首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 156 毫秒
1.
Several mechanisms contribute to streambank failure including fluvial toe undercutting, reduced soil shear strength by increased soil pore‐water pressure, and seepage erosion. Recent research has suggested that seepage erosion of noncohesive soil layers undercutting the banks may play an equivalent role in streambank failure to increased soil pore‐water pressure. However, this past research has primarily been limited to laboratory studies of non‐vegetated banks. The objective of this research was to utilize the Bank Stability and Toe Erosion Model (BSTEM) in order to determine the importance of seepage undercutting relative to bank shear strength, bank angle, soil pore‐water pressure, and root reinforcement. The BSTEM simulated two streambanks: Little Topashaw Creek and Goodwin Creek in northern Mississippi. Simulations included three bank angles (70° to 90°), four pore‐water pressure distributions (unsaturated, two partially saturated cases, and fully saturated), six distances of undercutting (0 to 40 cm), and 13 different vegetation conditions (root cohesions from 0·0 to 15·0 kPa). A relative sensitivity analysis suggested that BSTEM was approximately three to four times more sensitive to water table position than root cohesion or depth of seepage undercutting. Seepage undercutting becomes a prominent bank failure mechanism on unsaturated to partially saturated streambanks with root reinforcement, even with undercutting distances as small as 20 cm. Consideration of seepage undercutting is less important under conditions of partially to fully saturated soil pore‐water conditions. The distance at which instability by undercutting became equivalent to instability by increased soil pore‐water pressure decreased as root reinforcement increased, with values typically ranging between 20 and 40 cm at Little Topashaw Creek and between 20 and 55 cm at Goodwin Creek. This research depicts the baseline conditions at which seepage undercutting of vegetated streambanks needs to be considered for bank stability analyses. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

2.
Seepage erosion in layered stream bank material   总被引：1，自引：0，他引：1  
Current stream restoration practices often require anthropogenic manipulation of natural field soils to reconstruct stream banks in the absence of stabilizing vegetation. For this study, researchers conducted laboratory experiments on reconstructed, non‐vegetated stream banks with layered soils experiencing seepage. The objective of the study was to determine the effect of seepage, pore water pressure, and bank geometry on erosion and bank stability of layered streambanks. The experimental design consisted of an intermediate‐size soil lysimeter packed with a sandy clay loam top soil and an underlying fine sand layer at three bank slopes (90°, 45° and 26°). Shallow groundwater flow and seepage resulted in bank failure of geometrically stable banks. Pop out failures, liquid deformation, and piping were all observed failure mechanisms in the underlying sand material, dependent on the bank angle. Groundwater seepage processes created small‐scale failures of the underlying sand leading to larger‐scale failures of the overlying sandy clay loam. The underlying sand layer eroded according to the initial bank angle and change in overburden loading. The overlying loam layer failed along linear failure planes. The gradually sloped bank (i.e. 26° slope) failed faster, hypothesized to be due to less confining pressure and greater vertical seepage forces. Researchers analyzed the laboratory experiments using the Bank Stability and Toe Erosion Model, version 4·1. The model calculated an accurate shear surface angle similar to the failure angle observed in the lysimeter tests. The model predicted failure only for the undercut 90° bank slope, and indicated stable conditions for the other geometries. Steeper initial bank slopes and undercut banks decreased the bank factor of safety. The observed failure mechanisms and measured saturation data indicated an interaction between overburden pressure, seepage forces, and bank slope on bank stability. Future bank stability modeling would benefit by incorporating lateral seepage erosion and soil liquefaction prediction calculations. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

