共查询到20条相似文献，搜索用时 31 毫秒
1.
Two dynamic centrifuge model tests were performed to simulate dry or saturated sand deposits subjected to 1 Hz base shaking. This experimental study investigated the boundary effects of a laminar container on the seismic response acquired from accelerometers and from pore pressure transducers, both of which were embedded in the sand bed at various depths and distances from the end walls. Under the tested configurations and the employed input motion used in the study, the test results revealed minimal boundary effects on the seismic responses. The measured maximum amplitude, main frequencies, phase lags of acceleration, and the profiles of the calculated RMS acceleration amplification factor were not affected by the boundaries if the instruments were positioned at a distance of more than one-twentieth of the model length from the end walls and were not positioned on the ground surface. No obvious discrepancies were observed in the time histories of excess pore water pressure, measured at a distance of one-fourth of the model length from the end walls. These results infer that variations in the seismic response at the end walls were minimal; hence the laminar container used in the study may be used effectively to simulate 1D shear wave propagation in centrifuge shaking table tests. However, for other testing configurations, a similar study should be undertaken for evaluating the boundary effect of the laminar container on the seismic responses. 相似文献
2.
This paper presents the results of dynamic centrifuge model tests conducted to investigate the liquefaction mechanism in non-homogeneous soil deposits. Four types of model tests were conducted: one model test involved a uniform soil deposit; one involved continuous layered soil deposit; and two involved discontinuous layered soil deposits. Non-homogeneity in the tests was incorporated by including periodically distributed discontinuous silty sand patches. It was found that more excess pore water pressure (EPWP) remains for a longer period of time in the discontinuous region in non-homogeneous soil deposits compared with the continuous layered and uniform soil deposits. The generation of pore water pressure ceases the supply of a new mass of water after seismic excitation; therefore the dissipation of EPWP becomes the dominant factor for settlement after seismic excitation. The rapid dissipation of EPWP through the discontinuous part in the non-homogeneous soil deposits manifests as a larger settlement in the discontinuous part, causing non-uniform settlements. 相似文献
3.
基于ABAQUS软件平台,应用自行开发的流固耦合动力模型孔压单元模拟场地土体,并通过黏弹性人工边界方法实现地震动的输入,对饱和土体场地中的双孔隧道结构在地震荷载作用下的动力反应进行研究。计算结果表明:在地震反应结束时刻,场地土体位移幅值在两隧道之间以及两隧道的附近区域较大,而远离隧道的区域则较小;场地底部区域土体的孔压幅值较大,而场地顶部区域土体则较小;隧道左右两侧拱腰部位的衬砌的应力较大,而拱顶部位则较小。计算结果同时表明了流固耦合动力模型孔压单元在饱和土体-隧道体系地震反应研究中的适用性。 相似文献
4.
The effects of earthquakes on cantilever retaining walls with liquefiable backfills were studied. The experimental techniques utilized in this study are discussed here. A series of centrifuge tests was conducted on aluminum, fixed-base, cantilever wall models retaining saturated, cohesionless backfills. Accelerations on the walls and in the backfill, static and excess pore pressures in the soil, and deflections and bending strains in the wall were measured. In addition, direct measurements of static and dynamic lateral earth pressures were made. In some tests, sand backfills were saturated with the substitute pore fluid metolose. Modeling of model type experiments were conducted. The experimental measurements were found internally consistent and repeatable. Both static and dynamic earth pressure measurements were determined to be reliable. It was also observed that for the test configuration adopted, a special boundary treatment such as the use of duxseal is optional. Static and seismic modeling of models were also successful, which indicated that the assumed scaling relations were essentially correct. 相似文献
5.
An analytical model is developed to analyze the seismic response of gravity walls retaining and founded on dry sand, with special emphasis on tilting behaviour. A well verified two-dimensional finite element code is used for this purpose. The analytical model is verified by comparing predictions to results from three dynamic centrifuge tests, with satisfactory agreement. Moreover, sensitivity analyses are carried out for one of the centrifuge test conditions to understand how the results would change if the boundary conditions and rotational stiffness of the wall were changed. 相似文献
6.
