共查询到20条相似文献，搜索用时 578 毫秒
1.
Modelling exterior unreinforced beam‐column joints in seismic analysis of non‐ductile RC frames 
下载免费PDF全文
下载免费PDF全文 The seismic response of non‐ductile reinforced concrete (RC) buildings can be affected by the behaviour of beam‐column joints involved in the failure mechanism, especially in typical existing buildings. Conventional modelling approaches consider only beam and column flexibility, although joints can provide a significant contribution also to the overall frame deformability. In this study, the attention is focused on exterior joints without transverse reinforcement, and a possible approach to their modelling in nonlinear seismic analysis of RC frames is proposed. First, experimental tests performed by the authors are briefly presented, and their results are discussed. Second, these tests, together with other tests with similar features from literature, are employed to calibrate the joint panel deformability contribution in order to reproduce numerically the experimental joint shear stress–strain behaviour under cyclic loading. After a validation phase of this proposal, a numerical investigation of the influence of joints on the seismic behaviour of a case study RC frame – designed for gravity loads only – is performed. The preliminary failure mode classification of the joints within the analysed frame is carried out. Structural models that (i) explicitly include nonlinear behaviour of beam‐column joints exhibiting shear or anchorage failure or (ii) model joints as elements with infinite strength and stiffness are built and their seismic performance are assessed and compared. A probabilistic assessment based on nonlinear dynamic simulations is performed by means of a scaling approach to evaluate the seismic response at different damage states accounting for uncertainties in ground‐motion records. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
2.
Analysis of RC slab–beam–column sub‐assemblages subjected to bidirectional lateral cyclic loading using a new 3D macroelement 下载免费PDF全文
下载免费PDF全文 An existing two‐dimensional macroelement for reinforced concrete beam–column joints is extended to a three‐dimensional macroelement. The three‐dimensional macroelement for beam–column joints consists of six rigid interface plates and uniaxial springs for concrete, steel, and bond–slip, which model the inside of a beam–column joint. The mechanical models for the materials and the stiffness equation for the springs are also presented. To validate the model, we used test results from three slab–beam–column sub‐assemblages subjected to bi‐lateral cyclic load. It is revealed that the new joint model is capable of capturing the strength of beam–column joints and the bidirectional interaction in joint shear response, including the concentration of damage in the beam–column joint, the pinching nature in hysteretic behavior, the stiffness degradation, and strength deterioration resulting from cyclic and bidirectional loading. Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
3.
Behaviour and modelling of partial‐strength beam‐to‐column composite joints for seismic applications
A refined component model is proposed to predict the inelastic monotonic response of exterior and interior beam‐to‐column joints for partial‐strength composite steel–concrete moment‐resisting frames. The joint typology is designed to exhibit ductile seismic response through plastic deformation developing simultaneously in the column web panel in shear, the bolted end‐plate connection, the column flanges in bending and the steel reinforcing bars in tension. The model can handle the large inelastic deformations consistent with high ductility moment‐resisting frames. Slip response between the concrete slab and the beams was taken into account. A fibre representation was adopted for the concrete slab to accurately capture the non‐uniform stress distribution and progressive crushing of the concrete at the interface between the concrete slab and the column flange. The model is validated against results from full‐scale subassemblages monotonic physical tests performed at the University of Pisa, Italy. A parametric study is presented to illustrate the capabilities of the model and the behaviour of the joints examined. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
4.
ABSTRACTThe problem of estimation of suspended load carried by a river is an important topic for many water resources projects. Conventional estimation methods are based on the assumption of exact observations. In practice, however, a major source of natural uncertainty is due to imprecise measurements and/or imprecise relationships between variables. In this paper, using the Multivariate Adaptive Regression Splines (MARS) technique, a novel fuzzy regression model for imprecise response and crisp explanatory variables is presented. The investigated fuzzy regression model is applied to forecast suspended load by discharge based on two real-world datasets. The accuracy of the proposed method is compared with two well-known parametric fuzzy regression models, namely, the fuzzy least-absolutes model and the fuzzy least-squares model. The comparison results reveal that the MARS-fuzzy regression model performs better than the other models in suspended load estimation for the particular datasets. This comparison is done based on four goodness-of-fit criteria: the criterion based on similarity measure, the criterion based on absolute errors and the two objective functions of the fuzzy least-absolutes model and the fuzzy least-squares model. The proposed model is general and can be used for modelling natural phenomena whose available observations are reported as imprecise rather than crisp.
