共查询到20条相似文献，搜索用时 265 毫秒
1.
天然沉积砂土力学特性受各向异性及结构性影响明显,实际工程中不能忽视。为探究二者的影响,首先在二维离散元程序NS2D中采用椭圆颗粒模拟了重力场中颗粒长轴主方向为水平的各向异性净砂样,随后基于结构性砂土胶结厚度分布规律及室内试验提出了一个新的微观胶结接触模型并将其引入各向异性净砂样以模拟天然各向异性结构性砂土,最后对该离散元试样进行了双轴试验模拟,将模拟结果与室内试验结果对比以验证该模型的适用性,并对其微观力学特性变化进行研 究。分析结果表明,随着剪切进行,各向异性结构性砂土呈明显应变软化及剪胀现象;胶结接触逐渐减少,且主方向始终为竖向方向;胶结破坏速率及胶结破坏率变化情况与宏观力学响应较一致,且胶结物多为拉剪破坏;土颗粒排列主方向始终为水平向,且水平向排列颗粒所占比例略微增大。 相似文献
2.
Rui Chen Xiaobin Ding Lianyang Zhang Yongli Xie Hongpeng Lai 《Environmental Earth Sciences》2017,76(22):772
This paper presents a series of numerical simulations using discrete element method (DEM) to study the behavior of biopolymer-stabilized mine tailings (MT). Validation is conducted by comparing the DEM results with the experimental data. The macro-behavior comparison shows that the DEM simulations are in good agreement with experimental results. Analysis of the micro-parameters indicates more biopolymer induces larger tensile and shear strengths, confirming the experimental results which show that the strength of MT increases with higher biopolymer concentration. Analysis of the bond breakage pattern suggests that at the same strain level MT stabilized with higher biopolymer concentration show less bond breakage percentage. MT specimen under greater confining pressure develops larger shear band than that under lower confining pressure. Higher biopolymer concentration induces the increase in larger inter-particle bonding strength and thus larger cracking resistance and greater macro-strength. 相似文献
3.
This paper presents a numerical investigation of shear behavior and strain localization in cemented sands using the distinct element method (DEM), employing two different failure criteria for grain bonding. The first criterion is characterized by a Mohr–Coulomb failure line with two distinctive contributions, cohesive and frictional, which sum to give the total bond resistance; the second features a constant, pressure-independent strength at low compressive forces and purely frictional resistance at high forces, which is the standard bond model implemented in the Particle Flow Code (PFC2D). Dilatancy, material friction angle and cohesion, strain and stress fields, the distribution of bond breakages, the void ratio and the averaged pure rotation rate (APR) were examined to elucidate the relations between micromechanical variables and macromechanical responses in DEM specimens subjected to biaxial compression tests. 相似文献
4.
岩石颗粒破碎是影响粒状材料剪切强度和变形的最主要因素, 岩石颗粒破碎并不是想象的那么难, 像花岗岩颗粒有时在很小的压应力作用下就可以破碎。岩石单颗粒破碎的物理试验结果常常很离散, 完成大量单颗粒破碎的物理试验费时费力不现实, 采用离散单元法(Discrete element method, DEM)PFC软件模拟单颗粒压缩破碎试验, 既能克服单颗粒破碎物理试验的缺陷, 又能解决单颗粒破碎物理试验工作量大的难题, 是研究单颗粒破碎的理想选择。基于DEM的软件PFC2D, 将粒径为0.075～0.1245mm的基本粒子捆绑成不同粒径的单颗粒, 模拟岩石单颗粒压缩破碎试验, 观察颗粒破碎演化过程, 统计单颗粒破碎强度。计算单颗粒压缩破碎后颗粒分布的分维, 验证单颗粒破碎强度的分形模型和单颗粒破碎强度的尺寸效应。文中引用玄武岩单颗粒破碎试验结果, 与单颗粒破碎的离散单元模拟结果进行比较, 验证单颗粒破碎强度的尺寸效应和修正的Weibull理论的离散单元模拟结果。 相似文献
5.
Creep tests on asphalt mixtures have been undertaken under four stress levels in the laboratory while the discrete element model (DEM) has been used to simulate the laboratory tests. A modified Burger’s model has been used to represent the time-dependent behaviour of an asphalt mixture by adding time-dependent moment and torsional resistance at contacts. Parameters were chosen to give the correct stress-strain response for constant strain rate tests in Cai et al. (2013). The stress-strain response for the laboratory creep tests and the simulations were recorded. The DEM results show reasonable agreement with the experiments. The creep simulation results proved to be dependent on both bond strength variability and positions of the particles. Bond breakage was recorded during the simulations and used to investigate the micro-mechanical deformation behaviour of the asphalt mixtures. An approach based on dimensional analysis is also presented in this paper to reduce the computational time during the creep simulation, and this analysis is also a new contribution. 相似文献
6.
Microbially induced calcite precipitation (MICP) has emerged as a novel soil improvement method. In this paper, 3-D discrete element method (DEM) simulations are used to explore the behavior of MICP-cemented sands. Comparisons of the macro-scale response of numerical and physical specimens are made. Microstructure analyses indicate a shear band formed in the numerical specimens, consistent with physical experiments. The bond breakage pattern in numerical specimens is explored and compared to observed measurements from physical specimens. The relationship between dilatancy and stress-strain behavior is evaluated. The results indicate DEM is an effective technique to capture the mechanical behavior of MICP-cemented sand. 相似文献
7.
