首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Hydraulics of recirculating well pairs for ground water remediation   总被引：1，自引：0，他引：1  
Recirculating well pairs are a proven means of implementing bioremediation and may also be useful for applying other in situ ground water remediation technologies. A bromide tracer test was performed to characterize the hydraulic performance of a recirculating well pair installed at Moffett Field, California. In particular, we estimate two important properties of the recirculating well pair: (1) the fraction of captured water that is recycled between the wells, and (2) the travel-time distribution of ground water in the induced zone of recirculation. We also develop theoretical estimates of these two properties and demonstrate they depend upon a dimensionless pumping rate, denoted xi. The bromide breakthrough curve predicted from theory agrees well with that determined experimentally at Moffett Field. The minimum travel time between the wells is denoted t(min). In theory, t(min) depends inversely on Q, the pumping rate in the recirculating wells, and is proportional to a2, the square of the distance between the wells. Both the experimental and theoretical travel-time distributions indicate that at least half the recirculating water travels between the wells along fast flowpaths (travel time < 2*t(min)). Therefore, when designing recirculating well pairs, engineers should ensure that t(min) will be sufficiently high to allow biologically mediated reactions (or other in situ remediation processes) sufficient time to proceed.  相似文献   

2.
At a large industrial facility, methyl tert‐butyl ether (MTBE) was released to the subsurface and dispersed into the light, non‐aqueous phase liquids (LNAPL), in the first aquifer, with the LNAPL serving as a continuous source of MTBE in groundwater. Compound‐specific isotope analysis was conducted on both MTBE and tert‐butyl alcohol (TBA) in groundwater samples collected in 2008, 2011, and 2013 from wells located along and off the center line of the MTBE plume. The study demonstrated the onset and progress of biodegradation of MTBE between 2008 and 2013. The TBA observed in 2008 appears to be derived only in part from MTBE transformation while a significant portion of TBA might be contributed directly from LNAPL sources. In 2011 to 2013, the dominant source of TBA in the mid‐gradient plume was MTBE transformation. A contribution of an offsite LNAPL source, in particular to the down‐gradient area of the plume, is possible but could not be unequivocally confirmed. The time series provided direct evidence for MTBE biodegradation, but also a valuable insight on the sources of TBA.  相似文献   

3.
Propane biosparging and bioaugmentation were applied to promote in situ biodegradation of 1,4‐dioxane at Site 24, Vandenberg Air Force Base (VAFB), CA. Laboratory microcosm and enrichment culture testing demonstrated that although native propanotrophs appeared abundant in the shallow water‐bearing unit of the aquifer (8 to 23 ft below ground surface [bgs]), they were difficult to be enriched from a deeper water‐bearing unit (82 to 90 feet bgs). Bioaugmentation with the propanotroph Rhodococcus ruber ENV425, however, supported 1,4‐dioxane biodegradation in microcosms constructed with samples from the deep aquifer. For field testing, a propane‐biosparging system consisting of a single sparging well and four performance monitoring wells was constructed in the deep aquifer. 1,4‐dioxane biodegradation began immediately after bioaugmentation with R. ruber ENV425 (36 L; 4 × 109 cells/mL), and apparent first‐order decay rates for 1,4‐dioxane ranged from 0.021 day?1 to 0.036 day?1. First‐order propane consumption rates increased from 0.01 to 0.05 min?1 during treatment. 1,4‐dioxane concentrations in the sparging well and two of the performance monitoring wells were reduced from as high as 1090 µg/L to <2 µg/L, while 1,4‐dioxane concentration was reduced from 135 µg/L to 7.3 µg/L in a more distal third monitoring well. No 1,4‐dioxane degradation was observed in the intermediate aquifer control well even though propane and oxygen were present. The demonstration showed that propane biosparging and bioaugmentation can be used for in situ treatment of 1,4‐dioxane to regulatory levels.  相似文献   

