首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 531 毫秒
1.
Developing models to predict on‐site soil erosion and off‐site sediment transport at the agricultural watershed scale represent an on‐going challenge in research today. This study attempts to simulate the daily discharge and sediment loss using a distributed model that combines surface and sub‐surface runoffs in a small hilly watershed (< 1 km2). The semi‐quantitative model, Predict and Localize Erosion and Runoff (PLER), integrates the Manning–Strickler equation to simulate runoff and the Griffith University Erosion System Template equation to simulate soil detachment, sediment storage and soil loss based on a map resolution of 30 m × 30 m and over a daily time interval. By using a basic input data set and only two calibration coefficients based, respectively, on water velocity and soil detachment, the PLER model is easily applicable to different agricultural scenarios. The results indicate appropriate model performance and a high correlation between measured and predicted data with both Nash–Sutcliffe efficiency (Ef) and correlation coefficient (r2) having values > 0.9. With the simple input data needs, PLER model is a useful tool for daily runoff and soil erosion modeling in small hilly watersheds in humid tropical areas. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

2.
Effective control of nonpoint source pollution from contaminants transported by runoff requires information about the source areas of surface runoff. Variable source hydrology is widely recognized by hydrologists, yet few methods exist for identifying the saturated areas that generate most runoff in humid regions. The Soil Moisture Routing model is a daily water balance model that simulates the hydrology for watersheds with shallow sloping soils. The model combines elevation, soil, and land use data within the geographic information system GRASS, and predicts the spatial distribution of soil moisture, evapotranspiration, saturation‐excess overland flow (i.e., surface runoff), and interflow throughout a watershed. The model was applied to a 170 hectare watershed in the Catskills region of New York State and observed stream flow hydrographs and soil moisture measurements were compared to model predictions. Stream flow prediction during non‐winter periods generally agreed with measured flow resulting in an average r2 of 0·73, a standard error of 0·01 m3/s, and an average Nash‐Sutcliffe efficiency R2 of 0·62. Soil moisture predictions showed trends similar to observations with errors on the order of the standard error of measurements. The model results were most accurate for non‐winter conditions. The model is currently used for making management decisions for reducing non‐point source pollution from manure spread fields in the Catskill watersheds which supply New York City's drinking water. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

3.
Increasing population and intensification of agriculture increase erosion rates and often result in severe land degradation and sedimentation of reservoirs. Finding effective management practices to counteract the increasing sediment load is becoming increasingly urgent especially in the Ethiopian highlands where the construction of the hydroelectric Grand Renaissance Dam on the Blue Nile is underway. In this paper, we examine the results of 9 years of a watershed experiment in which discharge and sediment losses were observed in the 113 ha Anjeni watershed of the Blue Nile Basin. The study period encompasses conditions before, during, and after the installation of graded Fanya‐Juu (“throw uphill” bunds) soil and water conservation practices (SWCP), which had the ultimate goal of creating terraces. We use a saturation‐excess runoff model named the parameter‐efficient distributed model as a mathematical construct to relate rainfall with discharge and sediment losses at the outlet. The parameter‐efficient distributed model is based on landscape units in which the excess rainfall becomes direct runoff or infiltrates based on topographic position or hardpan characteristics. Deviations in this rainfall–discharge–sediment loss relationship are ascribed to the changes in infiltration characteristics caused by SWCPs on the hillslopes. With this technique, we found that in the Anjeni basin, the Fanya‐Juu SWCPs are only effective in increasing the infiltration and thereby reducing the direct runoff and sediment concentrations in the first 5 years. At the end of the 9‐year observation period, the direct runoff and sediment concentrations were barely reduced compared to the levels before SWCP were installed. In addition, we found that the model structure based on landscape units was able to represent the varying runoff and erosion processes during the 9 years well by varying mainly the portion of degraded land (and thereby representing the effectiveness of the Fanya‐Juu to reduce runoff by increasing infiltration).  相似文献   