Editor D. Koutsoyiannis; Associate editor H. Aksoy 相似文献
5.
Magneto‐rheological (MR) dampers are a promising device for seismic hazard mitigation because their damping characteristics can be varied adaptively using an appropriate control law. During the last few decades researchers have investigated the behavior of MR dampers and semi‐active control laws associated with these types of dampers for earthquake hazard mitigation. A majority of this research has involved small‐scale MR dampers. To investigate the dynamic behavior of a large‐scale MR damper, characterization tests were conducted at the Lehigh Network for Earthquake Engineering Simulation equipment site on large‐scale MR dampers. A new MR damper model, called the Maxwell Nonlinear Slider (MNS) model, is developed based on the characterization tests and is reported in this paper. The MNS model can independently describe the pre‐yield and post‐yield behavior of an MR damper, which makes it easy to identify the model parameters. The MNS model utilizes Hershel–Bulkley visco‐plasticity to describe the post‐yield non‐Newtonian fluid behavior, that is, shear thinning and thickening behavior, of the MR fluid that occurs in the dampers. The predicted response of a large‐scale damper from the MNS model along with that from existing Bouc–Wen and hyperbolic tangent models, are compared with measured response from various experiments. The comparisons show that the MNS model achieves better accuracy than the existing models in predicting damper response under cyclic loading. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
6.
Reinforced concrete columns with insufficient transverse reinforcement and non‐seismic reinforcement details are vulnerable to brittle shear failure and to loss of axial load carrying capacity in the event of a strong earthquake. In this paper, a procedure is presented after examining the application of two macro models for displacement‐based analysis of reinforced concrete columns subjected to lateral loads. In the proposed model, lateral load‐deformation response of the column is simulated by estimating flexural and shear deformation components separately while considering their interaction and then combining these together according to a set of rules depending upon column's yield, flexural and shear strengths. In addition, lateral deformation caused by reinforcement slip in beam–column joint regions and buckling of compression bars are taken into account and considered in the analysis. Implementation of the proposed procedure produces satisfactory lateral load–displacement relationships, which are comparable with experimental data. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
7.
Numerous non‐ductile reinforced concrete (RC) buildings with little or no shear reinforcement in beam‐column joints can be found in regions of moderate seismicity. To strengthen such substandard beam‐column joints, this study proposes a method in which RC wing walls are installed beside existing columns, which overcomes the lack of realistic strengthening methods for congested connections in RC buildings. The proposed strengthening mechanism improves the joint moment capacity by utilizing tension and compression acting on the beam–wing wall boundaries; thus, brittle joint hinging failure is prevented. Three 3/4‐scale RC exterior beam‐column joint specimens without shear reinforcement, two of which were strengthened by installing wing walls with different strengthening elements, were fabricated and tested. The test results verified the effectiveness of the proposed strengthening method and the applicability of this method to seismically substandard beam‐column joints. © 2017 The Authors. Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd. 相似文献
8.
The group method of data handling (GMDH) algorithm presented by A. C. Ivakhnenko and colleagues is an heuristic self‐organization method. It establishes the input–output relationship of a complex system using a multilayered perception‐type structure that is similar to a feed‐forward multilayer neural network. This study provides a step towards understanding and evaluating a role for GMDH in the investigation of the complex rainfall–runoff processes in a heterogeneous watershed in Taiwan. Two versions of the revised GMDH model are implemented: a stepwise regression procedure and a recursive formula. Eleven typhoon events in the Shen‐cei Creek watershed, Taiwan, are used to build the model and verify its usefulness. The prediction results of the revised GMDH models and the instantaneous unit hydrograph (IUH) model are compared. Based on the criteria of forecasting precision and the rate and time of peak error, a much better performance is obtained with the revised GMDH models. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
9.
