首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 93 毫秒
1.
This study examined the effects of different soil texture configurations on water movement and solute transport to provide a reliable scientific basis for the application of negative‐pressure irrigation (NPI) technology. HYDRUS‐2D was used to analyse water movement and solute transport under NPI. The main results are as follows: (a) HYDRUS‐2D can be used to simulate water movement and solute transport under NPI, as there was good agreement between the simulated and measured values for water contents, NaCl concentrations, cumulative water infiltration, and wetting distances in the horizontal and vertical directions; the Nash–Sutcliffe efficiency coefficients were in the range of 0.94–0.97. (b) Layered soils have obvious effects on water movement under NPI. With the emitter position in the loam layer, when a coarse texture of loamy sand was present below the loam layer (namely, L‐LS), irrigation water accumulated in the topsoil, and this led to an increase in evaporation compared with the homogeneous loam profile. However, fine texture silty loam or silty clay loam layers beneath the loam layer (namely, L‐SiL or L‐SiCL, respectively) was more conducive to water infiltration into the lower layer, and this increased the amount of water infiltration and simultaneously reduced the surface evaporation effectively. (c) Layered soils have obvious effects on solute transport under NPI, and salt accumulation will readily occur in the clay‐rich soil layer at the interface. The maximum soil salt accumulation of L‐LS occurred above the soil interface between the two soil layers with a value of 21.80 g/kg; however, for L‐SiCL and L‐SiL, the maximum salt accumulation occurred below the soil interface between the two soil layers, with values of 23.80 g/kg and 20.08 g/kg, respectively. (d) Interlayered soils showed remarkable changes in the water infiltration characteristics and salt‐leaching intensities under NPI, and the properties for the soil profile with a silty loam interlayer were better than those for the soil profile with a silty clay loam interlayer. The soil profile with a loamy sand interlayer had the lowest amount of water infiltration, which resulted in reductions of the salt‐leaching intensities. Thus, NPI is clearly not suitable for loamy sand soil. Overall, the results demonstrated that soil texture configurations affected water movement and solute transport under NPI. Therefore, careful consideration should be given to the use of NPI to achieve target soil water and solution conditions and reduce water loss.  相似文献   

2.
Testing infiltrometer techniques to determine soil hydraulic properties is necessary for specific soils. For a loam soil, the water retention and hydraulic conductivity predicted by the BEST (Beerkan Estimation of Soil Transfer parameters) procedure of soil hydraulic characterization was compared with data collected by more standard laboratory and field techniques. Six infiltrometer techniques were also compared in terms of saturated soil hydraulic conductivity, Ks. BEST yielded water retention values statistically similar to those obtained in the laboratory and Ks values practically coinciding with those determined in the field with the pressure infiltrometer (PI). The unsaturated soil hydraulic conductivity measured with the tension infiltrometer (TI) was reproduced satisfactorily by BEST only close to saturation. BEST, the PI, one‐potential experiments with both the TI and the mini disk infiltrometer (MDI), the simplified falling head (SFH) technique and the bottomless bucket (BB) method yielded statistically similar estimates of Ks, differing at the most by a factor of three. Smaller values were obtained with longer and more soil‐disturbing infiltration runs. Any of the tested infiltration techniques appears usable to obtain the order of magnitude of Ks at the field site, but the BEST, BB and PI data appear more appropriate to characterize the soil at some stage during a rainfall event. Additional investigations on both similar and different soils would allow development of more general procedures to apply infiltrometer techniques for soil hydraulic characterization. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

3.
Abstract

Knowledge of the variability of soil water content (SWC) in space and time plays a key role in hydrological and climatic modelling. However, limited attention has been given to arid regions. The focus of this study was to investigate the spatio-temporal variability of surface soil (0–6 cm) water content and to identify its controlling factors in a region of the Gobi Desert (40 km2). The standard deviation of SWC decreased logarithmically as mean water content decreased, and the coefficient of variation of SWC exhibited a convex upward pattern. The spatial variability of SWC also increased with the size of the investigated area. The spatial dependence of SWC changed over time, with stronger patterns of spatial organization in drier and wetter conditions of soil wetness and stochastic patterns in moderate soil water conditions. The dominant factors regulating the variability of SWC changed from combinations of soil and topographical properties (bulk density, clay content and relative elevation) in wet conditions to combinations of soil and vegetation properties (bulk density, clay content and shrub coverage) in dry conditions. This study has important implications for the assessment of soil quality and the sustainability of land management in arid regions.  相似文献   

