共查询到20条相似文献，搜索用时 625 毫秒
1.
在分析特殊型地震动如近场脉冲型地震动或远场类谐和地震动时,研究和设计人员更关注于地震动的时域特性.鉴于目前尚不具有一种成熟的用于分析地震动时域特性的方法,在研究中通常采用肉眼辨别地震动.但在肉眼辨别的过程中并没有定量的指标描述地震动的特性,因此这种方法容易引入人为的主观性误差.地震动的时域特性主要指地震动的振动周期和强度随时间的变化情况.如有一种定量描述这种变化的方法便能消除肉眼辨别中引入的主观性误差.为解决该问题,本文提出了一种简便、有效的分析地震动速度时程时域特性的速度零点法ZVPM(Zero Velocity Point Method).采用这种方法可以定量地分析地震动速度时程的振动周期和强弱程度随时间的变化情况,并可以通过定义的幅值参数、周期参数和相位参数获取等效的地震动速度时程.鉴于脉冲型地震动对结构具有特殊的破坏作用,本文采用速度零点法分析了24条典型的强脉冲型地震动,并基于速度零点法提出了一种简便的脉冲周期计算方法.为便于工程设计人员快速地获取本文所选脉冲型地震动的等效速度脉冲,文中给出了每一条地震动等效速度脉冲的数学表达式. 相似文献
2.
Coulomb damping can be utilized effectively to reduce the dynamic response of structures subjected to seismic ground motions. To activate this damping, some parts of a vibrating structure are allowed to slide at rough interfaces. The dynamic response of structures provided with sliding interfaces at the base, between a floor slab and frame and in the cross bracings of a frame has been examined recently. In this paper, a simple slab sliding system provided with a spring to introduce a recovery mechanism and to reduce the sliding displacement requirement for low frequency structures has been examined. The equations of motion for this system are developed. An approach is presented to solve these coupled equations for earthquake induced ground motions. Structures with varying frequency and friction characterisics are considered and the numerical results are presented in response spectrum form. It is observed that, in low frequency structures, provision of a rather weak spring can reduce the sliding displacement requirements without significantly increasing the forces in the supporting frame and the acceleration input to supported secondary systems. 相似文献
3.
近断层地震动中长周期、短持时和高能量的加速度脉冲将对高层摩擦摆基础隔震结构的减震性能产生不利影响,考虑土-结构相互作用（SSI效应）后的隔震结构将产生动力耦合效应,可能进一步放大隔震结构地震响应。为此,通过一幢框架-核心筒高层摩擦摆基础隔震结构的非线性地震响应分析,考察近断层脉冲型地震动作用下框架-核心筒摩擦摆基础隔震结构的层间位移角、楼层加速度和隔震层变形等响应规律,揭示隔震体系的损伤机理。基于集总参数SR （sway-rocking）模型,分析不同场地类别与不同地震动类型对隔震体系动力响应影响规律。结果表明:高层摩擦摆基础隔震结构在近断层脉冲型地震动作用下的减震效果相比普通地震动减震效果变差,楼层剪力、层间位移角和隔震层变形等超越普通地震动作用下的1.5倍;对于Ⅲ和Ⅳ类场地类别,考虑SSI效应使隔震结构的地震响应进一步放大,弹塑性层间位移角随着土质变软增大尤为明显。 相似文献
4.
5.
Christopher Bode Reinhold Hirschauer Stavros A. Savidis 《Soil Dynamics and Earthquake Engineering》2002,22(4)
A time-domain formulation is proposed for the transient response analysis of general, three-dimensional structures resting on a homogeneous, elastic halfspace subjected to either external loads or seismic motions. The formulation consists of two parts: (a) the time domain formulation of the soil behaviour and (b) the coupling of the corresponding soil algorithms to the Finite Element Code ANSYS. As far as the structure is concerned, this coupling opens the way for the analysis of non-linear soil–structure interaction. The approach is based on halfspace Green's functions for displacements elicited by Heaviside time-dependent surface point loads. Hence, the spatial discretisation can be confined to the contact area between the foundation and the soil, i.e. no auxiliary grid beyond the foundation as for conventional boundary element formulations is required. The method is applied to analyse the dynamic response of a railway track due to a moving wheel set by demonstrating the influence of ‘through-the-soil coupling’. 相似文献
6.
7.
Wave passage and differential motions at multiple supports of long structures result in excessive demands in the near field of strong earthquakes. These demands are caused mainly by pseudo-static deformations imposed by differential ground motions. As would be expected, replacing continuous bridge girders with multiple short segments, interconnected by structural joints reduces the large pseudo-static forces in the piers. In this paper, these reductions are quantified for a three-span simply supported bridge. It is shown that the shear forces in the joint keys, as well as the drifts of piers, for out-of-plane response are reduced in the high frequency band in the structural system that is made flexible by placement of joints over the piers. 相似文献
8.
