首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Channel curvature produces secondary currents and a transverse sloping channel bed, along which the depth increases towards the outer bank. As a result deep pools tend to form adjacent to the outer bank, promoting bank collapse. The interaction of sediment grains with the primary and secondary flow and the transverse sloping bed also causes meanders to move different grain sizes in different proportions and directions, resulting in a consistent sorting pattern. Several models have been developed to describe this process, but they all have the potential to over‐predict pool depth because they cannot account for the influence of erodible banks. In reality, bank collapse might lead to the development of a wider, shallower cross‐section and any resulting flow depth discrepancy can bias associated predictions of flow, sediment transport, and grain‐size sorting. While bed topography, sediment transport and grain sorting in bends will partly be controlled by the sedimentary characteristics of the bank materials, the magnitude of this effect has not previously been explored. This paper reports the development of a model of flow, sediment transport, grain‐size sorting, and bed topography for river bends with erodible banks. The model is tested via intercomparison of predicted and observed bed topography in one low‐energy (5·3 W m?2 specific stream power) and one high‐energy (43·4 W m?2) study reach, namely the River South Esk in Scotland and Goodwin Creek in Mississippi, respectively. Model predictions of bed topography are found to be satisfactory, at least close to the apices of bends. Finally, the model is used in sensitivity analyses that provide insight into the influence of bank erodibility on equilibrium meander morphology and associated patterns of grain‐size sorting. The sensitivity of meander response to bank cohesion is found to increase as a function of the available stream power within the two study bends. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

2.
The erosion of a composite river bank critically depends on the erodibility of its fine soils, as the fine soil has higher resistance against erosion. Therefore, for the estimation of the bank erosion in the case of a composite river bank, it is important to determine the critical shear stress and erodibility coefficients of the bank soil and their spatial distribution. In the present study, erodibility parameters of the river bank of Brahmaputra in India have been estimated through 58 in situ submerged jet tests. The significance of spatial and layer‐wise distribution of the erodibility parameters was tested through analysis of variance (ANOVA). Results indicate that the spatial variation of erodibility parameters is highly significant, but layer‐wise variations of the erodibility parameters are not significant. Therefore, the erodibility of the riverbank depends on the particular location, whereas layer‐wise average erodibility parameters can be lumped for the estimation of the bank erosion for the specific site. Using the measured erodibility parameters, yearly river bank erosions at the study locations were computed and found to fall within the reported range of the bank erosion in the Brahmaputra River. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

3.
This paper analyses types and rates of change in river meander morphology and the links between mechanisms of change and emergent behaviour of planform morphology. It uses evidence of four dates of aerial photography combined with annual field mapping and ground photography to examine the morphological changes and mechanisms of change in a series of bends on an active meandering river, the River Dane in NW England, over a 25 year period. This unique data set allows insight into the spatial and temporal variability of bank line movement and component processes. Bank lines were mapped photogrametrically from air photos of 1984, 1996, 2001 and 2007 and the digitised courses compared in ArcGIS to produce calculations of erosional and depositional areas and rates. Most bends exhibit morphological change that largely follows the autogenic sequence, identified in qualitative models of meander development, from low sinuosity curves through simple symmetric and asymmetric bends to compound forms with lobe development in the apex region. Rates of erosion and bankline movement increase through this sequence until the compound phase. Relationships of amounts of movement to various curvature measures of bend morphology are complex. Several new loops, distinct from compound bend behaviour, have developed during the study period in formerly straight sections. Mechanisms of morphological change are illustrated for four types of bends: new, rapid growth bend; sharp‐angled bend with mid‐channel bar development; symmetric migrating bend; and simple to compound bend development. The changes take place in phases that are not simply related to discharge but to inherent sequences and feedbacks in development of bars and bend morphology and timescales for these are identified. Overall, emergent behaviour of systematic planform change, moderated by channel confinement and boundary features, is produced from spatially and temporally varied channel processes. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