4.
In this paper, we analyse how the performance and calibration of a distributed event‐based soil erosion model at the hillslope scale is affected by different simplifications on the parameterizations used to compute the production of suspended sediment by rainfall and runoff. Six modelling scenarios of different complexity are used to evaluate the temporal variability of the sedimentograph at the outlet of a 60 m long cultivated hillslope. The six scenarios are calibrated within the generalized likelihood uncertainty estimation framework in order to account for parameter uncertainty, and their performance is evaluated against experimental data registered during five storm events. The Nash–Sutcliffe efficiency, percent bias and coverage performance ratios show that the sedimentary response of the hillslope in terms of mass flux of eroded soil can be efficiently captured by a model structure including only two soil erodibility parameters, which control the rainfall and runoff production of suspended sediment. Increasing the number of parameters makes the calibration process more complex without increasing in a noticeable manner the predictive capability of the model. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

5.
Climate change is expected to effect storm runoff and erosion processes in Mediterranean watersheds at multiple spatial scales. Models are typically applied to estimate these impacts; however, the scarcity of spatially distributed data for parameterization, calibration and validation often prevents application of these models, particularly for larger catchments. This report, the first part of a two‐part article, presents an application and evaluation of the MEFIDIS model for two Mediterranean meso‐scale watersheds (115 and 290 km2) in a data‐scarce environment. A multi‐scale assessment method was used that combines quantitative validation and qualitative evaluation, consisting of three steps: (1) calibration at the small (field) scale using results from rainfall simulation experiments; (2) calibration and validation for catchment‐scale results while changing catchment‐scale parameters only (channel roughness and a parameter controlling the distribution of saturated areas); and (3) qualitative evaluation of within‐watershed erosion processes using empirical estimates of sediment delivery ratio and gully location. The results indicate that calibrating MEFIDIS at the field scale can provide reasonable results for catchment runoff and sediment export and for within‐watershed erosion processes. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

6.
Long‐term erosion monitoring data in the Ethiopian highlands are only available from the Soil Conservation Research Program (SCRP) watersheds including the Anjeni watershed. The 113 ha Anjeni watershed was established in 1984 and fanya juu terraces were installed in 1986. Runoff and erosion data are available from three different plot sizes and at the watershed outlet. The objective of this study was to investigate how erosion processes and sediment rating parameters vary with plot size and the progression of the rainy monsoon phase. We analyzed runoff and sediment loss data from 40 plots and the watershed outlet. The dataset included erosion data from 24 newly constructed plots (3 m length) during the rainy monsoon phase of 2012 and 2013, and 16 long‐term plots (with 12, 16, 22, and 24% slopes and 3, 15 and 30 m lengths) and the watershed outlet during the period between 1986 to 1990. Sediment concentration (C) was fitted to runoff (Q) using a power regression equation (C = aQb). Sediment concentration and yield increased with increasing plot length from 3 m to 15 m, but sediment yield decreased as plot length increased to 30 m.The coefficients (a and b) were affected by plot size and the progression of the rainy monsoon phase. As plot size increases, the a value increased, while the b value decreased. Greater a values were observed during the beginning of the monsoon phase, while values of b were greater towards the end of the monsoon phase. Overall findings suggest that erosion from cultivated fields is primarily controlled by transport limitations at the beginning of the monsoon phase, while towards the end of the monsoon phase, as surface covers emerge, sediment availability will be reduced, and thus sediment source would be a limitation. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

7.
The impacts of climate change on storm runoff and erosion in Mediterranean watersheds are difficult to assess due to the expected increase in storm frequency coupled with a decrease in total rainfall and soil moisture, added to positive or negative changes to different types of vegetation cover. This report, the second part of a two‐part article, addresses this issue by analysing the sensitivity of runoff and erosion to incremental degrees of change (from ? 20 to + 20%) to storm rainfall, pre‐storm soil moisture, and vegetation cover, in two Mediterranean watersheds, using the MEFIDIS model. The main results point to the high sensitivity of storm runoff and peak runoff rates to changes in storm rainfall (2·2% per 1% change) and, to a lesser degree, to soil water content (?1·2% per 1% change). Catchment sediment yield shows a greater sensitivity than within‐watershed erosion rates to both parameters: 7·8 versus 4·0% per 1% change for storm rainfall, and ? 4·9 versus ? 2·3% per 1% change for soil water content, indicating an increase in sensitivity with spatial scale due to changes to sediment connectivity within the catchment. Runoff and erosion showed a relatively low sensitivity to changes in vegetation cover. Finally, the shallow soils in one of the catchments led to a greater sensitivity to changes in storm rainfall and soil moisture. Overall, the results indicate that decreasing soil moisture levels caused by climate change could be sufficient to offset the impact of greater storm intensity in Mediterranean watersheds. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