4.
Lirong Lin  Jiazhou Chen 《水文研究》2015,29(9):2079-2088
Rain‐induced erosion and short‐term drought are the two factors that limit the productivity of croplands in the red soil region of subtropical China. The objective of this study was to estimate the effects of conservation practices on hydraulic properties and root‐zone water dynamics of the soil. A 3‐year experiment was performed on a slope at Xianning. Four treatments were evaluated for their ability to reduce soil erosion and improve soil water conditions. Compared with no practices (CK) and living grass strips (GS), the application of polyacrylamide (PAM) significantly reduced soil crust formation during intense rainfall, whereas rice straw mulching (SM) completely abolished soil crust formation. The SM and PAM treatments improved soil water‐stable aggregates, with a redistribution of micro‐aggregates into macro‐aggregates. PAM and SM significantly increased the soil water‐holding capacity. These practices mitigated the degradation of the soil saturated hydraulic conductivity (Ks) during intense rainfalls. These methods increased soil water storage but with limited effects during heavy rainfalls in the wet period. In contrast, during the dry period, SM had the highest soil water storage, followed by PAM and CK. Grass strips had the lowest soil water storage because of the water uptake during the vigorous grass growth. A slight decline in the soil moisture resulted in a significant decrease in the unsaturated hydraulic conductivity (Ku) of the topsoil. Therefore, the hydraulic conductivity in the field is governed by soil moisture, and the remaining soil moisture is more important than improving soil properties to resist short‐term droughts. As a result, SM is the most effective management practice when compared with PAM and GS, although they all protect the soil hydraulic properties during wet periods. These results suggest that mulching is the best strategy for water management in erosion‐threatened and drought‐threatened red soils. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

5.
Soil water content (SWC) is an important factor in transfer processes between soil and air, contributing to water and energy balances, and quantifying it remains a challenge. This study uses artificial neural networks (ANNs) to analyse spatial and temporal variation of SWC in a Brazilian watershed, based on climate information, soil physical properties and topographic variables. Thirty eight input variables were tested in 200 models. The outputs were compared with 650 gravimetric moisture measurements collected at 26 points (25 field studies). The results show that it is possible to estimate SWC efficiently (Nash-Sutcliffe statistic, NS = 0.77) using topographic data, soil physical properties and rainfall. If only climate information is considered, modelling is less efficient (NS = 0.28). Using many variables does not necessarily improve performance. Alternatively, SWC can be estimated by simplified models using rainfall and topographic maps information, although the performance is less good (NS = 0.65).  相似文献   

6.
On patterned peatlands, open water pools develop within a matrix of terrestrial vegetation (‘ridges’). Regional patterns in the distribution of ridge–pool complexes suggest that the relative cover of these two surface types is controlled in part by climate wetness, but landscape topography must also be an important controlling factor. In this paper, a functional model that relates relative cover of ridges and pools to climate and surface gradient was developed and tested. The model was formulated in terms of a water budget, based on the differential effects of ridges and pools on losses by evapotranspiration and subsurface flow. It predicts a positive relationship between surface gradient and ridge proportion, with a linear effect related to water supply and ridge hydraulic conductivity, modified at high ridge proportion by differences in evapotranspiration between ridges and pools. The limit to patterned peatland distribution occurs where the surface is completely covered by ridges. The model may be sensitive or insensitive to climate differences between localities, depending on whether hydraulic characteristics of ridge peat co‐vary with water supply. To distinguish between these alternative hypotheses, surface gradient and ridge proportion were surveyed along 20 transects in each of three localities in Scotland that differ threefold in net precipitation to pools. The results of the field survey served to reject the climate‐sensitive hypothesis, but were consistent with the climate‐insensitive hypothesis. Analysis of the residuals suggested that variation within localities was related more to topographic control of water supply than to ridge hydraulic conductivity or developmental stage. Hence, within this maritime climate region, the distribution of ridge–pool complexes and the relative abundance of pools are controlled mainly by topographic variables. Field surveys across both maritime and continental regions are required to confirm a subtle climatic effect that allows pools to occur on higher gradients in drier climates than in wetter climates. Further development and testing of the functional model will provide a stronger basis for assessing potential feedback between climate change, peatland surface structure and methane emission from pools. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