Most of the available models of monolithic reinforced concrete joints under seismic action focus on estimation of cracking
and ultimate shear strengths. Very few studies have been directed towards developing expressions for the associated joint
deformations at the milestone response points so as to compose a limit-state model for joints that would be compatible with
the emerging framework of deformation based seismic assessment and design methods. This objective is pursued in the present
paper with particular emphasis on monolithic bridge joints. Deformation capacity at yielding and failure of joints is derived
by establishing equilibrium and geometric compatibility of smeared stresses and strains, and satisfying material constitutive
relationships. Expressions and model parameters are calibrated with the database of published bridge joint tests assembled
from International literature, using statistical evaluation. From the mean values of the design parameters simplified equations
for shear strength and ultimate shear strain of bridge joints are proposed. 相似文献
10.
The objective of this study is to investigate the effect of masonry infills on the seismic performance of low‐rise reinforced concrete (RC) frames with non‐seismic detailing. For this purpose, a 2‐bay 3‐storey masonry‐infilled RC frame was selected and a 1 : 5 scale model was constructed according to the Korean practice of non‐seismic detailing and the similitude law. Then, a series of earthquake simulation tests and a pushover test were performed on this model. When the results of these tests are compared with those in the case of the bare frame, it can be recognized that the masonry infills contribute to the large increase in the stiffness and strength of the global structure whereas they also accompany the increase of earthquake inertia forces. The failure mode of the masonry‐infilled frame was that of shear failure due to the bed‐joint sliding of the masonry infills while that of the bare frame appeared to be the soft‐storey plastic mechanism at the first storey. However, it is judged that the masonry infills can be beneficial to the seismic performance of the structure since the amount of the increase in strength appears to be greater than that in the induced earthquake inertia forces while the deformation capacity of the global structure remains almost the same regardless of the presence of the masonry infills. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
11.
Near‐fault ground motions impose large demands on structures compared to ‘ordinary’ ground motions. Recordings suggest that near‐fault ground motions with ‘forward’ directivity are characterized by a large pulse, which is mostly orientated perpendicular to the fault. This study is intended to provide quantitative knowledge on important response characteristics of elastic and inelastic frame structures subjected to near‐fault ground motions. Generic frame models are used to represent MDOF structures. Near‐fault ground motions are represented by equivalent pulses, which have a comparable effect on structural response, but whose characteristics are defined by a small number of parameters. The results demonstrate that structures with a period longer than the pulse period respond very differently from structures with a shorter period. For the former, early yielding occurs in higher stories but the high ductility demands migrate to the bottom stories as the ground motion becomes more severe. For the latter, the maximum demand always occurs in the bottom stories. Preliminary regression equations are proposed that relate the parameters of the equivalent pulse to magnitude and distance. The equivalent pulse concept is used to estimate the base shear strength required to limit story ductility demands to specific target values. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
12.
The seismic performance of existing structures can be assessed based on nonlinear static procedures, such as the Capacity Spectrum Method. This method essentially approximates peak responses of an inelastic single‐degree‐of‐freedom (SDOF) system using peak responses of an equivalent linear SDOF model. In this study, the equivalent linear models of inelastic SDOF systems are developed based on the constant strength approach, which does not require iteration for assessing the seismic performance of existing structures. To investigate the effects of earthquake type and seismic region on the equivalent linear models, four ground‐motion data sets—Japanese crustal/interface/inslab records and California crustal records—are compiled and used for nonlinear dynamic analysis. The analysis results indicate that: (1) the optimal equivalent linear model parameters (i.e. equivalent vibration period ratio and damping ratio) decrease with the natural vibration period, whereas they increase with the strength reduction factor; (2) the impacts of earthquake type and seismic region on the equivalent linear model parameters are not significant except for short vibration periods; and (3) the degradation and pinching effects affect the equivalent linear model parameters. We develop prediction equations for the optimal equivalent linear model parameters based on nonlinear least‐squares fitting, which improve and extend the current nonlinear static procedure for existing structures with degradation and pinching behavior. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
13.
