首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Through the use of 2-D and 3-D seismic data, several gas hydrate prospects were identified in the Ulleung Basin, East Sea of Korea and thirteen drill sites were established and logging-while-drilling (LWD) data were acquired from each site in 2010. Sites UBGH2–6 and UBGH2–10 were selected to test a series of high amplitude seismic reflections, possibly from sand reservoirs. LWD logs from the UBGH2–6 well indicate that there are three significant sand reservoirs with varying thickness. Two upper sand reservoirs are water saturated and the lower thinly bedded sand reservoir contains gas hydrate with an average saturation of 13%, as estimated from the P-wave velocity. The well logs at the UBGH2–6 well clearly demonstrated the effect of scale-dependency on gas hydrate saturation estimates. Gas hydrate saturations estimated from the high resolution LWD acquired ring resistivity (vertical resolution of about 5–8 cm) reaches about 90% with an average saturation of 28%, whereas gas hydrate saturations estimated from the low resolution A40L resistivity (vertical resolution of about 120 cm) reaches about 25% with an average saturation of 11%. However, in the UBGH2–10 well, gas hydrate occupies a 5-m thick sand reservoir near 135 mbsf with a maximum saturation of about 60%. In the UBGH2–10 well, the average and a maximum saturation estimated from various well logging tools are comparable, because the bed thickness is larger than the vertical resolution of the various logging tools. High resolution wireline log data further document the role of scale-dependency on gas hydrate calculations.  相似文献   

2.
Mass-transport-deposits (MTDs) and hemipelagic mud interbedded with sandy turbidites are the main sedimentary facies in the Ulleung Basin, East Sea, offshore Korea. The MTDs show similar seismic reflection characteristics to gas-hydrate-bearing sediments such as regional seismic blanking (absence of internal reflectivity) and a polarity reversed base-reflection identical to the bottom-simulating reflector (BSR). Drilling in 2007 in the Ulleung Basin recovered sediments within the MTDs that exhibit elevated electrical resistivity and P-wave velocity, similar to gas hydrate-bearing sediments. In contrast, hemipelagic mud intercalated with sandy turbidites has much higher porosity and correspondingly lower electrical resistivity and P-wave velocity.At drill-site UBGH1-4 the bottom half of one prominent MTD unit shows two bands of parallel fractures on the resistivity log-images indicating a common dip-azimuth direction of about ∼230° (strike of ∼140°). This strike-direction is perpendicular to the seismically defined flow-path of the MTD to the north-east. At Site UBGH1-14, the log-data suggest two zones with preferred fracture orientations (top: ∼250°, bottom: ∼130°), indicating flow-directions to the north-east for the top zone, and north-west for the bottom zone. The fracture patterns may indicate post-depositional sedimentation that gave rise to a preferred fracturing possibly linked to dewatering pathways. Alternatively, fractures may be related to the formation of pressure-ridges common within MTD units.For the interval of observed MTD units, the resistivity and P-wave velocity log-data yield gas hydrate concentrations up to ∼10% at Site UBGH1-4 and ∼25% at Site UBGH1-14 calculated using traditional isotropic theories such as Archie's law or effective medium modeling. However, accounting for anisotropic effects in the calculation to honor observed fracture patterns, the gas hydrate concentration is overall reduced to less than 5%. In contrast, gas hydrate was recovered at Site UBGH1-4 near the base of gas hydrate stability zone (GHSZ). Log-data predict gas hydrate concentrations of 10–15% over an interval of 25 m above the base of GHSZ. The sediments of this interval are comprised of the hemipelagic mud and interbedded thin sandy turbidites, which did contain pore-filling gas hydrate as identified from pore-water freshening and core infra-red imaging. Seismically, this unit reveals a coherent parallel bedding character but has overall faint reflection amplitude. This gas-hydrate-bearing interval can be best mapped using a combination of regular seismic amplitude and seismic attributes such as Shale indicator, Parallel-bedding indicator, and Thin-bed indicator.  相似文献   

