Temperature coefficients of elastic constants of single crystal MgO between 80 and 1,300 K     

Yoshio Sumino  Orson L. Anderson  Isao Suzuki 《Physics and Chemistry of Minerals》1983,9(1):38-47

Elastic constants of single crystal MgO have been measured by the rectangular parallelepiped resonance (RPR) method at temperatures between 80 and 1,300 K. Elastic constants C _ij (Mbar=10³ kbar) and their temperature coefficients (kbar/K) are: $$\begin{gathered} {\text{ }}C_{{\text{11}}} {\text{ }}C_{{\text{12}}} {\text{ }}C_{{\text{44}}} {\text{ }}K_s {\text{ }}C_s \hfill \\ C_{ij} {\text{ 300 K 2}}{\text{.966 0}}{\text{.959 1}}{\text{.562 1}}{\text{.628 1}}{\text{.004}} \hfill \\ \partial C_{ij} {\text{/}}\partial T{\text{100 K }} - {\text{0}}{\text{.259 0}}{\text{.013 }} - {\text{0}}{\text{.072 }} - {\text{0}}{\text{.078 }} - {\text{0}}{\text{.136}} \hfill \\ {\text{ 300K }} - {\text{0}}{\text{.596 0}}{\text{.068 }} - {\text{0}}{\text{.122 }} - {\text{0}}{\text{.153 }} - {\text{0}}{\text{.332}} \hfill \\ {\text{ 800 K }} - {\text{0}}{\text{.619 0}}{\text{.009 }} - {\text{0}}{\text{.152 }} - {\text{0}}{\text{.200 }} - {\text{0}}{\text{.314}} \hfill \\ {\text{ 1,300 K }} - {\text{0}}{\text{.598 0}}{\text{.036 }} - {\text{0}}{\text{.130 }} - {\text{0}}{\text{.223 }} - {\text{0}}{\text{.218}} \hfill \\ \end{gathered} $$ By combining the present results with the previous data on the thermal expansivity and specific heat, the thermodynamic properties of magnesium oxide are presented and discussed. The elastic parameters of MgO at very high temperatures in the earth's lower mantle are also clarified.  相似文献   

The reversed alumina contents of orthopyroxene in equilibrium with spinel and forsterite in the system MgO-Al2O3-SiO2     

T. Gasparik  R. C. Newton 《Contributions to Mineralogy and Petrology》1984,85(2):186-196

Equilibrium alumina contents of orthopyroxene coexisting with spinel and forsterite in the system MgO-Al₂O₃-SiO₂ have been reversed at 15 different P-T conditions, in the range 1,030–1,600° C and 10–28 kbar. The present data and three reversals of Danckwerth and Newton (1978) have been modeled assuming an ideal pyroxene solid solution with components Mg₂Si₂O₆ (En) and MgAl₂SiO₆ (MgTs), to yield the following equilibrium condition (J, bar, K): $$\begin{gathered} RT{\text{ln(}}X_{{\text{MgTs}}} {\text{/}}X_{{\text{En}}} {\text{) + 29,190}} - {\text{13}}{\text{.42 }}T + 0.18{\text{ }}T + 0.18{\text{ }}T^{1.5} \hfill \\ + \int\limits_1^P {\Delta V_{T,P}^{\text{0}} dP = 0,} \hfill \\ \end{gathered} $$ where $$\begin{gathered} + \int\limits_1^P {\Delta V_{T,P}^{\text{0}} dP} \hfill \\ = [0.013 + 3.34 \times 10^{ - 5} (T - 298) - 6.6 \times 10^{ - 7} P]P. \hfill \\ \end{gathered} $$ The data of Perkins et al. (1981) for the equilibrium of orthopyroxene with pyrope have been similarly fitted with the result: $$\begin{gathered} - RT{\text{ln(}}X_{{\text{MgTs}}} \cdot X_{{\text{En}}} {\text{) + 5,510}} - 88.91{\text{ }}T + 19{\text{ }}T^{1.2} \hfill \\ + \int\limits_1^P {\Delta V_{T,P}^{\text{0}} dP = 0,} \hfill \\ \end{gathered} $$ where $$\begin{gathered} + \int\limits_1^P {\Delta V_{T,P}^{\text{0}} dP} \hfill \\ = [ - 0.832 - 8.78{\text{ }} \times {\text{ 10}}^{ - {\text{5}}} (T - 298) + 16.6{\text{ }} \times {\text{ 10}}^{ - 7} P]{\text{ }}P. \hfill \\ \end{gathered} $$ The new parameters are in excellent agreement with measured thermochemical data and give the following properties of the Mg-Tschermak endmember: $$H_{f,970}^0 = - 4.77{\text{ kJ/mol, }}S_{298}^0 = 129.44{\text{ J/mol}} \cdot {\text{K,}}$$ and $$V_{298,1}^0 = 58.88{\text{ cm}}^{\text{3}} .$$ The assemblage orthopyroxene+spinel+olivine can be used as a geothermometer for spinel lherzolites, subject to a choice of thermodynamic mixing models for multicomponent orthopyroxene and spinel. An ideal two-site mixing model for pyroxene and Sack's (1982) expressions for spinel activities provide, with the present experimental calibration, a geothermometer which yields temperatures of 800° C to 1,350° C for various alpine peridotites and 850° C to 1,130° C for various volcanic inclusions of upper mantle origin.  相似文献   

(Ca,Mg)2Si2O6 clinopyroxenes: A solution model based on nonconvergent site-disorder     

Paula M. Davidson  John Grover  Donald H. Lindsley 《Contributions to Mineralogy and Petrology》1982,80(1):88-102