A transparent Flexible Shear Beam (FSB) container was designed and constructed to simulate the dynamic response of a stratum of soil under horizontal, one-dimensional (1-D) earthquake shaking in a geotechnical centrifuge. A stack of four rectangular, acrylic frames separated by layers of flexible, high-strength rubber was used to form the transparent container. The fundamental natural frequency of the container was estimated to be similar to a layer of sand in its softened or liquefied state. The suitability of the container in simulating 1-D site response with minimal boundary effects was evaluated by monitoring the uniformity of the induced accelerations and settlements across the soil specimen. Further, the measured lateral displacements were compared with equivalent-linear site response analyses. The new FSB container was found to provide satisfactory boundary conditions for studying complex Soil–Structure-Interaction problems, while simultaneously enabling researchers to visualize deformations of the soil and buried structures during shaking. 相似文献
7.
Understanding the soil–structure interaction (SSI) mechanism is crucial in the seismic design of nuclear power plant (NPP) containment systems. Although the numerical analysis method is generally used in seismic design, there is a need for experimental verification for the reliable estimation of SSI behavior. In this study a dynamic centrifuge test was performed to simulate the SSI behavior of a Hualien large-scale seismic test (LSST) during the Chi-Chi earthquake. To simulate the soil profile and dynamic soil properties of the Hualien site, a series of resonant column (RC) tests was performed to determine the model soil preparation conditions, such as the compaction density and the ratio of soil–gravel contents. The variations in the shear wave velocity (VS) profiles of the sand, gravel, and backfill layers in the model were estimated using the RC test results. During the centrifuge test, the VS profiles of the model were evaluated using in-flight bender element tests and compared with the in-situ VS profile at Hualien. The containment building model was modeled using aluminum and the proper scaling laws. A series of dynamic centrifuge tests was performed with a 1/50 scale model using the base motion recorded during the Chi-Chi-earthquake. In the soil layer and foundation level, the centrifuge test results were similar to the LSST data in both the time and frequency domains, but there were differences in the structure owing to the complex structural response as well as the material damping difference between the concrete in the prototype and aluminum in the model. In addition, as the input base motion amplitude was increased to a maximum value of 0.4g (prototype scale), the responses of the soil and containment model were measured. This study shows the potential of utilizing dynamic centrifuge tests as an experimental modeling tool for site specific SSI analyses of soil–foundation–NPP containment system. 相似文献
8.
A two-dimensional (2D) finite element analytical model is developed to analyze the seismic response of rigid highway bridge abutments, retaining and founded on dry sand. A well verified finite element code named FLEX is used for this purpose. The proposed model has the following characteristics: (1) The soil (dry sand in this study) is modeled by a 2D finite element grid; (2) The bridge abutment is molded as a rigid substructure; (3) The strength and deformation of the soil are modeled using the viscous cap constitutive model. This model consists of a failure surface and hardening cap together with an associated flow rule. The cap surface is activated for the soil under the wall to represent compaction during wall rocking. In addition, viscoelastic behavior is provided for representing the hysteretic-like damping of soil during dynamic loading; (4) Interface elements are used between the wall and the soil (at the backface of the wall and under its base) to allow for sliding and for debonding/recontact behavior; (5) The finite element grid is truncated by using an absorbing boundary approximation. Using this boundary at both sides of the grid simulates the horizontal radiation of energy scattered from the wall and the excavation. Shear beams are placed adjacent to the lateral boundaries from each side which give the far-field ground motion, for comparison with those computed adjacent to the boundaries. The analytical model is verified comparing predictions to results from dynamic centrifuge tests, with satisfactory agreement. The proposed model is used to study the dynamic response of an 8.0 m high and 3.0 m wide rigid bridge abutment (proportioned using the traditional approach to design) for different sinusoidal and earthquake acceleration input motions. The results from the analysis show that outward tilting of rigid bridge abutments is the dominant mode of response during dynamic shaking and that these abutments end up with a permanent outward tilt at the end of shaking. The results from all the analyzed cases of the 8.0 m high gravity retaining wall together with those from the analysis of the tilting wall centrifuge tests are discussed and used for proposing a practical method for evaluating the seismic response of rigid abutments during earthquakes. 相似文献
9.
