,
GPS antenna phase center variation (PCV), and cable delay difference on the COSMIC orbit determination are studied. Nominal
attitudes estimated from satellite state vectors deliver a better orbit accuracy when compared to observed attitude. Numerical
tests show that the COSMIC COM must be precisely calibrated in order not to corrupt orbit determination. Based on the analyses
of the 5 and 6-h orbit overlaps of two 30-h arcs, orbit accuracies from the reduced dynamic and kinematic solutions are nearly
identical and are at the 2–3 cm level. The mean RMS difference between the orbits from this paper and those from UCAR (near
real-time) and WHU (post-processed) is about 10 cm, which is largely due to different uses of GPS ephemerides, high-rate GPS
clocks and force models. The kinematic orbits of COSMIC are expected to be used for recovery of temporal variations in the
gravity field. 相似文献
19.
针对GPS、GLONASS、BDS组合定位中观测值定权的问题,利用广播星历计算卫星位置,以IGS提供的精密星历为参考,将卫星坐标的三维均方根误差与附有加权因子的用户等效距离误差作为精度指标,对各系统轨道误差进行对比分析,找寻其规律。对2013、2014、2015各年8月份轨道误差进行分析,结果表明BDS系统在逐步完善,GPS/GLONASS/BDS 3系统轨道误差的权比在3年间显示出5∶2∶1、5∶2∶2、5∶2∶3的变化。以后的组合定位观测值可参考2015年的权比定权。 相似文献
20.
Cheinway Hwang Tzu-Pang Tseng Ting-Jung Lin Dražen Švehla Urs Hugentobler Benjamin Fong Chao 《GPS Solutions》2010,14(1):121-131
The precise orbit determination antennas of F3/C and GRACE-A satellites are from the same manufacturer, but are installed
in different configurations. The current orbit accuracy of F3/C is 3 cm at arcs with good GPS data, compared to 1 cm of GRACE,
which has a larger ratio of usable GPS data. This paper compares the qualities of GPS observables from F3/C and GRACE. Using
selected satellites and time spans, the following average values for the satellite F3/C and satellite A of GRACE are obtained:
multipath effect on the pseudorange P1, 0.78 and 0.38 m; multipath effect on the pseudorange P2, 1.03 and 0.69 m; occurrence
frequency of cycle slip, 1/29 and 1/84; standard error of unit weight, 4 and 1 cm; dynamic–kinematic orbit difference, 10
and 2 cm. For gravity determination using F3/C GPS data, a careful selection of GPS data is critical. With six satellites
in orbit, F3/C’s large amount of GPS data will make up the deficiency in data quality. 相似文献