首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 156 毫秒
1.
The Blackfoot Reservoir region in southeastern Idaho is recognized as a potential geothermal area because of the presence of several young rhyolite domes (50,000 years old), Quaternary basalt flows, and warm springs. North- to northwest-trending high-angle normal faults of Tertiary to Holocene age appear to be the dominant structural control of spring activity. Surface spring-water temperatures average 14°C except for a group of springs west of the Reservoir Mountains which average 33°C. Chemical geothermometers applied to fifty water samples give temperatures less than 75°C except for eight springs along the Corral Creek drainage. The springs along Corral Creek have Na-K-Ca temperatures that average 354°C, a direct result of high potassium concentrations in the water. A correction for carbon dioxide applied to the Na-K-Ca geothermometer lowers the estimated temperatures of the anomalous springs to near the measured surface temperatures, and Na-K-Ca-Mg temperatures for the anomalous springs are near 100°C. Mixing model calculations suggest that hot water with a temperature of approximately 120°C may be mixing with cooler, more dilute water in the springs from the Corral Creek drainage, a temperature supported by Na-K-Ca-Mg temperatures and mineral saturation temperatures.Stability relations of low-temperature phases in the system indicate that the large concentrations of potassium in the eight anomalous springs are derived from reactions with the potassium-bearing minerals muscovite and K-feldspar. Carbon dioxide and hydrogen sulfide gases may be derived through the oxidation of organic matter accompanied by the reduction of sulfate. Concentrations of major and minor elements, and gases found in springs of the Blackfoot Reservoir region are due to water-rock reactions at temperatures less than 100°C.Based on spring geochemistry, a geothermal reservoir of 100°C up to 120°C may exist at shallow (less than 2 km) depths in the Blackfoot Reservoir region.  相似文献   

2.
The Campi Flegrei (Naples, Campanian Plain, southern Italy) geothermal system is hosted by Quaternary volcanic rocks erupted before, during and after the formation of the caldera that represents one of the major structural features in the Neapolitan area. The volcanic products rest on a Mesozoic carbonate basement, cropping out north, east and south of the area. Chemical (major, minor and trace elements) and stable isotope (C, H, O) analyses were conducted on drill-core samples recovered from geothermal wells MF-1, MF-5, SV-1 and SV-3, at depths of ˜ 1100 to 2900 m. The study was complemented by petrographic and SEM examination of thin sections. The water which feeds the system is both marine and meteoric in origin. Mineral zonation typical of a high-temperature geothermal system exists in all the geothermal wells; measured temperatures in wells are as high as ˜ 400 °C. The chemical composition of the waters suggests the existence of two reservoirs: a shallow reservoir (depth < 2000 m) fed by seawater that boiled at 320 °C and became progressively diluted by steam-heated local meteoric water during its ascent; and a deeper reservoir (depth > 2000 m) of hypersaline water. The drill-cores are mainly hydrothermally altered volcanics of trachy-latitic affinity, but some altered pelites and limestones are also present. Published Na, Mg and K concentrations of selected geothermal waters indicate that the hydrothermal fluids are in equilibrium with their host rocks, with respect to K-feldspar, albite, sericite and chlorite. The measured δ18O(SMOW) values of rocks range from +4.3 to + 16.5%. The measured δD(SMOW) values range from − 79 to − 46%. The calculated isotopic composition of the fluids at equilibrium with the samples vary from + 1 to + 8.3%. δ18O and from − 52 to + 1%. δD. The estimated isotopic composition of the waters at equilibrium with the studied samples confirmed the existence of two distinct fluid types circulating in the geothermal system. The shallower has a marine water signature, while the deeper water has a signature consistent both with magmatic and meteoric origins. In the latter case, the recharge of this aquifer likely occurs at the outcrop of the Mesozoic Limestones surrounding the Campanian Plain; after infiltration, the water percolates through evaporitic layers, becoming hypersaline and D-depleted.  相似文献   

3.
Geochemical studies on fifteen geothermal manifestations (38–70°C) from the Konkan coast geothermal province of India have been used to evaluate the reservoir temperatures. Activity studies of the minerals and the waters present in the reservoirs suggest that the thermal waters are in equilibrium with montmorillonite, kaolinite and quartz at about 100°C. Reservoir temperatures of these geothermal systems as estimated by geochemical thermometers, are 88 to 128°C, and thus too low for economic electricity production.  相似文献   