地下结构物抗震稳定性的研究具有重要实际意义。基于动态土工离心试验,应用有效应力法分析了不同水平地震作用下土层和地下RC结构物的最大水平位移、不同埋深的土层加速度和超孔隙水压力变化规律,以及结构物的破坏发展特征,并进一步与试验结果进行了相互验证和对比,取得了较好效果,为重要地下结构物的抗震设计提供了依据和参考。 相似文献
10.
Three dynamic centrifuge model tests were conducted at an acceleration of 80g to simulate the seismic responses of level sand deposits: an intra-silt layer was embedded in two of these sand deposits at different depths. The effects of a low-permeability intra-silt layer on the build-up and dissipation of excess pore-water pressure, surface settlement, and the related liquefaction mechanism were investigated. An intra-silt layer modifies the seismic response of the sand deposit, reduces the extent of liquefaction, and thus decreases surface settlement. The depth of the intra-silt layer is one of the factors influencing the seismic responses of the sand deposits. The magnitude of the surface settlement is proportional to the degree of liquefaction in the sand deposit. The high positive hydraulic gradients appearing in both the intra-silt layer and in the sand deposit lying on the intra-silt layer can break a thinner or weaker top layer and result in sand boiling. Our visual animation of the ratio of the excess pore-water pressure and the lateral displacement revealed that the liquefaction front travels upward during shaking and the solidification front travels upward after shaking. 相似文献
11.
This paper outlines the results of an experimental program carried out on centrifuge models of cantilevered and propped retaining walls embedded in saturated sand. The main aim of the paper is to investigate the dynamic response of these structures when the foundation soil is saturated by measuring the accelerations and pore pressures in the soil, displacements and bending moment of the walls. A comparison among tests with different geometrical configurations and relative density of the soil is presented. The centrifuge models were subjected to dynamic loading in the form of sinusoidal accelerations applied at the base of the models. This paper also presents data from pressure sensors used to measure total earth pressure on the walls. Furthermore, these results are compared with previous dynamic centrifuge tests on flexible retaining walls in dry sand. 相似文献
12.
To investigate the seismic response of a pile group during liquefaction, shaking table tests on a 1/25 scale model of a 2 × 2 pile group were conducted, which were pilot tests of a test project of a scale-model offshore wind turbine with jacket foundation. A large laminar shear box was utilized as the soil container to prepare a liquefiable sandy ground specimen. The pile group model comprising four slender aluminum piles with their pile heads connected by a rigid frame was designed with similitude considerations focusing on soil–pile interaction. The input motions were 2-Hz sinusoids with various acceleration amplitudes. The excess pore water pressure generation indicated that the upper half of the ground specimen reached initial liquefaction under the 50-gal-amplitude excitation, whereas in the 75-gal-amplitude test, almost entire ground was liquefied. Accelerations in soil, on the movable frames composing the laminar boundary of the shear box, and along the pile showed limited difference at the same elevation before liquefaction. After liquefaction, the soil and the movable-frame accelerations that represented the ground response considerably reduced, whereas both the movable frames and the piles exhibited high-frequency jitters other than 2-Hz sinusoid, and meantime, remarkable phase difference between the responses of the pile group and the ground was observed, all probably due to the substantial degradation of liquefied soil. Axial strains along the pile implied its double-curvature bending behavior, and the accordingly calculated moment declined significantly after liquefaction. These observations demonstrated the interaction between soil and piles during liquefaction. 相似文献
13.
In this paper, a fundamental assessment of the method of physical wave-absorbing boundary and centrifuge modeling is presented in the context of experimental simulations of seismic free-field ground motion. Focusing on the characteristics of a sand stratum, a series of seismic tests on models of uniform density and a large width-to-depth ratio with Duxseal as the side boundary were performed using an in-box shake-table system. By means of the transfer function approach in the frequency domain, the complex three-dimensional nature of the dynamic response of the finite soil model with the boundary treatment is demonstrated in terms of its variable resonant frequency distribution at different g-levels. Apart from being helpful in quantifying the difficulty in interpreting the finite-domain response simulations using one-dimensional theories or homogenized representations, the measured data substantiates the need and usefulness of coupling the Duxseal boundary approach with a three-dimensional elastodynamic synthesis. With the aid of a corresponding boundary element implementation, the feasibility of identifying the soil's in-flight shear modulus variation, Poisson's ratio and horizontal-to-vertical earth pressure ratio from the centrifuge model's free-field measurements is also explored. 相似文献
14.
