共查询到20条相似文献，搜索用时 15 毫秒
1.
Strain accumulation in sand due to cyclic loading: Drained cyclic tests with triaxial extension 总被引：1，自引：0，他引：1
T. Wichtmann A. Niemunis Th. Triantafyllidis 《Soil Dynamics and Earthquake Engineering》2007,27(1):42-48
This paper presents results of numerous drained cyclic tests with triaxial extension. The influence of the strain amplitude, the average stress and the number of load cycles on the accumulation rate was studied. A simple cyclic flow rule was observed. Most findings confirm a previous study with cyclic triaxial compression tests. The test results serve as the basis of an explicit accumulation model. 相似文献
2.
Subgrade soils of traffic infrastructures are subjected to large numbers of load applications at a stress level below their shear strength. It is therefore of great practical relevance to study the deformation behavior of soft clay under long-term cyclic loading. In this study, a series of monotonic triaxial tests and long-term cyclic (50,000 cycles) triaxial tests have been carried out to investigate the undrained deformation behavior of undisturbed soft clay from Wenzhou, China. The stress–strain hysteretic loop, resilient modulus and permanent strain of the tested samples were found significantly dependent on CSR and confining pressure. With an increase of CSR and confining pressure, the resilient modulus decreases more significantly with increasing number of cycles and the accumulation rate of permanent strain increases. Furthermore, the shape of the stress–strain hysteretic loop almost remains unchanged and the resilient modulus tends to a steady value after a large number of cycles. Based on the experimental results, two equations are established for the prediction of long-term resilient modulus and permanent strain. Finally, a new critical value of 0.65 is suggested for CSR. When CSR>0.65, the resilient modulus for large number of cycles is reduced to a so called “asymptotic stiffness” and the accumulation rate of permanent strain significantly increases. 相似文献
3.
Initial fabric of a soil induced by its cyclic strain history is an important parameter together with the void ratio, state of stress and amplitude in respect to further accumulation of deformations under drained cyclic loading. It is of importance for the further deformation prediction to determine the initial fabric of the grain skeleton or the cyclic loading history of the soil. An attempt is made within this paper to correlate small strain stiffness of non-cohesive soil with its cyclic loading history. The results of performed cyclic and dynamic torsional tests show that small strain shear modulus is only moderately affected by cyclic prestraining even if high amplitudes are applied. A signature of prestraining history is observed in the tests since the sand memorizes its prestraining amplitude and the number of applied cycles. 相似文献
4.
T. Wichtmann A. Niemunis Th. Triantafyllidis 《Soil Dynamics and Earthquake Engineering》2007,27(1):14-28
This paper presents results of cyclic triaxial (CT) tests on sand with a simultaneous variation of the axial and the lateral stresses. Furthermore, a cyclic multidimensional simple shear (CMDSS) device and corresponding test results are discussed. For in-phase cycles with a constant strain amplitude it is demonstrated that the accumulation rate is independent of the polarization of the cycles in the strain space. Polarization changes lead to a temporary increase of the accumulation rate: they increase the effectiveness of compaction. For out-of-phase (e.g. elliptical) cycles the shape of the strain loop significantly influences the residual strain. A circular strain loop generates twice larger accumulation rates than a one-dimensional strain loop with identical span. The accumulation rate is not influenced by the circulation of the strain loop. It is shown that the direction of accumulation (so-called “cyclic flow rule”) is only moderately affected by the polarization and the shape of the cycles. 相似文献
5.
通过GDS动三轴设备对赣南红黏土进行了一系列排水条件下的大次数循环试验,研究不同循环应力比、固结应力比及围压对赣南红黏土累积变形特性的影响。结果表明：在不同固结应力比、固结压力和循环应力比条件下,红黏土的累积应变都呈现出先迅速累积,后增长变缓,最终稳定的趋势;在一定的循环次数之后,不同初始固结应力和不同初始应力比条件下累积应变与循环次数之间的变形规律呈现为线性关系,且初始固结应力和初始固结应力比越小,其线性相关性越好;不同循环应力比下赣南红黏土的平均累积应变速率与循环次数之间也呈现出明显的线性关系。此外,基于以上关系建立了赣南红黏土在长期循环荷载作用下的累积变形预测模型,并通过对比验证了该模型的可行性。 相似文献
6.
Initial fabric of a soil induced by its cyclic strain history is an important parameter among others like void ratio, state of stress and amplitude concerning the further accumulation of deformations under cyclic loading. It is of high importance to determine methods in order to estimate the initial fabric of the grain skeleton or the cyclic loading history of the soil. An attempt is made in this paper to correlate small strain stiffness of non-cohesive soil with its cyclic loading history. For this purpose several cyclic triaxial tests with specimens subjected to cyclic axial loading were performed and changes of small strain soil properties due to this cyclic loading were studied. All these tests showed only moderate changes of small strain stiffnesses independently of the different boundary conditions. Thus, a correlation between fabric or strain history and small strain stiffnesses seems not to be possible. 相似文献
7.