4.
The Latera field (Vulsini volcanic complex, Latium, Italy) is one of the geothermal areas of the peri-Tyrrhenian belt along which a regional, high thermal anomaly has been detected. So far nine deep wells have been drilled within the Latera caldera and four of them have been productive. The geothermal reservoir is located within the fractured carbonatic rocks of the Tuscan nappe; the overlying volcanic units, sealed by hydrothermal minerals (mainly calcite and anhydrite), act as an impervious cover.The fluid produced by the wells comes from a deep aquifer (about 1000–1500 m depth) which at present is not connected with the shallow aquifer in the volcanoclastic units. Fluid temperatures range between 200 and 230°C; in-hole temperatures as high as 343°C at 2775 m depth have been measured in dry wells.The study of the newly formed mineral assemblages from both volcanic and sedimentary units as sampled from the geothermal wells can be used to reconstruct the thermal evolution of the geothermal field. The intrusion of a syenitic melt, up to a depth of about 2000 m, dated 0.86 Ma, represents the major thermal event for the units in the area and is assumed to represent the first step in the geothermal evolution of the Latera system.The above mentioned newly formed mineral assemblages can be divided into three groups: (a) “contact-metasomatic”: calcite, anhydrite, diopsidic pyroxene, grossularitic garnet, phlogopite, wollastonite or monticellite; (b) “high-temperature hydrothermal”: calcite, anhydrite, K-feldspar, vesuvianite, melanitic garnet, tourmaline, amphibole, epidote, sulphides; (c) “low-temperature hydrothermal”: calcite, anhydrite, K-feldspar, clay minerals, sulphides. Group (a) minerals are now relics. Part of (b) and all of (c) group are still in equilibrium with the existing conditions in different parts of the geothermal system.Thermodynamic calculations on the observed mineral assemblages permitted estimates of the P, T conditions and gas fugacities.  相似文献   

5.
40Ar/39Ar step heating of single K-feldspar crystals ( 500 μg) in a furnace with a low argon blank and accurate temperature control provide constraints on the thermal history of the Salton Sea geothermal field, southern California. Estimates of 40Ar loss from detrital K-feldspars, coupled with kinetic information gleaned from laboratory degassing of 39Ar, allow possible thermal histories to be evaluated. Samples from core and cuttings of sandstones from the State 2–14, Landers #1, Dearborn Farms #1, Magmamax #2, Elmore #3 and Sinclair #3 wells have been analyzed for this purpose. No recent 40Ar* loss is recognized in any of the 17 crystals measured, even for samples currently at temperatures greater than 275°C. This observation suggests that the present temperature distributions in these wells have not been maintained for greater than 1000 years. However, aggregates ( 100 mg) of two K-feldspar samples do reveal recent 40Ar* loss from the State 2–14 well, suggesting a time scale of 1000 to 5000 years for near-peak thermal conditions. These estimates of heating duration are broadly consistent with earlier results from thermal modelling, but do not support interpretations that paleotemperatures were once hotter than present.Provenance ages span the Tertiary through Middle Proterozoic but cluster at ages of 25, 70 and 1250 Ma. These age peaks are very common K-feldspar K-Ar ages in detachment terranes of southeastern California and southwestern Arizona, both drained by the Colorado River. This coincidence supports earlier suggestions that the sands of the Salton Trough were derived mainly from the Colorado River.Unrealistically low apparent activation energies (< 20 kcal/mol) for argon transport are observed for several single crystals which yield absurdly low calculated closure temperatures (e.g., -100°C). We infer that this anomalous behaviour results from a combination of the laboratory heating schedule and the distribution of diffusion domain sizes.  相似文献   

6.
Homogenization temperatures of individual fluid inclusions from the geothermal test well sites near Los Alamos, New Mexico, systematically change as a function of depth in the cores. Inclusions in samples from depths between 1.5 and 3.0 km have re-equilibrated to thermal gradients higher than the present gradient of 50–60°C/km. The loci of maximum temperatures attained has a slope of about 70°C/km; the deepest sample has cooled to 200°C from a maximum of 230°C. The wide range of salinities (0.0 wt.% equivalent NaCl to more than 25 wt.% equivalent NaCl) observed in each sample indicates a large amount of pervasive fluid circulation had not occurred at the time of re-equilibration of these inclusions. The results are relevant to calculations for the thermal history of the test site.  相似文献   