Experiments at high pressure and temperature indicate that excess Ca may be dissolved in diopside. If the (Ca, Mg)₂Si₂O₆ clinopyroxene solution extends to more Ca-rich compositions than CaMgSi₂O₆, macroscopic regular solution models cannot strictly be applied to this system. A nonconvergent site-disorder model, such as that proposed by Thompson (1969, 1970), may be more appropriate. We have modified Thompson's model to include asymmetric excess parameters and have used a linear least-squares technique to fit the available experimental data for Ca-Mg orthopyroxene-clinopyroxene equilibria and Fe-free pigeonite stability to this model. The model expressions for equilibrium conditions \(\mu _{{\text{Mg}}_{\text{2}} {\text{Si}}_{\text{2}} {\text{O}}_{\text{6}} }^{{\text{opx}}} = \mu _{{\text{Mg}}_{\text{2}} {\text{Si}}_{\text{2}} {\text{O}}_{\text{6}} }^{{\text{cpx}}} \) (reaction A) and \(\mu _{{\text{Ca}}_{\text{2}} {\text{Si}}_{\text{2}} {\text{O}}_{\text{6}} }^{{\text{opx}}} = \mu _{{\text{Ca}}_{\text{2}} {\text{Si}}_{\text{2}} {\text{O}}_{\text{6}} }^{{\text{cpx}}} \) (reaction B) are given by: 1 $$\begin{gathered} \Delta \mu _{\text{A}}^{\text{O}} = {\text{RT 1n}}\left[ {\frac{{(X_{{\text{Mg}}}^{{\text{opx}}} )^2 }}{{X_{{\text{Mg}}}^{{\text{M1}}} \cdot X_{{\text{Mg}}}^{{\text{M2}}} }}} \right] - \frac{1}{2}\{ W_{21} [2(X_{{\text{Ca}}}^{{\text{M2}}} )^3 - (X_{{\text{Ca}}}^{{\text{M2}}} ] \hfill \\ {\text{ + 2W}}_{{\text{22}}} [X_{{\text{Ca}}}^{{\text{M2}}} )^2 - (X_{{\text{Ca}}}^{{\text{M2}}} )^3 + \Delta {\text{G}}_{\text{*}}^{\text{0}} (X_{{\text{Ca}}}^{{\text{M1}}} \cdot X_{{\text{Ca}}}^{{\text{M2}}} )\} \hfill \\ {\text{ + W}}^{{\text{opx}}} (X_{{\text{Wo}}}^{{\text{opx}}} )^2 \hfill \\ \Delta \mu _{\text{B}}^{\text{O}} = {\text{RT 1n}}\left[ {\frac{{(X_{{\text{Ca}}}^{{\text{opx}}} )^2 }}{{X_{{\text{Ca}}}^{{\text{M1}}} \cdot X_{{\text{Ca}}}^{{\text{M2}}} }}} \right] - \frac{1}{2}\{ 2W_{21} [2(X_{{\text{Mg}}}^{{\text{M2}}} )^2 - (X_{{\text{Mg}}}^{{\text{M2}}} )^3 ] \hfill \\ {\text{ + W}}_{{\text{22}}} [2(X_{{\text{Mg}}}^{{\text{M2}}} )^3 - (X_{{\text{Mg}}}^{{\text{M2}}} )^2 + \Delta {\text{G}}_{\text{*}}^{\text{0}} (X_{{\text{Mg}}}^{{\text{M1}}} \cdot X_{{\text{Mg}}}^{{\text{M2}}} )\} \hfill \\ {\text{ + W}}^{{\text{opx}}} (X_{{\text{En}}}^{{\text{opx}}} )^2 \hfill \\ \hfill \\ \end{gathered} $$ where 1 $$\begin{gathered} \Delta \mu _{\text{A}}^{\text{O}} = 2.953 + 0.0602{\text{P}} - 0.00179{\text{T}} \hfill \\ \Delta \mu _{\text{B}}^{\text{O}} = 24.64 + 0.958{\text{P}} - (0.0286){\text{T}} \hfill \\ {\text{W}}_{{\text{21}}} = 47.12 + 0.273{\text{P}} \hfill \\ {\text{W}}_{{\text{22}}} = 66.11 + ( - 0.249){\text{P}} \hfill \\ {\text{W}}^{{\text{opx}}} = 40 \hfill \\ \Delta {\text{G}}_*^0 = 155{\text{ (all values are in kJ/gfw)}}{\text{.}} \hfill \\ \end{gathered} $$ . Site occupancies in clinopyroxene were determined from the internal equilibrium condition 1 $$\begin{gathered} \Delta G_{\text{E}}^{\text{O}} = - {\text{RT 1n}}\left[ {\frac{{X_{{\text{Ca}}}^{{\text{M1}}} \cdot X_{{\text{Mg}}}^{{\text{M2}}} }}{{X_{{\text{Ca}}}^{{\text{M2}}} \cdot X_{{\text{Mg}}}^{{\text{M1}}} }}} \right] + \tfrac{1}{2}[(2{\text{W}}_{{\text{21}}} - {\text{W}}_{{\text{22}}} )(2{\text{X}}_{{\text{Ca}}}^{{\text{M2}}} - 1) \hfill \\ {\text{ + }}\Delta G_*^0 (X_{{\text{Ca}}}^{{\text{M1}}} - X_{{\text{Ca}}}^{{\text{M2}}} ) + \tfrac{3}{2}(2{\text{W}}_{{\text{21}}} - {\text{W}}_{{\text{22}}} ) \hfill \\ {\text{ (1}} - 2X_{{\text{Ca}}}^{{\text{M1}}} )(X_{{\text{Ca}}}^{{\text{M1}}} + \tfrac{1}{2})] \hfill \\ \end{gathered} $$ where δG _E ⁰ =153+0.023T+1.2P. The predicted concentrations of Ca on the clinopyroxene Ml site are low enough to be compatible with crystallographic studies. Temperatures calculated from the model for coexisting ortho- and clinopyroxene pairs fit the experimental data to within 10° in most cases; the worst discrepancy is 30°. Phase relations for clinopyroxene, orthopyroxene and pigeonite are successfully described by this model at temperatures up to 1,600° C and pressures from 0.001 to 40 kbar. Predicted enthalpies of solution agree well with the calorimetric measurements of Newton et al. (1979). The nonconvergent site disorder model affords good approximations to both the free energy and enthalpy of clinopyroxenes, and, therefore, the configurational entropy as well. This approach may provide an example for Febearing pyroxenes in which cation site exchange has an even more profound effect on the thermodynamic properties.  相似文献   

The combined effect of F and H2O on interdiffusion between peralkaline dacitic and rhyolitic melts     

Don R. Baker  Hélène Bossányi 《Contributions to Mineralogy and Petrology》1994,117(2):203-214

The effective binary diffusion coefficient (EBDC) of silicon has been measured during the interdiffusion of peralkaline, fluorine-bearing (1.3 wt% F), hydrous (3.3 and 6 wt% H₂O), dacitic and rhyolitic melts at 1.0 GPa and temperatures between 1100°C and 1400°C. From Boltzmann-Matano analysis of diffusion profiles the diffusivity of silicon at 68 wt% SiO₂ can be described by the following Arrhenius equations (with standard errors): $$\begin{gathered} {\text{with 1}}{\text{.3 wt\% F and 3}}{\text{.3\% H}}_{\text{2}} {\text{O:}} \hfill \\ {\text{D}}_{{\text{Si}}} = \begin{array}{*{20}c} { + {\text{3}}{\text{.59}}} \\ {{\text{3}}{\text{.66}} \times {\text{10}}^{ - {\text{9}}} } \\ { - {\text{1}}{\text{.86}}} \\ \end{array} {\text{exp}}\left( {{{ - {\text{86}}{\text{.1}} \pm {\text{8}}{\text{.9}}} \mathord{\left/ {\vphantom {{ - {\text{86}}{\text{.1}} \pm {\text{8}}{\text{.9}}} {{\text{RT}}}}} \right. \kern-\nulldelimiterspace} {{\text{RT}}}}} \right) \hfill \\ {\text{with 1}}{\text{.3 wt\% F and 6}}{\text{.0\% H}}_{\text{2}} {\text{O:}} \hfill \\ {\text{D}}_{{\text{Si}}} = \begin{array}{*{20}c} { + {\text{3}}{\text{.59}}} \\ {{\text{3}}{\text{.51}} \times {\text{10}}^{ - {\text{8}}} } \\ { - {\text{1}}{\text{.77}}} \\ \end{array} {\text{exp}}\left( {{{ - {\text{109}}{\text{.5}} \pm {\text{8}}{\text{.9}}} \mathord{\left/ {\vphantom {{ - {\text{109}}{\text{.5}} \pm {\text{8}}{\text{.9}}} {{\text{RT}}}}} \right. \kern-\nulldelimiterspace} {{\text{RT}}}}} \right) \hfill \\ \end{gathered} $$ where D is in m²s^?1 and activation energies are in kJ/mol. Diffusivities measured at 64 and 72 wt% SiO₂ are only slightly different from those at 68 wt% SiO₂ and frequently all measurements are within error of each other. Silicon, aluminum, iron, magnesium, and calcium EBDCs were also calculated from diffusion profiles by error function inversion techniques assuming constant diffusivity. With one exception, silicon EBDCs calculated by error function techniques are within error of Boltzmann-Matano EBDCs. Average diffusivities of Fe, Mg, and Ca were within a factor of 2.5 of silicon diffusivities whereas Al diffusivities were approximately half those of silicon. Alkalies diffused much more rapidly than silicon and non-alkalies, however their diffusivities were not quantitatively determined. Low activation energies for silicon EBDCs result in rapid diffusion at magmatic temperatures. Assuming that water and fluorine exert similar effects on melt viscosity at high temperatures, the viscosity can be calculated and used in the Eyring equation used to determine diffusivities, typically to within a factor of three of those measured in this study. This correlation between viscosity and diffusivity can be inverted to calculate viscosities of fluorine- and water-bearing granitic melts at magmatic temperatures; these viscosities are orders of magnitude below those of hydrous granitic melts and result in more rapid and effective separation of granitic magmas from partially molten source rocks. Comparison of Arrhenius parameters for diffusion measured in this study with Arrhenius parameters determined for diffusion in similar compositions at the same pressure demonstrates simple relationships between Arrhenius parameters, activation energy-E_a, kJ/mol, pre-exponential factor-D_o, m²s^?1, and the volatile, X=F or OH^?, to oxygen, O, ratio of the melt {(X/X+O)}: $$\begin{gathered} {\text{E}}a = - {\text{1533\{ }}{{\text{X}} \mathord{\left/ {\vphantom {{\text{X}} {\left( {{\text{X}} + {\text{O}}} \right)}}} \right. \kern-\nulldelimiterspace} {\left( {{\text{X}} + {\text{O}}} \right)}}{\text{\} }} + {\text{213}}{\text{.3}} \hfill \\ {\text{D}}_{\text{O}} = {\text{2}}{\text{.13}} \times {\text{10}}^{ - {\text{6}}} {\text{exp}}\left[ { - {\text{6}}{\text{.5\{ }}{{\text{X}} \mathord{\left/ {\vphantom {{\text{X}} {\left( {{\text{X}} + {\text{O}}} \right)}}} \right. \kern-\nulldelimiterspace} {\left( {{\text{X}} + {\text{O}}} \right)}}{\text{\} }}} \right] \hfill \\ \end{gathered} $$ These relationships can be used to estimate diffusion in various melts of dacitic to rhyolitic composition containing both fluorine and water. Calculations for the contamination of rhyolitic melts by dacitic enclaves at 800°C and 700°C provide evidence for the virtual inevitability of diffusive contamination in hydrous and fluorine-bearing magmas if they undergo magma mixing of any form.  相似文献   