3.
The majority of sediment leaving catchments may be from streambank failure. Seepage erosion of unconsolidated sand above a restrictive layer is an important erosion process in incised streams that leads to streambank failure by undercutting banks. The objective of this study was to determine the impact of soil properties on seepage erosion and the resulting streambank failure. Seepage flow and sediment concentrations were measured in situ at eight locations along the banks of a deeply incised stream in northern Mississippi. Using field observations as a guide, the soil profile conditions of a shallow (45 cm) streambank, consisting of 30 cm of topsoil, a 10 cm conductive layer, and a 5 cm restrictive layer, were mimicked in laboratory lysimeter experiments to quantify the hydrologic properties controlling seepage erosion and bank failure under a 40 cm head. The time to flow initiation and the flow rate were linearly related to the slope of the restrictive layer. Seepage erosion began within minutes of flow initiation and resulted in substantial (3 to 34 cm) undercutting of the bank. Sediment concentrations of seeps were as high as 660 g l?1 in situ and 4500 g l?1 in the lysimeters. Sediment concentrations were related to the layer slope, thereby indicating the importance of detailed site characterization. The USDA‐ARS Streambank Stability model demonstrated the increase in instability of banks due to undercutting by seepage erosion, but failed to account for the sediment loss due to sapping for stable banks and overestimated the sediment loads for failed banks. Published in 2006 by John Wiley & Sons, Ltd.  相似文献   

4.
The ability to predict the stability of eroding riverbanks is a prerequisite for modelling alluvial channel width adjustment and a requirement for predicting bank erosion rates and sediment yield associated with bank erosion. Mass‐wasting of bank materials under gravity occurs through a variety of specific mechanisms, with a separate analysis required for each type of failure. This paper presents a computer program for the analysis of the stability of steep, cohesive riverbanks with respect to planar‐type failures. Planar‐type failures are common along stream channels destabilized by severe bed degradation. Existing stability analyses for planar‐type failures have a number of limitations that affect their physical basis and predictive ability. The computer program presented here is based on an analysis developed by Darby and Thorne. The software takes account of the geotechnical characteristics of the bank materials, the shape of the bank profile, and the relative elevations of the groundwater and surface water to estimate stability with respect to mass failure along a planar‐type failure surface. Results can be displayed either in terms of a factor of safety (ratio of resisting to driving forces), or probability of failure. The computer analysis is able to determine the relative amounts of bed degradation and bank‐toe erosion required to destabilize an initially stable bank. Data for the analysis are supplied in the form of either HEC‐2 hydrographic survey data files or user‐supplied bank profile data, in conjunction with user‐supplied geotechnical parameter values. Some examples, using data from the Upper Missouri River in Montana, are used to demonstrate potential applications of the software. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

5.
Streambank retreat can be a significant contributor to total sediment and nutrient loading to streams. Process-based bank stability models, such as the Bank Stability and Toe Erosion Model (BSTEM), have been used to determine critical factors affecting streambank erosion and failure such as riparian vegetation and to estimate retreat rates over time. BSTEM has been successfully applied on a number of cohesive streambanks, but less so on composite banks consisting of both cohesive and noncohesive soils in highly sinuous streams. Composite streambanks can exhibit rapid and episodic bank retreat. The objectives of this research were twofold: (i) develop and apply simplified procedures for estimating root cohesion based on above- and below-ground biomass estimates and (ii) systematically apply BSTEM to a series of 10 composite streambanks distributed along the Barren Fork Creek in eastern Oklahoma to assess model sensitivity to root cohesion and model performance in predicting retreat. This research aimed to document the influence of riparian conservation practices on bank retreat rates and evaluated simplistic methods for incorporating such practices into such process-based models. Sites modeled included historically unprotected sites with no riparian vegetation and historically protected sites with riparian vegetation present during all or part of the 2003 to 2010 study period. The lateral retreat ranged from 4.1 to 74.8 m across the 10 sites and was largest at the historically unprotected sites in which retreat averaged 49.2 m. Protected sites had less bank retreat but with more variability in retreat rates per year. With calibration focused on the erodibility parameters, the model was able to match both the observed total amount of retreat as well as the timing of retreat at both the protected and unprotected sites as derived from aerial imagery. During calibration BSTEM was not sensitive to the specific value of the soil cohesion or the additional soil cohesion added due to roots for the cohesive topsoil layer, suggesting that the proposed simplified techniques could be used to estimate root cohesion values. The BSTEM modeling also provided an advantageous assessment tool for evaluating retreat rates compared to in situ bank retreat measurements due to the magnitude and episodic nature of streambank erosion and failures. Process-based models, such as BSTEM, may be necessary to incrementally model bank retreat in order to quantify actual streambank retreat rates and understand mechanisms of failure for the design of stabilization projects.  相似文献   