In this paper, a Hilbert-Huang Transform data-processing technique is successfully used to characterize the seismic responses of soil–quay wall systems using measured data in a series of geotechnical centrifuge shaking-table tests. The predominant frequency of a liquefied deposit shifts down to a low frequency level; however, “de-liquefaction” leads to frequent, local higher-frequency spikes in the time histories of predominant instantaneous frequency (PIF). A lower amount of seaward displacement was found if the combined translation and rotation modes resulted in lower excess-pore-water pressure when the wall accelerated seaward. Cyclic changes in the PIF of the wall during shaking are directly related to the stiffness of the soil in which the wall is embedded. Thus, PIF at any given instant provides a superior indicator for characterizing the occurrence of liquefaction and the time-varying soil dynamic property. This advantage assists in evaluating the degradation of soil dynamic properties at any given instant based on the acceleration time histories measured in model tests or even in the field. 相似文献
15.
Centrifuge modeling of seismic response of layered soft clay 总被引：1，自引：0，他引：1
Centrifuge modeling is a valuable tool used to study the response of geotechnical structures to infrequent or extreme events
such as earthquakes. A series of centrifuge model tests was conducted at 80g using an electro-hydraulic earthquake simulator mounted on the C-CORE geotechnical centrifuge to study the dynamic response
of soft soils and seismic soil–structure interaction (SSI). The acceleration records at different locations within the soil
bed and at its surface along with the settlement records at the surface were used to analyze the soft soil seismic response.
In addition, the records of acceleration at the surface of a foundation model partially embedded in the soil were used to
investigate the seismic SSI. Centrifuge data was used to evaluate the variation of shear modulus and damping ratio with shear
strain amplitude and confining pressure, and to assess their effects on site response. Site response analysis using the measured
shear wave velocity, estimated modulus reduction and damping ratio as input parameters produced good agreement with the measured
site response. A spectral analysis of the results showed that the stiffness of the soil deposits had a significant effect
on the characteristics of the input motions and the overall behavior of the structure. The peak surface acceleration measured
in the centrifuge was significantly amplified, especially for low amplitude base acceleration. The amplification of the earthquake
shaking as well as the frequency of the response spectra decreased with increasing earthquake intensity. The results clearly
demonstrate that the layering system has to be considered, and not just the average shear wave velocity, when evaluating the
local site effects. 相似文献
16.
Design and commissioning of a laminar soil container for use on small shaking tables 总被引：2，自引：0，他引：2
This paper describes the design, fabrication and commissioning of a single axis laminar shear box for use in seismic soil–structure interaction studies. A laminar shear box is a flexible container that can be placed on a shaking table to simulate vertical shear-wave propagation during earthquakes through a soil layer of finite thickness. The laminar shear box described in this paper was designed to overcome the base shear limitations of a small shaking table at The University of Western Ontario. The design details of the box are provided in addition to results of dynamic tests performed to commission the box. A synthetic clay comprising sodium bentonite mixed with diluted glycerin was used as the model soil and 1-G similitude theory was employed to maintain model to prototype similarity. The model soil was compacted into the container in lifts to achieve soil stiffness that increased with depth. A series of shaking table tests and numerical analyses that were performed to study the performance of the laminar box and non-linear seismic behavior of the model clay are described. The results of this study show that the laminar box does not impose significant boundary effects and is able to maintain 1-D soil column behavior. In addition, the dynamic behavior of the model clay during scaled model tests was found to be consistent with the behavior measured during cyclic laboratory tests. 相似文献
17.