8.
A simple grid cell‐based distributed hydrologic model was developed to provide spatial information on hydrologic components for determining hydrologically based critical source areas. The model represents the critical process (soil moisture variation) to run‐off generation accounting for both local and global water balance. In this way, it simulates both infiltration excess run‐off and saturation excess run‐off. The model was tested by multisite and multivariable evaluation on the 50‐km2 Little River Experimental Watershed I in Georgia, U.S. and 2 smaller nested subwatersheds. Water balance, hydrograph, and soil moisture were simulated and compared to observed data. For streamflow calibration, the daily Nash‐Sutcliffe coefficient was 0.78 at the watershed outlet and 0.56 and 0.75 at the 2 nested subwatersheds. For the validation period, the Nash‐Sutcliffe coefficients were 0.79 at the watershed outlet and 0.85 and 0.83 at the 2 subwatersheds. The per cent bias was less than 15% for all sites. For soil moisture, the model also predicted the rising and declining trends at 4 of the 5 measurement sites. The spatial distribution of surface run‐off simulated by the model was mainly controlled by local characteristics (precipitation, soil properties, and land cover) on dry days and by global watershed characteristics (relative position within the watershed and hydrologic connectivity) on wet days when saturation excess run‐off was simulated. The spatial details of run‐off generation and travel time along flow paths provided by the model are helpful for watershed managers to further identify critical source areas of non‐point source pollution and develop best management practices.  相似文献   

9.
Phosphorus (P) loss from agricultural watersheds has long been a critical water quality problem, the control of which has been the focus of considerable research and investment. Preventing P loss depends on accurately representing the hydrological and chemical processes governing P mobilization and transport. The Soil and Water Assessment Tool (SWAT) is a watershed model commonly used to predict run‐off and non‐point source pollution transport. SWAT simulates run‐off employing either the curve number (CN) or the Green and Ampt methods, both assume infiltration‐excess run‐off, although shallow soils underlain by a restricting layer commonly generate saturation‐excess run‐off from variable source areas (VSA). In this study, we compared traditional SWAT with a re‐conceptualized version, SWAT‐VSA, that represents VSA hydrology, in a complex agricultural watershed in east central Pennsylvania. The objectives of this research were to provide further evidence of SWAT‐VSA's integrated and distributed predictive capabilities against measured surface run‐off and stream P loads and to highlight the model's ability to drive sub‐field management of P. Thus, we relied on a detailed field management database to parameterize the models. SWAT and SWAT‐VSA predicted discharge similarly well (daily Nash–Sutcliffe efficiencies of 0.61 and 0.66, respectively), but SWAT‐VSA outperformed SWAT in predicting P export from the watershed. SWAT estimated lower P loss (0.0–0.25 kg ha?1) from agricultural fields than SWAT‐VSA (0.0–1.0+ kg ha?1), which also identified critical source areas – those areas generating large run‐off and P losses at the sub‐field level. These results support the use of SWAT‐VSA in predicting watershed‐scale P losses and identifying critical source areas of P loss in landscapes with VSA hydrology. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

