首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
A small-scale hydrogeological study was conducted in a fractured carbonate-rock aquifer located in a quarry to relate groundwater flow to the fracture network. The field study in the St-Eustache quarry, which integrates structural surveys, well logging and hydraulic tests, showed that the most important features that affect groundwater flow in the sedimentary aquifer are high hydraulic conductivity horizontal bedding planes. Vertical fractures are abundant in the quarry and throughout the region, but they have a minor effect on groundwater flow. To have a significant impact on the flow regime and lead to vertical groundwater flow, the permeability of all vertical joints need to be enhanced compared to what was generally observed at the site. Such an increase in permeability could potentially occur where dissolution and fracturing is more intense or at stress release locations such as near the surface in the quarry.  相似文献   

2.
Contamination of the Paleozoic carbonate aquifer at Walkerton (Ontario, Canada) by pathogenic bacteria following heavy rain in May 2000 resulted in 2,300 illnesses and seven deaths. Subsequent tracer testing showed that there was rapid groundwater flow in the aquifer, and also rapid exchange between the aquifer and the ground surface. Electrical conductivity (EC) profiling during a 3-day pumping test showed that most flow was through bedding-plane fractures spaced about 10 m apart, that there were substantial contrasts in EC in the major fracture flows, and that there were rapid changes over time. Total coliform sampling revealed transient groundwater contamination, particularly after heavy rain and lasting up to a few days. These characteristics can be understood in terms of the dual-porosity nature of the aquifer. Most of the storage is in the matrix, but this can be considered to be static in the short term. Almost all transport is through the fracture network, which has rapid groundwater flow (～100 m/day) and rapid transmission of pressure pulses due to the high hydraulic diffusivity. Rapid recharge can occur through thin and/or fractured overburden and at spring sites where flow is reversed by pumping during episodes of surface flooding. These characteristics facilitated the ingress of surface-derived bacteria into the aquifer, and their rapid transport within the aquifer to pumping wells. Bacterial presence is common in carbonate aquifers, and this can be explained by the well-connected, large-aperture fracture networks in these dual-porosity aquifers, even though many, such as at Walkerton, lack karst landforms.  相似文献   

3.
Groundwater for domestic and irrigation purposes is produced primarily from shallow parts of the Bengal Basin aquifer system (India and Bangladesh), which contains high concentrations of dissolved arsenic (exceeding worldwide drinking water standards), though deeper groundwater is generally low in arsenic. An essential first step for determining sustainable management of the deep groundwater resource is identification of hydrogeologic controls on flow and quantification of basin-scale groundwater flow patterns. Results from groundwater modeling, in which the Bengal Basin aquifer system is represented as a single aquifer with higher horizontal than vertical hydraulic conductivity, indicate that this anisotropy is the primary hydrogeologic control on the natural flowpath lengths. Despite extremely low hydraulic gradients due to minimal topographic relief, anisotropy implies large-scale (tens to hundreds of kilometers) flow at depth. Other hydrogeologic factors, including lateral and vertical changes in hydraulic conductivity, have minor effects on overall flow patterns. However, because natural hydraulic gradients are low, the impact of pumping on groundwater flow is overwhelming; modeling indicates that pumping has substantially changed the shallow groundwater budget and flowpaths from predevelopment conditions.  相似文献   

4.
Fractured-rock aquifers display spatially and temporally variable hydraulic conductivity generally attributed to variable fracture intensity and connectivity. Empirical evidence suggests fracture aperture and hydraulic conductivity are sensitive to in situ stress. This study investigates the sensitivity of fractured-rock hydraulic conductivity, groundwater flow paths, and advection-dominated transport to variable shear and normal fracture stiffness magnitudes for a range of deviatoric stress states. Fracture aperture and hydraulic conductivity are solved for analytically using empirical hydromechanical coupling equations; groundwater flow paths and ages are then solved for numerically using groundwater flow and advection-dispersion equations in a traditional Toth basin. Results suggest hydraulic conductivity alteration is dominated by fracture normal closure, resulting in decreasing hydraulic conductivity and increasing groundwater age with depth, and decreased depth of long flow paths with decreasing normal stiffness. Shear dilation has minimal effect on hydraulic conductivity alteration for stress states investigated here. Results are interpreted to suggest that fracture normal stiffness influences hydraulic conductivity of hydraulically active fractures and, thus, affects flow and transport in shallow (<1 km) fractured-rock aquifers. It is suggested that observed depth-dependent hydraulic conductivity trends in fractured-rock aquifers throughout the world may be partly a manifestation of hydromechanical phenomena.  相似文献   