6.
We present a geotechnical stability analysis for the planar failure of riverbanks, which incorporates the effects of root reinforcement and surcharge for mature stands of woody riparian vegetation. The analysis relies on a new method of representing the root distribution in the soil, which evaluates the effects of the vegetation's position on the bank. The model is used in a series of sensitivity analyses performed for a wide range of bank morphological (bank slope and height) and sedimentological (bank cohesion and friction angle) conditions, enabling discrimination of the types of bank environment for which vegetation has an effect on bank stability. The results indicate that woody vegetation elements have a maximal impact on bank stability when they are located at the ends of the incipient failure plane (i.e. at the bank toe or at the intersection of the failure plane with the floodplain) and that vegetation has a greater effect on net bank stability when it is growing on low, shallow, banks comprised of weakly cohesive sediments. However, the magnitude of these effects is limited, with vegetation typically inducing changes (relative to non‐vegetated banks) in simulated factors of safety of less than 5%. If correct, this suggests that the well documented effects of vegetation on channel morphology must be related to alternative process mechanisms (such as the interaction of vegetation with river flows) rather than the mechanical effects of vegetation on bank failure, except in special cases where the equivalent non‐vegetated bank has a highly marginal stability status. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

7.
The stability of a river bank depends on the balance of forces, motive and resistive, associated with the most critical mechanism of failure. Many mechanisms are possible and the likelihood of failure occurring by any particular one depends on the size, geometry and structure of the bank, the engineering properties of the bank material, the hydraulics of flow in the adjacent channel and climatic conditions. Rivers flowing through alluvial deposits often have a composite structure of cohesionless sand and gravel overlain by cohesive silt/clay. Bank erosion occurs by fluvial entrainment of material from the lower, cohesionless bank at a much higher rate than material from the upper, cohesive bank. This leads to undermining that produces cantilevers of cohesive material. Upper bank retreat takes place predominantly by the failure of these cantilevers. Three mechanisms of failure have been identified: shear, beam and tensile failure. The stability of a cantilever may be analysed using static equilibrium and beam theory, and dimensionless charts for cantilever stability constructed. Application of the charts requires only a few simple measurements of cantilever geometry and soil properties. In this analysis the effects of cracks and fissures in the soil must be taken into account. These cracks seriously weaken the soil and can invalidate a stability analysis by affecting the shape of the failure surface. Following mechanical failure, blocks of soil must be removed from the basal area by fluvial entrainment if rapid undermining and cantilever generation are to continue. Hence, the rate of bank retreat is fluvially controlled, even though the mechanism of failure of the upper bank is not directly fluvial in nature. This cycle of bank erosion: undermining, cantilever failure and fluvial scour of the toe, operates over several flood events and has important implications for river engineering, channel changes, and the movement of sediment through fluvial systems.  相似文献   

8.
We measured the effect of wet meadow vegetation on the bank strength and failure mechanics of a meandering montane meadow stream, the South Fork of the Kern River at Monache Meadow, in California's Sierra Nevada. Streambanks colonized by ‘wet’ graminoid meadow vegetation were on average five times stronger than those colonized by ‘dry’ xeric meadow and scrub vegetation. Our measurements show that strength is correlated with vegetation density indicators, including stem counts, standing biomass per unit area, and the ratio of root mass to soil mass. Rushes appear better than sedges at stabilizing coarse bar surfaces, while sedges are far more effective at stabilizing actively eroding cut banks. Wet meadow floodplain vegetation creates a composite cut bank configuration (a cohesive layer overlying cohesionless materials) that erodes via cantilever failure. Field measurements and a geotechnical model of cantilever stability show that by increasing bank strength, wet meadow vegetation increases the thickness, width, and cohesiveness of a bank cantilever, which, in turn, increases the amount of time required to undermine, detach, and remove bank failure blocks. At Monache Meadow, it takes approximately four years to produce and remove a 1 m wide wet meadow bank block. Wet meadow vegetation limits bank migration rates by increasing bank strength, altering bank failure modes, and reducing bank failure frequency. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