This study attempts to propose dynamic centrifuge model tests as a method of seismic risk assessment in order to discover how stone architectural heritages with masonry structures have endured seismic load, and whether there is any possibility of future earthquake damage. Dynamic centrifuge tests have been conducted for one fifteenth scale models of Seok-ga-tap and the five-storey stone pagoda of Jeongnimsa temple site, which are Korean representative stone pagodas. In order to make input motions of the earthquake simulator, site investigation and site-specific response analysis have been performed. The models of two stone pagodas, which have the same number of pieces with the real structures, have been produced and the dynamic centrifuge tests have been conducted for the model pagodas. Accelerometers were attached at different heights of the pagoda. The measured acceleration records and frequency responses were analysed during dynamic centrifuge test. Two real earthquake records, Hachinohe and Ofunato earthquakes and a sweeping signal with ranged frequency were utilised for input motions of dynamic centrifuge tests to evaluate the behaviour of the stone pagodas. For Seok-ga-tap models, it was observed that acceleration tends to be amplified with height. The third floor body shows at most 2.5 amplification of acceleration in comparison to the surface ground. The amplification was at a frequency of 3.83 Hz and it was considered as the natural frequency of the pagoda. For the five-storey stone pagoda, the seismic wave energy significantly reduced while it passed the first body floor, and then the peak acceleration was gradually amplified upwards. It was found that the pagodas did not collapse when the peak acceleration of ground surface was raised to 0.4 g. Given that the maximum design seismic acceleration specified in Korean seismic design guide is 0.22 g and the amplification ratio of peak acceleration in the supporting ground of the pagodas ranges from 1.45 to 1.74, it can be shown that the two pagodas are stable against 2400-year return period earthquake level, and have excellent seismic performance. 相似文献
18.
Two correctly-scaled model cantilever retaining walls of different stiffnesses were tested under dynamic loading conditions in a centrifuge. A medium-dense fine sand was retained with a range of backfill slopes. For the centrifuge model, an earthquake-generating mechanism was designed to produce seismic shaking equivalent to that generated at ground surface in the epicentral area of an earthquake of approximate magnitude 5–5. The response of the model retaining walls to the input dynamic motion was measured by strain gauges, pressure transducers and accelerometers. From the measurements plots were constructed of moment, shear, pressure and displacement over the height of the walls as a function of time. The results are compared with calculations based on the quasi-static Mononobe-Okabe theory. Although the calculated resultant force is in reasonable agreement with the experiments, the moments can be substantially different. Residual values of all parameters at the end of shaking are considerably greater than the initial static values. It is recommended that dynamic behaviour be incorporated in the earthquake design of retaining walls. 相似文献
19.
附加或不附加粘滞阻尼墙的RC框架试验与分析 总被引：1，自引：0，他引：1
本文阐述了附加或不附加粘滞阻尼墙的2个相同的RC框架模型振动台试验和理论分析的情况.这2个钢筋混凝土框架模型为3层1跨两开间,几何相似关系大致为1：2.将阻尼墙附加到一个RC框架模型当中,先后对附加或不附加阻尼墙的2个相同的RC框架模型进行振动台试验.试验结果表明,阻尼墙有效减小了框架模型的地震反应.对耗能框架模型和普通框架模型进行了弹性和弹塑性时程分析,计算结果和试验结果吻合良好.改变阻尼墙的参数进行分析,结果表明选取合适的阻尼墙参数,才能达到最好的耗能减振效果;适当减小层间位移较小处的阻尼墙参数,对减振效果影响很小而又能节省投资. 相似文献
20.
The present study aims to obtain p-y curves(Winkler spring properties for lateral pile-soil interaction) for liquefied soil from 12 comprehensive centrifuge test cases where pile groups were embedded in liquefiable soil. The p-y curve for fully liquefied soil is back-calculated from the dynamic centrifuge test data using a numerical procedure from the recorded soil response and strain records from the instrumented pile. The p-y curves were obtained for two ground conditions:(a) lateral spreading of liquefied soil, and(b) liquefied soil in level ground. These ground conditions are simulated in the model by having collapsing and non-collapsing intermittent boundaries, which are modelled as quay walls. The p-y curves back-calculated from the centrifuge tests are compared with representative reduced API p-y curves for liquefied soils(known as p-multiplier). The response of p-y curves at full liquefaction is presented and critical observations of lateral pile-soil interaction are discussed. Based on the results of these model tests, guidance for the construction of p-y curves for use in engineering practice is also provided. 相似文献