3.
Seismic coherency measures, such as similarity and dip of maximum similarity, were used to characterize mass transport deposits (MTDs) in the Ulleung Basin, East Sea, offshore Korea. Using 2-D and 3-D seismic data several slope failure masses have been identified near drill site UBGH1-4. The MTDs have a distinct seismic character and exhibit physical properties similar to gas hydrate bearing sediment: elevated electrical resistivity and P-wave velocity. Sediments recovered from within the MTDs show a reworked nature with chaotic assemblage of mud-clasts. Additionally, the reflection at the base of MTDs is polarity reversed relative to the seafloor, similarly to the bottom-simulating reflector commonly used to infer the presence of gas hydrates. The MTDs further show regional seismic blanking (absence of internal reflectivity), which is yet another signature often attributed to gas hydrate bearing sediments. At the drill site UBGH1-4, no gas hydrate was recovered in sediment-cores from inside a prominent MTD unit. Instead, pore-filling gas hydrate was recovered only within thin turbidite sand layers near the base of the gas hydrate stability zone. With the analysis of seismic attributes, the seismic character of the prominent MTD (Unit 3) was investigated. The base of the MTD unit exhibits deep grooves interpreted as gliding tracks from either outrunner blocks or large clasts that were dragged along the paleo-seafloor. Similar seismic features were identified on the seafloor although the length of the gliding tracks on the seafloor is much shorter (a few hundred meters to ∼1 km), compared to over 10 km long tracks at the base of the MTD. The seismic coherency attributes allowed to estimate the volume of the failed sediment as well as the direction of the flow of sediment. Tracking the MTD and extrapolating its spatial extent from the 3-D seismic volume to adjacent 2-D seismic profiles, a possible source region of this mass failure was defined ∼50 km upslope of Site UBGH1-4.  相似文献   

4.
A mound related to a cold vent in a columnar seismic blanking zone (CSBZ) was formed around site UBGH1-10 in the central Ulleung Basin (2077 m water depth), East Sea, Korea. The mound is 300–400 m wide and 2–3 m high according to multi-beam bathymetry, 2–7 kHz sub-bottom profiler data, and multi-channel reflection seismic data. Seafloor topography and characteristics were investigated using a remotely operated vehicle (ROV) around site UBGH1-10, which is located near the northern part of the mound. The origin of the mound was investigated through lithology, mineralogy, hydrate occurrence, and sedimentary features using dive cores, piston cores, and a deep-drilling core. The CSBZ extends to ∼265 ms two-way traveltime (TWT) below the seafloor within a mass-transport deposit (MTD) unit. Gas hydrate was entirely contained 6–141 m below the seafloor (mbsf) within hemipelagic deposits intercalated with a fine-grained turbidite (HTD) unit, characteristically associated with high resistivity values at site UBGH1-10. The hydrate is commonly characterized by veins, nodules, and massive types, and is found within muddy sediments as a fracture-filling type. Methane has been produced by microbial reduction of CO2, as indicated by C1/C2+, δ13CCH4, and δD4CH analyses. The bowl-shaped hydrate cap revealed at 20–45 ms TWT below the seafloor has very high resistivity and high salinity, suggesting rapid and recent gas hydrate formation. The origin of the sediment mound is interpreted as a topographic high formed by the expansion associated with the formation of the gas hydrate cap above the CSBZ. The lower sedimentation rate of the mound sediments may be due to local enhancement of bottom currents by topographic effects. In addition, no evidence of gas bubbles, chemosynthetic communities, or bacterial mats was observed in the mound, suggesting an inactive cold vent.  相似文献   