7.
Influences of vegetation on shallow (< 1 m) soil slip formation through modification of soil water was investigated on hillsides covered by verdant chaparral (dense shrubland), and burned vegetation in the Transverse Ranges of California. Per cent available water and hydraulic potentials were obtained from electrical resistance blocks and tensiometers for one year in soils under burned and unburned vegetation on three slopes. Soil remained moister during a dry period under burned vegetation than under unburned chaparral on two of the three slopes studied. Daily increases in per cent available water and hydraulic potential of soils were greatest for a given storm where soil was driest prior to the storm. Furthermore, water levels in soil tended to be greatest for a given storm where soil water levels had been lowest prior to the storm. These two findings were corroborated by laboratory wetting trials on undisturbed soils of vastly differing mechanical properties in that initially drier soils always absorbed water faster and became wetter than initially moister soils. In the field, soil water levels became similarly high under all vegetation after several storms and varied little throughout the remainder of the wet season. These results contradict the common assumption that depletion of soil water by vegetation would result in slower saturation rates and hence greater resistance of a soil mass to slippage.  相似文献   

8.
The occurrence of water ponding on soil surfaces during and after heavy rainfall produces surface run‐off or surface water accumulation in low‐lying areas, which might reduce the water supply to soils and result in a reduction of the soil water that plants can use, especially in arid climates. On Mongolian rangeland, we observed ponded water on the surface of a specific soil condition subjected to a heavy rainfall of 30 mm/hr. By contrast, ponded water was not observed for the same type of soil where livestock grazing had been removed for 6–8 years via a fence or for nearby soil containing less clay. We measured the infiltration rate (the saturated hydraulic conductivity of the surface soil, Ks) of the three sites by applying ponded water on the soil surface (an intake rate test). The results showed that Ks in the rangeland was lower than the rainfall intensity in the site where water ponded on the soil surface; however, Ks of the soil inside of the fence has recovered to 3 times that of the soil outside of the fence to exceed the rainfall intensity. Heavy rainfall that exceeds the infiltration rate occurs several times a year at the livestock grazing site where we observed ponded water. Slight water repellency of the soil reduces rain infiltration to increase the possibility of surface ponding for the soil.  相似文献   

9.
Water repellency is a widespread property of Pinus pinaster and Eucalyptus globulus forest soils in NW Spain and is particularly severe during the summer dry conditions. The aim of this work was to compare actual water repellency at field‐moist samples with potential water repellency after drying at 25 and 105 °C in samples collected at different times of year under four forest soils. Also, we investigated whether drying at 25 or 105 °C led to repellency values comparable to the highest levels reached under field conditions in the summer with a view to developing an appropriate sampling protocol towards estimating the maximum possible water repellency of a given soil as a key to establishing its environmental effects. The actual and potential water repellency was determined by using the water drop penetration time (WDPT) and molarity of an ethanol drop (MED) tests. Clear seasonal patterns of water repellency were observed from the results for the four forest soils, peaking in the dry period and disappearing after prolonged wet periods. Water repellency lasts longer in sandy loam soils than in more finely textured soils, and also under eucalyptus than under pine forests. Drying soil samples at 25 or 105 °C increased water repellency, as measured with the WDPT method, in the four soils, but especially in the non‐repellent samples collected during the wet period. The increase was more marked in the sandy loam soils than in the more finely textured soils, and also after drying at 105 °C than at 25 °C. MED measurements exposed a common trait in the four soils; thus, the water repellency values obtained under field conditions in summer invariably exceeded those obtained after drying at 25 or 105 °C. In addition, the repellency values for dried samples collected in the wet period were never comparable to the maximum levels observed under field conditions in the summer. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