4.
Although the anaerobic biodegradation of methyl tert‐butyl ether (MTBE) and tert‐butyl alcohol (TBA) has been documented in the laboratory and the field, knowledge of the microorganisms and mechanisms involved is still lacking. In this study, DNA‐stable isotope probing (SIP) was used to identify microorganisms involved in anaerobic fuel oxygenate biodegradation in a sulfate‐reducing MTBE and TBA plume. Microorganisms were collected in the field using Bio‐Sep® beads amended with 13C5‐MTBE, 13C1‐MTBE (only methoxy carbon labeled), or 13C4‐TBA. 13C‐DNA and 12C‐DNA extracted from the Bio‐Sep beads were cloned and 16S rRNA gene sequences were used to identify the indigenous microorganisms involved in degrading the methoxy group of MTBE and the tert‐butyl group of MTBE and TBA. Results indicated that microorganisms were actively degrading 13C‐labeled MTBE and TBA in situ and the 13C was incorporated into their DNA. Several sequences related to known MTBE‐ and TBA‐degraders in the Burkholderiales and the Sphingomonadales orders were detected in all three 13C clone libraries and were likely to be primary degraders at the site. Sequences related to sulfate‐reducing bacteria and iron‐reducers, such as Geobacter and Geothrix, were only detected in the clone libraries where MTBE and TBA were fully labeled with 13C, suggesting that they were involved in processing carbon from the tert‐butyl group. Sequences similar to the Pseudomonas genus predominated in the clone library where only the methoxy carbon of MTBE was labeled with 13C. It is likely that members of this genus were secondary degraders cross‐feeding on 13C‐labeled metabolites such as acetate.  相似文献   

5.
Petroleum hydrocarbon vapors biodegrade aerobically in the subsurface. Depth profiles of petroleum hydrocarbon vapor and oxygen concentrations from seven locations in sandy and clay soils across four states of Australia are summarized. The data are evaluated to support a simple model of biodegradation that can be used to assess hydrocarbon vapors migrating toward built environments. Multilevel samplers and probes that allow near‐continuous monitoring of oxygen and total volatile organic compounds (VOCs) were used to determine concentration depth profiles and changes over time. Collation of all data across all sites showed distinct separation of oxygen from hydrocarbon vapors, and that most oxygen and hydrocarbon concentration profiles were linear or near linear with depth. The low detection limit on the oxygen probe data and because it is an in situ measurement strengthened the case that little or no overlapping of oxygen and hydrocarbon vapor concentration profiles occurred, and that indeed oxygen and hydrocarbon vapors were largely only coincident near the location where they both decreased to zero. First‐order biodegradation rates determined from all depth profiles were generally lower than other published rates. With lower biodegradation rates, the overlapping of depth profiles might be expected, and yet such overlapping was not observed. A model of rapid (instantaneous) reaction of oxygen and hydrocarbon vapors compared to diffusive transport processes is shown to explain the important aspects of the 13 depth profiles. The model is simply based on the ratio of diffusion coefficients of oxygen and hydrocarbon vapors, the ratio of the maximum concentrations of oxygen and hydrocarbon vapors, the depth to the maximum hydrocarbon source concentration, and the stoichiometry coefficient. Whilst simple, the model offers the potential to incorporate aerobic biodegradation into an oxygen‐limited flux‐reduction approach for vapor intrusion assessments of petroleum hydrocarbon compounds.  相似文献   

6.
Mineralization of 14C‐radiolabled vinyl chloride ([1,2‐14C] VC) and cis‐dichloroethene ([1,2‐14C] cis‐DCE) under hypoxic (initial dissolved oxygen (DO) concentrations about 0.1 mg/L) and nominally anoxic (DO minimum detection limit = 0.01 mg/L) was examined in chloroethene‐exposed sediments from two groundwater and two surface water sites. The results show significant VC and dichloroethene (DCE) mineralization under hypoxic conditions. All the sample treatments exhibited pseudo‐first‐order kinetics for DCE and VC mineralization over an extended range of substrate concentrations. First‐order rates for VC mineralization were approximately 1 to 2 orders of magnitude higher in hypoxic groundwater sediment treatments and at least three times higher in hypoxic surface water sediment treatments than in the respective anoxic treatments. For VC, oxygen‐linked processes accounted for 65 to 85% of mineralization at DO concentrations below 0.1 mg/L, and 14CO2 was the only degradation product observed in VC treatments under hypoxic conditions. Because the lower detection limit for DO concentrations measured in the field is typically 0.1 to 0.5 mg/L, these results indicate that oxygen‐linked VC and DCE biodegradation can be significant under field conditions that appear anoxic. Furthermore, because rates of VC mineralization exceeded rates of DCE mineralization under hypoxic conditions, DCE accumulation without concomitant accumulation of VC may not be evidence of a DCE degradative “stall” in chloroethene plumes. Significantly, mineralization of VC above the level that could reasonably be attributed to residual DO contamination was also observed in several nominally anoxic (DO minimum detection limit = 0.01 mg/L) microcosm treatments.  相似文献   