5.
The Gas Hydrate Research and Development Organization (GHDO) of Korea successfully accomplished both coring (hydraulic piston and pressure coring) and logging (logging-while-drilling, LWD, and wireline logging) to investigate the presence of gas hydrate during the first deep drilling expedition in the Ulleung Basin, East Sea of Korea (referred to as UBGH1) in 2007. The LWD data from two sites (UBGH1-9, UBGH1-10) showed elevated electrical resistivity (>80 Ω-m) and P-wave velocity (>2000 m/s) values indicating the presence of gas hydrate. During the coring period, the richest gas hydrate accumulation was discovered at these intervals. Based on log data, the occurrence of gas hydrate is primarily controlled by the presence of fractures. The gas hydrate saturation calculated using Archie’s relation shows greater than 60% (as high as ∼90%) of the pore space, although Archie’s equation typically overestimates gas hydrate saturation in near-vertical fractures. The saturation of gas hydrate is also estimated using the modified Biot-Gassmann theory (BGTL) by Lee and Collett (2006). The saturation values estimated rom BGTL are much lower than those calculated from Archie’s equation. Based on log data, the hydrate-bearing sediment section is approximately 70 m (UBGH1-9) to 130 m (UBGH1-10) in thickness at these two sites. This was further directly confirmed by the recovery of gas hydrate samples and pore water freshening collected from deep drilling core during the expedition. LWD data also strongly support the interpretation of the seismic gas hydrate indicators (e.g., vent or chimney structures and bottom-simulating reflectors), which imply the probability of widespread gas hydrate presence in the Ulleung Basin.  相似文献   

6.
《Marine and Petroleum Geology》2012,29(10):1979-1985
The Gas Hydrate Research and Development Organization (GHDO) of Korea successfully accomplished both coring (hydraulic piston and pressure coring) and logging (logging-while-drilling, LWD, and wireline logging) to investigate the presence of gas hydrate during the first deep drilling expedition in the Ulleung Basin, East Sea of Korea (referred to as UBGH1) in 2007. The LWD data from two sites (UBGH1-9, UBGH1-10) showed elevated electrical resistivity (>80 Ω-m) and P-wave velocity (>2000 m/s) values indicating the presence of gas hydrate. During the coring period, the richest gas hydrate accumulation was discovered at these intervals. Based on log data, the occurrence of gas hydrate is primarily controlled by the presence of fractures. The gas hydrate saturation calculated using Archie’s relation shows greater than 60% (as high as ∼90%) of the pore space, although Archie’s equation typically overestimates gas hydrate saturation in near-vertical fractures. The saturation of gas hydrate is also estimated using the modified Biot-Gassmann theory (BGTL) by Lee and Collett (2006). The saturation values estimated rom BGTL are much lower than those calculated from Archie’s equation. Based on log data, the hydrate-bearing sediment section is approximately 70 m (UBGH1-9) to 130 m (UBGH1-10) in thickness at these two sites. This was further directly confirmed by the recovery of gas hydrate samples and pore water freshening collected from deep drilling core during the expedition. LWD data also strongly support the interpretation of the seismic gas hydrate indicators (e.g., vent or chimney structures and bottom-simulating reflectors), which imply the probability of widespread gas hydrate presence in the Ulleung Basin.  相似文献   

7.
This study presents comprehensive geotechnical data of the natural marine sediments cored from the hydrate occurrence regions during the Ulleung Basin Gas Hydrate Expedition 1 (UBGH1), East Sea, offshore Korea in 2007. Geotechnical soil index properties of the Ulleung Basin sediments, including grain size distribution, porosity, water content, Atterberg limits, specific gravity, and specific surface area, were experimentally determined. These soil index properties were correlated to geotechnical engineering parameters (e.g., shear strength and friction angle) by using well-known empirical relationships. By performing standard consolidation tests on both undisturbed specimens (as recovered from the original core liner after hydrate dissociation) and remolded specimens, stress-dependent mechanical and hydraulic properties (e.g., compressibility and hydraulic conductivity) were measured. The experimental results provide important engineering parameters, and demonstrate the effect of hydrate presence and consequential dissociation to index properties, engineering parameters, and innate sediment structures.  相似文献   