5.
Pump tests and geophysical logs acquired in a fluvial sandstone aquifer within the resource-rich Moncton Subbasin of New Brunswick, Canada, have been used to characterize fracture patterns and flow directions for purposes of developing a water-wellfield protection plan. Fracture patterns consist of three high-angle sets, and a low-angle set parallel to bedding. NW-trending high-angle fractures, predominantly in fluvial sandstone units, appear to be most important in controlling groundwater flow directions. This contrasts with an earlier regional hydrogeological study that attributed most flow to sub-horizontal bedding-plane fractures. Water levels monitored during a 72-h pump test revealed drawdown extension parallel to the NW-trending fracture set. Drawdown curves indicate that the aquifer is laterally constrained—likely reflecting differences in fracturing observed between the channelized sandstone and surrounding shale units. As a result, groundwater flow induced by pumping is influenced by both fracture anisotropy and by the heterogeneity of the fluvial depositional environment. Relationships observed between fracture patterns, regional geological structure and lithology provide a basis for extrapolating the conceptual model to other nearby areas in the region, where potential impacts of geological resource development on groundwater are attracting public concern.  相似文献   

6.
A hydrogeologic conceptual model that improves understanding of variability in aquitard integrity is presented for a fractured sedimentary bedrock unit in the Cambrian-Ordovician aquifer system of midcontinent North America. The model is derived from multiple studies on the siliciclastic St. Lawrence Formation and adjacent strata across a range of scales and geologic conditions. These studies employed multidisciplinary techniques including borehole flowmeter logging, high-resolution depth-discrete multilevel well monitoring, fracture stratigraphy, fluorescent dye tracing, and three-dimensional (3D) distribution of anthropogenic tracers regionally. The paper documents a bulk aquitard that is highly anisotropic because of poor connectivity of vertical fractures across matrix with low permeability, but with ubiquitous bed parallel partings. The partings provide high bulk horizontal hydraulic conductivity, analogous to aquifers in the system, while multiple preferential termination horizons of vertical fractures serve as discrete low vertical hydraulic conductivity intervals inhibiting vertical flow. The aquitard has substantial variability in its ability to protect underlying groundwater from contamination. Across widespread areas where the aquitard is deeply buried by younger bedrock, preferential termination horizons provide for high aquitard integrity (i.e. protection). Protection is diminished close to incised valleys where stress release and weathering has enhanced secondary pore development, including better connection of fractures across these horizons. These conditions, along with higher hydraulic head gradients in the same areas and more complex 3D flow where the aquitard is variably incised, allow for more substantial transport to deeper aquifers. The conceptual model likely applies to other fractured sedimentary bedrock aquitards within and outside of this region.  相似文献   

7.
This study investigates the hydraulic conductivity field and the groundwater flow pattern as predicted by a calibrated steady state groundwater flow model for the Keta Strip, southeastern Ghana. The hydraulic conductivity field is an important parameter in evaluating aquifer properties in space, and in general basin-wide groundwater resources evaluation and management. This study finds that the general hydraulic conductivity of the unconsolidated unconfined aquifer system of the Keta Strip ranges between 2 m/d and 20 m/d, with an average of 15 m/d. The spatial variation in horizontal hydraulic conductivity appears to take the trend in the variations in the nature of the material in space. Calibrated groundwater recharge suggests that 6.9–34% of annual precipitation recharges the shallow aquifer system. This amount of recharge is significant and suggests high fortunes in terms of groundwater resources development for agriculture and industrial activities in the area. A spatial distribution of groundwater recharge from precipitation is presented in this study. The spatial pattern appears to take the form of the distribution in horizontal hydraulic conductivity, and suggests that the vertical hydraulic conductivity takes the same pattern of spatial variation as the horizontal hydraulic conductivity. This is consistent with observations in other areas. The resulting groundwater flow is dominated by local flow systems as the unconfined system is quite shallow. A general northeast – southwest flow pattern has been observed in the study area.  相似文献   