7.
The Quaternary Takidani Granodiorite (Japan Alps) is analogous to the type of deep-seated (3–5 km deep) intrusive-hosted fracture network system that might support (supercritical) hot dry/wet rock (HDR/HWR) energy extraction. The I-type Takidani Granodiorite comprises: porphyritic granodiorite, porphyritic granite, biotite-hornblende granodiorite, hornblende-biotite granodiorite, biotite-hornblende granite and biotite granite facies; the intrusion has a reverse chemical zonation, characterized by >70 wt% SiO2 at its inferred margin and <67 wt% SiO2 at the core. Fluid inclusion evidence indicates that fractured Takidani Granodiorite at one time hosted a liquid-dominated, convective hydrothermal system, with <380°C, low-salinity reservoir fluids at hydrostatic (mesothermal) pressure conditions. ‘Healed’ microfractures also trapped >600°C, hypersaline (35 wt% NaCleq) fluids of magmatic origin, with inferred minimum pressures of formation being 600–750 bar, which corresponds to fluid entrapment at 2.4–3.0 km depth. Al-in-hornblende geobarometry indicates that hornblende crystallization occurred at about 1.45 Ma (7.7–9.4 km depth) in the (marginal) eastern Takidani Granodiorite, but later (at 1.25 Ma) and shallower (6.5–7.0 km) near the core of the intrusion. The average rate of uplift across the Takidani Granodiorite from the time of hornblende crystallization has been 5.1–5.9 mm/yr (although uplift was about 7.5 mm/yr prior to 1.2 Ma), which is faster than average uplift rates in the Japan Alps (3 mm/yr during the last 2 million years). A temperature–depth–time window, when the Takidani Granodiorite had potential to host an HDR system, would have been when the internal temperature of the intrusive was cooling from 500°C to 400°C. Taking into account the initial (7.5 mm/yr) rate of uplift and effects of erosion, an optimal temperature–time–depth window is proposed: for 500°C at 1.54–1.57 Ma and 5.2±0.9 km (drilling) depth; and 400°C at 1.36–1.38 Ma and 3.3±0.8 km (drilling) depth, which is within the capabilities of modern drilling technologies, and similar to measured temperature–depth profiles in other active hydrothermal systems (e.g. at Kakkonda, Japan).  相似文献   

8.
A dacitic magma (64.5 wt.% SiO2), a mixture of phenocryst-rich rhyodacite and an aphyric mafic magma, was erupted during the recent 1991–1995 Mount Unzen eruptive cycle. The experimental and analytical results of this study reveal additional details about conditions in the premixing and postmixing magmas, and the nature of the mixing process. The preeruption rhyodacitic magma was at a temperature of 790±20°C according to Fe–Ti oxide phenocryst cores, and at a depth of 6 to 7 km (160 MPa) according to Al-in-hornblende geobarometry. The mafic magma that mixed with the rhyodacite is found as andesitic (54 to 62 wt.% SiO2) enclaves in the erupted magma and was essentially aphyric when intruded. Phase equilibria indicate that an aphyric andesite at 160 MPa is >1030°C (H2O-saturated) and possibly as high as 1130°C (2 wt.% H2O). The composition of the rhyodacite which was mixed with the andesite is estimated to lie between 67 and 69 wt.% SiO2. Using these compositions and temperatures, the temperature of the Unzen magma after mixing is estimated to be at least 850° to 870°C. The groundmass Fe–Ti oxide microphenocrysts and those in pargasite-bearing reaction zones around biotite phenocrysts both give 890±20°C temperatures; the oxide–oxide contacts give temperatures of 910±20°C. The 900±30°C postmixing temperatures are consistent with phase-equilibria experiments which show that the magma was not above 930°C at 160 MPa. Our Fe–Ti oxide reequilibration experiments suggest that the mixing of the two magmas began within a few weeks of the eruption, which is a shorter time than is calculated using available diffusion data. There is also evidence that some mixing took place much closer to the time of extrusion based on the presence of unrimmed biotite phenocrysts in the magma.  相似文献   