8.
During the Indian National Gas Hydrate Program (NGHP) Expedition 01, a series of well logs were acquired at several sites across the Krishna–Godavari (KG) Basin. Electrical resistivity logs were used for gas hydrate saturation estimates using Archie’s method. The measured in situ pore-water salinity, seafloor temperature and geothermal gradients were used to determine the baseline pore-water resistivity. In the absence of core data, Arp’s law was used to estimate in situ pore-water resistivity. Uncertainties in the Archie’s approach are related to the calibration of Archie coefficient (a), cementation factor (m) and saturation exponent (n) values. We also have estimated gas hydrate saturation from sonic P-wave velocity logs considering the gas hydrate in-frame effective medium rock-physics model. Uncertainties in the effective medium modeling stem from the choice of mineral assemblage used in the model. In both methods we assume that gas hydrate forms in sediment pore space. Combined observations from these analyses show that gas hydrate saturations are relatively low (<5% of the pore space) at the sites of the KG Basin. However, several intervals of increased saturations were observed e.g. at Site NGHP-01-03 (Sh = 15–20%, in two zones between 168 and 198 mbsf), Site NGHP-01-05 (Sh = 35–38% in two discrete zone between 70 and 90 mbsf), and Site NGHP-01-07 shows the gas hydrate saturation more than 25% in two zones between 75 and 155 mbsf. A total of 10 drill sites and associated log data, regional occurrences of bottom-simulating reflectors from 2D and 3D seismic data, and thermal modeling of the gas hydrate stability zone, were used to estimate the total amount of gas hydrate within the KG Basin. Average gas hydrate saturations for the entire gas hydrate stability zone (seafloor to base of gas hydrate stability), sediment porosities, and statistically derived extreme values for these parameters were defined from the logs. The total area considered based on the BSR seismic data covers ∼720 km2. Using the statistical ranges in all parameters involved in the calculation, the total amount of gas from gas hydrate in the KG Basin study area varies from a minimum of ∼5.7 trillion-cubic feet (TCF) to ∼32.1 TCF.  相似文献   

9.
High-quality logging-while-drilling (LWD) downhole logs were acquired in seven wells drilled during the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II in the spring of 2009. Well logs obtained in one of the wells, the Green Canyon Block 955 H well (GC955-H), indicate that a 27.4-m thick zone at the depth of 428 m below sea floor (mbsf; 1404 feet below sea floor (fbsf)) contains gas hydrate within sand with average gas hydrate saturations estimated at 60% from the compressional-wave (P-wave) velocity and 65% (locally more than 80%) from resistivity logs if the gas hydrate is assumed to be uniformly distributed in this mostly sand-rich section. Similar analysis, however, of log data from a shallow clay-rich interval between 183 and 366 mbsf (600 and 1200 fbsf) yielded average gas hydrate saturations of about 20% from the resistivity log (locally 50−60%) and negligible amounts of gas hydrate from the P-wave velocity logs. Differences in saturations estimated between resistivity and P-wave velocities within the upper clay-rich interval are caused by the nature of the gas hydrate occurrences. In the case of the shallow clay-rich interval, gas hydrate fills vertical (or high angle) fractures in rather than filling pore space in sands. In this study, isotropic and anisotropic resistivity and velocity models are used to analyze the occurrence of gas hydrate within both the clay-rich and sand dominated gas-hydrate-bearing reservoirs in the GC955-H well.  相似文献   

