首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 421 毫秒
1.
Data concerning runoff and sediment yield in arid zones is of prime importance for hydrologists, geomorphologists, pedologists, ecologists and landscape engineers. For data comparison and extrapolations, runoff and sediment yield are often presented in mass per unit area. Runoff and sediment yield collected on dune slopes over a wide range of plot sizes during 1990–1994 in the Negev Desert, Israel, showed that the contributing area was mainly confined to a narrow belt at the bottom of the slopes. It was therefore hypothesized that the very short rain bursts, capable of runoff generation, may result in a scale effect (SE). Indeed, average duration of duration of consecutive medium and high rain intensities which are potentially above the surface infiltration rate ranged between 2.2 and 3.0 minutes, implying that flow connectivity is largely limited. Based on the intermittent character of the rain spells capable of runoff generation it is argued that SE is an inherent outcome of the rain properties. Yet, it is further argued that the magnitude of the SE is surface‐dependent. As a result, it is argued that the conventional way for runoff and sediment yield presentation as mass per unit area implies theoretical misconceptions and may cause gross overestimation in extrapolation and the presentation of runoff and sediment yield in mass per unit width of the slope is suggested. The accuracy of the two extrapolation methods are compared to the actual runoff and sediment yield collected in the field. The data show that extrapolation based on runoff (or sediment) yield per plot width deviates from the actual amounts collected by a factor of 1·1 to 1·3 only while deviating by a factor of 4·2 to 5·6 and 10·7 to 11·8 if the extrapolation is based on large and small plots, respectively. Theoretical and practical reasons for presentation of runoff and sediment yield as mass per unit width are discussed. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

2.
Defining reference conditions for lakes situated in areas of human settlement and agriculture is rarely straightforward, and is especially difficult within easily eroding and nutrient rich watersheds. We used diatoms, cyanobaterial akinetes, remains of green algae and chironomid head capsules from sediment samples of Lake Kirmanjärvi, Finland, to assess its deviation from the initial ecological status. These site-specific records of change were compared to current type-specific ecological status assessment. All paleolimnological data indicated deviation from natural conditions and mirrored the current, monitoring-based assessment of “moderate” ecological lake status. However, the sediment data showed that the lake should be re-typified as a naturally eutrophic lake. Sediment records as well as current monitoring data indicated temporary improvement in water quality in response to extensive fish manipulation. Our results suggest that paleolimnological records can be used to derive site-specific reference conditions and that extensive restoration efforts can result in gradual, observable improvements of water quality and ecological status.  相似文献   

3.
The surficial characteristics and precipitation regime of sparsely vegetated hillslopes in the montane zone of the Colorado Front Range suggest that rainsplash may be an important component of the surficial debris cascade. Site sediment flux data from two study periods reveal marked spatial and temporal variability. Comparison of these date with sediment movement data from splashcups suggests the following conclusions: (1) Detachment rates of the rainsplash process appear great enough to account for the sediment flux in the open Gerlach-type traps; (2) Areal extrapolation of rainsplash transport suggest that 88 per cent of the fine sediment flux in 1982 can be attributed to rainsplash; (3) Estimates of rainfall energy and changes in the potential energy of hillslopes by mass transport suggests a process efficiency of 0.05 per cent for rainsplash. If this procedure is applied to sediment flux values from open traps, the low precipitation-energy cascade of 1982 appears to be largely rainsplash-transported sediment. Extrapolation with the 1981 data suggests more aggressive overland flow erosion and transport.  相似文献   

4.
The objective of this research is to investigate spatial and temporal variation in the transport of phosphate by grain size fractions of suspended sediment in two Lake Erie tributaries. A sediment-phosphate transport model is proposed to evaluate and quantify the kinetic control of dissolved phosphate by fluvial sediment. A first-order assessment of the sediment-phosphate export from Big Otter Creek and Big Creek to Lake Erie is presented. Output from this model was calculated using historical discharge and sediment data collected by Environment Canada in combination with adsorption coefficients derived from laboratory experiments for a range of sediment grain size fractions. Results of these calculations provide a quantitative interpretation of the influence of suspended sediment on phosphate dynamics in tributaries and the potential impact on water quality of receiving waters.  相似文献   