The boundary element method has been successfully applied in the past to the analysis of hydrodynamic forces in two- and three-dimensional finite water reservoirs subjected to seismic ground motions. In extending the method to an infinite reservoir, the loss of energy due to pressure waves moving away towards infinity must be taken into account. In addition, for both finite and infinite reservoirs, energy is lost owing to partial absorption of the waves incident on a flexible bottom consisting of alluvial deposits. This paper presents the results of more recent research on the application of the boundary element method to the analysis of 2D reservoir vibration. Two different formulations are used: a constant boundary element formulation and a linear boundary element formulation. Special boundary conditions to treat infinite radiation and foundation damping have been incorporated in both formulations. Numerical results have been obtained for each of the two alternative formulations and compared against each other as well as with classical solutions and results obtained by other researchers. 相似文献
9.
In this paper the efficiency of various dissipative mechanisms to protect structures from pulse‐type and near‐source ground motions is examined. Physically realizable cycloidal pulses are introduced, and their resemblance to recorded near‐source ground motions is illustrated. The study uncovers the coherent component of some near‐source acceleration records, and the shaking potential of these records is examined. It is found that the response of structures with relatively low isolation periods is substantially affected by the high‐frequency fluctuations that override the long duration pulse. Therefore, the concept of seismic isolation is beneficial even for motions that contain a long duration pulse which generates most of the unusually large recorded displacements and velocities. Dissipation forces of the plastic (friction) type are very efficient in reducing displacement demands although occasionally they are responsible for substantial permanent displacements. It is found that the benefits by hysteretic dissipation are nearly indifferent to the level of the yield displacement of the hysteretic mechanism and that they depend primarily on the level of the plastic (friction) force. The study concludes that a combination of relatively low friction and viscous forces is attractive since base displacements are substantially reduced without appreciably increasing base shears and superstructure accelerations. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
10.
地震动差动作用下大跨度空间网壳结构的反应分析 总被引：1，自引：0，他引：1
选取100m跨度的双层柱面网壳结构为研究对象,采用时程分析法,分别进行了结构在单向和三向地震行波输入作用下的反应分析,并针对多种视波速情况进行了研究,考查了地震动不同输入情况下结构杆件内力的分布特点,对其进行了对比分析,为大跨网壳结构的抗震设计提供了理论依据。研究表明,考虑行波效应会使结构部分构件内力有一定程度的提高,多维地震作用比单维地震作用下结构的杆件内力大。由此得出结论：对于大跨度空间网壳结构,应该进行多维非一致输入下的地震反应分析;为保证抗震安全,应对可能出现的地面视波速进行全面分析。 相似文献
11.
实际记录到的真实地震动在工程结构的抗震研究、分析和设计中往往作为一种施加到结构上使结构振动，直至破坏的地震荷载．如何合理选择真实的地震动记录作为研究结构地震反应的输入，一直是国内外抗震研究和设计中引人关注的重要问题．本文首先提出了最不利设计地震动的概念；然后在收集到的国内外5000余条被认为有重要意义的地震动记录基础上，利用综合估计地震动潜在破坏势的方法，对４种场地类型分别给出了长周期、短周期和中周期结构的国内外最不利设计地震动；最后通过几类不同结构的地震反应分析，初步验证了本文所确定的最不利设计地震动的可靠性和合理性． 相似文献
12.
How to select the adequate real strong earthquake ground motion for seismic analysis and design of trucures is an essential problem in earthquake engineering research and practice.In the paper the concept of the severest design ground motion is proposed and a method is developed for comparing the severity of the recorded strong ground motions.By using this method the severest earthquake ground motions are selected out as seismic inputs to the structures to be designed from a database that consists of more than five thousand significant strong ground moton records collected over the world.The selected severest ground motions are very likely to be able to drive the structures to their critical response and thereby result in the highest damage potential.It is noted that for different structures with diffferent predominant natural periods and at different sites where structures are located the severest design ground motions are usually different.Finally.two examples are illustrated to demonstrate the rationality of the concept and the reliability of the selected design motion. 相似文献
13.
Aspasia Zerva 《地震工程与结构动力学》1990,19(6):819-832
The response of continuous two- and three-span beams of various lengths subjected to spatially varying seismic ground motions is evaluated. Stochastic representations of the seismic ground motions are used as input at the supports of the structures, and sensitivity analyses of the response with respect to the degree of correlation between the support motions are performed. The validity of the commonly used assumption of equal support motion is examined. Square-roots of mean-square values of total displacements, bending moments and shear forces are outputs of the analyses. The results indicate that fully correlated motions may produce higher or lower response than partially correlated motions, depending on the dynamic characteristics of the structure, the response quantity (bending moment or shear force) that is evaluated, the position along the axis of the beam where the response quantity is evaluated, the separation between the natural frequencies of the structure and the dominant frequencies of the input motions, and on the degree of partial correlation between the support motions. 相似文献
14.