7.
This research demonstrates that groundwater contaminated by a relatively dilute but persistent concentration of 1,4‐dioxane (1,4‐D), approximately 60 μg/L, and chlorinated aliphatic co‐contaminants (1.4 to 10 μg/L) can be efficiently and reliably treated by in situ aerobic cometabolic biodegradation (ACB). A field trial lasting 265 days was conducted at Operable Unit D at the former McClellan Air Force Base and involved establishing an in situ ACB reactor through amending recirculated groundwater with propane and oxygen. The stimulated indigenous microbial population was able to consistently degrade 1,4‐D to below 3 μg/L while the co‐contaminants trichloroethene (TCE) and 1,2‐dichloroethane (1,2‐DCA) were decreased to below 1 μg/L and 0.18 μg/L, respectively. A stable treatment efficiency of more than 95% removal for 1,4‐D and 1,2‐DCA and of more than 90% removal for TCE was achieved. High treatment efficiencies for 1,4‐D and all co‐contaminants were sustained even without propane and oxygen addition for a 2‐week period.  相似文献   

8.
Enhanced subsurface biorestoration is rapidly becoming recognized as a valuable tool for the restoration of hydrocarbon-contaminated aquifers and sediments. Previous field and laboratory studies at a former wood creosoting facility near Conroe, Texas, have indicated that insufficient oxygen is the primary factor limiting the biotransformation of polynuclear aromatics (PNAs) in sediments and ground water at this site. A series of laboratory experiments and field push-pull injection tests were performed as part of this project to: (1) study the effect of low oxygen concentrations on the biotransformation of PNAs; (2) identify the minimum concentration of PNAs that could be achieved through the addition of oxygen alone; (3) confirm that enhanced subsurface biorestoration is feasible at this site; and (4) test an existing numerical model of the biotransformation process (BIOPLUME). The laboratory studies demonstrated that biotransformation of the PNAs was not inhibited at dissolved oxygen concentrations as low as 0.7 mg/L although this work did suggest that there may be a minimum PNA concentration of 30 to 70 μg/L total PNAs below which biotransformation was inhibited. The field push-pull tests confirmed that addition of oxygen was effective in enhancing the subsurface biodegradation of the PNAs. The minimum concentration achieved using oxygen alone was approximately 60 μg/L total PNAs. Minimal biotransformation of these compounds was observed without oxygen addition. The numerical model BIOPLUME was tested against monitoring data from the field experiments and appears to provide a good approximation of the biodegradation process.  相似文献   