4.
This study examined the temporal dynamics and longitudinal distribution of wood over a multi‐decadal timescale at the river reach scale (36 km) and a meander bend scale (300–600 m) in the Ain River, a large gravel‐bed river flowing through a forested corridor, and adjusting to regulation and floodplain land‐use change. At the 36 km scale, more wood was recruited by bank erosion in 1991–2000 than since the 1950s. The longitudinal distribution of accumulations was similar between 1989 and 1999, but in both years individual pieces occurred homogeneously throughout the reach, while jam distribution was localized, associated with large concave banks. A relationship between the mean number of pieces and the volume recruited by bank erosion (r2 = 0·97) indicated a spatial relationship between areas of wood production and storage. Wood mass stored and produced and channel sinuosity increased from 1993 to 2004 at three meander bends. Sinuosity was related to wood mass recruited by bank erosion during the previous decade (r2 = 0·73) and both of these parameters were correlated to the mean mass of wood/plot (r2 = 0·98 and 0·69 respectively), appearing to control wood storage and delivery at the bend scale. This suggests a local origin of wood stored in channel, not input from upstream trapped by preferential sites. The increase in wood since 1950 is a response to floodplain afforestation, to a change from braided to meandering channel pattern in response to regulation, and to recent large floods. We observed temporal stability of supply and depositional sectors over a decade (on a reach scale). Meander bends were major storage sites, trapping wood with concave banks, also delivering wood. These results, and the link between sinuosity and wood frequency, establish geomorphology as a dominant wood storage and recruitment control in large gravel‐bed rivers. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

5.
Catchment sediment budget models are used to predict the location and rates of bank erosion in tropical catchments draining to the Great Barrier Reef lagoon, yet the reliability of these predictions has not been tested due to a lack of measured bank erosion data. This paper presents the results of a 3 year field study examining bank erosion and channel change on the Daintree River, Australia. Three different methods were employed: (1) erosion pins were used to assess the influence of riparian vegetation on bank erosion, (2) bench‐marked cross‐sections were used to evaluate annual changes in channel width and (3) historical aerial photos were used to place the short term data into a longer temporal perspective of channel change (1972–2000). The erosion pin data suggest that the mean erosion rate of banks with riparian vegetation is 6·5 times (or 85%) lower than that of banks without riparian vegetation. The changes measured from cross‐section surveys suggest that channel width has increased by an average of 0·74 (±0·47) m a?1 over the study period (or ～0·8% yr?1). The aerial photo results suggest that over the last 30 years the Daintree River has undergone channel contraction of the order of 0·25 m a?1. The cross‐section data were compared against modelled SedNet bank erosion rates, and it was found that the model underestimated bank erosion and was unable to represent the variable erosion and accretion processes that were observed in the field data. The reach averaged bank erosion rates were improved by the inclusion of locally derived bed slope and discharge estimates; however, the results suggest that it will be difficult for catchment scale sediment budget models to ever accurately predict the location and rate of bank erosion due to the variation in bank erosion rates in both space and time. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

6.
《国际泥沙研究》2016,(2):131-138
Lateral migration is an important form of morphological changes on the Middle Yangtze River (MYR), particularly for the lower Jingjiang reach. The Three Gorges Reservoir (TGR) has substantially reduced sediment supply to the downstream river channels since its impoundment in June 2003. The scientific understanding of how decrease of sediment influences the processes of bank erosion and channel adjustments is complex and limited. In the present paper, the morphological responses in a typical meandering and island-braided river segment of the MYR to the filling of the TGR were investigated by a 3-D morphodynamic model. The potential of the 3-D model has been demonstrated by the observed data. The morphological evolutions in the Shishou bend during the first 12 years of the TGR impound-ment were predicted. The effects of the TGR operation on the planform evolutions in the study reach were analyzed based on the simulated results. Sediment load is decreased by 75%due to the early filling of the TGR. The magnitude of bed degradation with less sediment load due to the TGR operation is increased compared with the pre-dam situation. Qualitatively, the overall planform evolution trends in the Shishou bend after the TGR operation are similar to that without the TGR operation. The magnitude of lateral migration has been increased in some part of the channel bend, where the morphological response of the TGR operation exhibits more lateral migration rather than vertical degradation. Scouring at the bank toe enhances bank failure. Decrease of sediment load and weak bank anti-scour ability as well as the significant helical flow can be responsible for intensified bank erosion in the channel bend.  相似文献   