9.
Quantifying bank storage of variably saturated aquifers   总被引：1，自引：0，他引：1  
Li H  Boufadel MC  Weaver JW 《Ground water》2008,46(6):841-850
Numerical simulations were conducted to quantify bank storage in a variably saturated, homogenous, and anisotropic aquifer abutting a stream during rising stream stage. Seepage faces and bank slopes ranging from 1/3 to 100/3 were simulated. The initial conditions were assumed steady-state flow with water draining toward the stream. Then, the stream level rose at a constant rate to the specified elevation of the water table given by the landward boundary condition and stayed there until the system reached a new steady state. This represents a highly simplified version of a real world hydrograph. For the specific examples considered, the following conclusions can be made. The volume of surface water entering the bank increased with the rate of stream level rise, became negligible when the rate of rise was slow, and approached a positive constant when the rate was large. Also, the volume decreased with the dimensionless parameter M (the product of the anisotropy ratio and the square of the domain's aspect ratio). When M was large (>10), bank storage was small because most pore space was initially saturated with ground water due to the presence of a significant seepage face. When M was small, the seepage face became insignificant and capillarity began to play a role. The weaker the capillary effect, the easier for surface water to enter the bank. The effect of the capillary forces on the volume of surface water entering the bank was significant and could not be neglected.  相似文献   

10.
Cliff stability within the Pembrokeshire Coast National Park was evaluated using a numerical model applied at four sites representative of rock mass failure phenomena and major sedimentary geological sequences. The sites were: Mill Bay, (Old Red Sandstone); St Govan's Head, Carboniferous Limestone (Dinantian); Druidston, Millstone Grit (Namurian) and Lower Coal Measures (Westphalian); and Wiseman's Bridge, Lower Coal Measures (Westphalian). The study integrated a range of geotechnical parameters, measured in the field and laboratory, into a model to predict the likely failure mechanisms. The model is based on the existence of rock prisms delineated by structural parameters, i.e. joints, bedding planes and critical tension fractures behind the cliff face. An iterative approach is used to define the dip of the most probable, stepped failure surface at the base of any potentially unstable multiblock system and to calculate the sliding and toppling forces for each block in the cliff mass. Prediction compared favourably with field observations at three of the four selected sites, i.e. Druidston, St Govan's Head and Wiseman's Bridge. At Druidston sliding is predicted and dominates in the basal blocks, whilst toppling is confined to the upper cliff and is dependent on movement of the lower structural units. St Govan-s Head is shown to have a low risk of toppling and sliding and this was predicted except where basal undercutting reaches a depth of 1·0 m or lateral forces exceed 100 kN m−2 when failure could occur. Copyright © 1998 John Wiley & Sons, Ltd.  相似文献   

11.
Riverbanks along the Arno River have been investigated with the aims of de?ning the main mechanisms of failure and retreat, their spatial distribution, and their causes. Geomorphological aspects were investigated by a reconnaissance of riverbank processes, for a number (26) of representative sites. Laboratory and in situ tests were then performed on a selected number of riverbanks (15). Based on the material characteristics, six main typologies of riverbanks have been de?ned, with homogeneous ?ne‐grained and composite banks representing the most frequent types. Slab‐type failures are the most frequent mechanism observed on ?ne‐grained banks, while cantilever failures prevail on composite banks. The role of river stage and related pore water pressure distributions in triggering the main observed mechanisms of failure has been investigated using two different types of stability analysis. The ?rst was conducted for 15 riverbanks, using the limit equilibrium method and considering simpli?ed hypotheses for pore water pressure distribution (annulment of negative pore pressures in the portion of the bank between low water stage and peak stage). Stability conditions and predicted mechanisms of failure are shown to be in reasonably good agreement with ?eld observations. Three riverbanks, representative of the main alluvial reaches of the river, were then selected for a more detailed bank stability analysis, consisting of: (a) de?nition of characteristic hydrographs of the reach with different return periods; (b) modelling of saturated and unsaturated ?ow using ?nite element seepage analysis; and (c) stability analysis with the limit equilibrium method, by adopting pore water pressure values derived from the seepage analysis. The results are compared to those obtained from the previous simpli?ed analysis, and are used to investigate the different responses, in terms of stability, to different hydrological and riverbank conditions. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