The reaction garnet+clinopyroxene+quartz =2 orthopyroxene+anorthite: A potential geobarometer for granulites     

P. Paria  A. Bhattacharya  S. K. Sen 《Contributions to Mineralogy and Petrology》1988,99(1):126-133

A mineralogic geobarometer based on the reaction garnet+clinopyroxene+quartz=2 orthopyroxene+anorthite is proposed. The geobarometric formulations for the Fe- and Mg- end member equilibria are $$\begin{gathered} P_{({\text{Fe}})} {\text{ }}({\text{bars}}){\text{ = 32}}{\text{.097 }}T{\text{ }} - {\text{ 26385 }} - {\text{ 22}}{\text{.79 (}}T - 848 - T1{\text{n(}}T/848{\text{))}} \hfill \\ {\text{ }} - (3.655 + 0.0138T){\text{ }}\left( {\frac{{{\text{(}}T - 848{\text{)}}^{\text{2}} }}{T}} \right) \hfill \\ {\text{ }} - {\text{(3}}{\text{.123) }}T1{\text{n }}\frac{{(a_{a{\text{n}}}^{{\text{Plag}}} )(a_{{\text{fs}}}^{{\text{P}}\ddot u{\text{x}}} )^2 }}{{(a_{{\text{alm}}}^{{\text{Gt}}} )(a_{{\text{hed}}}^{{\text{Opx}}} )}} \hfill \\ P_{({\text{Mg}})} {\text{ (bars) = 9}}{\text{.270 }}T + 4006 - 0.9305{\text{ }}(T - 848 - T1{\text{n (}}T/848{\text{)}}) \hfill \\ {\text{ }} - (1.1963{\text{ }} - {\text{ }}6.0128{\text{ x 10}}^{ - {\text{3}}} T)\left( {\frac{{(T - 848)^2 }}{T}} \right) \hfill \\ {\text{ }} - 3.489{\text{ }}T1{\text{n }}\frac{{(a_{an}^{{\text{Plag}}} ){\text{ }}(a_{{\text{ens}}}^{{\text{Opx}}} )}}{{{\text{(}}a_{{\text{pyr}}}^{{\text{Gt}}} {\text{) (}}a_{{\text{diop}}}^{{\text{Cpx}}} {\text{)}}}}. \hfill \\ \end{gathered}$$ The end member thermodynamic data have been taken from the data base of Helgeson et al. (1978) and Saxena and Erikson (1983). The activities of pyroxene components and anorthite in plagioclase have been modelled after Wood and Banno (1973) and Newton (1983) respectively. The activities of pyrope and almandine are calculated from the binary interaction parameters for garnet solid solutions proposed by Saxena and Erikson (1983). Pressures computed from these equations for fifty sets of published mineral data from several granulite areas are comparable with those obtained from dependable geobarometers. The pressure values determined from the Fe-end member equilibrium appear to be more reasonable than those from the Mg-end member reaction. It is likely that the difference in pressures computed from the Fe- and Mg-end members, ΔP ^*, have been caused by non-ideal mixing in the phases, especially in garnets.  相似文献   

Non-ideal mixing in the phlogopite-annite binary: constraints from experimental data on Mg−Fe partitioning and a reformulation of the biotite-garnet geothermometer     