7.
The distal reach of the Lower Jingjiang River(LJR)in the middle of the Yangtze River consists of five adjacent bends,among which the Qigongling Bend is a U-shaped meander with a mean sinuosity of 2.2 and the narrowest neck 525 m in width.This bend is slowly approaching neck cutoff owing to progressive bank erosion.An abnormal phenomenon has occurred in this bend since the Three Gorges Reservoir(TGR)began to operate in 2003 which is erosion in the inner bank zone and deposition in the outer bank zone.This problem has not been fully understood because of the interplay of changes in water-sediment,bank erosion,and artificial bank revetment.In this study,aerial and remote sensing images,hydrological data,channel topography,and an existing bank erosion model are used to reveal channel morphodynamics of this bend and the trend of the potential neck cutoff induced by bank erosion.The study results show that the clear water released from the TGR has provided by forcefully eroded the point bar of inner bank but failed to scour the outer bank due to the protection of bank revetment since the 1990 s.Thus far,the outer bank zone near the bend apex has increasingly widened in conjunction with the formation of 2 emerging sand bars.Consequently,the thalweg of the main channel has laterally shifted toward the inner bank by roughly 800 m.More severely,the rate of bank retreat on the upstream side of the bend neck was about 4.5 m/yr in 2010-2019,but the downstream side of this neck was experienced slight deposition.Bank erosion could be accelerated by progressively increasing erosion and eventually trigger the occurrence of neck cutoff in the next few decades,thereby significantly altering the quasi-equilibrium regime of channel morphodynamics in the LJR.  相似文献   

8.
Compound meander bends with multiple lobes of maximum curvature are common in actively evolving lowland rivers. Interaction among spatial patterns of mean flow, turbulence, bed morphology, bank failures and channel migration in compound bends is poorly understood. In this paper, acoustic Doppler current profiler (ADCP) measurements of the three‐dimensional (3D) flow velocities in a compound bend are examined to evaluate the influence of channel curvature and hydrologic variability on the structure of flow within the bend. Flow structure at various flow stages is related to changes in bed morphology over the study timeframe. Increases in local curvature within the upstream lobe of the bend reduce outer bank velocities at morphologically significant flows, creating a region that protects the bank from high momentum flow and high bed shear stresses. The dimensionless radius of curvature in the upstream lobe is one‐third less than that of the downstream lobe, with average bank erosion rates less than half of the erosion rates for the downstream lobe. Higher bank erosion rates within the downstream lobe correspond to the shift in a core of high velocity and bed shear stresses toward the outer bank as flow moves through the two lobes. These erosion patterns provide a mechanism for continued migration of the downstream lobe in the near future. Bed material size distributions within the bend correspond to spatial patterns of bed shear stress magnitudes, indicating that bed material sorting within the bend is governed by bed shear stress. Results suggest that patterns of flow, sediment entrainment, and planform evolution in compound meander bends are more complex than in simple meander bends. Moreover, interactions among local influences on the flow, such as woody debris, local topographic steering, and locally high curvature, tend to cause compound bends to evolve toward increasing planform complexity over time rather than stable configurations. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

