共查询到20条相似文献，搜索用时 93 毫秒
1.
The initial acquisition of direct-sequence spread-spectrum (DSSS) signal transmitted in bursts by ground terminals at satellite-borne receiver poses an engineering challenge. We propose a low-complexity acquisition algorithm that is capable of capturing extremely weak DSSS signal in the presence of large Doppler dynamics. The algorithm uses fast Fourier transform (FFT)-based frequency-domain techniques to implement circular correlations between the received signal and the local pseudo-random noise (PRN) code, and it coherently accumulates the correlation results across multiple PRN code periods, to achieve a sufficient signal–noise ratio for reliable acquisition. We invoke another FFT procedure to perform the coherent accumulation and the fine compensation for the residual Doppler frequency offset. To highlight the advantage of the proposed algorithm, we make a complexity comparison among the proposed algorithm and two other benchmark strategies, namely the modified double block zero padding (MDBZP) and two-dimensional exhaustive search (2D-ES). It is shown that the proposed algorithm has the lowest complexity, which is particularly desirable for satellite-borne receivers where the computational resource is limited. The acquisition performance of the proposed algorithm is verified by theoretical analysis and Monte Carlo simulations and compared with that of MDBZP and 2D-ES. Moreover, we have carried out extensive tests on a hardware verification system, and we show the claimed tradeoff between performance and cost is indeed attainable with the suggested algorithm. Numerically, it is found the proposed algorithm can achieve a detection rate of 0.9 and a false alarm rate of \(10^{ - 5}\) at C/N 0 = 29.5 dBHz over a Doppler frequency offset range of \(\left[ { - 7.5\,{\text{kHz}},7.5\,{\text{kHz}}} \right]\) in floating-point simulation, which coincides with the analytical results. The same performance is achieved at C/N 0 = 31 dBHz in fixed-point simulation and at C/N 0 = 31.5 dBHz on a hardware system. 相似文献
2.
本文给出了GPS/GLONASS双模接收机的总体设计方案,重点对弱信号环境下的接收机信号捕获进行了讨论,采用并行码相位搜索方法和改进的循环相关算法分别对GLONASS信号和GPS信号进行捕获;并利用真实数据对双模接收机性能进行了仿真研究,重点对接收机捕获弱信号的能力,以及在不同信噪比和不同累加数据长度下的捕获概率进行了讨论,结果表明该双模接收机在不需要较长数据长度的情况下能够捕获低信噪比环境下的卫星导航信号,提高了接收机的灵敏度。 相似文献
3.
Fast direct GPS P-Code acquisition 总被引：5，自引：0，他引：5
GPS P-Code has a higher chipping rate, better accuracy, and anti-jamming property than C/A code. Traditionally, GPS P-Code acquisition depends on handover from C/A code. This potentially needs long acquisition time. Moreover, when C/A code is not available, it is no longer possible to acquire GPS P-Code through handover from C/A code. The purpose of this paper is to describe a new overlap average method to facilitate hardware design of fast direct P-Code acquisition. It allows the rapid code phase search to acquire GPS P-Code signals, and also decreases the hardware resource requirement. The small size FFT in the proposed methods is very promising for fast FPGA hardware system design using FFT cores. The simulation results and theoretical analysis are included demonstrating the overall performance of the proposed method.
相似文献
| Jing PangEmail: Phone: +1-916-2784549Fax: +1-916-2787215 |
4.