9.
Stream–subsurface exchange plays a significant role in the fate and transport of contaminants in streams. It has been modelled explicitly by considering fundamental processes such as hydraulic exchange, colloid filtration, and contaminant interactions with streambed sediments and colloids. The models have been successfully applied to simulate the transport of inorganic metals and nutrients. In this study, laboratory experiments were conducted in a recirculating flume to investigate the exchange of a hydrophobic organic contaminant, p,p′‐dichloro‐diphenyl‐dichloroethane (DDE), between a stream and a quartz sand bed. A previously developed process‐based multiphase exchange model was modified by accounting for the p,p′‐DDE kinetic adsorption to and desorption from the bed sediments/colloids and was applied to interpret the experimental results. Model input parameters were obtained by conducting independent small‐scale batch experiments. Results indicate that the immobilization of p,p′‐DDE in the quartz sand bed can occur under representative natural stream conditions. The observed p,p′‐DDE exchange was successfully simulated by the process‐based model. The model sensitivity analysis results show that the exchange of p,p′‐DDE can be sensitive to either the sediment sorption/desorption parameters or colloidal parameters depending on the experimental conditions tested. For the experimental conditions employed here, the effect of colloids on contaminant transport is expected to be minimal, and the stream–subsurface exchange of p,p′‐DDE is dominated by the interaction of p,p′‐DDE with bed sediment. The work presented here contributes to a better mechanistic understanding of the complex transport process that hydrophobic organic contaminants undergo in natural streams and to the development of reliable, predictive models for the assessment of impacted streams. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

10.
A detailed seasonal study of soil vapor intrusion at a cold climate site with average yearly temperature of 1.9 °C was conducted at a house with a crawlspace that overlay a shallow dissolved‐phase petroleum hydrocarbon (gasoline) plume in North Battleford, Saskatchewan, Canada. This research was conducted primarily to assess if winter conditions, including snow/frost cover, and cold soil temperatures, influence aerobic biodegradation of petroleum vapors in soil and the potential for vapor intrusion. Continuous time‐series data for oxygen, pressure differentials, soil temperature, soil moisture, and weather conditions were collected from a high‐resolution monitoring network. Seasonal monitoring of groundwater, soil vapor, crawlspace air, and indoor air was also undertaken. Petroleum hydrocarbon vapor attenuation and biodegradation rates were not significantly reduced during low temperature winter months and there was no evidence for a significant capping effect of snow or frost cover that would limit oxygen ingress from the atmosphere. In the residual light nonaqueous phase liquid (LNAPL) source area adjacent to the house, evidence for biodegradation included rapid attenuation of hydrocarbon vapor concentrations over a vertical interval of approximately 0.9 m, and a corresponding decrease in oxygen to less than 1.5% v/v. In comparison, hydrocarbon vapor concentrations above the dissolved plume and below the house were much lower and decreased sharply within a few tens of centimeters above the groundwater source. Corresponding oxygen concentrations in soil gas were at least 10% v/v. A reactive transport model (MIN3P‐DUSTY) was initially calibrated to data from vertical profiles at the site to obtain biodegradation rates, and then used to simulate the observed soil vapor distribution. The calibrated model indicated that soil vapor transport was dominated by diffusion and aerobic biodegradation, and that crawlspace pressures and soil gas advection had little influence on soil vapor concentrations.  相似文献   

11.
Oxygen probes developed to measure in situ oxygen concentrations in gaseous and aqueous environments were evaluated in laboratory tests and during long-term field evaluation trials at contaminated sites. The oxygen probes were shown to have a linear calibration and to be accurate compared to conventional dissolved oxygen electrodes and gas chromatography, both of which require labor-intensive sample collection and processing. The probes, once calibrated, required no maintenance or recalibration for up to a period of 7 years in low-oxygen environments, demonstrating long-term stability. Times to achieve 90% of the stabilized concentration ( t 90) after a step change in aqueous oxygen concentration were 100–120 min in laboratory experiments and up to 180 min in field experiments, which is adequate for monitoring subsurface changes. Field application data demonstrated that the oxygen probes could monitor oxygen concentrations in hydrocarbon-contaminated ground water to a depth of 20 m below the water table or in pyritic vadose zones over extended periods. During bioremediation field trials, oxygen monitoring enabled estimation of oxygen utilization rates by microorganisms and hydrocarbon biodegradation rates. Also, probes were able to monitor the development of ground water desaturation during air sparging trials, enabling the automated assessment of the distribution of injected air.  相似文献   