9.
Study of the opaque minerals from well No. 7, Krafla, indicates two mineral assemblages: (1) hydrothermally altered igneous minerals and (2) secondary minerals that have precipitated from the geothermal fluid at depths down to 2140 m, and at temperatures up to more than 340°C. Chief amongst the chemically precipitated minerals are pyrite, pyrrhotite and goethite, which is described here for the first time in an Icelandic geothermal drill hole.The geothermal system at Krafla has been periodically disturbed by the influx of volcanic emanations; this article attempts to interpret, by use of thermochemical calculations, the processes affecting the precipitated mineral assemblage.  相似文献   

10.
The chemical compositions of a total of 120 thermal water samples from four different tectonically distinct regions (Central, North, East and West Anatolia) of Turkey are presented and assessed in terms of geothermal energy potential of each region through the use of chemical geothermometers. Na–Ca–HCO3 type waters are the dominant water types in all the regions except that Na–Cl type waters are typical for the coastal areas of West Anatolia and for a few inland areas of West and Central Anatolia where deep water circulation exists. The discharge temperature of the springs ranges up to 100°C, and the bottom-hole temperatures in drilled wells up to 232°C. Geothermometry applications yield reservoir temperatures of about 125°C for Central Anatolia, 110°C for North Anatolia, 136°C for East Anatolia and 251°C for West Anatolia, the latter agreeing with some of the bottom hole temperatures measured in drilled wells. The results reveal that the highest geothermal energy potential in Turkey is associated with the West Anatolian extensional tectonics which provides a regional, deep-seated heat source and a widespread graben system allowing deep circulation of waters. The North Anatolian region, bounded to the south by the dextral North Anatolian Fault along which most of the geothermal sites are located, has the lowest energy potential, probably due to the restriction of the heat source to local magmatic activities confined to pull-apart basins. The East Anatolian region (undergoing contemporary compression) and the Central Anatolian region (where the compressional regime in the east is converted to the extensional regime in the west) have moderate energy potential. Although the recently active volcanoes suggest the presence, at depth, of still cooling magma chambers that are potential heat sources, the lack of well-developed fault systems is probably responsible for the comparatively low energy potential of these regions. Almost all the thermal waters of Turkey are saturated with respect to calcite and, hence, have a significant calcite scaling potential which is particularly high for West Anatolian waters.  相似文献   

11.
Dissolution of igneous feldspar and the formation and occurrence of secondary feldspar in tholeiitic basalts from the Hengill volcanic centre, in SW Iceland was studied by microprobe analysis of cuttings from two ca. 2000 m deep geothermal wells. Well NG-7 in Nesjavellir represents a geothermal system in a rift zone where the intensity of young, insignificantly altered intrusions increases with depth. Well KhG-1 in Kolviðarhóll represents the margin of a rift zone where the intensity of intrusives is lower and the intensity of alteration higher. This marginal well represents altered basaltic crust in an early retrograde state. The secondary plagioclase in both wells is mainly oligoclase, occurring in association with K-feldspar and chlorite±actinolite. The texture of this assemblage depends on the lithology and intensity of alteration. In Nesjavellir (NG-7) the composition of secondary albite-oligoclase is correlated with the host-rock composition. This connection is not apparent in more intensely altered samples from Kolviðarhóll (KhG-1). The influence of temperature on composition of secondary Na-feldspar is unclear in both wells although Ca is expected to increase with temperature. Any temperature dependence may be suppressed by the influence of rock composition in Nesjavellir and by retrograde conditions at Kolviðarhóll. The absence of clear compositional gradients between igneous plagioclase and secondary feldspar and between Na-feldspar and K-feldspar suggests that secondary feldspars formed by dissolution precipitation reactions.  相似文献   