9.
The highly stochastic nature of riverbank erosion has driven the need for spatially explicit empirical models. Detailed bank profile surveys along a meander bend of the Brandywine Creek in Pennsylvania, USA, before and after 28 high flow events over a 2·5 year period are used to develop an empirical model of cohesive bank profile erosion. Two hundred and thirty‐six bank erosion observations are classified as hydraulic erosion or subaerial erosion. Threshold conditions required to initiate bank erosion cannot be defined based on field measurements. Using the near‐bank velocity and the number of freeze–thaw cycles as predictors, regression equations are derived for hydraulic erosion that specify the length, thickness, and location on the bank face of eroded blocks. An empirical discriminant function defines the critical geometry of overhang failures, and the volumes removed by overhang failures are computed using another regression equation. All the regression equations are significant, but have low correlation coefficients, suggesting that cohesive bank erosion has a strong stochastic component. Individual events typically remove small masses of soil (average volume 0·084 m3/m) a few centimeters thick (median = 0·057 m) and a few decimeters in length (median = 0·50 m) from the lower third of the bank. Hydraulic erosion is responsible for 87% of all erosion. When applied to three survey sites not used in its development, the profile model predicts the total volume of erosion with errors of 23%, 5% and 1%. Twenty‐four percent of computed erosion volumes for single events are within 50% of observed volumes at these three sites. Extending the approach to decadal timescales and to entire bends will require three‐dimensional observations of bank failure, and spatially and temporally explicit methods to account for the influence of individual large trees on bank failures and near‐bank hydraulic processes. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

10.
Channel bars and banks strongly affect the morphology of both braided and meandering rivers. Accordingly, bar formation and bank erosion processes have been greatly explored. There is, however, a lack of investigations addressing the interactions between bed and bank morphodynamics, especially over short timescales. One major implication of this gap is that the processes leading to the repeated accretion of mid‐channel bars and associated widenings remain unsolved. In a restored section of the Drau River, a gravel‐bed river in Austria, mid‐channel bars have developed in a widening channel. During mean flow conditions, the bars divert the flow towards the banks. One channel section exhibited both an actively retreating bank and an expanding mid‐channel bar, and was selected to investigate the morphodynamic processes involved in bar accretion and channel widening at the intra‐event timescale. We repeatedly surveyed riverbed and riverbank topography, monitored riverbank hydrology and mounted a time‐lapse camera for continuous observation of riverbank erosion processes during four flow events. The mid‐channel bar was shown to accrete when it was submerged during flood events, which at the subsequent flow diversion during lower discharges narrowed the branch along the bank and increased the water surface elevation upstream from the riffle, which constituted the inlet into the branch. These changes of bed topography accelerated the flow along the bank and triggered bank failures up to 20 days after the flood events. Four analysed flow events exhibited a total bar expansion from initially 126 m2 to 295 m2, while bank retreat was 6 m at the apex of the branch. The results revealed the forcing role of bar accretion in channel widening and highlighted the importance of intra‐event scale bed morphodynamics for bank erosion, which were summarized in a conceptual model of the observed bar–bank interactions. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

11.
Between a.d. 2006 and 2008, we completed annual surveys of two mercury‐contaminated eroding banks, one forested and the other grass covered, along the gravel‐bed, bedrock South River in Virginia. Gridded digital terrain models with a resolution of 0·05 m were created from bank topography data collected using a terrestrial laser scanner. Model comparisons indicate that the forested bank retreated nearly 1 m around two leaning trees, while elsewhere the extent of bank retreat was negligible. On the grassy bank, retreat was controlled by the creation of small overhanging clumps of turf at the top of the bank, their occasional failure, and the ultimate removal of failed debris from the bank toe. Partial autocorrelation analysis of vertically integrated bank retreat demonstrates that bank profile erosion is virtually uncorrelated at horizontal distances greater than about 1 m on both banks, a length scale of approximately half the bank height. This extensive streamwise variability suggests that widely spaced profile data cannot adequately represent bank erosion at these sites. Additional analysis of our comprehensive spatial data also indicates that traditional bank profile surveys with any spacing greater than 1 m would result in measurement errors exceeding 10%, an important conclusion for assessing annual rates of mercury loading into the South River from bank erosion. Our results suggest that three‐dimensional gridded bare‐earth models of bank topography may be required to accurately measure annual bank retreat in similar river systems. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