10.
The hydraulic properties of the topsoil control the partition of rainfall into infiltration and runoff at the soil surface. They must be characterized for distributed hydrological modelling. This study presents the results of a field campaign documenting topsoil hydraulic properties in a small French suburban catchment (7 km2) located near Lyon, France. Two types of infiltration tests were performed: single ring infiltration tests under positive head and tension‐disk infiltration using a mini‐disk. Both categories were processed using the BEST—Beerkan Estimation of Soil Transfer parameters—method to derive parameters describing the retention and hydraulic conductivity curves. Dry bulk density and particle size data were also sampled. Almost all the topsoils were found to belong to the sandy loam soil class. No significant differences in hydraulic properties were found in terms of pedologic units, but the results showed a high impact of land use on these properties. The lowest dry bulk density values were obtained in forested soils with the highest organic matter content. Permanent pasture soils showed intermediate values, whereas the highest values were encountered in cultivated lands. For saturated hydraulic conductivity, the highest values were found in broad‐leaved forests and small woods. The complementary use of tension‐disk and positive head infiltration tests highlighted a sharp increase of hydraulic conductivity between near saturation and saturated conditions, attributed to macroporosity effect. The ratio of median saturated hydraulic conductivity to median hydraulic conductivity at a pressure of − 20 mm of water was about 50. The study suggests that soil texture, such as used in most pedo‐transfer functions, might not be sufficient to properly map the variability of soil hydraulic properties. Land use information should be considered in the parameterizations of topsoil within hydrological models to better represent in situ conditions, as illustrated in the paper. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

11.
Spatio‐temporal heterogeneity in soil water content is recognized as a common phenomenon, but heterogeneity in the hydrogen and oxygen isotope composition of soil water, which can reveal processes of water cycling within soils, has not been well studied. New advances are being driven by measurement approaches allowing sampling with high density in both space and time. Using in situ soil water vapour probe techniques, combined with conventional soil and plant water vacuum distillation extraction, we monitored the hydrogen and oxygen stable isotopic composition of soil and plant waters at paired sites dominated by grasses and Gambel's oak (Quercus gambelii) within a semiarid montane ecosystem over the course of a growing season. We found that sites spaced only 20 m apart had profoundly different soil water isotopic and volumetric conditions. We document patterns of depth‐ and time‐explicit variation in soil water isotopic conditions at these sites and consider mechanisms for the observed heterogeneity. We found that soil water content and isotopic variability were damped under Q. gambelii, perhaps due in part to hydraulic redistribution of deep soil water or groundwater by Q. gambelii in these soils relative to the grass‐dominated site. We also found some support for H isotope discrimination effects during water uptake by Q. gambelii. In this ecosystem, the soil water content was higher than that at the neighbouring Grass site, and thus, 25% more water was available for transpiration by Q. gambelii compared with the Grass site. This work highlights the role of plants in governing soil water variation and demonstrates that they can also strongly influence the isotope ratios of soil water. The resulting fine‐scale heterogeneity has implications for the use of isotope tracers to study soil hydrology and evaporation and transpiration fluxes to improve understanding of water cycling through the soil–plant–atmosphere continuum.  相似文献   

12.
The interaction effects of different applied ratios of a hydrophilic polymer (Superab A200) (0, 0.2, 0.6% w/w) under various soil salinity levels (initial salinity, 4 and 8 ms/cm) were evaluated on available water content (AWC), biomass, and water use efficiency for corn grown in loamy sand and sandy clay loam soils. The results showed that the highest AWC was measured at the lowest soil salinity. The application of 0.6% w/w of the polymer at the lowest salinity level increased the AWC by 2.2 and 1.2 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. The analysis of variance of data showed that the effect of salinity was significant on biomass and water use efficiency of corn in the loamy sand and sandy clay loam soils. The highest amounts of these traits were measured in soils with the lowest salinity level. Application of polymer at the rate of 0.6% in the loamy sand soil and at the rate of 0.2% in the sandy clay loam soil resulted in the highest aerial and root biomass and water use efficiency for corn. At these polymer rates the amounts of water use efficiency for corn were 2.6 and 1.7 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. Thus, the use of hydrophilic polymer in soils especially in the sandy soils increases soil water holding capacity, yield, and water use efficiency of plant. On the other hand, decreases the negative effect of soil salinity on plant and helps for irrigation projects to succeed in arid and semi‐arid areas.  相似文献   