5.
The utility of sediment budget analysis is explored in revealing spatio‐temporal changes in the sediment dynamics and morphological responses of a fluvial system subject to significant human impacts during the recent Anthropocene. Sediment budgets require a data‐intensive approach to represent spatially‐differentiated impacts adequately and are subject to numerous estimation uncertainties. Here, field and topographic surveys, historical data, numerical modelling and a representative‐area extrapolation method are integrated to construct a distributed, process‐based sediment budget that addresses historical legacy factors for the highly regulated Lagunitas Creek (213 km2), California, USA, for the period 1983–2008. Independent corroboration methods and error propagation analysis produce an uncertainty assessment unique to a catchment of this size. Current sediment yields of ~20 000 t a‐1 ± 6000 t a‐1 equate to unit rates of ~300 t km‐2 a‐1 ± 90 t km‐2 a‐1 over the effective sediment contributing area of 64 km2. This is comparable with yields associated with early Euro‐American settlement in the catchment, despite loss of sediment supply upstream of the two large dams. It occurs because ~57% of the sediment is now derived from incision‐related channel erosion. Further, the highly efficient routing of channel‐derived sediments in these incised channels suggests an efflux of 84% of contemporary sediment production, contrasting with the efflux of ≈10–30% reported for unregulated agricultural catchments. The results highlight that sediment budgets for regulated rivers must accommodate channel morphological responses to avoid significantly misrepresenting catchment yields, and that volumetric precision in sediment budgets may best be improved by repeat, spatially dense, channel cross‐section surveys. Human activities have impacted every aspect of the sediment dynamics of Lagunitas Creek (production, storage, transfer, rates of movement through storage), confirming that, while distributed sediment budgets are data demanding and subject to numerous error sources, the approach can provide valuable insights into Anthropocene fluvial geomorphology. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

6.
A combination of two indirect methods to measure sediment flux is presented in this study to evaluate suspended sediment transport in a hydropower reservoir. The acoustic backscatter signal (ABS) from an Acoustic Doppler Current Profiler (ADCP) is therefore applied in pre-defined transects within the reservoir in combination with a Laser In-Situ Scattering Transmissometry – stream lined device (LISST-SL). The stationary LISST-SL derived suspended sediment concentration (SSC) measurements are used to calibrate the ABS. From the LISST-SL measurements a time series of SSC is obtained. This enables, in addition, a comprehensive data analysis to evaluate the influence of natural fluctuations of the SSC on the calculated sediment flux, which should be taken into account when assessing sediment transport. Furthermore SSC measurements are done with the LISST-SL close to the reservoir bed. In areas close to the bed no information regarding the ABS is available from the ADCP measurements due to the side-lobe interference. In various studies the information from the last three valid cells is used for extrapolation. However, as result of a comparison of the LISST-SL measurements with extrapolated SSC values from the ADCP measurements it can be seen that, especially in deep reservoirs, this method has to be adapted to the in-situ conditions.  相似文献   

7.
A. O. Pektas 《水文科学杂志》2017,62(10):1694-1703
Suspended sediment modelling is a quite significant issue in hydrology. The prediction of suspended sediment has taken the attention of several scientists in water resources. With extrapolation, the forecasting ability of the employed forecasting model beyond the calibration range is investigated. In the present study, different smoothing parameters are used to differentiate the kurtosis of the local critical points (local minima and maxima). The two models used are an artificial neural network (ANN) model and a multiple linear regression (MLR) model for prediction in order to examine the model extrapolation ability. The ANN model provides closer estimations to the observed peaks, being higher than the corresponding MLR ones. For the local minima, the ANN predictions are higher than the MLR predictions. As there are limited local points, all the remaining ANN predictions are lower than the MLR ones except for one point.  相似文献   

8.
  相似文献   

9.
1 INTRODUCTION Sediment and nutrients from a watershed may adversely affect a downstream reservoir by reducing its capacity or degrading water quality. Among the output nutrients, phosphorus is often a growth-limiting element for aquatic organisms and pla…  相似文献   

