共查询到20条相似文献，搜索用时 15 毫秒
1.
Recently, two novel binders, one by-product-based binder named as GM and one phosphate-based binder named as KMP, have emerged that can stabilize soils spiked with mixed lead and zinc contaminants. However, field evaluations of the stabilization of actual soils that contaminated with mixed zinc (Zn) and inorganic chloride (Cl?) using GM and KMP have not been performed yet. This study presents a pilot-scale field test to evaluate the performance of GM and KMP to stabilize these inorganic contaminants in soils at two locations in an abandoned industrial plating plant site. The field soils were stabilized and cured for 1, 3, 7, and 28 days and tested for dry density, dynamic cone penetration, soil pH, and leachability. Laboratory unconfined compression tests were performed, and the relationship between unconfined compressive strength and dynamic cone penetrometer index was assessed. The results showed that the strength of both the GM- and KMP-stabilized soils after 28-day curing improved significantly, and the leached Zn and Cl? concentrations were well below the corresponding remediation limits. In general, the KMP-stabilized soil demonstrated superior performance in terms of higher dry density, unconfined compressive strength, average dynamic cone penetration resistance, lower dynamic cone penetrometer index in the early curing stage (7 days), and lower leached Zn concentration under all curing times. In contrast, the GM exhibited superior immobilization of Cl? in the contaminated soil irrespective of the curing time. The results demonstrate that GM and KMP are promising binders for treating Zn- and Cl?-contaminated soils at plating and other industry sites with similar contaminants.
相似文献2.
针对非饱和土吸力测量与计算的困难,提出了一种利用土的电阻率结构参数预测基质吸力的方法。通过滤纸法测试重塑膨胀土的基质吸力,分析了非饱和土的基质吸力与体积含水率的关系,即土-水特征曲线的变化规律。在测试非饱和土横向与竖向电阻率的基础上,探讨了非饱和土的电阻率与其体积含水率的关系,并进一步研究了土的电阻率结构性参数 、 和 随体积含水率的变化规律。发现基质吸力与电阻率结构参数 之间存在良好的抛物线关系,利用这种关系可以准确预测非饱和土的基质吸力。利用土的电阻率结构参数预测吸力,避免了吸力量测与计算的困难,简单实用。 相似文献
3.
4.
In this study, the effect of diesel fuel contamination on the electrical properties of unsaturated soils was estimated in
the low frequency ranges. For the soils having 5% water content, the electrical resistivity increased with the diesel fuel
contents while the permittivity decreased at higher diesel contents. However, at 15% water content, the variation of electrical
properties was not significant possibly because most of the electric currents should occur through the pore water. The linear
relationship between the electrical resistivity and the diesel fuel contents in soil was developed at 5% water content, which
implied that the electrical resistivity could be used to quantify the extent of diesel fuel contamination in soil. The results
indicated that the electrical properties including the resistivity and the permittivity could give the reliable estimation
on the diesel contamination with the low water content in soil and the frequency applied below 1 MHz. 相似文献
5.
同位素密度静力触探仪（ND-CPT）是一种把同位素密度仪并入到静力触探仪的探头中,同时测量锥尖阻力、侧壁摩阻力、孔隙水压力和密度的新型原位测试仪器。根据ND-CPT测量的密度为 射线源和检测器之间回转椭球体内土体的平均密度 的原理,首先建立了可以计算回转椭球体内土体的平均密度 的后向散射模型和平均值模型,然后调查了ND-CPT贯入各种非均质地层时的测量密度 剖面与实际密度 剖面的区别,结果表明在地层分界处附近的测量密度 与实际密度 有较大差别,最后对ND-CPT在实际工程中测量的有明海底泥的测量密度 剖面进行了理解,得到了海底泥的实际密度 剖面。研究结果可为利用ND-CPT准确划分地层提供依据。 相似文献
6.
Isabelle Cousin Arlène Besson Hocine Bourennane Catherine Pasquier Bernard Nicoullaud Dominique King Guy Richard 《Comptes Rendus Geoscience》2009,341(10-11):859-867
The aim of this article is to present a strategy to interpret the hydraulic functioning of a small field area by using measurements of the soil electrical resistivity. The spatial soil electrical resistivity was recorded at a high resolution on a 2 ha area by the MultiContinous Electrical Profiling (MuCEP) device at two dates. These apparent electrical resistivity measurements were firstly interpreted in terms of local electrical resistivity by 1D inverse modelling to estimate the real resistivity of the soil. These interpreted electrical resistivity data were then transformed into soil water content values and soil water potential values by the use of independent punctual data of water content and the use of the water retention curve determined by laboratory data. Our analysis has permitted us to describe the spatial variability and temporal evolution of the hydraulic functioning at high resolution from electrical resistivity data. The interpretation of the water content and matric potential maps demonstrated that some soil hydraulic processes, such as lateral overland flow, can occur in the studied zone. They would never have been detected by local measurements of soil characteristics or by the use of the soil map. 相似文献
7.