12.
The non‐aqueous phase liquid simulator was used to model and interpret the occurrence of a thin benzene‐contaminated soil layer 9.0 m below the groundwater table in an abandoned gas plant site. The simulator was first evaluated in column tests under similar conditions to the contaminated site. Saturation–capillary pressure (S–P) relationships were extended from the laboratory scale of the column tests to the field scale of the subsurface at the abandoned site. Dynamic boundary conditions were established in order to prevent the model from generating excessive vertical velocities. The modelled benzene layer formation process agreed well with the in situ observations. With falling and then rising of the water table, benzene release from the surface migrated downward and then upward and distributed itself below and above the water table. Biochemical degradation of benzene made the distribution discontinuous in the subsurface. These two factors resulted in the thin benzene‐contaminated layer below the groundwater table. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

13.
Microencapsulation of degradative organisms enhances microorganism survivability (Stormo and Crawford 1994). The use of encapsulated cell microbeads for in situ biodegradation depends not only on microorganism survival but also on microbead transport characteristics. Two forced-gradient, recirculating-loop tracer experiments were conducted to evaluate the feasibility of encapsulated cell transport and bioremediation on the basis of polystyrene microsphere transport results. The tracer tests were conducted in a shallow, confined, unconsolidated, heterogeneous, sedimentary aquifer using bromide ion and 2 μm, 5 μn, and 15 μm microsphere tracers. Significant differences were observed in the transport of bromide solute and polystyrene microspheres. Microspheres reached peak concentrations in monitoring wells before bromide, which was thought to reflect the influence of aquifer heterogeneity. Greater decreases in microsphere C/Co ratios were observed with distance from the injection wells than in bromide C/Co ratios, which was attributed to particle filtration and/or settling. Several methods might be considered for introducing encapsulated cell microbeads into a subsurface environment, including direct injection into a contaminated aquifer zone, injection through a recirculating ground water flow system, or emplacement in a subsurface microbial curtain in advance of a plume. However, the in situ use of encapsulated cells in an aquifer is probably limited to aquifers containing sufficiently large pore spaces, allowing passage of at least some encapsulated cells. The use of encapsulated cells may also be limited by differences in solute and microbead transport patterns and flowpath clogging by larger encapsulated cell microbeads.  相似文献   

14.
In situ bioreclamation is a proven technology that cost-effectively treats organic contamination in subsurface environments. As a remediation strategy, it reduces both the contamination dissolved in ground water, as well as residual soil-bound contamination.
To maximize biodegradation, the technology is applied after conducting laboratory studies. Application of the technology involves infiltrating necessary nutrients to the contaminated subsurface.
Results of a specific case study indicate excellent performance with rapid cleanup of petroleum hydrocarbon contamination from soils and ground water.
Costs associated with in situ bioreclamation technology showed a savings of approximately 50 percent over simple pump-and-treat technology. Time frame for cleanup was shown to be approximately 30 percent of the projected time frame of simple pump-and-treat technology.  相似文献   

15.
Benzene, toluene, ethylbenzene, and xylene (BTEX) hydrocarbons are typically the most abundant carbon source for bacteria in gasoline-contaminated ground water. In situ bioremediation strategies often involve stimulating bacterial heterotrophic production in an attempt to increase carbon demand of the assemblage. This may, in turn, stimulate biodegradation of contaminant hydrocarbons. In this study, ground water circulation wells (GCWs) were used as an in situ treatment for a fuel-contaminated aquifer to stimulate bacterial production, purportedly by increasing oxygen transfer to the subsurface, circulating limiting nutrients, enhancing bioavailability of hydrocarbons, or by removing metabolically inhibitory volatile organics. Bacterial production, as measured by rates of bacterial protein synthesis, was stimulated across the zone of influence (ZOI) of a series of GCWs. Productivity increased from ∼102 to >105 ng C/L hour across the ZOI, suggesting that treatment stimulated overall biodegradation of carbon sources present in the ground water. However, even if BTEX carbon met all bacterial carbon demand, biodegradation would account for <4.3% of the total estimated BTEX removed from the ground water. Although bacterial productivity measurements alone cannot prove the effectiveness of in situ bioremediation, they can estimate the maximum amount of contaminant that may be biodegraded by a treatment system.  相似文献   