8.
Quantitative evaluation of management strategies for long-term supply of safe groundwater for drinking from the Bengal Basin aquifer (India and Bangladesh) requires estimation of the large-scale hydrogeologic properties that control flow. The Basin consists of a stratified, heterogeneous sequence of sediments with aquitards that may separate aquifers locally, but evidence does not support existence of regional confining units. Considered at a large scale, the Basin may be aptly described as a single aquifer with higher horizontal than vertical hydraulic conductivity. Though data are sparse, estimation of regional-scale aquifer properties is possible from three existing data types: hydraulic heads, 14C concentrations, and driller logs. Estimation is carried out with inverse groundwater modeling using measured heads, by model calibration using estimated water ages based on 14C, and by statistical analysis of driller logs. Similar estimates of hydraulic conductivities result from all three data types; a resulting typical value of vertical anisotropy (ratio of horizontal to vertical conductivity) is 104. The vertical anisotropy estimate is supported by simulation of flow through geostatistical fields consistent with driller log data. The high estimated value of vertical anisotropy in hydraulic conductivity indicates that even disconnected aquitards, if numerous, can strongly control the equivalent hydraulic parameters of an aquifer system.  相似文献   

9.
This study integrated surface and subsurface stratigraphic data with geophysical logs and hydrogeologic data in order to characterize the hydraulic properties of the Silurian dolomite in northeastern Wisconsin. Silurian stratigraphy consists of predictable alternations of characteristic facies associations. A vertical profile of hydraulic conductivity, obtained from short-interval packer tests in a core hole that penetrates a majority of the Silurian section, indicates that hydraulic conductivity ranges over five orders of magnitude (10–1 to 10–6 cm/s). Matrix conductivity is generally low and varies with texture; the finer-grained restricted-marine and transitional facies being less permeable than the coarser-grained open-marine facies. High-conductivity values are generally associated with bedding-plane fractures, and fracture frequency is greater in the restricted-marine facies. High-flow features in 16 wells were identified using fluid-temperature/resistivity and heat-pulse flowmeter logs. Natural-gamma logs were used to identify the stratigraphic position of flow features in each well and to correlate flow features to specific stratigraphic horizons. By combining stratigraphic, geophysical, and hydrogeologic data, 14 high-permeability zones within the Silurian aquifer have been identified and correlated in wells more than 16 km apart. These zones parallel bedding, appear most pronounced at contacts between contrasting lithologies, and are most abundant in restricted-marine lithologies. Electronic Publication  相似文献   

10.
Karst systems show high spatial variability of hydraulic parameters over small distances and this makes their modeling a difficult task with several uncertainties. Interconnections of fractures have a major role on the transport of groundwater, but many of the stochastic methods in use do not have the capability to reproduce these complex structures. A methodology is presented for the quantification of tortuosity using the single normal equation simulation (SNESIM) algorithm and a groundwater flow model. A training image was produced based on the statistical parameters of fractures and then used in the simulation process. The SNESIM algorithm was used to generate 75 realizations of the four classes of fractures in a karst aquifer in Iran. The results from six dye tracing tests were used to assign hydraulic conductivity values to each class of fractures. In the next step, the MODFLOW-CFP and MODPATH codes were consecutively implemented to compute the groundwater flow paths. The 9,000 flow paths obtained from the MODPATH code were further analyzed to calculate the tortuosity factor. Finally, the hydraulic conductivity values calculated from the dye tracing experiments were refined using the actual flow paths of groundwater. The key outcomes of this research are: (1) a methodology for the quantification of tortuosity; (2) hydraulic conductivities, that are incorrectly estimated (biased low) with empirical equations that assume Darcian (laminar) flow with parallel rather than tortuous streamlines; and (3) an understanding of the scale-dependence and non-normal distributions of tortuosity.  相似文献   

11.
岩体裂隙系统渗流场与应力场耦合模型   总被引：15，自引：0，他引：15  
岩体系统具有复杂的结构。一般认为，岩体系统是非均质各向异性不连续的多相介质体系。当岩体以裂隙为主，且其分布较密集时，可将岩体系统看作等效连续多相介质体系。本文运用等效连续介质理论，提出了两种岩体裂隙系统渗流场与应力场耦合模型：一是以渗透水压力与隙变形关系、应力与渗透系统数关系为基础，建立渗透系数张量计算公式，进而建立等效效连续介质渗流为数学模型。以裂隙岩体应变张量分析为基础，建立裂隙岩体效应力张量  相似文献   