10.
In 2006, the U.S. Geological Survey (USGS) completed detailed analysis and interpretation of available 2-D and 3-D seismic data and proposed a viable method for identifying sub-permafrost gas hydrate prospects within the gas hydrate stability zone in the Milne Point area of northern Alaska. To validate the predictions of the USGS and to acquire critical reservoir data needed to develop a long-term production testing program, a well was drilled at the Mount Elbert prospect in February, 2007. Numerous well log data and cores were acquired to estimate in-situ gas hydrate saturations and reservoir properties.Gas hydrate saturations were estimated from various well logs such as nuclear magnetic resonance (NMR), P- and S-wave velocity, and electrical resistivity logs along with pore-water salinity. Gas hydrate saturations from the NMR log agree well with those estimated from P- and S-wave velocity data. Because of the low salinity of the connate water and the low formation temperature, the resistivity of connate water is comparable to that of shale. Therefore, the effect of clay should be accounted for to accurately estimate gas hydrate saturations from the resistivity data. Two highly gas hydrate-saturated intervals are identified - an upper ∼43 ft zone with an average gas hydrate saturation of 54% and a lower ∼53 ft zone with an average gas hydrate saturation of 50%; both zones reach a maximum of about 75% saturation.  相似文献   

11.
《Marine and Petroleum Geology》2012,29(10):1768-1778
During the Indian National Gas Hydrate Program (NGHP) Expedition 01, a series of well logs were acquired at several sites across the Krishna–Godavari (KG) Basin. Electrical resistivity logs were used for gas hydrate saturation estimates using Archie’s method. The measured in situ pore-water salinity, seafloor temperature and geothermal gradients were used to determine the baseline pore-water resistivity. In the absence of core data, Arp’s law was used to estimate in situ pore-water resistivity. Uncertainties in the Archie’s approach are related to the calibration of Archie coefficient (a), cementation factor (m) and saturation exponent (n) values. We also have estimated gas hydrate saturation from sonic P-wave velocity logs considering the gas hydrate in-frame effective medium rock-physics model. Uncertainties in the effective medium modeling stem from the choice of mineral assemblage used in the model. In both methods we assume that gas hydrate forms in sediment pore space. Combined observations from these analyses show that gas hydrate saturations are relatively low (<5% of the pore space) at the sites of the KG Basin. However, several intervals of increased saturations were observed e.g. at Site NGHP-01-03 (Sh = 15–20%, in two zones between 168 and 198 mbsf), Site NGHP-01-05 (Sh = 35–38% in two discrete zone between 70 and 90 mbsf), and Site NGHP-01-07 shows the gas hydrate saturation more than 25% in two zones between 75 and 155 mbsf. A total of 10 drill sites and associated log data, regional occurrences of bottom-simulating reflectors from 2D and 3D seismic data, and thermal modeling of the gas hydrate stability zone, were used to estimate the total amount of gas hydrate within the KG Basin. Average gas hydrate saturations for the entire gas hydrate stability zone (seafloor to base of gas hydrate stability), sediment porosities, and statistically derived extreme values for these parameters were defined from the logs. The total area considered based on the BSR seismic data covers ∼720 km2. Using the statistical ranges in all parameters involved in the calculation, the total amount of gas from gas hydrate in the KG Basin study area varies from a minimum of ∼5.7 trillion-cubic feet (TCF) to ∼32.1 TCF.  相似文献   

12.
珠江口盆地神狐海域是天然气水合物钻探和试验开采的重点区域,大量钻探取心、测井与地震等综合分析表明不同站位水合物的饱和度、厚度与气源条件存在差异。本文利用天然气水合物调查及深水油气勘探所采集的测井和地震资料建立地质模型,利用PetroMod软件模拟地层的温度场、有机质成熟度、烃源岩生烃量、流体运移路径以及不同烃源岩影响下的水合物饱和度,结果表明:生物成因气分布在海底以下1500 m范围内的有机质未成熟地层,而热成因气分布在深度超过2300 m的成熟、过成熟地层。水合物稳定带内生烃量难以形成水合物,形成水合物气源主要来自于稳定带下方向上运移的生物与热成因气。模拟结果与测井结果对比分析表明,稳定带下部生物成因气能形成的水合物饱和度约为10%,在峡谷脊部的局部区域饱和度较高;相对高饱和度(>40%)水合物形成与文昌组、恩平组的热成因气沿断裂、气烟囱等流体运移通道幕式释放密切相关,W19井形成较高饱和度水合物的甲烷气体中热成因气占比达80%,W17井热成因气占比为73%,而SH2井主要以生物成因为主,因此,不同站位甲烷气体来源占比不同。  相似文献   