16.
Natural Attenuation of Aromatic Hydrocarbons in a Shallow Sand Aquifer   总被引：8，自引：0，他引：8  
Inadvertent release of petroleum products such as gasoline into the subsurface can initiate ground water contamination, particularly by the toxic, water-soluble and mobile gasoline components: benzene, toluene and xylenes (BTX). This study was undertaken to examine the processes controlling the rate of movement and the persistence of dissolved BTX in ground water in a shallow, unconfined sand aquifer.
Water containing about 7.6 mg/ L total BTX was introduced below the water table and the migration of contaminants through a sandy aquifer was monitored using a dense sampling network. BTX components migrated slightly slower than the ground water due to sorptive retardation. Essentially all the injected mass of BTX was lost within 434 days due to biodegradation. Rates of mass loss were similar for all monoaromatics; benzene was the only component to persist beyond 270 days. Laboratory biodegradation experiments produced similar rates, even when the initial BTX concentration varied.
A dominant control over BTX biodegradation was the availability of dissolved oxygen. BTX persisted at the field site in layers low in dissolved oxygen. Decreasing mass loss rates over time observed in the field experiment are not likely due to first-order deeradation rates, but rather to the persistence of small fractions of BTX mass in anoxic layers.  相似文献   

17.
Successful in situ groundwater remediation relies on the adequate distribution of treatment materials within the subsurface. Zero‐valent iron (ZVI) is widely used for the remediation of soils contaminated with chlorinated organic compounds. Because ZVI is a solid, various techniques are used to distribute ZVI in the subsurface; however, a major uncertainty in this process involves determining the distribution of the iron during emplacement. A method of mapping the distribution of ferromagnetic material such as ZVI is by magnetic susceptibility (MS), a novel approach that is highly sensitive, quantitative, objective, and easily applied in field. The method has been tested in the laboratory on synthetic cores containing EHC®, an organic amendment containing 40 to 50% ZVI, using an MS meter with two types of sensors (loop and handheld). Both sensors have high sensitivity (e.g., 1% disseminated EHC is easily detected), whereas the hand‐held sensor has greater spatial resolution (e.g., differences are notable on a scale of 1 cm). Following the laboratory studies, the handheld instrument was used to perform field measurements for multiple pilot studies and a full‐scale application of EHC using various delivery methods (pneumatic fracturing, hydraulic fracturing, and direct injection) to construct a biobarrier at a field remedial site. The MS method has proven invaluable in quantifying amendment distribution and ensuring appropriate application of this remedial technology.  相似文献   

18.
The occurrence of aerobic biodegradation in the vadose zone between a subsurface source and a building foundation can all-but eliminate the risks from methane and petroleum vapor intrusion (PVI). Understanding oxygen availability and the factors that affect it (e.g., building sizes and their distribution) are therefore critical. Uncovered ground surfaces allow oxygen access to the subsurface to actively biodegrade hydrocarbons (inclusive of methane). Buildings can reduce the net flux of oxygen into the subsurface and so reduce degradation rates. Here we determine when PVI and methane risk is negligible and/or extinguished; defined by when oxygen is present across the entire sub-slab region of existing or planned slab-on-ground buildings. We consider all building slab sizes, all depths to vapor sources and the effect of spacings between buildings on the availability of oxygen in the subsurface. The latter becomes critical where buildings are in close proximity or when increased building density is planned. Conservative assumptions enable simple, rapid and confident screening should sites and building designs comply to model assumptions. We do not model the aboveground “building” processes (e.g., air exchange), and assume the slab-on-ground seals the ground surface so that biodegradation of hydrocarbons is minimized under the built structure (i.e., the assessment remains conservative). Two graphs represent the entirety of the outcomes that allow simple screening of hydrocarbon vapors based only on the depth to the source of vapors below ground, the concentration of vapors within the source, the width of the slab-on-ground building, and the gap between buildings; all independent of soil type. Rectangular, square, and circular buildings are considered. Comparison with field sites and example applications are provided, along with a simple 8-step screening guide set in the context of existing guidance on PVI assessment.  相似文献   

19.
  相似文献   

20.
Song‐Bae Kim 《水文研究》2005,19(20):4069-4079
  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号