12.
In meandering rivers cut into bedrock, erosion across a channel cross‐section can be strongly asymmetric. At a meander apex, deep undercutting of the outer bank can result in the formation of a hanging cliff (which may drive hillslope failure), whereas the inner bank adjoins a slip‐off slope that connects to the hillslope itself. Here we propose a physically‐based model for predicting channel planform migration and incision, point bar and slip‐off slope formation, bedrock abrasion, the spatial distribution of alluvial cover, and adaptation of channel width in a mixed bedrock‐alluvial channel. We simplify the analysis by considering a numerical model of steady, uniform bend flow satisfying cyclic boundary conditions. Thus in our analysis, ‘sediment supply’, i.e. the total volume of alluvium in the system, is conserved. In our numerical simulations, the migration rate of the outer bank is a specified parameter. Our simulations demonstrate the existence of an approximate state of dynamic equilibrium corresponding to a near‐solution of permanent form in which a bend of constant curvature, width, cross‐sectional shape and alluvial cover distribution migrates diagonally downward at constant speed, leaving a bedrock equivalent of a point bar on the inside of the bend. Channel width is set internally by the processes of migration and incision. We find that equilibrium width increases with increasing sediment supply, but is insensitive to outer bank migration rate. The slope of the bedrock point bar varies inversely with both outer bank migration rate and sediment supply. Although the migration rate of the outer bank is externally imposed here, we discuss a model modification that would allow lateral side‐wall abrasion to be treated in a manner similar to the process of bedrock incision. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

13.
Numerous processes may instigate bank retreat and the consequent collection of failed cohesive materials at the bank toe. Cohesion between the failed material and the substrate can provide additional strength to resist direct fluvial entrainment. Failed, cohesive material can act as a form of natural bank‐toe protection by consuming and diverting flow energy that may otherwise be used to further scour the basal zone of incising channels. Investigations in Goodwin Creek, Mississippi, have revealed the existence of apparent cohesion between failed, cohesive blocks and their underlying surface. The method used to assess this cohesion involved a pulley system mounted on a tripod and supporting a load cell. Mean and maximum apparent‐cohesion values of 1·08 kPa and 2·65 kPa, respectively, were measured in this way, identifying a source that bonds blocks to the underlying surface. Cohesion values and types vary spatially and temporally. Tensiometric tests beneath blocks suggest that cohesion resulting from matric suction alone may be as much as 3·5 kPa in summer and 1·8 kPa in winter. Apparent cohesion is believed to have been sufficient to help prevent removal of the largest blocks by a peak flow of 66·4m3/s on 23 September 1997. Maximum excess shear stress required to entrain a D75 block can be augmented by as much as 97% by the presence of apparent cohesion at the block–substrate interface when compared with a condition with zero apparent cohesion at the block underside. Given these findings, it is no longer sufficient to estimate block entrainment in the basal area from block size or bed roughness alone, as in a Shields‐type approach. Copyright © 2001 John Wiley & Sons, Ltd.  相似文献   

14.
Cross-sections of 16 straight sandbed streams in Minnesota, Iowa, and Nebraska were surveyed. Two stratigraphic horizons were found in the banks at each site, an upper cohesive unit usually composed of silt and clay and a lower unit composed of sand. Bank erosion on these rivers occurs when the upper cohesive unit is undercut by scour at bends. The overhanging cohesive block fails by beam or cantilever failure. As upper bank failure is a direct result of undercutting, the stability and rate of retreat of the bank are largely determined by erosion of the sandy part of the bank. The cohesive layer has little influence on bank retreat and width adjustment on the rivers studied here. A quantitative lateral sediment transport model developed by Parker (1978a) is used to calculate the steady-state geometry of the sandy part of the bank. Results are obtained for the shape, length, and height of the sandy part of the bank. The model predicts the length of the bank fairly well, and the theoretical equation for the height of the bank is of the correct form. The model, however, overestimates the slope of the bank. The height of the sandy part of the bank (Db) is approximately equal to the depth of the mean annual flow. Since Db is determined by the lateral sediment transport model, the width (W) may be obtained from the equation of continuity (Q = WDbV), published flow (Q) data, and a resistance equation for the mean velocity, V. The calculated widths are similar to those measured in the field.  相似文献   