12.
The present work deals with the groundwater aquifer of the Lower Cretaceous sandstone and its sustainable development in Sinai. The studied aquifer system is the most promising groundwater system in Sinai due to its wide extension, hug storage, and good quality. The objective of this paper aims to elucidate the hydrogeological characteristics of the Lower Cretaceous aquifer. The aquifer system occurs under confined conditions. The top surface of the Lower Cretaceous dips steeply towards the southwest direction with step faults. The average sand percent of the penetrated aquifer attains 54%. The main direction of groundwater flow is generally from southwest and locally is concentric to the center of study area related to the influence of the graben block. The aquifer has a hydraulic gradient generally reaches 0.0011 m/m and attains 0.0028 in central portion of study area. The aquifer parameters (effective porosity, transmissivity, and hydraulic conductivity) increase towards the northeast direction with increasing of the sand percentage. Durov diagram plot revealed that the groundwater has been a final stage evolution represented by a NaCl water type. The groundwater salinity increases towards the central of study area coinciding with groundwater flow. The groundwater salinity of the Lower Cretaceous aquifer is brackish water and varies from 2,510 to 5,256 ppm and unsuitable for drinking and domestic purposes.  相似文献   

13.
Large-scale geological features have been identified by satellite imagery and global positioning system data in the Wajid Sandstone in Saudi Arabia. The main objective is to evaluate the importance of fractures for the overall flow behaviour in this fractured rock aquifer and to estimate in-situ hydraulic apertures. Data on fractures and lineaments were available for three outcrops. By applying a “cut-out” routine on the fracture endpoint data of these fracture trace windows, three deterministic discrete fracture networks (DFN), with an area of 100 m?×?100 m, could be generated. These were used to simulate the fracture flow and to determine the hydraulic conductivity tensors. Using additional data on hydraulic pumping tests and matrix conductivities, in-situ hydraulic apertures could be determined. Average in-situ hydraulic apertures range from 1,300 to 1,700 µm. Observations from the field support these results. In addition, a hydraulic conductivity ratio between the matrix and fracture system was used to identify the contribution of the DFN to the overall fluid transport. A ratio of 10.4 was determined, which indicates that the effective flow behaviour in the Wajid Sandstone aquifer is not entirely dominated by the fracture system, though evidently strongly controlled by it.  相似文献   

14.
In an aquifer, heterogeneity plays an important role in governing groundwater flow. Hence, aquifer characterization should involve both the pattern and values of the hydrogeological parameters. A new analytical solution describing the one-dimensional groundwater flow in a multi-zone unconfined aquifer is presented, and a methodology developed from the analytical solution and a heuristic approach for determining the pattern and values of the aquifer parameters are proposed. The analytical solution demonstrates that the hydraulic head varies spatially and is influenced by aquifer heterogeneity. Simulated annealing, a heuristic approach, is incorporated with the solution to simultaneously identify the pattern and values of the hydraulic conductivity for a horizontal multi-zone unconfined aquifer. This approach may be used to give an approximate result for a two-dimensional problem by dividing the model area into a number of transects along the transverse direction, identifying the parameter values along the longitudinal direction for each transect, and then smoothing the identified results.  相似文献   

15.
This paper describes the properties of faults and fractures in the Upper Cretaceous Chatsworth Formation exposed at Santa Susana Field Laboratory and its surroundings (Simi Hills, California), where groundwater flow and contamination have been studied for over three decades.The complex depositional architecture of this turbidite consisting of alternating sandstones and shales, interacting with formative stress conditions are responsible for multi-scale fault hierarchies and permeable fractures in which nearly all groundwater flow occurs.Intensity and distribution of background fractures and their relation to bedding thickness are established for sandstones, the dominant lithology. The architecture of faults with increasing displacement is described, and relationships among fault dimensional parameters captured.Data from ∼400 boreholes and piezometers reveal the effect of faults and fractures on groundwater flow. Large hydraulic head differences, observed across fault zones with shale-rich cores, indicate these structures as cross-flow barriers. Moreover, hydraulic head profiles under ambient conditions, and pumping tests suggest strong hydraulic connectivity in all directions to depth of hundreds of meters.This outcrop-based structural characterization relates the horizontal hydraulic conductivity to the observed well-connected fracture network, and explains the strong vertical connectivity across low-hydraulic conductivity shales as faults and sheared fractures provide flow pathways.  相似文献   

16.
Modern geostatistical techniques allow the generation of high-resolution heterogeneous models of hydraulic conductivity containing millions to billions of cells. Selective upscaling is a numerical approach for the change of scale of fine-scale hydraulic conductivity models into coarser scale models that are suitable for numerical simulations of groundwater flow and mass transport. Selective upscaling uses an elastic gridding technique to selectively determine the geometry of the coarse grid by an iterative procedure. The geometry of the coarse grid is built so that the variances of flow velocities within the coarse blocks are minimum. Selective upscaling is able to handle complex geological formations and flow patterns, and provides full hydraulic conductivity tensor for each block. Selective upscaling is applied to a cross-bedded formation in which the fine-scale hydraulic conductivities are full tensors with principal directions not parallel to the statistical anisotropy of their spatial distribution. Mass transport results from three coarse-scale models constructed by different upscaling techniques are compared to the fine-scale results for different flow conditions. Selective upscaling provides coarse grids in which mass transport simulation is in good agreement with the fine-scale simulations, and consistently superior to simulations on traditional regular (equal-sized) grids or elastic grids built without accounting for flow velocities.  相似文献   