10.
Z. X. Xu  J. P. Pang  C. M. Liu  J. Y. Li 《水文研究》2009,23(25):3619-3630
The Soil and Water Assessment Tool (SWAT) was used to simulate the transport of runoff and sediment into the Miyun Reservoir, Beijing in this study. The main objective was to validate the performance of SWAT and the feasibility of using this model as a simulator of runoff and sediment transport processes at a catchment scale in arid and semi‐arid area in North China, and related processes affecting water quantity and soil erosion in the catchment were simulated. The investigation was conducted using a 6‐year historical streamflow and sediment record from 1986 to 1991; the data from 1986 to 1988 was used for calibration and that from 1989 to 1991 for validation. The SWAT generally performs well and could accurately simulate both daily and monthly runoff and sediment yield. The simulated daily and monthly runoff matched the observed values satisfactorily, with a Nash‐Sutcliffe coefficient of greater than 0·6, 0·9 and a coefficient of determination 0·75, 0·9 at two outlet stations (Xiahui and Zhangjiafen stations) during calibration. These values were 0·6, 0·85 and 0·6, 0·9 during validation. For sediment simulation, the efficiency is lower than that for runoff. Even so, the Nash‐Sutcliffe coefficient and coefficient of determination were greater than 0·48 and 0·6 for monthly sediment yield during calibration, and these values were greater than 0·84 and 0·95 during validation. Sensitivity analysis shows that sensitive parameters for the simulation of discharge and sediment yield include curve number, base flow alpha factor, soil evaporation compensation factor, soil available water capacity, soil profile depth, surface flow lag time and channel re‐entrained linear parameter, etc. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

11.
Agricultural pollutant runoff is a major source of water contamination in California's Sacramento River watershed where 8500 km2 of agricultural land influences water quality. The Soil and Water Assessment Tool (SWAT) hydrology, sediment, nitrate and pesticide transport components were assessed for the Sacramento River watershed. To represent flood conveyance in the area, the model was improved by implementing a flood routing algorithm. Sensitivity/uncertainty analyses and multi‐objective calibration were incorporated into the model application for predicting streamflow, sediment, nitrate and pesticides (chlorpyrifos and diazinon) at multiple watershed sites from 1992 to 2008. Most of the observed data were within the 95% uncertainty interval, indicating that the SWAT simulations were capturing the uncertainties that existed, such as model simplification, observed data errors and lack of agricultural management data. The monthly Nash–Sutcliffe coefficients at the watershed outlet ranged from 0.48 to 0.82, indicating that the model was able to successfully predict streamflow and agricultural pollutant transport after calibration. Predicted sediment loads were highly correlated to streamflow, whereas nitrate, chlorpyrifos and diazinon were moderately correlated to streamflow. This indicates that timing of agricultural management operations plays a role in agricultural pollutant runoff. Best management practices, such as pesticide use limits during wet seasons, could improve water quality in the Sacramento River watershed. The calibrated model establishes a modelling framework for further studies of hydrology, water quality and ecosystem protection in the study area. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

12.
Intensive agricultural practices on sensitive soils induce high erosion rates in central Belgium. Expert-rules models quantify runoff and erosion at catchment scale, avoiding over-parameterization, and can include some direct or indirect connectivity features. The aim of this article is to test the ability of an expert-based model, LandSoil, to quantify runoff and to locate erosion and sedimentation areas in a small cultivated loamy catchment in Belgium during the years 2014, 2015 and 2016. Spatialized data are important for assessing model outputs and the erosive response. Measurements of runoff and observation of spatial erosion/deposition patterns, especially around major connectivity points, permitted an assessment of the reliability of the model results. Runoff modelling gave contrasting results (good linear adjustment at the outlet of the 83 ha sub-catchment (point 1): r2 of 0.96, Nash–Sutcliffe criterion of 0.95; less good at the outlet of the 3.9 ha sub-catchment (point 2): r2 of 0.28, Nash–Sutcliffe criterion of –0.47). For point 2 the poor results are explained by the very few runoff events observed, a scaling effect and the small area with a single land use. Graduated rulers demonstrate that the model is able to provide a coherent pattern of erosion/deposition. The study highlights great sensitivity to the effect of land use, land allocation, landscape design and slope gradients. Grass strips induce deposition of eroded particles when slopes are gentle (< 2%). Woodland strips decrease connectivity by being in the stream but deposit thinner sediment layers. Field boundaries have a role in the transport, but not really the quantity, of sediments. This model validation in the Belgian loess context allows us to use LandSoil in other similar environments in order to estimate the effects of landscape management scenarios. © 2020 John Wiley & Sons, Ltd.  相似文献   