15.
  相似文献   

16.
Geomorphological process research demands quantitative information on erosion and deposition event timing and magnitude, in relation to fluctuations in the suspected driving forces. This paper establishes a new measurement principle – thermal consonance timing (TCT) – which delivers clearer, more continuous and quantitative information on erosion and deposition event magnitude, timing and frequency, to assist understanding of the controlling mechanisms. TCT is based on monitoring the switch from characteristically strong temperature gradients in sediment, to weaker gradients in air or water, which reveals the moment of erosion. The paper (1) derives the TCT principle from soil micrometeorological theory; (2) illustrates initial concept operationalization for field and laboratory use; (3) presents experimental data for simple soil erosion simulations; and (4) discusses initial application of TCT and perifluvial micrometeorology principles in the delivery of timing solutions for two bank erosion events on the River Wharfe, UK, in relation to the hydrograph. River bank thermal regimes respond, as soil temperature and energy balance theory predicts, with strong horizontal thermal gradients (often >1 K cm?1 over 6·8 cm). TCT fixed the timing of two erosion events, the first during inundation, the second 19 h after the discharge peak and 13 h after re‐emergence from the flow. This provides rare confirmation of delayed bank retreat, quantifies the time‐lag involved, and suggests mass failure processes rather than fluid entrainment. Erosion events can be virtually instantaneous, implying ‘catastrophic retreat’ rather than ‘progressive entrainment’. Considerable potential exists to employ TCT approaches for: validating process models in several geomorphological contexts; assisting process identification and improving discrimination of competing hypotheses of process dominance through high‐resolution, simultaneous analysis of erosion and deposition events and driving forces; defining shifting erodibility and erosion thresholds; refining dynamic linkages in event‐based sediment budget investigations; and deriving closer approximations to ‘true’ erosion and deposition rates, especially in self‐concealing scour‐and‐fill systems. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

17.
Knowledge of the mechanisms of rain‐induced shallow landslides can improve the prediction of their occurrence and mitigate subsequent sediment disasters. Here, we examine an artificial slope's subsurface hydrology and propose a new slope stability analysis that includes seepage force and the down‐slope transfer of excess shear forces. We measured pore water pressure and volumetric water content immediately prior to a shallow landslide on an artificial sandy slope of 32°: The direction of the subsurface flow shifted from downward to parallel to the slope in the deepest part of the landslide mass, and this shift coincided with the start of soil displacement. A slope stability analysis that was restricted to individual segments of the landslide mass could not explain the initiation of the landslide; however, inclusion of the transfer of excess shear forces from up‐slope to down‐slope segments improved drastically the predictability. The improved stability analysis revealed that an unstable zone expanded down‐slope with an increase in soil water content, showing that the down‐slope soil initially supported the unstable up‐slope soil; destabilization of this down‐slope soil was the eventual trigger of total slope collapse. Initially, the effect of apparent soil cohesion was the most important factor promoting slope stability, but seepage force became the most important factor promoting slope instability closer to the landslide occurrence. These findings indicate that seepage forces, controlled by changes in direction and magnitude of saturated and unsaturated subsurface flows, may be the main cause of shallow landslides in sandy slopes. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