在已有的极化合成孔径雷达(PolSAR)图像恒虚警(CFAR)检测方法中,存在着高分辨下杂波模型适用性差的难题。为解决此问题,提出了一种G_0分布下虚警概率具有闭合解析表达形式的CFAR检测方法,并定义虚警损失率(CFAR Loss, C_L)参数用以量化评估CFAR检测方法的恒虚警保持效果。首先,在乘积模型框架下,引入了逆Gamma纹理变量假设,推导出了多视极化白化滤波(MPWF)检测量的概率密度函数(PDF)。然后,对MPWF检测量的概率密度函数积分得到了虚警概率关于CFAR检测阈值的解析表达式,并设计了相应的CFAR检测流程。最后,采用仿真数据和AIRSAR实测数据对已有方法和新方法进行了算法运行时间、检测量拟合性能及目标检测性能对比。实验结果表明,方法运行时间比已有方法缩短3至30倍,具有良好的实时性;日本玉野地区的AIRSAR实测数据结果表明G_0分布对高分辨不均匀海区具有良好的拟合性能,且新方法在G_0分布和非G_0分布海区均能有效检测出目标,鲁棒性较强,相比其他检测方法品质因数(FoM)平均高出15.78%;C_L分析结果表明新方法具有良好的恒虚警保持性能,同时指出杂波对数累积量散点距离G_0分布曲线越近,新方法的恒虚警保持效果越好。 相似文献
5.
BOC(binary offset carrier)信号自相关函数存在多值性,BOC信号的捕获不能简单地移植GPS信号捕获算法。在分析经典并行码相位算法和BOC信号互相关特性基础上,仿真分析了并行码相位搜索算法对BOC信号进行捕获的有效性,并针对经典算法在低信噪比条件下捕获信号存在的不足,对经典算法进行了改进设计,并利用改进算法对多种BOC信号进行了仿真分析。结果表明,本文提出的改进捕获算法适用于BOC(pn,n)信号(p为整数),扩展了经典算法的适用范围,且与经典算法相比,改进捕获算法对所给定BOC信号能够改善捕获信噪比10dB,可显著提高接收机捕获灵敏度,对接收机BOC信号捕获算法设计具有重要意义。 相似文献
6.
We present a multi-constellation multi-band GNSS software receiver front end based on USRP2, a general purpose radio platform. When integrated with appropriate daughter boards, the USRP2 can be used to collect raw intermediate frequency (IF) data covering the entire GNSS family of signals. In this study, C++ class-based software receiver processing functions were developed to process the IF data for GPS L1, L2C, and L5 and GLONASS L1 and L2 signals collected by the USRP2 front end. The front end performance is evaluated against the outputs of a high end custom front end driven by the same local oscillator and two commercial receivers, all using the same real signal sources. The results show that for GPS signals, the USRP2 front end typically generates carrier-to-noise ratio (C/N 0) at 1–3 and 1–2 dB below that of the high end front end and a NovAtel receiver, respectively. For GLONASS signals, the USRP2 C/N 0 outputs are comparable to those of a Septentrio receiver. The carrier phase noise from the USRP2 outputs is similar to those of the benchmarking devices. These results demonstrate that the USRP2 is a suitable front end for applications, such as ionosphere scintillation studies. 相似文献
7.
部分匹配滤波器与FFT相结合的捕获模型使用在高动态环境下导航信号的捕获中,由于它对多普勒频率误差有较高的容忍度,因此可以直接进行频域的并行搜索,大大降低了平均搜索时间,并使整个系统依然具有较高的检测概率. 文中通过建立数学模型,对PMF FFT捕获算法的原理及特性及其在捕获流程中的各部分损耗进行了详细的分析,并针对P码的非周期特性,使用重叠保留法对PMF FFT算法进行了改进,使用基于FFT的并行码相位搜索的方法,在频域内实现了时域相关运算,进一步减少了捕获时间. 最后依据“达到等效判决信噪比时总运算时间最少”原则,对算法中各项参数的设计提出了指导意见,具有一定的参考价值。 相似文献
8.
An acquisition method is proposed which saves processing time and rapidly finds the Global Positioning System (GPS) satellite
with high receiving power. The idea is to combine two or more Coarse/Acquisition (C/A) codes to process acquisition, thus
called “multi-C/A code acquisition method.” The proposed method will change the procedure of conventional Fast Fourier Transform
acquisition slightly, and it has the capabilities to combine with other acquisition methods to perform signal acquisition
simultaneously. In order to show how this multi-C/A code acquisition method may improve the Time To First Fix at the cold
start, the real raw Intermediate Frequency data from a GPS software receiver are used to validate this multi-C/A code acquisition
method. The results show that this method can save at least 23% processing time and it is able to detect the satellite more
rapidly. 相似文献
9.