A. Bhattacharya  L. Mohanty  A. Maji  S. K. Sen  M. Raith 《Contributions to Mineralogy and Petrology》1992,111(1):87-93

The existing experimental data [Ferry and Spear 1978; Perchuk and Lavrent'eva 1983] on Mg?Fe partitioning between garnet and biotite are disparate. The underlying assumption of ideal Mg?Fe exchange between the minerals has been examined on the basis of recently available thermochemical data. Using the updated mixing parameters for the pyrope-almandine asymmetric regular solution as inputs [Ganguly and Saxena 1984; Hackler and Wood 1984], thermodynamic analysis points to non-ideal mixing in the phlogopite-annite binary in the temperature range of 550°C–950°C. The non-ideality can be approximated by a temperature-independent, one constant Margules parameter. The retrieved values for enthalpy of mixing for Mg?Fe biotites and the standard state enthalpy and entropy changes of the exchange reaction were combined with existing thermochemical data on grossular-pyrope and grossular-almandine binaries to obtain geothermometric expressions for Mg?Fe fractionation between biotite and garnet. [T in K] $$\begin{gathered} {\text{T(HW) = [20286 + 0}}{\text{.0193P - \{ 2080(X}}_{{\text{Mg}}}^{{\text{Gt}}} {\text{)}}^{\text{2}} {\text{ - 6350(X}}_{{\text{Fe}}}^{{\text{Gt}}} {\text{)}}^{\text{2}} \hfill \\ {\text{ - 13807(X}}_{{\text{Ca}}}^{{\text{Gt}}} {\text{)(1 - X}}_{{\text{Mn}}}^{{\text{Gt}}} {\text{) + 8540(X}}_{{\text{Fe}}}^{{\text{Gt}}} {\text{)(X}}_{{\text{Mg}}}^{{\text{Gt}}} {\text{)(1 - X}}_{{\text{Mn}}}^{{\text{Gt}}} {\text{)}} \hfill \\ {\text{ + 4215(X}}_{{\text{Ca}}}^{{\text{Gt}}} {\text{)(X}}_{{\text{Mg}}}^{{\text{Gt}}} {\text{ - X}}_{{\text{Fe}}}^{{\text{Gt}}} {\text{)\} + 4441}}{{{\text{(2X}}_{{\text{Mg}}}^{{\text{Bt}}} {\text{ - 1)]}}} \mathord{\left/ {\vphantom {{{\text{(2X}}_{{\text{Mg}}}^{{\text{Bt}}} {\text{ - 1)]}}} {{\text{[13}}{\text{.138}}}}} \right. \kern-\nulldelimiterspace} {{\text{[13}}{\text{.138}}}} \hfill \\ {\text{ + 8}}{\text{.3143 InK}}_{\text{D}} {\text{ + 6}}{\text{.276(X}}_{{\text{Ca}}}^{{\text{Gt}}} ){\text{(1 - X}}_{{\text{Mn}}}^{{\text{Gt}}} )] \hfill \\ {\text{T(GS) = [13538 + 0}}{\text{.0193P - \{ 837(X}}_{{\text{Mg}}}^{{\text{Gt}}} )^{\text{2}} {\text{ - 10460(X}}_{{\text{Fe}}}^{{\text{Gt}}} )^2 \hfill \\ {\text{ - 13807(X}}_{{\text{Ca}}}^{{\text{Gt}}} )(1{\text{ - X}}_{{\text{Mn}}}^{{\text{Gt}}} {\text{) + 19246(X}}_{{\text{Fe}}}^{{\text{Gt}}} ){\text{(X}}_{{\text{Mg}}}^{{\text{Gt}}} ){\text{(1 - X}}_{{\text{Mn}}}^{{\text{Gt}}} ) \hfill \\ {\text{ }}{{{\text{ + 5649(X}}_{{\text{Ca}}}^{{\text{Gt}}} ){\text{(X}}_{{\text{Mg}}}^{{\text{Gt}}} {\text{ - X}}_{{\text{Fe}}}^{{\text{Gt}}} ){\text{\} + 7972(2X}}_{{\text{Mg}}}^{{\text{Bt}}} {\text{ - 1)]}}} \mathord{\left/ {\vphantom {{{\text{ + 5649(X}}_{{\text{Ca}}}^{{\text{Gt}}} ){\text{(X}}_{{\text{Mg}}}^{{\text{Gt}}} {\text{ - X}}_{{\text{Fe}}}^{{\text{Gt}}} ){\text{\} + 7972(2X}}_{{\text{Mg}}}^{{\text{Bt}}} {\text{ - 1)]}}} {{\text{[6}}{\text{.778}}}}} \right. \kern-\nulldelimiterspace} {{\text{[6}}{\text{.778}}}} \hfill \\ {\text{ + 8}}{\text{.3143InK}}_{\text{D}} {\text{ + 6}}{\text{.276(X}}_{{\text{Ca}}}^{{\text{Gt}}} )(1{\text{ - X}}_{{\text{Mn}}}^{{\text{Gt}}} )] \hfill \\ \end{gathered} $$ The reformulated geothermometer is an improvement over existing biotite-garnet geothermometers because it reconciles the experimental data sets on Fe?Mg partitioning between the two phases and is based on updated activity-composition relationship in Fe?Mg?Ca garnet solid solutions.  相似文献   

Intrinsic oxygen Fugacity measurements on chromites from the Bushveld Complex and their petrogenetic significance     

Rolf Snethlage  Dietrich D. Klemm 《Contributions to Mineralogy and Petrology》1978,67(2):127-138

Oxygen Fugacity measurements were carried out on chromites from the Eastern Bushveld Complex (Maandagshoek) and are compared with former measurements on chromites from the western Bushveld Complex (Zwartkop Chrome Mine). These results together with those of Hill and Roeder (1974) yield the following conditions of formation for the massive chromitite layers: Western Bushveld Complex (Zwartkop Chrome Mine) $$\begin{gathered} Layer{\text{ }}T(^\circ C) p_{O_2 } (atm) \hfill \\ LG3{\text{ 1160}} - {\text{1234 10}}^{ - {\text{5}}} - 10^{ - 7.6} \hfill \\ LG4{\text{ 1175}} - {\text{1200 10}}^{ - 6.35} - 10^{ - 7.20} \hfill \\ LG6{\text{ 1162}} - {\text{1207 10}}^{ - 6.20} - 10^{ - 7.50} \hfill \\ \hfill \\ \end{gathered} $$ Eastern Bushveld Complex (Farm Maandagshoek) $$\begin{gathered} {\text{LXI 1115}} - {\text{1150 10}}^{ - 7.80} - 10^{ - 8.80} \hfill \\ ( = {\text{Steelpoort Seam)}} \hfill \\ {\text{LX 1125 10}}^{ - 8.25} \hfill \\ {\text{V 1120 10}}^{ - 8.55} \hfill \\ {\text{LII 1120 10}}^{ - 8.0} - 10^{ - 8.60} \hfill \\ \end{gathered} $$ The comparison of the data shows, that the chronitite layers within each particular sequence were formed under approximately identicalp _{o 2}- andT-conditions. The chromites from the western Bushveld Complex, however, were formed at higher temperatures and higher oxygen fugacities than the chromites from the eastern Bushveld Complex. Fromp _{o 2}-T-curves of disseminated chromites and the temperatures derived above, the following conditions of formation for the host rocks were obtained: Western Bushveld Complex $$T = 1200^\circ {\text{C; }}p_{{\text{o}}_{\text{2}} } = 10^{ - 7.25} - 10^{ - 7.50} $$ Eastern Bushveld Complex $$T = 1125^\circ {\text{C; }}p_{{\text{o}}_{\text{2}} } = 10^{ - 8.50} - 10^{ - 9.25} $$ Consequently, the host rocks in the Zwartkop-Chrome-Mine, were formed under higher temperatures and higher oxygen fugacities than the host rocks at Maandagshoek. The rock sequence in the Zwartkop-Chrome-Mine therefore originated in an earlier stage of the differentiation of the Bushveld magma. Comparison of the chromites from the host rocks with the chromites from massive layers supports Ulmer's (1969) thesis that an increase of the oxygen fugacity is responsible for the formation of massive chromitite layers. The values in this investigation show that increases of only about 0.5–1.0 log units are necessary to enhance chromitite layer formation.  相似文献   