12.
The Ischia geothermal system is hosted by silicic rocks of the Quaternary Potassic Roman Province, in southern Italy. Exploration drilling down to 1156 m depth in the mid-1950s provided information on boiling profiles (up to 250°C) and on the depth and permeability of the potential reservoirs. Discharge fluid samples were collected and analyzed to define the inflow of surrounding seawater (C1 ranges from 2.5 to 20 g/kg) into the system.Analyses of samples from surface manifestations and shallow wells collected during 1983 and 1988 point to the existence of three distinct mixing regimes, involving three water components. A dishomogeneous body of diluted water (Cl less than 2.5 g/kg), that occurs at depths > 700 m and reequilibrates at 240°C at least, is overlain by an aquifer of groundwater variably mixed with variably seawater (Cl from 4 to 10 g/kg), which tends to reequilibrate at 160°C. Steam-heated waters locally develop and act as dilutants of the rising geothermal fluids.Dilution, mixing, and evaporation of the ascending chloride fluids are supported by oxygen and hydrogen isotopic data the thermal waters being enriched in 18O and D with respect to local meteoric water by up to 7 and 30‰, respectively. The relative composition of the major cations in thermal solutions was used to discriminate the two main groups of thermal waters, the reservoir temperatures of which are estimated from the Na/K-gethermometer. K-Mg geothermometer indicates reequilibration in near-surface conditions.The isotopic composition of the fumarolic steam varies from −7 to −12‰ in ∂8O and from − 35 to − 70‰ in ∂D, in agreement with a deep mixed fluid that boils adiabatically from 240 to 80°C. The deuterium content of the H2O-H2 pair gives enrichment factor of about 830‰, corresponding to equilibrium temperature conditions slightly higher than the surface boiling temperatures. The ∂13C of CO2is almost constant at −4.5‰ (1δ=0.4), suggesting an important magmatic contribution, and the ∂18O values of CO2appears to in equilibrium with accompanying steam at the measured temperatures.The CO2/Ar and H2/Ar chemical ratios have been used to derive aquifer temperatures, the values obtained being consistent with those of solute geothermometers.  相似文献   

13.
Thermal waters hosted by Menderes metamorphic rocks emerge along fault lineaments in the Simav geothermal area. Thermal springs and drilled wells are located in the Eynal, Çitgöl and Na a locations, which are part of the Simav geothermal field. Studies were carried out to obtain the main chemical and physical characteristics of thermal waters. These waters are used for heating of residences and greenhouses and for balneological purposes. Bottom temperatures of the drilled wells reach 163°C with total dissolved solids around 2225 mg/kg. Surface temperatures of thermal springs vary between 51°C and 90°C. All the thermal waters belong to Na–HCO3–SO4 facies. The cold groundwaters are Ca–Mg–HCO3 type. Dissolution of host rock and ion-exchange reactions in the reservoir of the geothermal system shift the Ca–Mg–HCO3 type cold groundwaters to the Na–HCO3–SO4 type thermal waters. Thermal waters are oversaturated at discharge temperatures for aragonite, calcite, quartz, chalcedony, magnesite and dolomite minerals giving rise to a carbonate-rich scale. Gypsum and anhydrite minerals are undersaturated with all of the thermal waters. Boiling during ascent of the thermal fluids produces steam and liquid waters resulting in an increase of the concentrations of the constituents in discharge waters. Steam fraction, y, of the thermal waters of which temperatures are above 100°C is between 0.075 and 0.119. Reservoir pH is much lower than pH measured in the liquid phase separated at atmospheric conditions, since the latter experienced heavy loss of acid gases, mainly CO2. Assessment of the various empirical chemical geothermometers and geochemical modelling suggest that reservoir temperatures vary between 175°C and 200°C.  相似文献   

14.
Results of a chemical study of the fluids from drill holes and hot springs of Puga and Chumatang areas in the northwestern part of the Himalaya are presented and discussed in this paper. The thermal waters of Puga and Chumatang are of Na-HCO3-Cl and Na-HCO3 types, respectively. A comparison between these waters, their chemical classification and activity studies suggest a flow path within a quartzitic-schistose basement, containing quartz, K-feldspar and illite, and in clayey terrains containing montmorillonite and illite.The chemistry of thermal waters also indicate their association with magmatic activity. The chemical geothermometers indicate the possible existence of a geothermal reservoir at Puga with temperature ≈250°C. The Chumatang area has a comparatively cooler reservoir with a temperature of 150–180°C.  相似文献   