13.
The study investigated the processes involved in metolachlor transport in two artificially drained, structured soils in eastern France. Measured losses of bromide and metolachlor in drainage water were compared with results simulated by the mechanistic, stochastic AgriFlux model. Simulated drainage water volumes were generally similar to the measured volumes when the spatial variability of the soil water properties was taken into account. When such variability was disregarded, cumulative water volumes of the clay soil were over- or underestimated by more than 20%. Two types of adsorption were tested. For instantaneous, reversible adsorption, using the partition coefficient Koc, metolachlor losses were underestimated in the first drainage water volumes and overestimated for the total study period. The use of slow adsorption and desorption kinetics (ADK) produced an export pattern similar to the observed one. A sensitivity analysis indicated that the simulated results are very sensitive to the values of the ADK rates, especially for the silty loam soil. The effect of ADK on the attenuation of metolachlor exports was more significant than the effect of degradation (2.3 and 6.7 times higher for the clay and silty loam soils, respectively). For the same four-month period, the bromide and metolachlor losses (using ADK) in the clay soil were 2.1 and 1.3 times greater, respectively, if the macroporosity was set at 10% than if it was not simulated. Conversely, macroporosity did not significantly affect these losses in the silty loam. The main factors involved in the metolachlor transport in the studied soils were: (i) the macroporosity, especially in the clay soil because of the low hydraulic conductivity of the matrix and (ii) the sorption kinetics rates which varied according to the soil physico-chemical characteristics.  相似文献   

14.
The effects of soil water content (SWC) on the formation of run‐off in grass swales draining into a storm sewer system were studied in two 30‐m test swales with trapezoidal cross sections. Swale 1 was built in a loamy fine‐sand soil, on a slope of 1.5%, and Swale 2 was built in a sandy loam soil, on a slope of 0.7%. In experimental runs, the swales were irrigated with 2 flow rates reproducing run‐off from block rainfalls with intensities approximately corresponding to 2‐month and 3‐year events. Run‐off experiments were conducted for initial SWC (SWCini) ranging from 0.18 to 0.43 m3/m3. For low SWCini, the run‐off volume was greatly reduced by up to 82%, but at high SWCini, the volume reduction was as low as 15%. The relative swale flow volume reductions decreased with increasing SWCini and, for the conditions studied, indicated a transition of the dominating swale functions from run‐off dissipation to conveyance. Run‐off flow peaks were reduced proportionally to the flow volume reductions, in the range from 4% to 55%. The swale outflow hydrograph lag times varied from 5 to 15 min, with the high values corresponding to low SWCini. Analysis of swale inflow/outflow hydrographs for high SWCini allowed estimations of the saturated hydraulic conductivities as 3.27 and 4.84 cm/hr in Swales 1 and 2, respectively. Such estimates differed from averages (N = 9) of double‐ring infiltrometer measurements (9.41 and 1.78 cm/hr). Irregularities in swale bottom slopes created bottom surface depression storage of 0.35 and 0.61 m3 for Swales 1 and 2, respectively, and functioned similarly as check berms contributing to run‐off attenuation. The experimental findings offer implications for drainage swale planning and design: (a) SWCini strongly affect swale functioning in run‐off dissipation and conveyance during the early phase of run‐off, which is particularly important for design storms and their antecedent moisture conditions, and (b) concerning the longevity of swale operation, Swale 1 remains fully functional even after almost 60 years of operation, as judged from its attractive appearance, good infiltration rates (3.27 cm/hr), and high flow capacity.  相似文献   