In this study, the electrical resistivity of soil having different chemical weathering index (CWI) was measured, and the correlation
between CWI and the electrical resistivity was estimated. The electrical resistivity of soil varies with CWI of soil. The
difference in the electrical resistivities of soils having different weathering degrees is clear at lower water contents.
At the volumetric water contents estimated in this study, CWI could be described by a linear equation of electrical resistivity
with the constants related to the volumetric water content. The findings in this study suggest that the electrical resistivity
could be used as an effective alternative for estimating the weathering degree of soil. 相似文献
8.
In the territory of the Campania region (southern Italy), critical rainfall events periodically trigger dangerous fast slope movements involving ashy and pyroclastic soils originated by the explosive phases of the Mt. Somma-Vesuvius volcano and deposited along the surrounding mountain ranges. In this paper, an integration of engineering-geological and geophysical measurements is presented to characterize unsaturated pyroclastic samples collected in a test area on the Sarno Mountains (Salerno and Avellino provinces, Campania region). The laboratory analyses were aimed at defining both soil water retention and electrical resistivity curves versus water content. From the matching of the experimental data, a direct relationship between electrical resistivity and matric suction is retrieved for the investigated soil horizons typical of an ash-fall pyroclastic succession. The obtained relation turns out to be helpful in characterizing soils up to close saturation, which is a critical condition for the trigger of slope failure. In such a regime, the water content and the matric suction have small variations, while electrical resistivity variations can be appreciated in a larger range of values. For this reason, besides suction measurements on very small soil volumes through classical tensiometers, our analyses suggest the direct monitoring of in situ electrical resistivity values as an effective tool to recognise the hydrological state of larger and more representative soil volumes and to improve early warning of dangerous slope movements. 相似文献
9.
黄河口饱和粉土的电性特征及其工程地质应用 总被引：1，自引：0，他引：1
通过对形成于1964年～1976年位于黄河口潮坪区粉土层样品电阻率、井中电阻率和电阻率剖面的测试,分析了土的含水率、孔隙比、饱和度、孔隙水的电阻率、颗粒成分等因素对其导电性的影响。分析结果表明：影响该地区饱和粉土导电性的主要因素为土的孔隙率。随着孔隙率的增大,其含水率升高,电阻率降低,土的电阻率和相应孔隙率的关系可用拟合公式表达。基于此,利用电阻率法成功实现了不同深度粉土沉积层微结构的变化、波浪作用导致密实度不同的粉土层空间分布状况的原位测试。 相似文献
10.
11.
Use of a resistivity cone for detecting contaminated soil layers 总被引：11，自引：0，他引：11
A cone-penetration technique was developed to detect contaminated soil layers with electrolytes and NAPLs. In this study, laboratory and field experiments were performed to apply the technique. In the laboratory, the change in resistivity was quantitatively examined by adding salt or oil to soil samples. The results showed that the resistivity measurement was varied with an order of ppm for the electrolyte concentration in soil. It was found that the resistivity of sand increased with increasing oil concentration. The effect of oil content was stronger for lower water content of sand.
The results obtained from field experiments showed that the resistivity cone can be used for detecting the contaminated layer in soils whose background values are known. Particularly, the instrument can be used effectively for examining the effects of remediation, by measuring the resistivity of the ground before and after remediation, unless the soil fabric changes significantly during remediation procedures. 相似文献
12.
掺石灰黏土电阻率试验研究 总被引：3，自引：0，他引：3
利用4电极电阻率测量装置,在室内对各种灰土样的电阻率进行测试对比研究,揭示了不同因素如灰土比、含水率、饱和度、土的结构和土粒粒径等对灰土样电阻率的影响。在不同含水率（15 %、20 %、25 %和30 %）条件下,素土及其与不同石灰掺量（1:10、1:15和1:30）的混合,通过轻型击实试验后,测量其横向及竖向断面上的电阻率,研究电阻率与不同石灰配比击实土样的物理力学性质之间的关系。实验结果表明,当含水率在15 %~20 %之间时,较小的含水率增量引起混合土样电阻率的大幅度下降;当含水率约达到20 %后,其电阻率随含水率的继续增加而减小的幅度很小;在15 %含水率时,掺灰土电阻率比素土样高;在30 %含水率时,其电阻率低于素土样,而且掺量越大,电阻率越低;由于击实导致土体颗粒的结构重新排列,电阻率在横向上大于竖向;电阻率随着无侧限抗压强度的增加而增加,在电阻率大于50 ?•m时,电阻率随无侧限抗压强度的增加而减小;饱和度、干密度与电阻率呈负指数变化规律,孔隙率、孔隙比与电阻率呈指数变化规律;含水率对于电阻率的影响较为敏感。 相似文献
13.