13.
Abstract

Geophysical evidence indicating the presence of gas hydrate has been found in the Ulleung Basin, which lies off the east coast of the Korean Peninsula; however, hydrate distribution in the basin is not well understood. Logging-while-drilling data for 13 sites in the Ulleung Basin, East Sea, were obtained to investigate the distribution pattern of gas hydrate. Most of the sites yielded log data indicating the presence of gas hydrate. Prominent fractures (both resistive and conductive fractures) were clearly identified on the resistivity borehole images, particularly at seismic chimney sites. Resistive fractures, which contain large amounts of gas hydrate, are prominent in the seismic chimney sites. The strike and dip of each fracture was calculated and displayed on a stereographic plot and rosette diagram. From the fracture orientations on the stereographic plots, the maximum horizontal stress is NW–SE, reflecting the regional stress regime around the Ulleung Basin, although the fracture orientations are broadly distributed, indicating that the fracture pattern is not well-ordered on the rosette diagram. The fracture dips are between 36.46° and 63.66°; the range of dip azimuths is 0.94°–359°, and exhibit little change with depth. The dip azimuths are generally westerly to southwesterly.  相似文献   

14.
《Marine and Petroleum Geology》2012,29(10):1953-1966
The presence of gas hydrate in the Ulleung Basin, East Sea (Japan Sea), inferred by various seismic indicators, including the widespread bottom-simulating reflector (BSR), has been confirmed by coring and drilling. We applied the standard AVO technique to the BSRs in turbidite/hemipelagic sediments crosscutting the dipping beds and those in debris-flow deposits to qualitatively assess the gas hydrate and gas concentrations. These BSRs are not likely to be affected by thin-bed tuning which can significantly alter the AVO response of the BSR. The BSRs crosscutting the dipping beds in turbidite/hemipelagic sediments are of low-seismic amplitude and characterized by a small positive gradient, indicating a decrease in Poisson’s ratio in the gas-hydrate stability zone (GHSZ), which, in turn, suggests the presence of gas hydrate. The BSRs in debris-flow deposits are characterized by a negative gradient, indicating decreased Poisson’s ratio below the GHSZ, which is likely due to a few percent or greater gas saturations. The increase in the steepness of the AVO gradient and the magnitude of the intercept of the BSRs in debris-flow deposits with increasing seismic amplitude of the BSRs is probably due to an increase in gas saturations, as predicted by AVO model studies based on rock physics. The reflection strength of the BSRs in debris-flow deposits, therefore, can be a qualitative measure of gas saturations below the GHSZ.  相似文献   

15.
The presence of gas hydrate in the Ulleung Basin, East Sea (Japan Sea), inferred by various seismic indicators, including the widespread bottom-simulating reflector (BSR), has been confirmed by coring and drilling. We applied the standard AVO technique to the BSRs in turbidite/hemipelagic sediments crosscutting the dipping beds and those in debris-flow deposits to qualitatively assess the gas hydrate and gas concentrations. These BSRs are not likely to be affected by thin-bed tuning which can significantly alter the AVO response of the BSR. The BSRs crosscutting the dipping beds in turbidite/hemipelagic sediments are of low-seismic amplitude and characterized by a small positive gradient, indicating a decrease in Poisson’s ratio in the gas-hydrate stability zone (GHSZ), which, in turn, suggests the presence of gas hydrate. The BSRs in debris-flow deposits are characterized by a negative gradient, indicating decreased Poisson’s ratio below the GHSZ, which is likely due to a few percent or greater gas saturations. The increase in the steepness of the AVO gradient and the magnitude of the intercept of the BSRs in debris-flow deposits with increasing seismic amplitude of the BSRs is probably due to an increase in gas saturations, as predicted by AVO model studies based on rock physics. The reflection strength of the BSRs in debris-flow deposits, therefore, can be a qualitative measure of gas saturations below the GHSZ.  相似文献   