10.
The aqueous environmental quality of the Haihe River Basin is crucial for the ecological health of local catchments and the Bohai Sea. For the routine management neglected sediment tests and no legitimate tool supported the toxicity evaluation yet, one supplementary monitoring was implemented to examine the occurrence and toxic level of sediment metals in the lower reaches of the Haihe River Basin in 2009. Both world-widely used consensus-based sediment quality guidelines and China's environmental quality standard for soils (EQSS) were used as assessment tools. Cu, Zn, As, Hg, Cd, and Pb were detected in all 24 samples, while Cr was detected in 18 samples. Assessment results showed 9 samples were toxic and the most dominant toxic element was As. Although the river water quality is getting better, sediment metals have accumulated over thirty years due to continuous industrial development, with toxicity far beyond safety limitations. The highest toxicity levels were encountered in Binhai New Area, suggesting three rivers should be given priority for restoration. It is found that EQSS is also applicable for sediment toxicity assessment until a dedicated tool for Haihe River Basin is available, except for that EQSS is too conservative for Pb.  相似文献   

11.
Abstract

The Pennsylvania Department of Transportation and the US Geological Survey are cooperating in several field studies to evaluate sediment control measures used during highway construction. Among the parameters being monitored are suspended sediment concentration and turbidity. Sediment loads are calculated from suspended sediment and water discharge data, but some sediment loads must be determined indirectly because it is virtually impossible to obtain sufficient suspended sediment samples to define all runoff conditions adequately. Sediment discharge-water discharge correlation curves have proved unreliable for streams affected by highway construction, so an alternative method using the turbidity record was developed during these studies.

The field data reveal a good correlation between daily mean discharge-weighted turbidity and daily mean discharge-weighted suspended sediment concentration. Turbidity is monitored and recorded continuously, and the daily mean discharge-weighted turbidity is calculated from the turbidity and water discharge data. During periods when there are insufficient suspended sediment data, the daily mean discharge-weighted suspended sediment concentration is determined from the turbidity-sediment correlation and used with the daily mean water discharge to calculate a daily sediment load.

This method of determining sediment loads from the turbidity record suggests a possiblity for computation of sediment loads by computer. Instrumentation now in use for recording water quality parameters on digital punch tape could be used to record the output from a turbidimeter. Then, for streams having a good correlation between suspended sediment concentration and turbidity, simultaneous water discharge and turbidity data could be used to determine sediment loads by computer.  相似文献   

12.
Model calibration and validation are necessary before applying it for scenario assessment and watershed management.This study presented the methodology of evaluating Soil and Water Assessment Tool(SWAT) and tested the feasibility of SWAT on runoff and sediment load simulation in the Zhifanggou watershed located in hilly-gullied region of China.Daily runoff and sediment event data from 1998-2008 were used in this study;data from 1998-2003 were used for calibration and 2004-2008 for validation.The evaluation statistics for the daily runoff simulation showed that the model results were acceptable,but the model underestimated the runoff for high-flow events.For sediment load simulation,the SWAT performed well in capturing the trend of sediment load,while the model tended to underestimate sediment load during both the calibration and validation periods. The disparity between observed and simulated data most likely resulted from limitations of the existing SCS-CN and MUSLE methods in the model.This study indicated that the modification of SWAT components is needed to take rainfall intensity and its duration into account to enhance the model performance on peak flow and sediment load simulation during heavy rainfall season.  相似文献   

13.
Deriving sediment quality guidelines (SQGs) for marine sediments is a difficult task. It will often be a trade off between reproducibility and relevance. One of the fundamental questions in ecotoxicology is to decide what one should measure to detect response in ecosystems exposed to human disturbance. In this paper we use field data to estimate threshold levels eliciting effects on soft bottom macrobenthos collected at different sediment types and depths on the Norwegian Continental Shelf and test these against natural levels occurring levels in reference conditions. SQGs are presented from multivariate analyses based on 121 gradients (represented with Ba, THC, Cd, Cu, Pb and Zn) incorporating more than 2000 species. Clear clusters with slightly disturbed communities related to contamination loadings were evident in 35% of the gradients. We found large variations in naturally occurring contamination concentrations and in the threshold levels electing effects on the fauna at different sediment types and depths. For example, an increase in depth of only 100 m can triple the Cu and Zn concentrations that elicit effects. Lowest background and threshold levels were found in shallow, sandy sediment. Our results suggest that current SQGs are too high. We hypothesised that setting a SQG of 4-times background concentrations will give sufficient protection for the fauna from metal contamination. The overall background concentration eliciting effects on metal was 3.6x.  相似文献   