We address the problem of estimating the carrier-to-noise ratio (C/N0) in weak signal conditions. There are several environments, such as forested areas, indoor buildings and urban canyons, where high-sensitivity global navigation satellite system (HS-GNSS) receivers are expected to work under these reception conditions. The acquisition of weak signals from the satellites requires the use of post-detection integration (PDI) techniques to accumulate enough energy to detect them. However, due to the attenuation suffered by these signals, estimating their C/N0 becomes a challenge. Measurements of C/N0 are important in many applications of HS-GNSS receivers such as the determination of a detection threshold or the mitigation of near-far problems. For this reason, different techniques have been proposed in the literature to estimate the C/N0, but they only work properly in the high C/N0 region where the coherent integration is enough to acquire the satellites. We derive four C/N0 estimators that are specially designed for HS-GNSS snapshot receivers and only use the output of a PDI technique to perform the estimation. We consider four PDI techniques, namely non-coherent PDI, non-quadratic non-coherent PDI, differential PDI and truncated generalized PDI and we obtain the corresponding C/N0 estimator for each of them. Our performance analysis shows a significant advantage of the proposed estimators with respect to other C/N0 estimators available in the literature in terms of estimation accuracy and computational resources. 相似文献
10.
为了满足高动态用户及强干扰条件下的应用需求,提出了一种基于卫星信号矢量跟踪的SINS/GPS深组合导航方法,设计了基于FPGA硬件平台的实施方案。利用组合卡尔曼滤波器反馈回路取代了传统接收机中独立、并行的跟踪环路,能够同时完成所有可视卫星信号的跟踪和导航信息处理;通过矢量跟踪算法对所有可视卫星信号进行集中处理,能够增强跟踪通道对信号载噪比变化的适应能力,从而提高接收机在强干扰或信号中断条件下的跟踪性能;根据SINS导航参数和星历信息推测GPS伪码相位和多普勒频移等参数,用以辅助卫星信号的捕获和跟踪,能够大大缩短接收机的搜索捕获时间,并增强接收机在高动态条件下的跟踪性能。基于矢量跟踪的深组合方法不仅在GPS信号短暂中断期间,能够保证系统的导航精度和可靠性,而且在强干扰环境中能够维持较好的伪码相位和载波频率跟踪性能。 相似文献
11.
根据干涉图信号和噪声时频分布差异的特点,提出一种改进的基于经验模态分解EEMD的InSAR干涉相位滤波方法。该方法首先利用可有效降低模态混叠的EEMD算法,对干涉图的实部及虚部分别进行2维经验模态分解,获得具有不同时间尺度的模态分量;然后根据信号和噪声分量的时间尺度分布特性的差异,采用适用于非线性信号分析的KECA算法对噪声识别、分离;最后利用去除噪声后的模态分量重构干涉图。为了证明本文方法的有效性,分别利用模拟数据及真实InSAR差分干涉相位进行滤波试验。对比本文EEMD-KECA滤波方法、Goldstein滤波、圆周期—中值滤波、EMD分解、EMD-PCA方法的滤波效果,采用相干斑指数、均方差指数、边缘保持指数进行定量评价。结果表明,与经典InSAR干涉图滤波方法相比,本文联合EEMD-KECA算法的滤波方法能有效滤除干涉图噪声,且在条纹边缘等细节信息的保持上也具有较大优势。 相似文献
12.
Markus Irsigler 《GPS Solutions》2010,14(4):305-317
A well-known effect of multipath propagation is multipath fading that typically causes periodic signal variations. Such signal
variations may become visible in some basic GNSS observables such as the code minus carrier observable, single or double differences
or in C/N
0 time series. The frequency of these variations—also called fading frequency or multipath phase rate—strongly depends on the
multipath environment, i.e. on the actual geometric conditions which can be described by the location of the satellite causing
the multipath signal and the reflector location with respect to the receiving antenna. This paper gives a detailed insight
on the expected multipath phase rates in different multipath environments. Different geometric conditions are analyzed, from
arbitrary reflector positions to the point of dealing with the special case of ground multipath. Fading frequencies are determined
by means of an empirical approach using the characteristics of real satellite passes. The approach results in distributions
of multipath phase rates which are computed for a multitude of possible reflector locations and from which minimum, mean and
maximum multipath phase rates can be derived. 相似文献
13.