Dislocation-assisted diffusion of oxygen in albite     

R. A. Yund  B. M. Smith  J. Tullis 《Physics and Chemistry of Minerals》1981,7(4):185-189

Oxygen diffusion in albite has been determined by the integrating (bulk ¹⁸O) method between 750° and 450° C, for a P _H2O of 2 kb. The original material has a low dislocation density (<10⁶ cm^?2), and its lattice diffusion coefficient (D ₁), given below, agrees well with previous determinations. A sample was deformed at high temperature and pressure to produce a uniform dislocation density of 5 × 10⁹ cm^?2. The diffusion coefficient (D _a) for this deformed material, given below, is about 0.5 and 0.7 orders of magnitude larger than D ₁ at 700° and 450° C, respectively. This enhancement is believed due to faster diffusion along the cores of dislocations. Assuming a dislocation core radius of 4 Å, the calculated pipe diffusion coefficient (D _p), given below, is about 5 orders of magnitude larger than D ₁. These results suggest that volume diffusion at metamorphic conditions may be only slightly enhanced by the presence of dislocations. $$\begin{gathered} D_1 = 9.8 \pm 6.9 \times 10^{ - 6} (cm^2 /\sec ) \hfill \\ {\text{ }} \cdot \exp [ - 33.4 \pm 0.6(kcal/mole)/RT] \hfill \\ \end{gathered} $$ $$\begin{gathered} D_a = 7.6 \pm 4.0 \times 10^{ - 6} (cm^2 /\sec ) \hfill \\ {\text{ }} \cdot \exp [ - 30.9 \pm 1.1(kcal/mole)/RT] \hfill \\ \end{gathered} $$ $$\begin{gathered} D_p \approx 1.2 \times 10^{ - 1} (cm^2 /\sec ) \hfill \\ {\text{ }} \cdot \exp [ - 29.8(kcal/mole)/RT]. \hfill \\ \end{gathered} $$   相似文献   

The system Fe-Si-O: Oxygen buffer calibrations to 1,500K   总被引：1，自引：0，他引：1  

J. Myers  H. P. Eugster 《Contributions to Mineralogy and Petrology》1983,82(1):75-90

The five solid-phase oxygen buffers of the system Fe-Si-O, iron-wuestite (IW), wuestite-magnetite (WM), magnetite-hematite (MH), quartz-iron-fayalite (QIF) and fayalite-magnetite-quartz (FMQ) have been recalibrated at 1 atm pressure and temperatures from 800°–1,300° C, using a thermogravimetric gas mixing furnace. The oxygen fugacity, \(f_{{\text{O}}_{\text{2}} }\) was measured with a CaO-doped ZrO₂ electrode. Measurements were made also for wuestite solid solutions in order to determine the redox behavior of wuestites with O/Fe ratios varying from 1.05 to 1.17. For FMQ, additional determinations were carried out at 1 kb over a temperature range of 600° to 800° C, using a modified Shaw membrane. Results agree reasonably well with published data and extrapolations. The reaction parameters K, ΔG _r ^o , ΔH _r ^o , and ΔS _r ^o were calculated from the following log \(f_{{\text{O}}_{\text{2}} }\) /T relations (T in K): $$\begin{gathered} {\text{IW }}\log f_{{\text{O}}_{\text{2}} } = - 26,834.7/T + 6.471\left( { \pm 0.058} \right) \hfill \\ {\text{ }}\left( {{\text{800}} - 1,260{\text{ C}}} \right), \hfill \\ {\text{WM }}\log f_{{\text{O}}_{\text{2}} } = - 36,951.3/T + 16.092\left( { \pm 0.045} \right) \hfill \\ {\text{ }}\left( {{\text{1,000}} - 1,300{\text{ C}}} \right), \hfill \\ {\text{MH }}\log f_{{\text{O}}_{\text{2}} } = - 23,847.6/T + 13.480\left( { \pm 0.055} \right) \hfill \\ {\text{ }}\left( {{\text{1,040}} - 1,270{\text{ C}}} \right), \hfill \\ {\text{QIF }}\log f_{{\text{O}}_{\text{2}} } = - 27,517.5/T + 6.396\left( { \pm 0.049} \right) \hfill \\ {\text{ }}\left( {{\text{960}} - 1,140{\text{ C}}} \right), \hfill \\ {\text{FMQ }}\log f_{{\text{O}}_{\text{2}} } = - 24,441.9/T + 8.290\left( { \pm 0.167} \right) \hfill \\ {\text{ }}\left( {{\text{600}} - 1,140{\text{ C}}} \right). \hfill \\ \end{gathered}$$ These experimentally determined reaction parameters were combined with published 298 K data to determine the parameters G_f, H_f, and S_f for the phases wuestite, magnetite, hematite, and fayalite from 298 K to the temperatures of the experiments. The T? \(f_{{\text{O}}_{\text{2}} }\) data for wuestite solid solutions were used to obtain activities, excess free energies and Margules mixing parameters. The new data provide a more reliable, consistent and complete reference set for the interpretation of redox reactions at elevated temperatures in experiments and field settings encompassing the crust, mantle and core as well as extraterrestrial environments.  相似文献   

The variation of tetrahedral bond lengths in sodic plagioclase feldspars     

Michael W. Phillips  Paul H. Ribbe 《Contributions to Mineralogy and Petrology》1973,39(4):327-339

Multiple linear regression analysis has been applied to the geometric and chemical variables in sodic plagioclases in order to determine their relative effects on individual T-O bond lengths in the Al_1+xSi_3?xO₈ tetrahedral framework. Using data from crystal structure analyses of low and high albite, An₁₆ and An₂₈, and assuming that low albite is completely ordered, 1 $$\begin{gathered} {\text{T}} - {\text{O = 1}}{\text{.568}} + {\text{[(0}}{\text{.122) x (Al content of the T site)]}} \hfill \\ {\text{ }} - {\text{[(0}}{\text{.037) x (}}\Delta {\text{{\rm A}l}}_{{\text{br}}} )] + [0.063){\text{ x }}(\Sigma {\text{[}}q{\text{/(Na,Ca}} - {\text{O)}}^{\text{2}} ])] \hfill \\ {\text{ }} + {\text{[(0}}{\text{.029) x (}} - {\text{1/cosT}} - {\text{O}} - {\text{T)]}} \hfill \\ \end{gathered}$$ where the Al content of a particular tetrahedral (T) site can be estimated from empirically-derived determinative curves, where Δ Al_br is a linkage factor to account for the Al content of adjacent tetrahedral sites, where the formal charge on the (Na_1?xCa_x) atom is q=1+x, and where T-O-T is the inter-tetrahedral angle involving the T-O bond. For sodic plagioclases it is essential to know only the anorthite content and the 2Θ₁₃₁-2Θ_1¯31 spacing (CuK _α radiation) in order to determine the independent variables in this equation and thus to evaluate the individual T-O distances. The 64 individual T-O distances predicted for the four sodic plagioclases by this equation agree well with the observed T-O bond lengths (σ=0.004 Å; r=0.994), and the method has been used by way of example to rationalize the T-O bond lengths in analcime (cf. Ferraris, Jones and Yerkess, 1972).  相似文献   

Thermodynamic mixing properties of Mg(Al,Cr)2O4 spinel crystalline solution at high temperatures and pressures     

Yastami Oka  Petra Steinke  Niranjan D. Chatterjee 《Contributions to Mineralogy and Petrology》1984,87(2):196-204

Three Al-Cr exchange isotherms at 1,250°, 1,050°, and 796° between Mg(Al, Cr)₂O₄ spinel and (Al, Cr)₂O₃ corundum crystalline solutions have been studied experimentally at 25 kbar pressure. Starting from gels of suitable bulk compositions, close approach to equilibrium has been demonstrated in each case by time studies. Using the equation of state for (Al, Cr)₂O₃ crystalline solution (Chatterjee et al. 1982a) and assuming that the Mg(Al, Cr)₂O₄ can be treated in terms of the asymmetric Margules relation, the exchange isotherms were solved for Δ G ^*, and . The best constrained data set from the 1,250° C isotherm clearly shows that the latter two quantities do not overlap within three standard deviations, justifying the choice of asymmetric Margules relation for describing the excess mixing properties of Mg(Al, Cr)₂O₄ spinels. Based on these experiments, the following polybaric-polythermal equation of state can be formulated: , P expressed in bars, T in K, G _m ^ex and W _G,i ^Sp in joules/mol. Temperature-dependence of G _m ^ex is best constrained in the range 796–1,250° C; extrapolation beyond that range would have to be done with caution. Such extrapolation to lower temperature shows tentatively that at 1 bar pressure the critical temperature, T _c, of the spinel solvus is 427° C, with dT_c/dP≈1.3 K/kbar. The critical composition, X _c, is 0.42 , and changes barely with pressure. Substantial error in calculated phase diagrams will result if the significant positive deviation from ideality is ignored for Al-Cr mixing in such spinels.  相似文献   