17.
Sedimentological processes often result in complex three-dimensional subsurface heterogeneity of hydrogeological parameter values. Variogram-based stochastic approaches are often not able to describe heterogeneity in such complex geological environments. This work shows how multiple-point geostatistics can be applied in a realistic hydrogeological application to determine the impact of complex geological heterogeneity on groundwater flow and transport. The approach is applied to a real aquifer in Belgium that exhibits a complex sedimentary heterogeneity and anisotropy. A training image is constructed based on geological and hydrogeological field data. Multiple-point statistics are borrowed from this training image to simulate hydrofacies occurrence, while intrafacies permeability variability is simulated using conventional variogram-based geostatistical methods. The simulated hydraulic conductivity realizations are used as input to a groundwater flow and transport model to investigate the effect of small-scale sedimentary heterogeneity on contaminant plume migration. Results show that small-scale sedimentary heterogeneity has a significant effect on contaminant transport in the studied aquifer. The uncertainty on the spatial facies distribution and intrafacies hydraulic conductivity distribution results in a significant uncertainty on the calculated concentration distribution. Comparison with standard variogram-based techniques shows that multiple-point geostatistics allow better reproduction of irregularly shaped low-permeability clay drapes that influence solute transport.  相似文献   

18.
 The coastal aquifer system of southern Oahu, Hawaii, USA, consists of highly permeable volcanic aquifers overlain by weathered volcanic rocks and interbedded marine and terrestrial sediments of both high and low permeability. The weathered volcanic rocks and sediments are collectively known as caprock, because they impede the free discharge of groundwater from the underlying volcanic aquifers. A cross-sectional groundwater flow and transport model was used to evaluate the hydrogeologic controls on the regional flow system in southwestern Oahu. Controls considered were: (a) overall caprock hydraulic conductivity; and (b) stratigraphic variations of hydraulic conductivity in the caprock. Within the caprock, variations in hydraulic conductivity, caused by stratigraphy or discontinuities of the stratigraphic units, are a major control on the direction of groundwater flow and the distribution of water levels and salinity. Results of cross-sectional modeling confirm the general groundwater flow pattern that would be expected in a layered coastal system. Groundwater flow is: (a) predominantly upward in the low-permeability sedimentary units; and (b) predominantly horizontal in the high-permeability sedimentary units. Received, October 1996 Revised, August 1997 Accepted, September 1997  相似文献   

19.
A map shows intrinsic vulnerability to pollution of the Chrzanów karst-fissured aquifer (273 km2) in the southern part of Poland. This aquifer is intensively drained by numerous intakes and Zn-Pb ore mines. A DRASTIC-type parametric system was applied for groundwater vulnerability evaluation. Vulnerability assessment is based on six factors (depth to groundwater table, lithology of the unsaturated zone, net recharge, hydraulic conductivity of the aquifer, groundwater flow velocity, aquifer thickness). For the final vulnerability map construction at the scale of 1:50,000, a combination of the aquifer simulation model (using MODFLOW) and a geographical information system was applied. Maps of the net recharge, hydraulic conductivity of the aquifer and groundwater flow velocity were derived by aquifer modelling. Based on the vulnerability index (21-182), six relative vulnerability classes were selected. Reliability of the map has been verified.  相似文献   

20.
A poroelastic numerical model is presented to evaluate three-dimensional consolidation due to groundwater withdrawal from desaturating anisotropic porous media. This numerical model is developed based on the fully coupled governing equations for groundwater flow in deforming variably saturated porous media and the Galerkin finite element method. Two different cases of unsaturated aquifers are simulated for the purpose of comparison: a cross-anisotropic soil aquifer, and a corresponding isotropic soil aquifer composed of a geometrically averaged equivalent material. The numerical simulation results show that the anisotropy has a significant effect on the shapes of three-dimensional hydraulic head distribution and displacement vector fields. Such an effect of anisotropy is caused by the uneven partitioning of the hydraulic pumping stress between the vertical and horizontal directions in both groundwater flow field and solid skeleton deformation field. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号