16.
Through the use of 3-D seismic amplitude mapping, several gas hydrate prospects were identified in the Alaminos Canyon (AC) area of the Gulf of Mexico. Two locations were drilled as part of the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II (JIP Leg II) in May of 2009 and a comprehensive set of logging-while-drilling (LWD) logs were acquired at each well site. LWD logs indicated that resistivity in the range of ∼2 ohm-m and P-wave velocity in the range of ∼1.9 km/s were measured in the target sand interval between 515 and 645 feet below sea floor. These values were slightly elevated relative to those measured in the sediment above and below the target sand. However, the initial well log analysis was inconclusive regarding the presence of gas hydrate in the logged sand interval, mainly because large washouts caused by drilling in the target interval degraded confidence in the well log measurements. To assess gas hydrate saturations in the sedimentary section drilled in the Alaminos Canyon 21 B (AC21-B) well, a method of compensating for the effect of washouts on the resistivity and acoustic velocities was developed. The proposed method models the washed-out portion of the borehole as a vertical layer filled with sea water (drilling fluid) and the apparent anisotropic resistivity and velocities caused by a vertical layer are used to correct the measured log values. By incorporating the conventional marine seismic data into the well log analysis, the average gas hydrate saturation in the target sand section in the AC21-B well can be constrained to the range of 8–28%, with 20% being our best estimate.  相似文献   

17.
Gas hydrate was discovered in the Krishna–Godavari (KG) Basin during the India National Gas Hydrate Program (NGHP) Expedition 1 at Site NGHP-01-10 within a fractured clay-dominated sedimentary system. Logging-while-drilling (LWD), coring, and wire-line logging confirmed gas hydrate dominantly in fractures at four borehole sites spanning a 500 m transect. Three-dimensional (3D) seismic data were subsequently used to image the fractured system and explain the occurrence of gas hydrate associated with the fractures. A system of two fault-sets was identified, part of a typical passive margin tectonic setting. The LWD-derived fracture network at Hole NGHP-01-10A is to some extent seen in the seismic data and was mapped using seismic coherency attributes. The fractured system around Site NGHP-01-10 extends over a triangular-shaped area of ∼2.5 km2 defined using seismic attributes of the seafloor reflection, as well as “seismic sweetness” at the base of the gas hydrate occurrence zone. The triangular shaped area is also showing a polygonal (nearly hexagonal) fault pattern, distinct from other more rectangular fault patterns observed in the study area. The occurrence of gas hydrate at Site NGHP-01-10 is the result of a specific combination of tectonic fault orientations and the abundance of free gas migration from a deeper gas source. The triangular-shaped area of enriched gas hydrate occurrence is bound by two faults acting as migration conduits. Additionally, the fault-associated sediment deformation provides a possible migration pathway for the free gas from the deeper gas source into the gas hydrate stability zone. It is proposed that there are additional locations in the KG Basin with possible gas hydrate accumulation of similar tectonic conditions, and one such location was identified from the 3D seismic data ˜6 km NW of Site NGHP-01-10.  相似文献   