12.
The braided Jamuna River frequently changes its courses.Sometimes the secondary channel in a braided river acts as a single thread meandering channel.In the present study an attempt has been made to investigate the flow patterns and to estimate the rate of bank erosion in a bend along the Jamuna River.The three dimensional(3D) flow velocities were measured using Acoustic Doppler Current Profiler(ADCP).It is found that the near bank velocity is amplified by 1.1 to 1.3 times as compared with the section averaged velocity.A dominant secondary current is found in the upstream bend.The evolution as well as decay of the secondary current is not as clear as it is found in the laboratory experiments.It is revealed from the analysis of the flow process that the causes of higher rate of erosion at the study bend are the oblique flow near bankline,six times amplified shear velocity than critical shear velocity near bankline and the secondary current which acts as a sediment transporting agent from the outer bank towards the inner bank or the sand bar.Based on the flow processes,a simplified erosion prediction model is developed and applied to estimate the rate of erosion at a selected bend.Finally the predicted results have been compared with the observed data at the bend and all the available data at other bends along the Jamuna River.  相似文献   

13.
This paper presents a three-dimensional (3-D) numerical model to simulate morphological changes in alluvial channels due to bank erosion. A method for the simulation of bank erosion is established. This is incorporated into a 3-D mathematical model for turbulent flow and non-uniform, non-equilibrium sediment transport. This model is applied to simulate morphological changes in the Shishou bend of the middle Yangtze River in China, where serious bank erosions occurred during the last two decades. The double-layer sediment structure of the riverbank on the middle Yangtze River is taken into account in the bank erosion module. Both cohesive and non-cohesive bank material in the different layers are considered. The bank erosion module also includes other factors affecting the rate of bank erosion, such as the longitudinal length of failed bank, the thickness of each layer in the double-layer structure, and the erosion-resisting effect of cohesive material from the top layer of failed bank. A locally-adaptive grid system is proposed to efficiently simulate the lateral migration of alluvial channel due to bank erosion. The predictive capability of the 3-D model is examined by laboratory data. Simulated processes of bank erosion agree with field observations in the Shishou bend during the period of October 1996–October 1998, and the bank erosion module plays a significant role in simulating morphological changes of the study reach. In addition, the equivalent channel-forming discharge, which is defined as a constant discharge that can create the same amount of bank erosion in an alluvial channel as that created by natural runoff processes during the same period of time, is proposed to improve calculation efficiency for feasibility studies.  相似文献   

14.
Meander bends of many large, sand‐bed meandering rivers are partitioned by chute channels that convey permanent flow, and co‐exist with the mainstem for decades. As a first step toward understanding the dynamics and morphodynamic implications of these ‘bifurcate meander bends’, this study applied binary logistic regression analysis to determine whether it is possible to predict chute initiation based on attributes of meander bend character and dynamics. Regression models developed for the Strickland River, Papua New Guinea, the lower Paraguay River, Paraguay/Argentina, and the Beni River, Bolivia, revealed that the probability of chute initiation at a meander bend is a function of the bend extension rate (the rate at which a bend elongates in a direction perpendicular to the valley axis trend). Image analyses of all rivers and field observations from the Strickland suggest that the majority of chute channels form during scroll–slough development. Rapid extension is shown to favour chute initiation by breaking the continuity of point bar deposition and vegetation encroachment at the inner bank, resulting in widely‐spaced scrolls with intervening sloughs that are positively aligned with primary over‐bar flow. The rivers plot in order of increasing chute activity on an empirical meandering‐braided pattern continuum defined by potential specific stream power (ωpv) and bedload calibre (D50). Increasing stream power is considered to result in higher bend extension rates, with implications for chute initiation. In addition, chute stability is shown to depend on river sediment load relative to flow discharge (Qs/Q), such that while the Beni may plot in the region of highly braided rivers by virtue of a high potential specific stream power, the formation of stable chute channels is suppressed by the high sediment load. This tendency is consistent with previous experimental studies, and results in a planform that is transitional between single‐thread meandering and braided. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