Erdal afak 《Soil Dynamics and Earthquake Engineering》2006,26(1):65-70
Foundation impedance functions provide a simple means to account for soil–structure interaction (SSI) when studying seismic response of structures. Impedance functions represent the dynamic stiffness of the soil media surrounding the foundation. The fact that impedance functions are frequency dependent makes it difficult to incorporate SSI in standard time-history analysis software. This paper introduces a simple method to convert frequency-dependent impedance functions into time-domain filters. The method is based on the least-squares approximation of impedance functions by ratios of two complex polynomials. Such ratios are equivalent, in the time-domain, to discrete-time recursive filters, which are simple finite-difference equations giving the relationship between foundation forces and displacements. These filters can easily be incorporated into standard time-history analysis programs. Three examples are presented to show the applications of the method. 相似文献
15.
It is well known that the generation of excess pore water pressure and/or liquefaction in foundation soils during an earthquake often cause structural failures.This paper describes the behavior of a small-scale braced wall embedded in saturated liquefiable sand under dynamic condition.Shake table tests are performed in the laboratory on embedded retaining walls with single bracing.The tests are conducted for different excavation depths and base motions.The influences of the peak magnitude of the ground motions and the excavation depth on the axial forces in the bracing,the lateral displacement and the bending moments in the braced walls are studied.The shake table tests are simulated numerically using FLAC 2D and the results are compared with the corresponding experimental results.The pore water pressures developed in the soil are found to influence the behavior of the braced wall structures during a dynamic event.It is found that the excess pore water pressure development in the soil below the excavation is higher compared to the soil beside the walls.Thus,the soil below the excavation level is more susceptible to the liquefaction compared to the soil beside the walls. 相似文献
16.
17.
David M. Lee 《地震工程与结构动力学》1980,8(4):349-359
This paper examines the effectiveness of a bilinear hysteretic base isolation system in lowering the shear forces and torques generated in a structure by two-way, translatory ground motions. The study is restricted to single-storey, three-dimensional structures having asymmetries in both horizontal directions and being excited by the El Centro (May 1940) earthquake motions. It is shown that with base isolation the structural torques are drastically reduced, even if the structural eccentricity is large. This reduction in structural torque is greatest when the isolation system's centre of stiffness coincides with the structure's centre of mass. The highly dissipative action of the isolation system provides strong modal decoupling which prevents the translational motions from resonantly driving the torsional motions. The maximum base displacements, due to both translation and rotation combined are less than 11 cm, which is well within the limits of currently available isolation system components. The dynamic action of the base isolation system is outlined and currently available isolation system components described. 相似文献
18.
The objective of this paper is to describe the lessons learned and actions that have been taken related to the seismic design
of bridge structures after the Chi-Chi, Taiwan earthquake. Much variable near-fault ground motion data was collected from
the rupture of Chelungpu fault during the Chi-Chi earthquake, allowing the seismic response of bridge structures subjected
to these near-fault ground motions to be carefully examined. To study the near-fault ground motion effect on bridge seismic
design codes, a two-level seismic design of bridge structures was developed and implemented. This design code reflects the
near-fault factors in the seismic design forces. Finally, a risk assessment methodology, based on bridge vulnerability, is
also developed to assist in decisions for reducing seismic risk due to failure of bridges.
Director of Center for Research on Earthquake Engineering.
Supported by: the Science Council, Chinese Taipei, under grant no. SC 90-2211-E-002-028. 相似文献
19.
A generalized multi‐mode pushover analysis procedure was developed for estimating the maximum inelastic seismic response of symmetrical plan structures under earthquake ground excitations. Pushover analyses are conducted with story‐specific generalized force vectors in this procedure, with contributions from all effective modes. Generalized pushover analysis procedure is extended to three‐dimensional torsionally coupled systems in the presented study. Generalized force distributions are expressed as the combination of modal forces to simulate the instantaneous force distribution acting on the system when the interstory drift at a story reaches its maximum value during seismic response. Modal contributions to the generalized force vectors are calculated by a modal scaling rule, which is based on the complete quadratic combination. Generalized forces are applied to the mass centers of each story incrementally for producing nonlinear static response. Maximum response quantities are obtained when the individual frames attain their own target interstory drift values in each story. The developed procedure is tested on an eight‐story frame under 15 ground motions, and assessed by comparing the results obtained from nonlinear time history analysis. The method is successful in predicting the torsionally coupled inelastic response of frames responding to large interstory drift demands. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献