Seismic performance of exterior beam–column subassemblages of reinforced concrete structure designed and detailed on the basis of the provisions of Eurocode and Indian Standards at different stages of their evolution is evaluated. Performance of the subassemblages designed and detailed according to the three different stages of codal evolution (gravity load design, ‘Nonductile’, and ‘Ductile’) is evaluated through analytical formulations and experimental investigations. In the ‘NonDuctile’ specimens, it has been observed that the shear distortion and degradation in stiffness and strength are significantly high. Performance of the ‘Ductile’ specimens based on Eurocode and Indian Standards is almost similar in terms of strength and stiffness degradation. Nevertheless, the specimen designed on the basis of Indian Standard shows higher energy dissipation at a given drift ratio. In the analytical study, shear and flexural failure of members of subassemblage and shear failure of the joint are considered as possible modes of failure of the beam–column subassemblage. For evaluating the shear strength of the joint region, a soften strut‐and‐tie model is used. Analytically obtained strengths based on the failure criteria of different components of the specimens have been first validated with experimental results and then used to determine the strength of the specimens. The investigation could indicate even the mode of failure at local level. It is utmost important to mention here that even the ductile specimens dissipate most of the energy through the development of damage in the joint region, which is neither desirable nor safe for the stability of whole structure. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
14.
15.
The inelastic (design) spectra characterizing a seismic hazard are generally obtained by the scaling‐down of the elastic (design) spectra via a set of response modification factors. The component of these factors, which accounts for the ductility demand ratio, is known as the strength reduction factor (SRF), and the variation of this factor with initial period of the oscillator is called an SRF spectrum. This study considers scaling of the SRF spectrum in the case of an elasto‐plastic oscillator with strength and stiffness degradation characteristics. Two models are considered: one depending directly on the characterization of source and site parameters and the other depending on the normalized design spectrum characterization of the seismic hazard. The first model is the same as that proposed earlier by the second author, and is given in terms of earthquake magnitude, strong‐motion duration, predominant period, geological site conditions, ductility demand ratio, and ductility supply‐related parameter. The second model is a new model proposed here in terms of the normalized pseudo‐spectral acceleration values (to unit peak ground acceleration), ductility demand ratio and ductility supply‐related parameter. For each of these models, least‐square estimates of the coefficients are obtained through regression analyses of the data for 956 recorded accelerograms in western U.S.A. Parametric studies carried out with the help of these models confirm the dependence of SRFs on strong‐motion duration and earthquake magnitude besides predominant period and site conditions. It is also seen that degradation characteristics make a slight difference for high ductility demands and may lead to lower values of SRFs, unless the oscillators are very flexible. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
16.
The feasibility and efficiency of a seismic retrofit solution for existing reinforced concrete frame systems, designed before the introduction of modern seismic‐oriented design codes in the mid 1970s, is conceptually presented and experimentally investigated. A diagonal metallic haunch system is introduced at the beam–column connections to protect the joint panel zone from extensive damage and brittle shear mechanisms, while inverting the hierarchy of strength within the beam–column subassemblies and forming a plastic hinge in the beam. A complete step‐by‐step design procedure is suggested for the proposed retrofit strategy to achieve the desired reversal of strength hierarchy. Analytical formulations of the internal force flow at the beam–column‐joint level are derived for the retrofitted joints. The study is particularly focused on exterior beam–column joints, since it is recognized that they are the most vulnerable, due to their lack of a reliable joint shear transfer mechanism. Results from an experimental program carried out to validate the concept and the design procedure are also presented. The program consisted of quasi‐static cyclic tests on four exterior, ? scaled, beam–column joint subassemblies, typical of pre‐1970 construction practice using plain round bars with end‐hooks, with limited joint transverse reinforcement and detailed without capacity design considerations. The first (control specimen) emulated the as‐built connection while the three others incorporated the proposed retrofitted configurations. The experimental results demonstrated the effectiveness of the proposed solution for upgrading non‐seismically designed RC frames and also confirmed the applicability of the proposed design procedure and of the analytical derivations. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
17.