15.
The lake levels in Lake Michigan‐Huron have recently fallen to near historical lows, as has the elevation difference between Lake Michigan‐Huron compared to Lake Erie. This decline in lake levels has the potential to cause detrimental impacts on the lake ecosystems, together with social and economic impacts on communities in the entire Great Lakes region. Results from past work suggest that morphological changes in the St Clair River, which is the only natural outlet for Lake Michigan‐Huron, could be an appreciable factor in the recent trends of lake level decline. A key research question is whether bed erosion within the river has caused an increase in water conveyance, therefore, contributed to the falling lake level. In this paper, a numerical modeling approach with field data is used to investigate the possibility of sediment movement in the St Clair River and assess the likelihood of morphological change under the current flow regime. A two‐dimensional numerical model was used to study flow structure, bed shear stress, and sediment mobility/armoring over a range of flow discharges. Boundary conditions for the numerical model were provided by detailed field measurements that included high‐resolution bathymetry and three‐dimensional flow velocities. The results indicate that, without considering other effects, under the current range of flow conditions, the shear stresses produced by the river flow are too low to transport most of the coarse bed sediment within the reach and are too low to cause substantial bed erosion or bed scour. However, the detailed maps of the bed show mobile bedforms in the upper St Clair River that are indicative of sediment transport. Relatively high shear stresses near a constriction at the upstream end of the river and at channel bends could cause local scour and deposition. Ship‐induced propeller wake erosion also is a likely cause of sediment movement in the entire reach. Other factors that may promote sediment movement, such as ice cover and dredging in the lower river, require further investigation. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

16.
River banks are important sources of sediment and phosphorus to fluvial systems, and the erosion processes operating on the banks are complex and change over time. This study explores the magnitude of bank erosion on a cohesive streambank within a small channelized stream and studies the various types of erosion processes taking place. Repeat field surveys of erosion pin plots were carried out during a 4‐year period and observations were supplemented by continuous monitoring of volumetric soil water content, soil temperature, ground water level and exposure of a PEEP sensor. Bank erosion rates (17·6–30·1 mm year?1) and total P content on the banks were relatively high, which makes the bank an important source of sediment and phosphorus to the stream, and it was estimated that 0·27 kg Ptot year?1 ha?1 may potentially be supplied to the stream from the banks. Yearly pin erosion rates exceeding 5 cm year?1 were mainly found at the lower parts of the bank and were associated with fluvial erosion. Negative erosion pin readings were widespread with a net advance of the bank during the monitoring period mainly attributed to subaerial processes and bank failure. It was found that dry periods characterized by low soil water content and freeze–thaw cycles during winter triggered bank failures. The great spatial variability, in combination with the temporal interaction of processes operating at different scales, requires new tools such as 3‐D topographical surveying to better capture bank erosion rates. An understanding of the processes governing bank erosion is required for riparian management using vegetational measures as root size and structure play different roles when it comes to controlling bank erosion processes. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

17.
There is a paucity of data and insight in the mechanisms of, and controls on flow separation and recirculation at natural sharply‐curved river bends. Herein we report on successful laboratory experiments that elucidate flow structure in one constant‐width bend and a second bend with an outer‐bank widening. The experiments were performed with both a flat immobile gravel bed and mobile sand bed with dominant bedload sediment transport. In the constant‐width bend with immobile bed, a zone of mainly horizontal flow separation (vertical rotational axis) formed at the inner bank that did not contain detectable flow recirculation, and an outer‐bank cell of secondary flow with streamwise oriented rotational axis. Surprisingly, the bend with widening at the outer bank and immobile bed did not lead to a transverse expansion of the flow. Rather, flow in the outer‐bank widening weakly recirculated around a vertical axis and hardly interacted with the inner part of the bend, which behaved as a constant‐width bend. In the mobile bed experiment, downstream of the bend apex a pronounced depositional bar developed at the inside of the bend and pronounced scour occurred at the outside. Moreover the deformed bed promoted flow separation over the bar, including return currents. In the constant‐width bend, the topographic steering impeded the generation of an outer‐bank cell of secondary flow. In the bend with outer‐bank widening, the topographic steering induced an outward expansion of the flow, whereby the major part of the discharge was conveyed in the central part of the widening section. Flow in the outer‐bank widening was highly three dimensional and included return currents near the bottom. In conclusion, the experiments elucidated three distinct processes of flow separation common in sharp bends: flow separation at the inner bank, an outer‐bank cell of secondary flow, and flow separation and recirculation in an outer‐bank widening. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