A constitutive model of rocks subjected to cyclic stress–temperature was proposed. Based on statistical damage theory, the damage constitutive model with Weibull distribution was extended. Influence of model parameters on the stress–strain curve for rock reloading after stress–temperature cycling was then discussed. The proposed model was initially validated by rock tests for cyclic stress–temperature and only cyclic stress. Finally, the total damage evolution induced by stress–temperature cycling and reloading after cycling was explored and discussed. The proposed constitutive model is reasonable and applicable, describing well the stress–strain relationship during stress–temperature cycles and providing a good fit to the test results. Elastic modulus in the reference state and the damage induced by cycling affect the shape of reloading stress–strain curve. Total damage induced by cycling and reloading after cycling exhibits three stages: initial slow increase, mid-term accelerated increase, and final slow increase. 相似文献
8.
To investigate the coupling effects of cyclic deviator stress and cyclic confining pressure on the deformation behavior of natural soft clay under partially-drained conditions, a series of one-way cyclic triaxial tests with and without cyclic confining pressure were carried out. Test results show that, at the same amplitude of cyclic deviator stress, the increase of cyclic confining pressure amplitude will accelerate the accumulation of both permanent volumetric and axial strain significantly. The comparison between test results for different amplitudes of cyclic confining pressure shows that tests with a cyclic confining pressure corresponding to a stress path of ηampl=pampl/qampl=1 lead to a 1.4 times larger permanent volumetric strain and a 1.2 times larger permanent axial strain compared to the conventional cyclic triaxial tests with constant confining pressure (ηampl=1/3). In case of ηampl=2 the permanent strains are found to be even 2.0 or 1.5 times larger compared to the standard tests. Finally, an empirical formula is proposed for the prediction of permanent axial deformations of natural soft clays under partially-drained conditions, considering the effects of cyclic confining pressure. 相似文献
9.
以片状颗粒成分为主的片状结构砂与常用的圆形颗粒标准石英砂相比,在物理力学特性上有显著的差异。循环荷载作用下,饱和砂土振动孔压上升会导致土体刚度发生软化,当振动孔压累积达到一定水平时,会产生液化现象,从而引起土体结构发生破坏。采用英国WFI动三轴仪,研究了南京片状细砂在循环荷载作用下,静偏应力水平、循环应力比水平和循环次数对其动应力一应变关系的影响,考虑每一次循环过程中动应力—应变关系滞回曲线的卸载及再加载割线动剪切模量Gsec和最大割线模量Gmax的变化特性,建立了动剪模量软化的经验公式;静偏应力水平对动剪模量软化有显著影响,随着循环次数的增加,动应力—应变滞回圈逐渐向应变累积方向滑移和向应变轴方向倾斜,且彼此分离;考虑循环软化特性,采用修正的Masing准则,描述了循环荷载下南京片状细砂的动应力—应变关系。 相似文献
10.
A laboratory study on the undrained dynamic behavior of saturated clays in cyclic triaxial tests with a variable confining pressure (VCP tests) is presented. Tests were performed on remolded clayey samples using a dynamic triaxial device where the deviatoric stress and confining pressure can be varied simultaneously. Various cyclic stress paths have been applied on the specimens through varying the ratios or phase differences between the cyclic deviatoric stress and cyclic confining pressure. Specifically, the stress paths used in the present study were designed to simulate the coupling effects of simultaneously varying shear and normal stresses in clays due to earthquakes and other vibration sources. Test results obtained from this study show that the undrained response of saturated clays is strongly influenced by the variation of confining pressure, in terms of pore water pressure, development speed of cyclic strain and magnitude of cyclic strength. It is found that when strong P-waves are propagating in soil layers, VCP tests are more appropriate for the simulation of in situ stress fields than the conventional cyclic triaxial tests with a constant confining pressure (CCP tests). 相似文献
11.
12.
13.
Settlements under consecutive series of cyclic loading 总被引：1，自引：0，他引：1
Hüseyin Y&#x;ld&#x;r&#x;m Hayreddin Eran 《Soil Dynamics and Earthquake Engineering》2007,27(6):577-585
In this study, consolidation settlements of soft clay caused by cyclic loading and the affecting factors such as number of cycles and stress level were experimentally investigated. A group of samples prepared in slurry consolidometer in the laboratory were tested using cyclic simple shear testing device. Normally consolidated samples were subjected to five consecutive series of cyclic loading and drainage for 60 min were applied between each cyclic loading stages. Cyclic tests were performed with stress controlled two-way sinusoidal wave loading with different stress levels and number of cycles. Frequency of cyclic loading was constant as 0.1 Hz. As a result of this study, it can be concluded that soft clays subjected to undrained cyclic loading and drainage cycles exhibit more resistance against subsequent cyclic shear stresses. The consolidation settlements, pore pressures and shear strains decrease after each stage of cyclic loading. 相似文献
14.