15.
This paper discusses the effects of water quality on the hydrological and erosion response of non‐saline, non‐sodic soils during simulated rain experiments. It is well known that rain water quality affects the behaviour of saline soils. In particular, rain simulation experiments cannot be run using tap water if realistic values of infiltration rates and soil erosion are to be found. This paper reports on similar effects for non‐saline, non‐sodic soils. Two soils – a well‐aggregated clay‐rich soil developed on marine silty clay deposits and a soil developed on silt loam – were selected and subjected to a series of simulated rainstorms using demineralized water and tap water. The experiments were conducted in two different laboratories in order to obtain results independent of the tap water quality or the rainfall simulator characteristics. The results indicate that time‐to‐ponding is largely delayed by solute‐rich water (tap water). When tap water is used, infiltration rates are significantly overestimated, i.e. by more than 100 per cent. Interrill erosion rates increase by a factor of 2·5–3 when demineralized water is used. The silty clay soil was more affected by the water quality than the silt loam soil, with respect to infiltration and runoff production. Regarding interrill erosion rates, the two tested soils were similarly affected by the water quality. Therefore, it can be concluded that rainfall simulation experiments with non‐dispersive soils (e.g. non‐saline, non‐sodic) must also be conducted using water with very low electrical conductivity (i.e. less than 30–50 µS cm−1), close to that of distilled water. The use of tap water certainly hampers comparisons and the relative ranking of the hydrological and erosion response of different soils, while parameter values, such as final infiltration rate or time‐to‐ponding, cannot be extrapolated and extended to natural situations. Therefore, the majority of hydrological and erosion models and parameter values measured during rainfall simulations in the past should be used with caution for all types of soils. Copyright © 2001 John Wiley & Sons, Ltd.  相似文献   

16.
To evaluate the relationship between the moisture conditions and the water repellency of soil surfaces in situ, we periodically conducted field surveys for more than a year in a humid‐temperate forest in Japan. Measurements were made in four plots with varying soil physicochemical properties and under different topographic conditions across a hillslope. Each plot contained permanent quadrats with measurement points in a grid pattern. At each point, we measured the volumetric water content at 0‐ to 5‐cm depths and the water repellency at soil surfaces approximately twice a month. The repeated measurements enabled us to estimate the critical water content (CWC) below which soils repelled water at each point. We defined the representative CWC (RCWC) of a plot as the median of all CWCs in a plot and estimated the representative critical water potential (RCWP) on the basis of the RCWC using the water retention curve. The RCWC values differed among plots, but the corresponding RCWP values were similar (pF = 3.5–3.9). The relationship of the areal fraction showing water repellency against soil water potentials was similar across plots, but the relationship differed among plots against the soil moisture content. These results suggest that soil water potential is more indicative of the spatial occurrence of water repellency than moisture content on a hillslope where soil physicochemical properties vary. Plots located on ridge crests frequently exhibited lower water potentials and showed a higher areal fraction of water repellency, implying a greater chance of generating surface runoff by rainfall events. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

17.
Jos C. van Dam 《水文研究》2000,14(6):1101-1117
Single domain models may seriously underestimate leaching of nutrients and pesticides to groundwater in clay soils with shrinkage cracks. Various two‐domain models have been developed, either empirical or physically based, which take into account the effects of cracks on water flow and solute transport. This paper presents a model concept that uses the clay shrinkage characteristics to derive crack volume and crack depth under transient field conditions. The concept has been developed to simulate field average behaviour of a field with cracks, rather than flow and transport at a small plot. Water flow and solute transport are described with basic physics, which allow process and scenario analysis. The model concept is part of the more general agrohydrological model SWAP, and is applied to a field experiment on a cracked clay soil, at which water flow and bromide transport were measured during 572 days. A single domain model was not able to mimic the field‐average water flow and solute transport. Incorporation of the crack concept considerably improved the simulation of water content and bromide leaching to the groundwater. Still deviations existed between the measured and simulated bromide concentration profiles. The model did not reproduce the observed bromide retardation in the top layer and the high bromide dispersion resulting from water infiltration at various soil depths. A sensitivity analysis showed that the amounts of bromide leached were especially sensitive to the saturated hydraulic conductivity of the top layer, the solute transfer from the soil matrix to crack water flow and the mean residence time of rapid drainage. The shrinkage characteristic and the soil hydraulic properties of the clay matrix showed a low sensitivity. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