Much of the research into multipath detection and mitigation has not considered the carrier phase delay between the line of
sight (LOS) and reflected signals. A new variable referred to as early late phase (ELP) has recently been proposed to exploit
this phase difference. It has been found that in a receiver tracking the L1 GPS signal, the probability of detecting multipath
is lower when the carrier phase difference between the LOS and a reflected signal is an integer multiple of π. Since the pseudorange
error caused by the multipath’s presence is the highest in this case, we propose to exploit the coexistence of another GPS
civilian signal, the L2C. We present an analysis of ELP for the L1 and L2C signals, and a combination of both, for detecting
multipath. The multipath detection performance has been compared using probabilities of false alarm and detection. An ideal
algorithm should have lower probability of false alarm and higher probability of detection. However, it has been found that
using dual-frequency ELP increases both probabilities. Thus, receiver operator characteristics (ROC) curves, and the area
under the ROC curves, have been used for effective comparison. It has been found that the L2C signal individually gives worse
performance than L1 because of its weaker signal strength. However, the combination of L1 and L2C gives the best overall performance,
and thus it can be claimed that ELP using dual-frequency receivers is a more effective approach for detecting multipath. 相似文献
14.
NLOS GPS signal detection using a dual-polarisation antenna 总被引：2，自引：2，他引：0
The reception of indirect signals, either in the form of non-line-of-sight (NLOS) reception or multipath interference, is a major cause of GNSS position errors in urban environments. We explore the potential of using dual-polarisation antenna technology for detecting and mitigating the reception of NLOS signals and severe multipath interference. The new technique computes the value of the carrier-power-to-noise-density (C/N 0) measurements from left-hand circular polarised outputs subtracted from the right-hand circular polarised C/N 0 counterpart. If this quality is negative, NLOS signal reception is assumed. If the C/N 0 difference is positive, but falls below a threshold based on its lower bound in an open-sky environment, severe multipath interference is assumed. Results from two experiments are presented. Open-field testing was first performed to characterise the antenna behaviour and determine a suitable multipath detection threshold. The techniques were then tested in a dense urban area. Using the new method, two signals in the urban data were identified as NLOS-only reception during the occupation period at one station, while the majority of the remaining signals present were subject to a mixture of NLOS reception and severe multipath interference. The point positioning results were dramatically improved by excluding the detected NLOS measurements. The new technique is suited to a wide range of static ground applications based on our results. 相似文献
15.
Cycle slip detection and repair for undifferenced GPS observations under high ionospheric activity 总被引：3，自引：3，他引：0
We develop a new approach for cycle slip detection and repair under high ionospheric activity using undifferenced dual-frequency GPS carrier phase observations. A forward and backward moving window averaging (FBMWA) algorithm and a second-order, time-difference phase ionospheric residual (STPIR) algorithm are integrated to jointly detect and repair cycle slips. The FBMWA algorithm is proposed to detect cycle slips from the widelane ambiguity of Melbourne–Wübbena linear combination observable. The FBMWA algorithm has the advantage of reducing the noise level of widelane ambiguities, even if the GPS data are observed under rapid ionospheric variations. Thus, the detection of slips of one cycle becomes possible. The STPIR algorithm can better remove the trend component of ionospheric variations compared to the normally used first-order, time-difference phase ionospheric residual method. The combination of STPIR and FBMWA algorithms can uniquely determine the cycle slips at both GPS L 1 and L 2 frequencies. The proposed approach has been tested using data collected under different levels of ionospheric activities with simulated cycle slips. The results indicate that this approach is effective even under active ionospheric conditions. 相似文献
16.