13.
Riparian buffer zones in agriculture dominated watersheds play important roles in reducing nonpoint source pollution into aquatic ecosystems and are widely used as a Best Management Practice. Assessment of the effectiveness of riparian buffer zones by modeling method is widely used for watershed management as field measurement‐based assessment is difficult and expensive. The integration of Riparian Ecosystem Management Model (REMM) and Soil and Water Assessment Tool (SWAT) has been developed to simulate the effect of nonpoint source pollution reduction by riparian buffer zones at subbasin scale. However, there are problems in using the integrated model at subbasin scale, as the size of subbasin partition could affect the pollutant reduction rate by riparian buffers. In this study, we partitioned a large watershed with size of 1331 ha into sub‐watersheds with sizes of 666, 333, 166, 83, 51, and 29 ha, and then compared the different simulation results. We found that the modeling could yield more convergent results when the sub‐watersheds were partitioned into suitable size. In the studied area, the suitable sub‐watershed size was less than about 166 ha for runoff and nitrogen and 83 ha for sediment and phosphorus. Among the eight sub‐watersheds (partitioned based on the size of 166 ha), results showed that the effects of riparian buffers on runoff and nutrient loading varied drastically. The reduction rate varied from 0.26% to 30.13% for runoff, 29.4% to 74.07% for sediment, 9.61% to 57.85% for nitrogen, and 18.61% to 68.12% for phosphorus, respectively.  相似文献   

14.
Model predictions concerning the endangerment of on‐site and off‐site damages due to runoff, soil erosion and sedimentation under alternative design and operation policies are of particular importance in recent catchment planning and management. By using the raster‐based model approach, linear landscape elements, such as streets and roads, and their impacts on flow paths are often neglected. Therefore, the aim of this study was to analyse the effects of linear landscape elements on patterns of soil erosion, sediment transport and sedimentation. To accomplish this, roads are considered while determining flow paths. Simulations in the well‐investigated catchment of the Wahnbach River (54 km²) in a low mountain range in Germany were carried out using a combination of different models for hydrology and soil erosion. Although the study focuses on the catchment scale of the Wahnbach River, detailed investigations concerning the sub‐catchment scale (21 ha) were also conducted. The simulation results show that these spatial structures mainly affect the pattern of soil erosion and sedimentation. On the sub‐catchment scale, improved identification of active zones for sediment dynamic becomes possible. On the catchment scale, the predicted runoff is about 20% higher, and sediment outputs were four times larger than predicted when roads were considered. Soil erosion increases by 37% whereas sedimentation is reduced by 29%. The model improvement could not be evaluated on the catchment scale because of the high variability and heterogeneity of land use and soils, but road impacts could be explained by simulations on the sub‐catchment scale. It can be concluded that runoff concentration due to rerouted flow paths leads to lower non‐concentrated and higher concentric‐linear surface runoff. Thus, infiltration losses decline and surface runoff and soil erosion increase because sedimentation is reduced. Further, runoff concentration can cause soil erosion hot spots. In the model concept used in this study, buffering of runoff and sediments on the upslope side of roads and in local depressions adjacent to roads cannot be simulated. Flow paths will only be rerouted because of road impacts, but the temporal ponding of water is not simulated. Therefore, the drastic increase of predicted sediment output due to road impact does not seem to be reliable. However, results indicate that the consideration of roads when determining flow paths enabled more detailed simulations of surface runoff, soil erosion and sedimentation. Thus, progress in model‐based decision‐making support for river catchment planning and management can be achieved. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

15.
Postfire runoff and erosion are a concern, and more data are needed on the effects of wildfire at the watershed‐scale, especially in the Colorado Front Range. The goal of this study was to characterize and compare the streamflow and suspended sediment yield response of two watersheds (Bobcat Gulch and Jug Gulch) after the 2000 Bobcat fire. Bobcat Gulch had several erosion control treatments applied after the fire, including aerial seeding, contour log felling, mulching, and straw wattles. Jug Gulch was partially seeded. Study objectives were to: (1) measure precipitation, streamflow, and sediment yields; (2) assess the effect of rainfall intensity on peak discharges, storm runoff, and sediment yields; (3) evaluate short‐term hydrologic recovery. Two months after the fire, a storm with a maximum 30 min rainfall intensity I30 of 42 mm h?1 generated a peak discharge of 3900 l s?1 km?2 in Bobcat Gulch. The same storm produced less than 5 l s?1 km?2 in Jug Gulch, due to less rainfall and the low watershed response. In the second summer, storms with, I30 of 23 mm h?1 and 32 mm h?1 generated peak discharges of 1100 l s?1 km?2 and 1700 l s?1 km?2 in the treated and untreated watersheds respectively. Maximum water yield efficiencies were 10% and 17% respectively, but 18 of the 23 storms returned ≤2% of the rainfall as runoff, effectively obscuring interpretation of the erosion control treatments. I30 explained 86% of the variability in peak discharges, 74% of the variability in storm runoff, and >80% of the variability in sediment yields. Maximum single‐storm sediment yields in the second summer were 370 kg ha?1 in the treated watershed and 950 kg ha?1 in the untreated watershed. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