14.
ABSTRACT

This study describes the assessment of reservoir sedimentation of the Patratu Reservoir using Satellite Remote Sensing (SRS). The sedimentation assessment was carried out using satellite data and reservoir water level data from 2006 to 2012. Water spread area was analysed from satellite data. The Normalized Difference Water Index (NDWI) has been used to delineate open water features and to enhance the presence of water surface in satellite imagery of the Patratu Reservoir. Water spread area of the reservoir at a particular elevation on the date of the passing of the satellite was used to develop an elevation-area curve. For the present case, fluctuation of water level was found to vary from 387.096 to 406.152 m. The linear interpolation/extrapolation technique has been employed to assess the water spread area of Patratu Reservoir at different elevations. Further, these areas were used to compute the live storage capacity of the reservoir between two elevations by the Prismoidal formula. From the study, it was found that due to sedimentation, the live storage capacity of Patratu Reservoir has reduced from 101.95 to 89.96 hm3, thus showing capacity loss of 11.76% in a span of 44 years. To increase the live storage capacity of the reservoir it is proposed to adopt manual and mechanical digging combined with flushing for desilting of the deposited sediment.
EDITOR D. Koutsoyiannis ASSOCIATE EDITOR S. Kanae  相似文献   

15.
In the current research,the impact of the COVID-19 lockdown period on sediment quality of the MericErgene River Basin was evaluated by determining the potentially toxic elements（PTEs） in sediment samples collected from 25 sampling points in the basin.Also some important ecological indicators including potential ecological risk index（PERI）,contamination factor（CF）,pollution load index（PLI）,biological risk index（BRI）,and geo-accumulation index(Igeo) and some important statistical indica...  相似文献   

16.
Abstract

Estimates of average annual sediment production in the 4,560 square mile Umpqua River basin in southwest Oregon were developed to assess impacts of land condition, use, and management in the watershed on quality of the water produced. Specific attention was given to channel bankcutting, scour, and deposition; to signs of erosion on the land, occurrence of landslides, and effects of cultivation, timber harvest, grazing, and road construction. Sediment production was estimated and ratings given each tributary drainage in five classes: slight, low, moderate, high, and very high; corresponding to average sediment loads of less than 50 ppm, 50 to 150 ppm, 150 to 500 ppm, 500 to 1500 ppm, and over 1500 ppm carried by the average annual flow. Areas and rating were checked against measured sediment loads, allowing for the fact that the sampling did not include the infrequent high flows which carry a disproportionate share of total sediment load.

Information on geology was available for half the basin; on soil characteristics for a fifth of the area, including some of the forested mountain land. Aerial photo coverage was complete. Suspended load sampling at ten stations, done at two-week intervals for the preceding five years, furnished a fair indicator of sediment movement. Soils and geology information included erodibility and slump and slide hazard indices, and was used to guide field ratings and to extend them to areas not visited. Aerial photographs were used for extrapolation to areas for which soils and geology had not been mapped.  相似文献   