黄土在应力作用下迂水时力学强度迅速下降 ,产生大范围的快速沉陷。这就是黄土的湿陷性 ,是黄土的诸多特性之一。鉴于对黄土湿陷性以往用各种实验室试验指标进行评价 ,这里提出运用动力触探和静载荷试验进行黄土湿陷性原位评价的一种简便的新方法。该方法的试验程序是 ,先用轻便可变动能触探仪在天然状态和饱水状态下进行触探试验 ,而后在触探孔完成静载荷压缩性试验。运用中国黄土高原黄土原位动力触探和静载荷试验测得的资料 ,详细分析了天然状态的黄土对探头阻力 qdnat,饱水状态的黄土对探头阻力 qdsat,实验室测得的湿陷性指数s压缩曲线参数 (即触探极限压力 ppf,触探蠕变压力ppl 和触探载荷模量Epn)的关系。结果证明所提出的方法适用于原位判定黄土的湿陷性。 相似文献
14.
The city of Burdur, which is built on an alluvium aquifer, is located in one of the most seismically active zones in southwestern
Turkey. The soil properties in the study site are characterized by unconsolidated and water-saturated sediments including
silty, clayey and sandy units, and shallow groundwater level is the other characteristic of the site. Thus, the city is under
soil liquefaction risk during a large earthquake. A resistivity survey including 189 vertical electrical sounding (VES) measurements
was carried out in 2000 as part of a multi-disciplinary project aiming to investigate settlement properties in Burdur city
and its vicinity. In the present study, the VES data acquired by using a Schlumberger array were re-processed with 1D and
2D inversion techniques to determine liquefaction potential in the study site. The results of some 1D interpretations were
compared to the data from several wells drilled during the project. Also, the groundwater level map that was previously obtained
by hydrological studies was extended toward north by using the resistivity data. 2D least-squares inversions were performed
along nine VES profiles. This provided very useful information on vertical and horizontal extends of geologic units and water
content in the subsurface. The study area is characterized by low resistivity distribution (<150 Ωm) originating from high
fluid content in the subsurface. Lower resistivity (3–30 Ωm) is associated with the Quaternary and the Tertiary lacustrine
sediments while relatively high resistivity (40–150 Ωm) is related to the Quaternary alluvial cone deposits. This study has
also shown that the resistivity measurements are useful in the estimation of liquefaction risk in a site by providing information
on the groundwater level and the fluid content in the subsurface. Based on this, we obtained a liquefaction hazard map for
the study area. The liquefaction potential was classified by considering the resistivity distributions from 2D inversion of
the VES profiles, the types of the sediments and the extended groundwater level map. According to this map, the study area
was characterized by high liquefaction hazard risk. 相似文献
15.
Effect of Soil Parameters on Dynamic Cone Penetration Indices of Laterite Sub-grade Soils from India
Varghese George Ch. Nageshwar Rao R. Shivashankar 《Geotechnical and Geological Engineering》2009,27(4):585-593
The focus of this study was on correlating the effect of grain-size, maximum dry-density (MDD), field moisture content, and
the void ratios on penetration measured using the dynamic cone penetrometer (DCP) for laterite soils blended with fines. Tests
were performed on soil samples compacted to MDD for moulding water contents set to the optimum moisture content (OMC), dry
of OMC, and wet of OMC un-soaked condition. The results indicated that an increase in the fines-content caused a decrease
in the MDD, and an increase in the OMC and the DCP penetration. Regressions were developed correlating various parameters. 相似文献
16.