提出一种结合子孔径相关测度的时序高相干点探测方法,首先对时序SAR影像进行谱分解获得子孔径视图,通过时序子孔径相关测度进行强散射点筛选,然后分别根据振幅离差和干涉相位空间相关性,对目标点进行相位稳定性分析,探测出既满足强散射且在时间序列上散射稳定的高相干点。利用改进的点探测方法和短基线INSAR技术,对北京2003—2009年间40景ASAR影像进行相位建模,获取地面沉降时空分布特征,分析典型地物时序沉降过程,研究北京地面沉降与地下水开采关系。结果表明:相比已有方法,本文结合子孔径相关测度的高相干点探测结果更准确可靠;利用本文点探测方法反演的历史累积沉降信息,与水准结果一致,平均速率之差在3.69 mm/a以内,中误差为1.36 mm/a;研究区地面沉降最大速率达92.25 mm/a,空间不均匀分布明显,地面沉降量与地下水开采量呈分段的非线性相关。 相似文献
17.
弱GPS信号捕获算法及其仿真研究 总被引：1，自引：0，他引：1
为满足低信噪比环境下的导航需要,介绍了一种基于改进循环相关的GPS基带信号捕获算法。本文借助于GPS信号基带数学模型以及FFT技术,从理论层面上对捕获算法的信号处理流程以及捕获性能进行了分析;并利用真实GPS基带数据对算法在低信噪比环境下的检测概率和捕获能力进行了重点仿真,仿真结果显示算法在低信噪比环境下是有效的,能够提高低信噪比环境下的检测概率和提高GPS接收机的检测灵敏度。 相似文献
18.
随着卫星导航定位技术及接收机的发展,软件接收机已成为当前研究的热点之一。根据北斗卫星导航定位系统（BDS）的接口控制文档（ICD）,分析了BDS B1I信号,提出了一种基于并行码相位和并行频率捕获的算法,实现了对BDS-B1I/GPS信号的捕获跟踪、导航电文解码。利用HG-SOFTGPS02采集器采集的数据进行BDS/GPS定位,验证了该算法的可行性与合理性。 相似文献
19.
北斗三号卫星导航系统（BDS-3）B1C信号相较北斗二号卫星导航系统卫星信号,从信号结构、编码方式再到导航电文结构都发生了改变,包括引入导频信号、二次编码、BOC调制、LDPC编码和B-CNAV1导航电文结构等.这些改变一方面提高了信号性能(如抗多路径、信号捕获和跟踪精度等);另一方面,也带来了一系列问题,对接收机的信号捕获技术提出了全新的要求，如需处理更大的数据流,解决由二次编码带来的符号翻转和BOC调制造成的捕获多峰性问题.针对BDS-3接收机的工程实现,本文提出了一种新颖有效的两级B1C信号捕获技术.其中第一阶段采用扩展并行平均相关搜获结构,用以解决符号翻转问题,同时实现高效的信号粗捕获;第二阶段在缩小的搜索范围内进行高精度搜索,此步骤可有效避免信号多峰性造成的误锁可能.除此之外,本文还介绍了单信道和多信道组合式捕获技术,用户可根据资源占用和捕获灵敏度需求选取更有效的捕获方法.实验结果表明,本文提出的方法允许使用更小更经济的快速傅里叶变换（FFT）模块,并通过大量并行处理的方法实现快速捕获.相较传统的高精度捕获技术,此方法在采样频率超过50 MHz时,能够在保证相近的捕获精度的同时减少至少61％的运算量. 相似文献
20.
Geometry-free undifferenced, single and double differenced analysis of single frequency GPS, EGNOS and GIOVE-A/B measurements 总被引：2，自引：1，他引：2
This paper demonstrates a geometry-free GNSS measurement analysis approach and presents results of single frequency GPS, EGNOS
and GIOVE short and zero baseline measurements. The purpose is to separate the different contributions to the measurement
noise of pseudo range code and carrier phase observations at the receiver. The influence of multipath on the different combinations
of observations is also determined. Quantitative results are presented for the thermal code and phase measurement noise and
for the correlation between the observations. Comparison of the results with theoretical approximations confirms the validity
of the used approach. Results from field measurements clearly show less thermal noise on the Galileo E1BC observations than
on the GPS L1C/A observations due to the new signal modulation. The feasibility of ambiguity resolution with a geometry-free
model is also discussed including the significant impact of multipath thereon. 相似文献