Angus I. Best Lucy M. MacGregor Jeremy Sothcott Tim A. Minshull 《Geophysical Prospecting》2011,59(4):777-786
Improvements in the joint inversion of seismic and marine controlled source electromagnetic data sets will require better constrained models of the joint elastic‐electrical properties of reservoir rocks. Various effective medium models were compared to a novel laboratory data set of elastic velocity and electrical resistivity (obtained on 67 reservoir sandstone samples saturated with 35 g/l brine at a differential pressure of 8 MPa) with mixed results. Hence, we developed a new three‐phase effective medium model for sandstones with pore‐filling clay minerals based on the combined self‐consistent approximation and differential effective medium model. We found that using a critical porosity of 0.5 and an aspect ratio of 1 for all three components, the proposed model gave accurate model predictions of the observed magnitudes of P‐wave velocity and electrical resistivity and of the divergent trends of clean and clay‐rich sandstones at higher porosities. Using only a few well‐constrained input parameters, the new model offers a practical way to predict in situ porosity and clay content in brine saturated sandstones from co‐located P‐wave velocity and electrical resistivity data sets. 相似文献
18.
A. Benavent‐Climent 《地震工程与结构动力学》2007,36(8):1049-1064
This paper proposes a new model for quantifying the damage in structural steel components subjected to randomly applied flexural/shear stress reversals, such those induced by earthquakes. In contrast to existing approaches that consider the damage as a combination of the global amount of dissipated energy and maximum displacement, the proposed model represents the damage by two parameters: (a) the total dissipated energy and (b) the portion of the energy consumed in the skeleton part of the load–displacement curve. These parameters are employed to define a single ‘damage index’, which measures the level between 0 (no damage) and 1 (failure). The proposed model takes into account that the ultimate energy dissipation capacity of the steel component is path‐dependent and can change throughout the entire response duration. The new model is derived from low‐cycle fatigue static tests of round steel rods and steel plates subjected to bending and shear. The accuracy of the model is verified experimentally through dynamic real‐time shaking table tests. From these tests, it is observed that the proposed model measures the level of damage at any stage of the loading process reasonably well and predicts the failure of the structural component accurately. The model can be easily implemented in a computer program to assess the level of seismic damage and the closeness to failure in new structures or to evaluate the safety of existing ones. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
19.
Verification of system identification utilizing shaking table tests of a full‐scale 4‐story steel building 下载免费PDF全文
下载免费PDF全文 Yoshiki Ikeda 《地震工程与结构动力学》2016,45(4):543-562
This paper verifies the feasibility of the proposed system identification methods by utilizing shaking table tests of a full‐scale four‐story steel building at E‐Defense in Japan. The natural frequencies, damping ratios and modal shapes are evaluated by single‐input‐four‐output ARX models. These modal parameters are prepared to identify the mass, damping and stiffness matrices when the objective structure is modelled as a four degrees of freedom (4DOF) linear shear building in each horizontal direction. The nonlinearity in stiffness is expressed as a Bouc–Wen hysteretic system when it is modelled as a 4DOF nonlinear shear building. The identified hysteretic curves of all stories are compared to the corresponding experimental results. The simple damage detection is implemented using single‐input‐single‐output ARX models, which require only two measurements in each horizontal direction. The modal parameters are equivalent‐linearly evaluated by the recursive Least Squares Method with a forgetting factor. When the structure is damaged, its natural frequencies decrease, and the corresponding damping ratios increase. The fluctuation of the identified modal properties is the indirect information for damage detection of the structure. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
20.
This paper describes the results of shaking table tests to ascertain the ultimate behavior of slender base‐isolated buildings and proposes a time history response analysis method, which can predict the ultimate behavior of base‐isolated buildings caused by buckling fracture in laminated rubber bearings. In the tests, a base‐isolated structure model weighing 192 kN supported by four lead rubber bearings is used. The experimental parameters are the aspect ratio of height‐to‐distance between the bearings and the shape of and the axial stress on the bearings. The test results indicate that the motion types of the superstructure at large input levels can be classified into three types: the sinking type; the uplift type; and the mixed type. These behaviors depend on the relationship between the static ultimate lateral uplifting force on the superstructure and the lateral restoring characteristics of the base‐isolated story. In the analysis method, bearing characteristics are represented by a macroscopic mechanical model that is expanded by adding an axial spring to an existing model. Nonlinear spring characteristics are used for its rotational, shear, and axial spring. The central difference method is applied to solve the equation of motion. To verify the validity of the method, simulation analysis of the shaking table tests are carried out. The results of the analysis agree well with the test results. The proposed model can express the buckling behavior of bearings in the large deformation range. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献