Experimental study of Fe-Mg distribution between biotite and orthopyroxene at P=490 MPa     

V. I. Fonarev  A. N. Konilov 《Contributions to Mineralogy and Petrology》1986,93(2):227-235

Partitioning of Mg and Fe between coexisting biotite and orthopyroxene has been experimentally determined at temperatures 700, 750 and 800° C and 490 MPa total pressure in the system KAlO₂-MgO-FeO-SiO₂-H₂O. Oxygen fugacity was controlled by the QFM buffer. Starting materials were synthetic minerals of differing Fe/(Fe+Mg) values. Run products were analyzed for partitioning of components by a microprobe. Orthopyroxene was established to be notably inhomogeneous, whereas biotite was essentially homogeneous. To establish equilibrium relations, statistical treatment of the results of each experiment in addition to the whole complex of experimental data was applied. The regression equations for isotherms of the Fe-Mg partitioning between the minerals studied have been obtained. As a result, the equation for a two-dimensional regression may be written as: $$\begin{gathered} Y = (A + A_1 t + A_2 t^2 )(X - X^4 ) + (B + B_1 t + B_1 t^2 )(X^2 - X^4 ) + \hfill \\ (C + C_1 t + C_1 t^2 )(X^3 - X^4 ) + X^4 {\text{ where }}Y = X_{{\text{Opx}}}^{{\text{Fe}}} ;{\text{ X}} = {\text{X}}_{{\text{Bi}}}^{{\text{Fe}}} ; \hfill \\ t = 1000/T,K, \hfill \\ \begin{array}{*{20}c} {A = {\text{ }}4.59398,} & {A_1 = - {\text{ }}8.29838,} & {A_2 = {\text{ }}4.97316,} \\ {B = - 11.13731,} & {B_1 = {\text{ }}28.19304,} & {B_2 = - 20.98240,} \\ {A = {\text{ }}8.25072,} & {C_1 = - 20.80485,} & {C_2 = {\text{ }}15.35967} \\ \end{array} \hfill \\ {\text{ }}\sigma = 0.0143{\text{ }} \hfill \\ \end{gathered}$$ . This equation enables extrapolation of partitioning isotherms over a wide range of temperatures.  相似文献   

The carbon dioxide solubility in alkali basalts: an experimental study   总被引：1，自引：1，他引：0  

Priscille Lesne  Bruno Scaillet  Michel Pichavant  Jean-Michel Beny 《Contributions to Mineralogy and Petrology》2011,162(1):153-168

Experiments were conducted to determine CO₂ solubilities in alkali basalts from Vesuvius, Etna and Stromboli volcanoes. The basaltic melts were equilibrated with nearly pure CO₂ at 1,200°C under oxidizing conditions and at pressures ranging from 269 to 2,060 bars. CO₂ solubility was determined by FTIR measurements. The results show that alkalis have a strong effect on the CO₂ solubility and confirm and refine the relationship between the compositional parameter Π devised by Dixon (Am Mineral 82:368–378, 1997) and the CO₂ solubility. A general thermodynamic model for CO₂ solubility in basaltic melts is defined for pressures up to 2 kbars. Based on the assumption that O²⁻ and CO₃²⁻ mix ideally, we have:

_boxclose_3^2 - ^m (P,T)X_^2 - ^m f__2 (P,T) K(P,T) = X__3^2 - ^m (P,T) ( X_^2 - ^m f__2 (P,T) ). \begin{gathered} K(P,T) = {\frac{{X_{{{\text{CO}}_{3}^{2 - } }}^{m} (P,T)}}{{X_{{{\text{O}}^{2 - } }}^{m} \times f_{{{\text{CO}}_{2} }} (P,T)}}} \hfill \\ K(P,T) = {{X_{{{\text{CO}}_{3}^{2 - } }}^{m} (P,T)} \mathord{\left/ {\vphantom {{X_{{{\text{CO}}_{3}^{2 - } }}^{m} (P,T)} {\left( {X_{{{\text{O}}^{2 - } }}^{m} \times f_{{{\text{CO}}_{2} }} (P,T)} \right).}}} \right. \kern-\nulldelimiterspace} {\left( {X_{{{\text{O}}^{2 - } }}^{m} \times f_{{{\text{CO}}_{2} }} (P,T)} \right).}} \hfill \\ \end{gathered}  相似文献    14. A thermodynamic formulation of hydrous cordierite      J. William Carey 《Contributions to Mineralogy and Petrology》1995,119(2-3):155-165 A thermodynamic formulation of hydrous Mg-cordierite (Mg2Al4Si5O18·nH2O) has been obtained by application of calorimetric and X-ray diffraction data for hydrous cordierite to the results of hydrothermal syntheses. The data include measurements of the molar heat capacity and enthalpy of hydration and the molar volume. The synthesis data are consistent with a thermodynamic formulation in which H2O mixes ideally on a single crystallographic site in hydrous cordierite. The standard molar Gibbs free energy of hydration is-9.5±1.0 kJ/mol (an average of 61 syntheses). The standard molar entropy of hydration derived from this value is-108±3 J/mol-K. An equation providing the H2O content of cordierite as a function of temperature and fugacity of H2O is as follows (n moles of H2O per formula unit, n<1): $$\begin{gathered}n = {{f_{{\text{ H}}_{\text{2}} O}^{\text{V}} } \mathord{\left/{\vphantom {{f_{{\text{ H}}_{\text{2}} O}^{\text{V}} } {\left( {f_{{\text{ H}}_{\text{2}} O}^{\text{V}} + {\text{exp}}\left[ { - {\text{3}}{\text{.8389}} - 5025.2\left( {\frac{1}{T} - \frac{1}{{298.15}}} \right)} \right.} \right.}}} \right.\kern-\nulldelimiterspace} {\left( {f_{{\text{ H}}_{\text{2}} O}^{\text{V}} + {\text{exp}}\left[ { - {\text{3}}{\text{.8389}} - 5025.2\left( {\frac{1}{T} - \frac{1}{{298.15}}} \right)} \right.} \right.}} \hfill \\{\text{ }}\left. {\left. { - {\text{ln}}\left( {\frac{T}{{{\text{298}}{\text{.15}}}}} \right) - \left( {\frac{{298.15}}{T} - 1} \right)} \right]} \right) \hfill \\\end{gathered}$$ Application of this formulation to the breakdown reaction of Mg-cordierite to an assemblage of pyrope-sillimanite-quartz±H2O shows that cordierite is stabilized by 3 to 3.5 kbar under H2O-saturated conditions. The thermodynamic properties of H2O in cordierite are similar to those of liquid water, with a standard molar enthalpy and Gibbs free energy of hydration that are the same (within experimental uncertainty) as the enthalpy and Gibbs free energy of vaporization. By contrast, most zeolites have Gibbs free energies of hydration two to four times more negative than the corresponding value for the vaporization of water.  相似文献    15. Moon—An albite depleted giant Skaergaard?      Surendra K. Saxena  Alan Benimoff  Nicholas E. Pingitore Jr. 《Contributions to Mineralogy and Petrology》1977,60(1):77-90 The chemical composition of 2188 terrestrial igneous rocks ranging from ultrabasic to granitic composition was analyzed statistically using the method of factor analysis (principal components). The resultant first and second factors were: $$\begin{gathered} {\text{ }}F_1 = 0.933{\text{ Na}}_{\text{2}} {\text{O + 0}}{\text{.143 SiO}}_{\text{2}} + 0.206{\text{ K}}_{\text{2}} {\text{O}} - 0.346{\text{ CaO}} - 0.263{\text{ MgO}} - \hfill \\ .203{\text{ FeO}} \pm \cdot \cdot \cdot \hfill \\ {\text{ }}F_2 = 0.979{\text{ Al}}_{\text{2}} {\text{O}}_{\text{3}} - 0.269{\text{ MgO}} - 0.151{\text{ SiO}}_{\text{2}} - 0.112{\text{ FeO}} \pm \cdot \cdot \cdot \hfill \\ \end{gathered} $$ where oxides are in weight percent. A plot of the first factor against the second results in a useful igneous variation diagram. When the compositions of the 2188 terrestrial rocks and 604 lunar rocks are plotted on this diagram, the two groups of rocks are clearly separated within an albite-anorthite-forsterite-fayalite-quartz polygon. None of the terrestrial differentiation trends are significant for lunar rocks. The major difference in the chemistry of lunar and terrestrial rocks lies in the former being albite poor. Removal of most of the albite from the compositions of terrestrial layered intrusives such as the Skaergaard results in an excellent match between the compositions of the two groups of rocks. Albite subtracted compositions of Skaergaard rocks in particular cover the entire range of chemical variation in the lunar rocks. The statistical results prompt us to speculate further on the similarity of the moon and Skaergaard. We note that the average composition of the moon (Wanke et al., 1974) is similar to the albite subtracted composition of the Skaergaard magma. The lunar crust and a significant part of the lunar interior may match the albite subtracted and somewhat Mg enriched Skaergaard magma.  相似文献    16. Burial metamorphism of a Cretaceous volcanic sequence west from Santiago,Chile      B. Levi 《Contributions to Mineralogy and Petrology》1969,24(1):30-49 This report is a petrographic study of alteration phenomena in an area of 100 km2 in the Coastal Range west of Santiago. The stratified sequence of the area is of Cretaceous age and belongs to the western monoclinal limb of the Andean Geosyncline. Two structural units are present, separated by an angular unconformity. The older is about 9,000 m thick, and the younger 300 m thick. The rock types are mostly altered andesitic flows and flow breccias, and keratophyric ignimbrites and lavas, with alternating marine, brackish-water and terrestrial interbeds. Stratified rocks are cut locally by acid and basic apophyses and dikes, probably feeders of their volcanic host rocks. Discordant Cretaceous granitic plutons intrude the older unit. Throughout the whole stratigraphic section there are alteration minerals, which selectively replace the primary minerals, or fill amygdules and open fractures, or form a cement in flows, dikes and sedimentary interbeds. Patterns of alteration are regular and persistent; they correlate on a large scale with stratigraphic level and on a smaller scale with position within each individual flow and situation within amygdules. The stratigraphically controlled pattern is as follows: $$\begin{gathered} 1.{\text{ Younger unit}}{\text{.}} \hfill \\ {\text{ }}\left. \begin{gathered} {\text{Lower portion: 30m: albite}}---{\text{pistacite}}---{\text{actinolite}}---{\text{chlorite}}---{\text{ }} \hfill \\ {\text{calcite}}---{\text{sphene}}---{\text{quartz}} \hfill \\ \end{gathered} \right\}{\text{greenschist facies}} \hfill \\ {\text{2}}{\text{. Older unit}}{\text{.}} \hfill \\ {\text{ }}\left. \begin{gathered} {\text{a) 0}}---{\text{1,280 m : albite}}---{\text{pumpellyite}}---{\text{prehnite}}---{\text{calcite}}---{\text{chlorite}}---{\text{ }} \hfill \\ {\text{ laumontite}} \hfill \\ {\text{b) 1,280}}---{\text{4,850 m: albite}}---{\text{adularia}}---{\text{calcite}}---{\text{prehnite}}---{\text{pumpellyite}}--- \hfill \\ {\text{pistacite}}---{\text{white mica}}---{\text{quartz}} \hfill \\ {\text{c) 4,850}}---{\text{8,110 m: albite}}---{\text{pistacite}}---{\text{quartz}}---{\text{chlorite}}---{\text{calcite}}--- \hfill \\ {\text{white mica}}---{\text{sphene}}---{\text{adularia prehnite}}---{\text{pumpellyite}} \hfill \\ \end{gathered} \right\}{\text{prehnite}}---{\text{pumpellyite facies}} \hfill \\ {\text{ d) 8,110}}---{\text{9,060 m: albite}}---{\text{pistacite}}---{\text{actinolite}}---{\text{sphene}}---{\text{calcite \} greenschist facies}} \hfill \\ \end{gathered} $$ The pattern of alteration in the older unit is comparable to that described for burial metamorphosed sequences in New Zealand and Australia. Reappearence of the greenschist facies at a higher level in the younger unit poses a problem for which several explanations are possible. The smaller scale pattern of alteration shows a persistent tendency —not without exception — for the “grade” of the alteration assemblage (as correlated with depth on the large scale) to increase: from the base of the flow (non-amygdaloidal part) upward (amygdaloidal part), and from the rim of each amygdule inward. Also recognizable on the scale of a single flow is a tendency for upward increase in: a) extent of alteration (the basal zone may be fresh andesite), and b) weight percent of Na2O, K2O (with complementary depletion in CaO), and of Fe2O3/FeO. Preliminary observations indicate that this alteration pattern persists for at least 400 km north of the area here described in rocks of similar lithology and age. It is unrelated to local granitic plutons.  