15.
The Platanares geothermal area in western Honduras consists of more than 100 hot springs that issue from numerous hot-spring groups along the banks or within the streambed of the Quebrada de Agua Caliente (brook of hot water). Evaluation of this geothermal area included drilling a 650-m deep PLTG-1 drill hole which penetrated a surface mantling of stream terrace deposits, about 550 m of Tertiary andesitic lava flows, and Cretaceous to lower Tertiary sedimentary rocks in the lower 90 m of the drill core.Fractures and cavities in the drill core are partly to completely filled by hydrothermal minerals that include quartz, kaolinite, mixed-layer illite-smectite, barite, fluorite, chlorite, calcite, laumontite, biotite, hematite, marcasite, pyrite, arsenopyrite, stibnite, and sphalerite; the most common open-space fillings are calcite and quartz. Biotite from 138.9-m depth, dated at 37.41 Ma by replicate 40Ar/39 Ar analyses using a continuous laser system, is the earliest hydrothermal mineral deposited in the PLTG-1 drill core. This mid-Tertiary age indicates that at least some of the hydrothermal alteration encountered in the PLTG-1 drill core occured in the distant past and is unrelated to the present geothermal system. Furthermore, homogenization temperatures (Th) and melting-point temperatures (Tm) for fluid inclusions in two of the later-formed hydrothermal minerals, calcite and barite, suggest that the temperatures and concentration of dissolved solids of the fluids present at the time these fluid inclusions formed were very different from the present temperatures and fluid chemistry measured in the drill hole.Liquid-rich secondary fluid inclusions in barite and caicite from drill hole PLTG-1 have Th values that range from about 20°C less than the present measured temperature curve at 590.1-m depth to as much as 90°C higher than the temperature curve at 46.75-m depth. Many of the barite Th measurements (ranging between 114° and 265°C) plot above the reference surface boiling-point curve for pure water assuming hydrostatic conditions; however, the absence of evidence for boiling in the fluid inclusions indicates that at the time the minerals formed, the ground surface must have been at least 80 m higher than at present and underwent stream erosion to the current elevation. Near-surface mixed-layer illite-smectite is closely associated with barite and appears to have formed at about the same temperature range (about 120° to 200°C) as the fluid-inclusion Thvalues for barite. Fluid-inclusion Th values for calcite range between about 136° and 213°C. Several of the calcite Th values are significantly lower than the present measured temperature curve. The melting-point temperatures (Tm) of fluid-inclusion ice yield calculated salinities, ranging from near zero to as much as 5.4 wt. % NaCl equivalent, which suggest that much of the barite and calcite precipitated from fluids of significantly greater salinity than the present low salinity Platanares hot-spring water or water produced from the drill hole.  相似文献   

16.
The Platanares geothermal area, Departamento de Copán, Honduras, is located within a graben that is complexly faulted. The graben is bounded on the north by a highland composed of Paleozoic (?) metamorphic rocks in contact with Cretaceous - Tertiary redbeds of unknown thickness. These are unconformably overlain by Tertiary andesitic lavas, rhyolitic ignimbrites, and associated sedimentary rocks. The volcanic rocks are mostly older than 14 Ma, and thus are too old to represent the surface expression of an active crustal magma body. Thermal fluids that discharge in the area are heated during deep circulation of meteoric water along faults in a region of somewhat elevated heat flow. Geothermometry based upon the chemical composition of thermal fluids from hot springs and from geothermal gradient coreholes suggests that the reservoir equilibrated at temperatures as high as 225 to 240°C, within the Cretaceous redbed sequence. Three continuously cored geothermal gradient holes have been drilled; fluids of about 165°C have been produced from two drilled along a NW-trending fault zone, from depths of 250 to 680 m. A conductive thermal gradient of 139°C/km, at a depth of 400 m, was determined from the third well, drilled 0.6 km west of that fault zone. These data indicate that the Platanares geothermal area holds considerable promise for electrical generation by moderate- to hightemperature geothermal fluids.  相似文献   