16.
This paper investigates the effect of introducing spatially varying rainfall fields to a hydrological model simulating runoff and erosion. Pairs of model simulations were run using either spatially uniform (i.e. spatially averaged) or spatially varying rainfall fields on a 500‐m grid. The hydrological model used was a simplified version of Thales which enabled runoff generation processes to be isolated from hillslope averaging processes. Both saturation excess and infiltration excess generation mechanisms were considered, as simplifications of actual hillslope processes. A 5‐year average recurrence interval synthetic rainfall event typical of temperate climates (Melbourne, Australia) was used. The erosion model was based on the WEPP interrill equation, modified to allow nonlinear terms relating the erosion rate to rainfall or runoff‐squared. The model results were extracted at different scales to investigate whether the effects of spatially varying rainfall were scale dependent. A series of statistical metrics were developed to assess the variability due to introducing the spatially varying rainfall field. At the catchment (approximately 150 km2) scale, it was found that particularly for saturation excess runoff, model predictions of runoff were insensitive to the spatial resolution of the rainfall data. Generally, erosion processes at smaller sub‐catchment scales, particularly when the sediment generation equation had non linearity, were more sensitive to spatial rainfall variability. Introducing runon infiltration reduced the total runoff and sediment yield at all scales, and this process was also most sensitive to the rainfall resolution. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

17.
The pre‐calibrated and validated physically based watershed model, water erosion prediction project (WEPP) was used as a modelling tool for the identification of critical watersheds and evaluation of best management practices for a small hilly watershed (Karso) of India. The land use/cover of the study area was generated using IRS‐1C LISS‐III (linear imaging self scanner) satellite data. The watershed and sub‐watershed boundaries, drainage, slope and soil map of the study area were generated using ARC/INFO geographic information system (GIS). The WEPP model was finally applied to the Karso watershed which lies within Damodar Barakar catchment of India to identify the critical sub‐watersheds on the basis of their simulated average annual sediment yields. Priorities were fixed on the basis of ranks assigned to each critical sub‐watershed based on the susceptibility to erosion. The sub‐watershed having the highest sediment yield was assigned a priority number 1, the next highest value was assigned a priority number 2, and so on. Subsequently, the model was used for evaluating the effectiveness of best management practices (crop and tillage) for conservation of soil for all the sub‐watersheds. On the basis of this study, it is realized that cash crops like soyabean should be encouraged in the upland portion of the sub‐watersheds, and the existing tillage practice (country plough/mould board plough) may be replaced by a field cultivation system for conservation of soil and water in the sub‐watersheds. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

18.
Distributed, continuous hydrologic models promote better understanding of hydrology and enable integrated hydrologic analyses by providing a more detailed picture of water transport processes across the varying landscape. However, such models are not widely used in routine modelling practices, due in part to the extensive data input requirements, computational demands, and complexity of routing algorithms. We developed a two‐dimensional continuous hydrologic model, HYSTAR, using a time‐area method within a grid‐based spatial data model with the goal of providing an alternative way to simulate spatiotemporally varied watershed‐scale hydrologic processes. The model calculates the direct runoff hydrograph by coupling a time‐area routing scheme with a dynamic rainfall excess sub‐model implemented here using a modified curve number method with an hourly time step, explicitly considering downstream ‘reinfiltration’ of routed surface runoff. Soil moisture content is determined at each time interval based on a water balance equation, and overland and channel runoff is routed on time‐area maps, representing spatial variation in hydraulic characteristics for each time interval in a storm event. Simulating runoff hydrographs does not depend on unit hydrograph theory or on solution of the Saint Venant equation, yet retains the simplicity of a unit hydrograph approach and the capability of explicitly simulating two‐dimensional flow routing. The model provided acceptable performance in predicting daily and monthly runoff for a 6‐year period for a watershed in Virginia (USA) using readily available geographic information about the watershed landscape. Spatial and temporal variability in simulated effective runoff depth and time area maps dynamically show the areas of the watershed contributing to the direct runoff hydrograph at the outlet over time, consistent with the variable source area overland flow generation mechanism. The model offers a way to simulate watershed processes and runoff hydrographs using the time‐area method, providing a simple, efficient, and sound framework that explicitly represents mechanisms of spatially and temporally varied hydrologic processes. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