Repeated small amplitude dynamic loading of the soil in the vicinity of buildings, as arising from traffic or construction activities, may cause differential foundation settlements and structural damage. In this paper, an accumulation model for settlements due to vibrations at small strain levels in granular non-cohesive soils is proposed. It is assumed that the dynamic part of the stresses is small with respect to the static part. As plastic deformation in the soil is only observed after a considerable amount of dynamic loading cycles, only the accumulation of the average plastic deformation is considered. The model accounts for the dependency of the deformation on the stress state, the void ratio, and the dynamic loading amplitude. The model is calibrated for homogeneous fine grained sands with the aid of cyclic triaxial test results. 相似文献
15.
波浪荷载能引起海床土体的主应力轴连续旋转。不同于地震、交通等循环荷载,在周期性波浪荷载作用的土体应力路径方式下,软黏土的软化效用更为明显。本文分别对天然和扰动的海床土体在波浪荷载作用下的应力响应进行模拟,并分析应力路径的特点;为描述软化后的应力-应变关系,将软化效用和累积塑性应变的参数引入到能够反应土体动力非线性的Hardin-Drnevich模型中,建立修正模型,使之能够反应软黏土体软化与塑性应变累计特性;通过与模拟波浪荷载下土体应力特征的循环耦合试验结果进行对比分析,验证该修正模型的可靠性。 相似文献
16.
Influence of colloidal silica grout on liquefaction potential and cyclic undrained behavior of loose sand 总被引：4，自引：0，他引：4
Patricia M. Gallagher James K. Mitchell 《Soil Dynamics and Earthquake Engineering》2002,22(9-12):1017-1026
Cyclic triaxial tests were performed to investigate the influence of colloidal silica grout on the deformation properties of saturated loose sand. Distinctly different deformation properties were observed between grouted and ungrouted samples. Untreated samples developed very little axial strain prior to the onset of liquefaction. However, once liquefaction was triggered, large strains occurred rapidly and the samples collapsed within a few additional loading cycles. In contrast, grouted sand samples experienced very little strain during cyclic loading. Additionally, the strain accumulated uniformly throughout loading rather than rapidly prior to collapse and the samples never collapsed. Cyclic triaxial tests were done on samples stabilized with colloidal silica at concentrations of 5, 10, 15, and 20%. In general, samples stabilized with higher concentrations of colloidal silica experienced very little strain during cyclic loading. Sands stabilized with lower concentrations tolerated cyclic loading well, but experienced slightly more strain. Thus, treatment with colloidal silica grout significantly increased the deformation resistance of loose sand to cyclic loading. 相似文献
17.
Laboratory cyclic triaxial tests were performed to investigate the effect of fine content on the pore pressure generation in sand. Strain-controlled, consolidated undrained tests have been performed with a cyclic shear strain range of 0·015-1·5%. These tests were carried to 1000 cycles or to initial liquefaction, which ever occurred first. Triaxial tests were performed on pure sand silt specimens and specimens with silt additions of 10, 20, 30, and 60% by weight. Two types of silt, a non-plastic silt and a low plasticity silt (PI 10) were used as control materials. The main parameters varied in this study were the amount of silt, the plasticity index of silt, and the void ratio where the observed parameter was the pore pressure generation. For all silt contents, silt plasticity and the number of loading cycles have no significant effect at strain levels below 0·01%. Therefore, threshold strain for silty sands have approximately the same value as sands. For both non-plastic and low plasticity silts, there is a significant increase in the generated pore pressure at high strain levels. 相似文献
18.
针对人工制备的大连饱和黏土,在静应力与循环应力联合作用下进行了多组循环剪切试验,着重探讨了初始静力大小及加载速率对循环剪切变形特性的影响.试验表明静应力与循环应力作用下饱和黏土具有循环蠕变特性,总应变由初始静应变和循环蠕变两部分组成,其中循环蠕变主要受循环应力幅值、初始静应力大小及其加载速率的影响,循环蠕变的逐次增加量... 相似文献
19.
Masayuki Hyodo Noritaka Aramaki Masayuki Itoh Adrian F.L. Hyde 《Soil Dynamics and Earthquake Engineering》1996,15(5):331-336
Cyclic triaxial tests have been carried out on a skeletal carbonate sand from the west coast of Eire. Results are presented for undrained cyclic shear tests on samples with 80% of relative density consolidated under both isotropic and anisotropic conditions. Failure was defined as a 5% double amplitude cyclic strain and a 5% peak axial strain for stress-reversal and non-reversal stress conditions, respectively. Using this definition the cyclic strength for isotropically consolidated samples was affected by the confining pressure although the angular platey nature of the sand resulted in higher cyclic strengths than for a comparable silica sand. For anisotropically consolidated samples the cyclic strength increased with increasing initial static shear stress while on the other hand the cyclic strength normalised in the usual way with respect to the initial confining pressure decreased as this pressure increased. 相似文献