18.
Drilling at the site UBGH1-9, offshore Korea in 2007, revealed varied gas-hydrate saturation with depth and a wide variety of core litholgies, demonstrating how the variations in the lithology are linked with those in gas-hydrate saturation and morphology. Discrete excursions to low chlorinity values from in situ background chlorinity level occur between 63 and 151 mbsf. In this occurrence zone, gas-hydrate saturations estimated from the low chlorinity anomalies range up to 63.5% of pore volume with an average of 9.9% and do not show a clear depth-dependent trend. Sedimentary facies analysis based on grain-size distribution and sedimentary structures revealed nine sediment facies which mainly represent hemipelagic muds and fine- to medium-grained turbidites. According to the sedimentary facies distribution, the core sediments are divided into three facies associations (FA): FA I (0–98 mbsf) consisting mainly of alternating thin- to medium-bedded hemipelagic mud and turbidite sand or mud beds, FA II (98–126 mbsf) dominated by medium- to very thick-bedded turbidite sand or sandy debris flow beds, and FA III (126–178 mbsf) characterized by thick hemipelagic mud without intervening discrete turbidite sand layers. Thermal anomalies from IR scan, mousse-like and soupy structures on split-core surfaces, non-destructive measurements of pressure cores, and comparison of gas-hydrate saturations with sand contents of corresponding pore-water squeeze cakes, collectively suggest that the gas hydrate at the site UBGH1-9 generally occurs in two different types: “pore-filling” type preferentially associated with thin- to medium-turbidite sand beds in the FA I and “fracture-filling” type which occurs as hydrate veins or nodules in hemipelagic mud of the FA III. Gas-hydrate saturation in the FA II is generally anomalously low despite the dominance of turbidite sand or sandy debris flow beds, suggesting insufficient methane supply.  相似文献   

19.
Gas hydrates in the western deep-water Ulleung Basin, East Sea of Korea   总被引：1，自引：0，他引：1  
Geophysical surveys and geological studies of gas hydrates in the western deep-water Ulleung Basin of the East Sea off the east coast of Korea have been carried out by the Korea Institute of Geoscience and Mineral Resources (KIGAM) since 2000. The work included a grid of 4782 km of 2D multi-channel seismic reflection lines and 11 piston cores 5–8 m long. In the piston cores, cracks generally parallel to bedding suggest significant in-situ gas. The cores showed high amounts of total organic carbon (TOC), and from the southern study area showed high residual hydrocarbon gas concentrations. The lack of higher hydrocarbons and the carbon isotope ratios indicate that the methane is primarily biogenic. The seismic data show areas of bottom-simulating reflectors (BSRs) that are associated with gas hydrates and underlying free gas. An important observation is the numerous seismic blanking zones up to 2 km across that probably reflect widespread fluid and gas venting and that are inferred to contain substantial gas hydrate. Some of the important results are: (1) BSRs are widespread, although most have low amplitudes; (2) increased P-wave velocities above some BSRs suggest distributed low to moderate concentration gas hydrate whereas a velocity decrease below the BSR suggests free gas; (3) the blanking zones are often associated with upbowing of sedimentary bedding reflectors in time sections that has been interpreted at least in part due to velocity pull-up produced by high-velocity gas hydrate. High gas hydrate concentrations are also inferred in several examples where high interval velocities are resolved within the blanking zones. Recently, gas hydrate recoveries by the piston coring and deep-drilling in 2007 support the interpretation of substantial gas hydrate in many of these structures.  相似文献   

20.
Fractures and borehole breakouts from image data acquired from Logging-While-Drilling (LWD) were identified and analyzed using GMI Imager software. Conductive (e.g., dark-colored images) and resistive fractures (e.g., light-colored images) were identified on the images. Breakouts occurring along the borehole wall in the direction of the minimum horizontal stress were also investigated. For fracture analysis, we investigated dip and direction of fractures on the resistivity images acquired from two sites in the Ulleung Basin, East Sea. Dip angles at two sites are 42° and 62.5° on average, respectively. Dip direction shows preferred orientation northerly. From fracture analysis, the maximum horizontal stress direction may be the NW-SE direction. This pattern likely reflects regional stress regime of this area. We also analyzed borehole breakouts on the LWD image data (borehole radius and density data) acquired from Site U1378, IODP Exp. 334 off Costa Rica. We estimated present-day in situ stress orientation from borehole breakouts. Breakout orientation of slope sediments at Site U1378 indicates that maximum horizontal principal stress direction is oriented northwest-southeast. This direction is probably related to plate motion in this area. This study presents preliminary results in order to interpret not only stress history of the Ulleung Basin but also in situ stress state of continental slope off Costa Rica in near future.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号