17.
High sediment concentrations in runoff are a characteristic feature of the Chinese Loess Plateau, and are probably caused by factors such as the occurrence of erodible materials on steep slopes, the characteristics of the loess and the harsh climate that results in low plant cover. When sediment concentration increases, fluid density increases, viscosity increases and settling velocity decreases. These effects become increasingly important with increasing concentration and can result in flow behaviour that is quite different from that of clear water flow. Although the net effect of these changes on the flow is not always apparent, erosion models that deal with high sediment concentrations should consider such effects and could include corrections for some of these effects. A case study in a small catchment on the Loess Plateau indicated that sediment concentrations were considerable, and literature data suggested that for such sediment concentrations, corrections for settling velocity, fluid density and viscosity are needed. Furthermore, a number of corrections are necessary to be able to compare field measurements with results of soil erosion models: sediment volume should be subtracted from runoff volume and a density correction is needed to use data from a pressure transducer. For flumes that were used to measure discharge from smaller areas inside the catchment, the measured water level should be corrected by subtracting the sediment level in the flume from the water level, while the sediment volume should also be subtracted from the discharge. Finally, measured concentration should be corrected to give concentration expressed as grams per litre of clear water, since soil erosion models express sediment concentration in this way. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

18.
The European Water Framework Directive (WFD) establishes a framework for the protection and improvement of estuarine (transitional) and coastal waters, attempting to achieve good water status by 2015; this includes, within the assessment, biological and chemical elements. The European Commission has proposed a list of priority dangerous substances (including metals such as Cd, Hg, Ni and Pb), with the corresponding list of environmental quality standards (EQS), to assess chemical status, but only for waters. In this contribution, a long-term (1995–2007) dataset of transitional and coastal water and sediment trace elements concentrations, from the Basque Country (northern Spain), has been used to investigate the response of these systems to water treatment programmes. Moreover, the approach proposed in the WFD, for assessing water chemical status (the ‘one out, all out’ approach), is compared with the integration of water and sediment data, into a unique assessment. For this exercise, background levels are used as reference conditions, identifying the boundary between high and good chemical status. EQS are used as the boundary between good and moderate chemical status. This contribution reveals that the first approach can lead to misclassification, with the second approach representing the pattern shown by the long-term data trends. Finally, the management implications, using each approach are discussed.  相似文献   

19.
Migration is essential to seismic imaging. It is carried out by backward extrapolation of the wavefield registered on the observation surface. The quality of images depends on the accuracy of the wavefield reconstruction at interior subsurface points. From the theory based on the exact solution of the scalar wave equation it is known that, for accurate wave extrapolation, data must be obtained from an infinite observation surface. Limiting of migration apertures, which is inevitable in practice, leads to artefacts in extrapolated fields. The distortion they cause in 2D and 3D imaging is different. In 2D migration, the artefacts known as truncation effects are much weaker than the signals being extrapolated and for this reason attract no special attention. In 3D migration, diffractions caused by an aperture edge are stronger and may create serious problems. For a circular aperture, their amplitudes are comparable to the amplitudes of the signals themselves. The study of aperture diffractions is intended to help in the search for ways of either suppressing them efficiently or deliberately utilizing them in order to improve imaging.
In optics, diffractions by an aperture play a constructive role in image making. This research shows that the same may take place in seismic imaging.  相似文献   

20.
Stochastic methods in hydraulics and hydrology of streamflow are presented. The hydraulics part consists of mechanics of streamflow and sediment transport. A technique presented herein enables one to analyze a limited amount of field data to determine the stochastic structure of irregular stream geometry so that cross-sections and slopes of a stream may be simulated wherever, or as many as, needed. It provides the rational basis of efficient use, interpolation, and extrapolation of field data of irregular stream geometry for any studies to understand and control transport processes in streams. Stochastic modelings of motion of a single sediment particle, either in suspension or on the stream bed, help in understanding the complex mechanism governing sediment transport and, hence, improving techniques for calculating the spatial distribution and transport rate of sediment. For practical applications, however, the technique combining the stochastic and deterministic methods should be most effective.In the hydrology part, Markov and non-Markov models are presented which may be used to simulate streamflow data. Markov models, which dominated stochastic hydrology in the past, have short memories and, therefore, cannot preserve or simulate long-term persistence characterizing physiscal streamflows. Non-Markov models which are currently being developed, and may or may not belong to the Brownian domain, have very long or infinite memories.This paper is dedicated to the idea of coupling the stochastic and deterministic methods in hydraulics and hydrology, so that the two methods may contribute their strengths while complementing each other for their weaknesses.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号