18.
Comprehensive empirical data of the response of unstable streams over a range of environmental conditions are unavailable. In this study, as a substitute for empirical data, a physically based numerical model of channel evolution is used in a range of numerical simulation experiments designed to predict the sensitivity of channel response to changes in control variables. The scope of the study is limited by the scope of the numerical model which applies to straight, sand-bed streams with cohesive bank materials that have been destabilized by sediment starvation and evolve towards equilibrium through bed degradation followed by channel widening. Results are presented for stable and unstable channel conditions. Stable channel depths are most sensitive to channel discharge, though the critical threshold shear stress for the entrainment of cohesive bank materials and discharge are both significant in determining the width. The sediment load, channel gradient, bank material cohesion, size of failed bank material aggregates and the initial bank height have sensitivities an order of magnitude smaller than discharge for both width and depth. Variations in bed material characteristics within the sand-size range are found to have little impact on simulated stable channel morphology. For unstable channels, the relative dominance of parameter sensitivities is examined in the context of an empirical-conceptual model of channel evolution proposed by Thorne and Osman (1988), to highlight the relationships between parameter dominance, time, and the processes and forms characterizing individual stages of channel evolution. Rates of change with time of width and depth sensitivity parameters for five tested independent variables (discharge, sediment supply, channel gradient, bank material cohesion and bed material size) are found to vary as a function of time, such that different stages of channel evolution are characterized by variations in the relative dominance of tested variables. The results support the hypothesis proposed by Thorne and Osman (1988) that the critical bank height required to initiate mass-wasting and widening may be regarded as a geomorphic threshold.  相似文献   

19.
Stochastic erosion of composite banks in alluvial river bends   总被引：2，自引：0，他引：2       下载免费PDF全文
The erosion of composite river banks is a complex process involving a number of factors including fluvial erosion, seepage erosion, and cantilever mass failure. To predict the rate of bank erosion with these complexities, a stochastic bank erosion model is suitable to define the probability distribution of the controlling variables. In this study, a bank erosion model in a river bend is developed by coupling several bank erosion processes with an existing hydrodynamic and morphological model. The soil erodibility of cohesive bank layers was measured using a submerged jet test apparatus. Seasonal bank erosion rates for four consecutive years at a bend in the Brahmaputra River, India, were measured by repeated bankline surveys. The ability of the model to predict erosion was evaluated in the river bend that displayed active bank erosion. In this study, different monsoon conditions and the distribution functions of two variables were considered in estimating the stochastic bank erosion rate: the probability of the soil erodibility and stochastic stage hydrographs for the nth return period river stage. Additionally, the influences of the deflection angle of the streamflow, longitudinal slope of river channel, and bed material size on bank erosion rate were also investigated. The obtained stochastic erosion predictions were compared with the observed distribution of the annual‐average bank erosion rate of 45 river bends in the Brahmaputra River. The developed model appropriately predicted the short‐term morphological dynamics of sand‐bed river bends with composite banks. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

20.
Rill bank collapse is an important component in the adjustment of channel morphology to changes in discharge and sediment flux. Sediment inputs from bank collapse cause abrupt changes in flow resistance, flow patterns and downstream sediment concentrations. Generally, bank retreat involves gradual lateral erosion, caused by flow shear stress, and sudden bank collapse, triggered by complex interactions between channel flow and bank and soil water conditions. Collapse occurs when bank height exceeds the critical height where gravitational forces overcome soil shear strength. An experimental study examined conditions for collapse in eroding rill channels. Experiments with and without a deep water table were carried out on a meandering rill channel in a loamy sand and sandy loam in a laboratory flume under simulated rainfall and controlled runon. Different discharges were used to initiate knickpoint and rill incision. Soil water dynamics were monitored using microstandpipes, tensiometers and time domain reflectometer probes (TDR probes). Bank collapse occurred with newly developed or rising pre‐existing water tables near rill banks, associated with knickpoint migration. Knickpoint scour increased effective bank height, caused positive pore water pressure in the bank toe and reduced negative pore pressures in the unsaturated zone to near zero. Matric tension in unsaturated parts of the bank and a surface seal on the ‘interrill’ zone behind the bank enhanced stability, while increased effective bank height and positive pore water pressure at the bank toe caused instability. With soil water contents >35 per cent (sandy loam) and >23 per cent (loamy sand), critical bank heights were 0·11–0·12 m and 0·06–0·07 m, respectively. Bank toe undercutting at the outside of the rill bends also triggered instability. Bank displacement was quite different on the two soils. On the loamy sand, the failed block slid to the channel bed, revealing only the upper half of the failure plane, while on the sandy loam the failed block toppled forwards, exposing the failure plane for the complete bank height. This study has shown that it is possible to predict location, frequency and magnitude of the rill bank collapse, providing a basis for incorporation into predictive models for hillslope soil loss or rill network development. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号