相似文献    17. Inverted high-temperature quartz      M. S. Ghiorso  I. S. E. Carmichael  L. K. Moret 《Contributions to Mineralogy and Petrology》1979,68(3):307-323 Fifty-two samples of inverted high-temperature quartz from volcanic rocks were investigated by Guinier-Jago powder diffractometry and differential scanning calorimetry (DSC). Quartz megacrysts from Clear Lake and Cinder Cone, California show a variability of ?2.5 ° K in their α-β transition temperature (T α-β). Quartz phenocrysts and quartz from crystalline rocks give a range of 0.5 ° K in T α-β. Neutron activation analysis of single crystals demonstrates that Al is the principal impurity (17–380 ppm). Its concentration is inversely correlated with T α-β. A very small variation was found in the a and c lattice parameters among the specimens of volcanic quartz studied. This variation does not correlate with Al content or transition temperature. Mean values at 22 ° C (a=4.1934±0.0004 Å, c=5.4046±0.0006 Å) are similar to those of quartz grown at low temperatures. Enthalpy of the α-β transition (ΔH α-β), obtained over 9.0 ° from DSC runs, is dependent upon sample grain size and for a crushed powder with zero hysteresis (T α-β on heating=T α-β on cooling) is 92.0 ±1.4 cal/mol. In contrast, a single piece of quartz requires ΔH α-β be 107.7±1.4 cal/mol and has a T α-β hysteresis of 1.1 ° K. Regression of published data provides equations for the variation of the molar volume (cc/mol) of quartz with v. These equations imply a ΔV α-β of 0.205±0.031 cc/- mol. Expressions are also provided for the temperature dependence of the thermal coefficient of expansion, α, the compressibility, β, and (?/gb/?T)p (which is identically -(?α/?P) T ). DSC heat capacity measurements over the range 400 to 900 ° K were fitted to extended Maier-Kelley type expressions to give: $$\begin{gathered} C_P = 10.31 + 9.116 \times 10^{ - 3} T - \frac{{1.812 \times 10^5 }}{{T^2 }} \hfill \\ - {\text{5}}{\text{.630}} \times 10^{ - 2} {\text{ }}\frac{T}{{(T - 848)}} - 0.3553\frac{T}{{(T - 848)^2 }} \hfill \\ - 0.9011\frac{T}{{\left( {T - 848} \right)^3 }} \hfill \\ (400{\text{ to 842}}^ \circ {\text{K), and}} \hfill \\ C_P = - 318.8 + 0.2532T \hfill \\ {\text{ + }}\frac{{8.687 \times 10^7 }}{{T^2 }} + 0.1603\frac{T}{{\left( {T - 848} \right)^4 }} \hfill \\ \end{gathered} $$ (851 to 900 ° K), which together with the values of ΔH α?β measured over the range 842–851° K give 7875.3 cal/mol for H900-H400. The behavior of α, β, and C p as a function of T emphasizes that structural changes which occur at the α?β transition do so over a broad temperature interval.  相似文献    18. Thermodynamic properties of glaucophane new data from calorimetric and spectroscopic measurements      Ph. Gilletillet  B. Reynard  C. Tequi 《Physics and Chemistry of Minerals》1989,16(7):659-667 New data concerning glaucophane are presented. New high temperature drop calorimetry data from 400 to 800 K are used to constrain the heat capacity at high temperature. Unpublished low temperature calorimetric data are used to estimate entropy up to 900 K. These data, corrected for composition, are fitted for C p and S to the polynomial expressions (J · mol?1 · K?2) for T> 298.15 K: $$\begin{gathered} C_p = 11.4209 * 10^2 - 40.3212 * 10^2 /T^{{1 \mathord{\left/ {\vphantom {1 2}} \right. \kern-\nulldelimiterspace} 2}} - 41.00068 * 10^6 /T^2 \hfill \\ + 52.1113 * 10^8 /T^3 \hfill \\ \end{gathered} $$ $$\begin{gathered} S = 539 + 11.4209 * 10^2 * \left( {\ln T - \ln 298.15} \right) - 80.6424 * 10^2 \hfill \\ * \left( {T^{ - {1 \mathord{\left/ {\vphantom {1 2}} \right. \kern-\nulldelimiterspace} 2}} - 1/\left( {298.15} \right)^{{1 \mathord{\left/ {\vphantom {1 2}} \right. \kern-\nulldelimiterspace} 2}} } \right) + 20.50034 * 10^6 \hfill \\ * \left( {T^{ - 2} - 1/\left( {298.15} \right)^2 } \right) - 17.3704 * 10^8 * \left( {T^{ - 3} - \left( {1/298.15} \right)^3 } \right) \hfill \\ \end{gathered} $$ IR and Raman spectra from 50 to 3600 cm?1 obtained on glaucophane crystals close to the end member composition are also presented. These spectroscopic data are used with other data (thermal expansion, acoustic velocities etc.) in vibrational modelling. This last method provides an independent way for the determination of the thermodynamic properties (Cp and entropy). The agreement between measured and calculated properties is excellent (less than 2% difference between 100 and 1000 K). It is therefore expected that vibrational modelling could be applied to other amphiboles for which spectroscopic data are available. Finally, the enthalpy of formation of glaucophane is calculated.  相似文献    19. Assemblages among tephroite,pyroxmangite, rhodochrosite,quartz: Experimental data and occurrences in the Rhetic Alps      Tjerk Peters  Hans Schwander  Volkmar Trommsdorff 《Contributions to Mineralogy and Petrology》1973,42(4):325-332 Reactions involving the phases quartz-rhodochrosite-tephroite-pyroxmangite-fluid have been studied experimentally in the system MnO-SiO2-CO2-H2O at a pressure of 2 000 bars and resulted in the following expressions 1 $$\begin{gathered} {\text{Rhodochrosite + Quartz = Pyroxmangite + CO}}_2 \hfill \\ {\text{ log}}_{{\text{10}}} K^{{\text{2000 bars}}} = - \frac{{11.765}}{T} + 18.618. \hfill \\ {\text{Rhodochrosite + Pyroxmangite = Tephroite + CO}}_2 \hfill \\ {\text{ log}}_{{\text{10}}} K^{{\text{2000 bars}}} = - \frac{{7.083}}{T} + 11.870. \hfill \\ \end{gathered}$$ which can be used to derive data for the remaining two reactions among the phases under consideration. Field data from the Alps are in agreement with the metamorphic sequence resulting from the experiments.  相似文献    20. Stochastic analysis of bed-thickness distribution of sediments      S. Mizutani  I. Hattori 《Mathematical Geosciences》1972,4(2):123-146 On formation of a bed and distribution of bed thickness, A. N. Kolmogorov presented a mathematical explanation that if repetitive alternations of material accumulation and erosion form a sequence of beds, the resultant bed-thickness distribution curve takes a shape truncated by the ordinate at zero thickness. In this truncated distribution curve, its continuation and extension from positive to negative thickness represents the distribution of beds with negative thickness, that is, the depth of erosion. When a distribution curve, including both positive and negative parts, is expressed by a function f(x),the ratio \(\int_0^\infty {f(x)dx to} \int_{ - \infty }^\infty {f(x)dx} \) ,called Kolmogorov's coefficient and designated as p,is a parameter representing the degree of accumulation in the depositional environment. On the assumption that f(x)is described by the Gaussian distribution function, the coefficient pfor Permian and Pliocene sequences in central Japan was calculated. The coefficients also were obtained from published data for different types of sediments from other areas. It was determined that they are more or less different depending on their depositional environments. The calculated results are summarized as follows: $$\begin{gathered} p = 0.80 - 1.0for{\text{ }}alluvial{\text{ }}or{\text{ }}fluvial{\text{ }}deposits \hfill \\ p = 0.65 - 0.95for{\text{ }}nearshore{\text{ }}sediments \hfill \\ p = 0.55 - 0.95for{\text{ }}geosynclinal{\text{ }}sediments \hfill \\ p = 0.90 - 1.0for{\text{ }}varves \hfill \\ \end{gathered} $$ In addition, a ratio \(q = \int_0^\infty {xf(x)dx/} \int_{ - \infty }^\infty {|x|f(x)dx} \) ,called Kolmogorov's ratio in this paper, is introduced for estimating a degree of total thickness actually observed in the field relative to total thickness once present in a basin. The calculated results of Kolmogorov's ratio are as follows: $$\begin{gathered} q = 0.88 - 1.0for{\text{ }}alluvial{\text{ }}or{\text{ }}fluvial{\text{ }}deposits \hfill \\ q = 0.68 - 0.98for{\text{ }}nearshore{\text{ }}sediments \hfill \\ q = 0.55 - 0.96for{\text{ }}geosynclinal{\text{ }}sediments \hfill \\ q = 0.92 - 1.0for{\text{ }}varves \hfill \\ \end{gathered} $$ The sedimentological significance of these values is discussed.  相似文献