19.
This study develops improved Soil Moisture Proxies (SMP) based suspended sediment yield (SMPSY) models corresponding to three antecedent moisture conditions (AMCs) (i.e., AMC-I-AMC-III) by coupling the improved initial abstraction (Ia-λ) model, the SMA procedure and the SMP concept for modelling the rainfall generated suspended sediment yield. The SMPSY models specifically incorporate a watershed storage index (S) model to accentuate the transformation from storm to storm and to avoid the sudden jumps in sediment yield computation. The workability of the SMPSY models is tested using a large dataset of rainfall and sediment yield (98 storm events) from twelve small watersheds and a comparison has been made with the existing MSY model. The goodness-of-fit (GOF) statistics is evaluated in terms of the Nash Sutcliffe efficiency (NSE), and error indices, i.e., root mean square error (RMSE), normalized root mean square error (nRMSE), standard error (SE), mean absolute error (MAE), and RMSE-observations standard deviation ratio (RSR). The NSE values vary from 74.31% to 96.57% and from 75.21% to 91.78%, respectively for the SPMSY and MSY model. The NSE statistics indicate that the SMPSY model has lower uncertainty in simulating sediment yield as compared to the MSY model. The error indices are lower for the SMPSY model than the MSY model for most of the watersheds. These results show that the SMPSY model has less uncertainty and performs better than the MSY model. A sensitivity analysis of the SMPSY model shows that the parameter β is most sensitive followed by parameter S, α and A. Overall, the results show that the characterization of soil moisture variability in terms of SMPs and incorporation of improved delivery ratio and runoff coefficient relationship improves the simulation of the erosion and sediment yield generation process.  相似文献   

20.
Saturation‐excess runoff is the major runoff mechanism in humid well‐vegetated areas where infiltration rates often exceed rainfall intensity. Although the Soil and Water Assessment Tool (SWAT) is one of the most widely used models, it predicts runoff based mainly on soil and land use characteristics, and is implicitly an infiltration‐excess runoff type of model. Previous attempts to incorporate the saturation‐excess runoff mechanism in SWAT fell short due to the inability to distribute water from one hydrological response unit to another. This paper introduces a modified version of SWAT, referred to as SWAT‐Hillslope (SWAT‐HS). This modification improves the simulation of saturation‐excess runoff by redefining hydrological response units based on wetness classes and by introducing a surface aquifer with the ability to route interflow from “drier” to “wetter” wetness classes. Mathematically, the surface aquifer is a nonlinear reservoir that generates rapid subsurface stormflow as the water table in the surface aquifer rises. The SWAT‐HS model was tested in the Town Brook watershed in the upper reaches of the West Branch Delaware River in the Catskill region of New York, USA. SWAT‐HS predicted discharge well with a Nash‐Sutcliffe Efficiency of 0.68 and 0.87 for daily and monthly time steps. Compared to the original SWAT model, SWAT‐HS predicted less surface runoff and groundwater flow and more lateral flow. The saturated areas predicted by SWAT‐HS were concentrated in locations with a high topographic index and were in agreement with field observations. With the incorporation of topographic characteristics and the addition of the surface aquifer, SWAT‐HS improved streamflow simulation and gave a good representation of saturated areas on the dates that measurements were available. SWAT‐HS is expected to improve water quality model predictions where the location of the surface runoff matters.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号