18.
The effects of aquatic macrophytes on flow and turbulence were studied in a tightly curving meander bend. Three field measurement campaigns were carried out within a one year period to capture effects of seasonal changes in macrophyte cover. They comprised three‐dimensional velocity measurements and mappings of vegetation cover and bathymetry. Flow accelerates and converges over the run into an axial pool in a jet‐like flow pattern bordered by outer and inner bank flow separation zones. The jet and widening of the cross‐section anticipate helical flow until the second half of the bend, where an asymmetric pool developed. Submerged vegetation at the riffles preserves the jet at much lower discharges during the summer period by concentrating high momentum fluid near the surface. Plants locally modify the velocity and stress patterns, reduce bed shear stresses, create zones of fine sediment accumulation and reinforce the bed and banks with roots and rhizomes. Plant patches colonising the banks and the point bar confine secondary flow cells laterally and affect shape and magnitude of the transverse flow profiles near their edges. The morphology of the bend was very stable over the observation period and neither bank erosion nor pool scouring occurred. However, fine sediments accumulate within vegetation patches and in the recirculation zones while the remaining open areas tend to erode slightly. With the decay of macrophytes in winter, sediment accumulations are mobilised again and the bathymetry levels, supporting cyclic models of morphologic change in vegetated bends. In the second part of the paper, semi‐empirical models for the three predominant flow types were tested and discussed; velocity and stress models of vegetated mixing layers and plane turbulent jets, and Rozovskii's model for the transverse flow in bends. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

19.
The present work explores relations between stream power,braiding intensities and bank erosion in certain stretches of the Brahmaputra River.In this paper,an objective approach is presented to enable quantitative assessment of spatio-temporal behaviour of channel braiding process of the Brahmaputra River by using the Plan Form Index and corresponding estimation of stream power to establish a behavioural pattern of variability of potential energy expenditure.The braiding index is compared for discrete years to understand the morphological behaviour.Subsequently,a real time estimation of stream power for certain stretches of Brahmaputra River is done in order to analyse its variability in braiding intensity and bank erosion.The paper presents the dynamic behaviour of the channel pattern of the Brahmaputra River System in Assam valley of India over a time span of 18 years.The procedure addresses the selection of input parameters from digital satellite images,comprising scenes for the years 1990,1997 and 2007 with specific dates,from Dhubri near Indo-Bangladesh Border to Upper Assam.Deployment of GIS technique has been made to extract the required parameters to derive Plan Form Indices for the entire study reach.Stream power estimation is done for corresponding latest floods and for corresponding dates of image scenes.The study indicated that due to consistent aggradation of riverbed inducing temporal declination of stream power,there is an occurrence of wide spread braiding.This in turn incurs substantial yearly land loss due to bank erosion,caused by flow concentrations due to temporal evolution of multiple channels in the Brahmaputra River.  相似文献   

20.
A depth‐averaged linearized meander evolution model was calibrated and tested using the field data collected at the Quinn River in the Black Rock Desert, Nevada. Two approaches used to test the model were: (1) simulating meander evolution and comparing the results with the observed 38 year migration pattern; and (2) fitting the model parameters to present bank asymmetry (the ratio of the maximum bank gradients on opposite sides of the channel). The data required as input were collected in the field during a high flow in May 2011 and from aerial photographs and LiDAR data. Both approaches yielded similar results for the best fit parameter values. The bank asymmetry analysis showed that the bank asymmetry and the velocity perturbation have high correlation at close to zero spatial lag while the maximum correlation between the bank asymmetry and maximum bend curvature is offset by about 25 m. The model sufficiently replicated 38 years of channel migration, with a few locations significantly under‐ or over‐predicted. Inadequacies of the flow model and/or variation in bank properties unaccounted for are most likely the causes for these discrepancies. Flow through the Quinn River was also simulated by a more general 3D model. The downstream pattern of near‐bank shear stresses simulated by the 3D model is nearly identical to those resulting from the linearized flow model. Topographic profiles across interior bends are essentially invariant over a wide range of migration rates, suggesting that the traditional formulation that cut bank erosion processes govern migration rates is appropriate for the Quinn River. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号