17.
Philippine geothermal systems occur in the vicinity of large Holocene calc-alkaline volcanic complexes. Wells drilled in these areas encountered multiple intrusions; the latest dikes are the subsurface manifestations of the youngest heat source. Commonly, at least two hydrothermal regimes are juxtaposed in a single area, with the latest being in equilibrium with the present temperature and chemical regime.Alteration by neutral-pH water is pervasive and abundant. A contact-metamorphic aureole also occurs near intrusives. Alteration due to acid-sulfate fluids is generally confined to permeable structures. Neutral-pH alteration is divided into four zones on the basis of key clay minerals, and two subzones are defined by calc-silicates. These are the smectite (ambient to 180°C), transition (180–230°C), illite (230–320°C) and biotite (270–340°C) zones. Subzones are defined by epidote (250–340°C) and amphibole (280–340°C). The four main zones of acid alteration are: kaolinite (ambient to 120°C), dickite ± kaolinite (120–200°C), dickite ± pyrophyllite (200–250°C), and pyrophyllite ± illite (230–320°C). Where relict high-temperature alteration reaches the surface, the area being drilled is usually the outflow zone of the present system.These hydrothermal mineral assemblages are used: (1) as geothermometers; (2) to assist in determining the depth at which the production casing will be set during drilling; (3) to estimate fluid pH and other chemical parameters; (4) to predict possible corrosion and scaling tendencies of the fluids; (5) as a measure of permeability and possible cold water influx into wells; (6) as a guide to field hydrology; and (7) to estimate roughly the thickness of the eroded overburden.  相似文献   

18.
The Grand Brûlé borehole intersects a thick pile of basaltic lavas, down to 1010 m, and a basic-ultrabasic intrusive complex, from 1010 to 3003.50 m.The lavas are, in general, unaltered except in two fractured zones, where hydrothermal fluids circulated at temperatures not exceeding 350 ° C. The main secondary minerals there are pyroxene, feldspar, epidote, actinolite and chlorite.The entire thickness of the intrusive body intersected contains secondary minerals representing three stages of cooling:
1. 1. A late magmatic episode (600–900°C) characterized by biotite, kaersutite, edenite and pargasite.
2. 2. A hydrothermal episode (T<- 350°C) characterized by epidote, albite, biotite, actinolite and chlorite.
3. 3. A phase of serpentinization (T≤ 350°C).
It is very likely that the two later events occurred simultaneously, with physical and chemical interference.  相似文献   

19.
Application of various chemical geothermometers and mixing models indicate underground temperatures of 260°C, 280°C and 265°C in the Geysir, Hveravellir and Landmannalaugar geothermal fields in Iceland, respectively. Mixing of the hot water with cold water occurs in the upflow zones of all these geothermal systems. Linear relations between chloride, boron and δ18O constitute the main evidence for mixing, which is further substantiated by chloride, silica and sulphate relations in the Geysir and Hveravellir fields.A new carbonate-silica mixing model is proposed which is useful in distinguishing boiled and non-boiled geothermal waters. This model can also be used to estimate underground temperatures using data from warm springs. This model, as well as the chloride-enthalpy model and the Na-Li, and CO2-gas geothermometers, invariably yield similar results as the quartz geothermometer sometimes also does. By contrast, the Na-K and the Na-K-Ca geothermometers yield low values in the case of boiling hot springs, largely due to loss of potassium from solution in the upflow. The results of these geothermometers are unreliable for mixed waters due to leaching subsequent to mixing.  相似文献   

20.
Previously unrecognized pulses of rhyolite volcanism occurred in the Salton Trough between 420 ± 8 ka and 479 ± 38 ka (2σ), based on high-spatial resolution U–Pb zircon geochronology. Presently, these rhyolite lavas, tuffs and shallow subvolcanic sills are buried to depths between ~ 1.6 and 2.7 km at ambient temperatures between 200 and 300 °C, and are overprinted by propylitic to potassic hydrothermal alteration mineral assemblages consisting of finely intergrown quartz, K-feldspar, chlorite, epidote, and minor pyrite. Alteration resistant geochemical indicators (whole-rock Nd-isotopes, zircon oxygen-isotopes) reveal that these rhyolites are derived from remelting of MORB-type crust that was chilled and hydrothermally altered by deep-circulating hydrothermal waters. U–Pb zircon dating confirms the presence of Bishop Tuff in well State 2-14 at ~ 1.7 km depth, approximately 5 km NE of the geothermal wells that penetrated the buried rhyolites. These results indicate accelerated subsidence towards the center of the Salton Trough, increasing from 2.2 mm/a to 3.8 mm/a. Based on these results, the present-day Salton Sea geothermal field is identified as a focus zone of episodic rhyolitic volcanism, intense heat flow and metamorphism that predates present-day geothermal activity and Holocene volcanism by at least ~ 400 ka.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号