18.
Using a Simple Soil Column Method to Evaluate Soil Phosphorus Leaching Risk   总被引:3,自引:0,他引:3  
The impacts of soil P leaching on water eutrophication have widely been concerned. However, there is no dependable method to quantitatively estimate the P leaching risk of soils. In this study, a simple soil column method was developed using two calcareous Fluvisols, silt loam and loam. The soil column was 20 cm in length and 5 cm in diameter, and distilled water was continuously supplied from the top. The volume and dissolved reactive P (DRP) concentrations of leachate were measured. Results showed that DRP concentrations in leachate increased slowly for the low soil Olsen‐P levels but rapidly for the high Olsen‐P levels. According to these two‐phase changes in the DRP versus soil Olsen‐P contents, the thresholds of P leaching risk were estimated to be 41.1 and 62.3 mg P kg?1 (Olsen‐P) for silt loam and loam, respectively. The P leaching intensity of soils increased by 3‐ to 540‐fold if the soil Olsen‐P contents accumulated from 6.6 to 155.5 mg P kg?1. The outcomes derived from this study regarding the determination of P leaching threshold and intensity by the soil column method also need a further verification on more soils with a wide range of physical and chemical properties.  相似文献   

19.
The determination of clay content in near‐surface formations is crucial for geotechnical, hydrogeological and oil‐contamination studies. We have developed a technique for estimating clay content that consists of the minimization of the difference between the theoretically calculated and measured soil resistivities as a function of water salinity. To calculate the resistivity, we used a model that takes into account the electrochemical processes in the clay micropores. The experimental measurements of soil resistivity were performed on soil samples, completely saturated by brines at different concentrations of NaCl salt in the range 0.6–100 g/l, to obtain the resistivity versus salinity curve. The parameters obtained with this curve inversion are the clay content, the total porosity and the cation exchange capacity. To verify the new technique, we determined clay concentrations of artificial mixtures of calibrated sand and clay. The relative mean error in the clay content does not exceed 20% for a 5% fitting error of the resistivity versus salinity curves. Such evaluations allow the correct separation of the main lithological groups (sand, sandy loam, loam, and light, medium and heavy clay). We applied this technique to estimate the petrophysical parameters of soils (clay content, porosity and cation exchange capacity) at various sites in Mexico. The results improved the interpretation of the vertical electrical soundings, the lithological soil characterization and the delineation of oil‐contaminated areas.  相似文献   

20.
Research shows that water repellency is a key hydraulic property that results in reduced infiltration rates in burned soils. However, more work is required in order to link the hydrological behaviour of water repellent soils to observed runoff responses at the plot and hillslope scale. This study used 5 M ethanol and water in disc infiltrometers to quantify the role of macropore flow and water repellency on spatial and temporal infiltration patterns in a burned soil at plot (<10 m2) scale in a wet eucalypt forest in south‐east Australia. In the first summer and winter after wildfire, an average of 70% and 60%, respectively, of the plot area was water repellent and did not contribute to infiltration. Macropores (r > 0·5 mm), comprising just 5·5% of the soil volume, contributed to 70% and 95%, respectively, of the field‐saturated and ponded hydraulic conductivity (Kp). Because flow occurred almost entirely via macropores in non‐repellent areas, this meant that less than 2·5% of the soil surface effectively contributed to infiltration. The hydraulic conductivity increased by a factor of up to 2·5 as the hydraulic head increased from 0 to 5 mm. Due to the synergistic effect of macropore flow and water repellency, the coefficient of variation (CV) in Kp was three times higher in the water‐repellent soil (CV = 175%) than under the simulated non‐repellent conditions (CV = 66%). The high spatial variability in Kp would act to reduce the effective infiltration rate during runoff generation at plot scale. Ponding, which tend to increase with increasing scale, activates flow through macropores and would raise the effective infiltration rates at larger scales. Field experiments designed to provide representative measurements of infiltration after fire in these systems must therefore consider both the inherent variability in hydraulic conductivity and the variability in infiltration caused by interactions between surface runoff and hydraulic conductivity. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号