Coupled theory of mixtures for clayey soils 总被引：4，自引：0，他引：4
In this work, elasto-plastic coupled equations are formulated in order to describe the time-dependent deformation of saturated cohesive soils (two-phase state). Formulation of these equations is based on the principle of virtual work and the theory of mixtures for inelastic porous media. The theory of mixtures for a linear elastic porous skeleton was first developed by Biot (Theory of elasticity and consolidation for a porous anisotropic solid, Journal of Applied Physics, 1955, 26, 188–185). An extension of Biot's theory into a nonlinear inelastic media was performed by Prevost (Mechanics of continuous porous media, International Journal of Engineering Science, 1980, 18, 787–800). The saturated soil is considered as a mixture of two deformable media, the solid grains and the water. Each medium is regarded as a continuum and follows its own motion. The flow of pore-water through the voids is assumed to follow Darcy's law. The coupled equations are developed for large deformations with finite strains in an updated Lagrangian reference frame. The coupled behavior of the two-phase materials (soil-water state) is implemented in a finite element program. A modified Cam-clay model is adopted and implemented in the finite element program in order to describe the plastic behavior of clayey soils. Penetration of a piezocone penetrometer in soil is numerically simulated and implemented into a finite element program. The piezocone penetrometer is assumed to be infinitely stiff. The continuous penetration of the cone is simulated by applying an incremental vertical movement of the cone tip boundary. Results of the finite element numerical simulation are compared with experimental measurements conducted at Louisiana State University using the calibration chamber. The numerical simulation is carried out for two cases. In the first case, the interface friction between the soil and the piezocone penetrometer is neglected. In the second case, interface friction is assumed between the soil and the piezocone. The results of the numerical simulations are compared with experimental laboratory measurements. 相似文献
17.
软土地基电渗固结理论分析与数值模拟 总被引：3，自引：0，他引：3
电渗固结是加速软土固结、提高地基承载力的有效技术。传统的电渗固结理论假设土体的物理力学、水力学和电学特性均匀稳定,其理论解答与试验结果差别较大。针对电渗固结处理过程,对土体位移场、渗流场和电场的耦合特征进行了理论分析,根据电荷守恒原理、水流连续原理和Biot固结理论,建立了电渗固结过程的多场耦合控制方程;考虑土体相关特性参数的非线性关系,开发了有限元软件用于分析电渗过程中电场强度、土体位移以及超静孔隙水压力的变化特征。计算结果与理论数据吻合较好,能够反映土体相关特性参数非线性关系对结果的影响。软件能够为电渗固结系统设计提供参考依据。 相似文献
18.
膨胀土是一种高塑性、强亲水的黏性土。由于黏土矿物含量较高,膨胀土颗粒的交换阳离子含量也较高,总比表面积较大,在电导率测试指标上反映是膨胀土的导电性随膨胀性的增大而增强。选取强、中、弱3种不同膨胀等级的代表性试样,采用无电极电阻率测定仪和便携式电导率探头,测试了膨胀土泥浆和孔隙水溶液电导率测试,采用原子吸收光谱仪检测了膨胀土孔隙水溶液中的离子种类、含量等。研究表明,膨胀土孔隙水溶液的导电性与膨胀土泥浆的导电性均随膨胀性增大而增大,膨胀土的电导率和自由膨胀率具有良好的线性关系,工程中可以利用这一原理进行膨胀土的快速判别。 相似文献
19.
近年来许多研究者致力于通过孔压静力触探(CPTU)确定土体的渗透系数,但是存在偏差大,而且不能从机制上清楚地解释孔压静力触探确定土体渗透系数的原因。为了应用孔压静力触探现场快速地确定土体的渗透系数,在总结前人对孔压静力触探确定土体渗透系数方法的研究基础上,提出孔压静力触探时锥头处呈球冠形孔隙水流动的计算模型,假定锥头处初始超孔隙水压力为负指数型分布,推导出土体渗透系数的表达式,并且结合现场实测数据,将所提出的方法与已有的方法进行对比分析。研究发现：所提出的方法扩大了现有方法的应用范围;渗透系数计算结果受锥头角度的影响较大,随着锥头角度的增大而增大;针对国际上通用的60°角的标准锥头,所提出的方法计算的渗透系数大于前人的方法,而且更接近室内外试验结果。 相似文献
20.
Assessment of soil salinization based on a low-cost method and its influencing factors in a semi-arid agricultural area,northwest China 总被引：13，自引：9，他引：4
An investigation of soil salinization was carried out in the Nanshantaizi area (Northwest China) with WET Sensor. This device can measure such soil parameters as bulk soil electrical conductivity, water content, and the pore water electrical conductivity that are important for soil salinization assessments. A distribution map of soil salinization was produced, and the factors influencing soil salinization and its processes were discussed in detail. The study shows that moderately salinized to salt soils are mainly observed in the alluvial plain, where groundwater level is high and lateral recharge water contains high salinity. Nanshantaizi is covered by slightly salinized soils. The soil salinization distribution estimated by WET Sensor is generally consistent with the actual levels of salinization. Soil salinity in Nanshantaizi is mostly of natural origin and accumulated salts could leach to deeper soils or aquifers by water percolation during irrigation. Groundwater evaporation, groundwater level depth and quality of recharge water are important factors influencing soil salinization in the alluvial plain. 相似文献