Granular contact dynamics with elastic bond model 总被引：2，自引：2，他引：0
This paper proposes an elastic bond model in the framework of contact dynamics based on mathematic programming. The bond model developed in this paper can be used to model cemented materials. The formulation can be reduced to model pure static problems without introducing any artificial damping. In addition, omitting the elastic terms in the objective function turns the formulation into rigid bond model, which can be used for the modeling of rigid or stiffly bonded materials. The developed bond model has the advantage over the explicit DEM that large time step or displacement increment can be used. The tensile and shear strength criteria of the bond model are formulated based on the modified Mohr–Coulomb failure criterion. The torque transmission of bonds is introduced based on rolling resistance model. The loss of shear or tensile strength, or torque transmission will lead to the breakage of bonds, and turn the bond into purely frictional contact. Three simple examples are first used to validate the bond model. Numerical examples of uniaxial and biaxial compression tests are used to show its potential in modeling cemented geomaterials. Numerical results show that elastic bonds are indeed necessary for the modeling of cemented granular material under static conditions. 相似文献
8.
This paper presents a numerical investigation into mechanical behavior and strain localization in methane hydrate (MH) bearing sediments using the distinct element method (DEM). Based on the results of a series of laboratory tests on the bonded granules idealized by two glued aluminum rods and the available experimental data of methane hydrate samples, a pressure and temperature dependent bond contact model was proposed and implemented into a two-dimensional (2D) DEM code. This 2D DEM code was then used to numerically carry out a series of biaxial compression tests on the MH samples with different methane hydrate saturations, whose results were then compared with the experimental data obtained by Masui et al. [9]. In addition, stress, strain, void ratio and velocity fields, the distributions of bond breakage and averaged pure rotation rate (APR) as well as the evolution of strain localization were examined to investigate the relationships between micromechanical variables and macromechanical responses in the DEM MH samples. The numerical results show that: (1) the shear strength increases as methane hydrate saturation SMH increases, which is in good agreement with the experimental observation; (2) the strain localization in all the DEM MH samples develops with onset of inhomogeneity of void ratio, velocity, strain, APR, and distortion of stress fields and contact force chains; and (3) the methane hydrate saturation affects the type of strain localization, with one shear band developed in the case of 40.9% and 67.8% methane saturation samples, and two shear bands formed for 50.1% methane saturation sample. 相似文献
9.
A simple three‐dimensional distinct element modeling of the mechanical behavior of bonded sands 
下载免费PDF全文
下载免费PDF全文 This paper presents a simple three‐dimensional (3D) Distinct Element Method (DEM) for numerical simulation of the mechanical behavior of bonded sands. First, a series of micro‐mechanical tests on a pair of aluminum rods glued together by cement with different bond sizes were performed to obtain the contact mechanical responses of ideally bonded granular material. Second, a 3D bond contact model, which takes into account the influences of bond sizes, was established by extending the obtained 2D experimental results to 3D case. Then, a DEM incorporating the new contact model was employed to perform a set of drained triaxial compression tests on the DEM bonded specimens with different cement contents under different confining pressures. Finally, the mechanical behavior of the bonded specimens was compared with the available experimental results. The results show that the DEM incorporating the simple 3D bond contact model is able to capture the main mechanical behavior of bonded sands. The bonded specimen with higher cement content under lower confining pressure exhibits more pronounced strain softening and shear dilatancy. The peak and residual strengths, the apparent cohesion and peak/residual friction angles, and the position and slope of the critical state line increase with increase in cement content. Microscopically, bond breakage starts when the system starts to dilate and the maximum rate of bond breakage coincides with the maximum rate of dilation. Bond breakage is primarily due to tension‐shear failure and the percentage of such failures is independent of both confining pressure and cement content. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
10.
Numerical studies of shear banding in interface shear tests using a new strain calculation method 总被引：1，自引：0，他引：1
Strain localization is closely associated with the stress–strain behaviour of an interphase system subject to quasi‐static direct interface shear, especially after peak stress state is reached. This behaviour is important because it is closely related to deformations experienced by geotechnical composite structures. This paper presents a study using two‐dimensional discrete element method (DEM) simulations on the strain localization of an idealized interphase system composed of densely packed spherical particles in contact with rough manufactured surfaces. The manufactured surface is made up of regular or irregular triangular asperities with varying slopes. A new simple method of strain calculation is used in this study to generate strain field inside a simulated direct interface shear box. This method accounts for particle rotation and captures strain localization features at high resolution. Results show that strain localization begins with the onset of non‐linear stress–strain behaviour. A distinct but discontinuous shear band emerges above the rough surface just before the peak stress state, which becomes more expansive and coherent with post‐peak strain softening. It is found that the shear bands developed by surfaces with smaller roughness are much thinner than those developed by surfaces with greater roughness. The maximum thickness of the intense shear zone is observed to be about 8–10 median particle diameters. The shear band orientations, which are mainly dominated by the rough boundary surface, are parallel with the zero extension direction, which are horizontally oriented. Published in 2007 by John Wiley & Sons, Ltd. 相似文献
11.
简要介绍了颗粒抗转动模型,并将其引入离散元程序中,通过建立挡墙地基模型和合理选取模型参数,分别考虑了地基填土不同密实度和挡墙不同位移模式（被动T模式、RB模式、RT模式）情况下,刚性挡墙被动土压力随挡墙位移增长发展到达临界状态时,土压力系数 随位移发展的变化规律及墙后填土剪切带的形成规律,并与其他学者的研究成果进行对比分析。研究结果表明,土压力系数 随着挡墙位移增长的变化规律与填土的孔隙比（或相对密实度）和挡墙的位移模式紧密相关。随着孔隙比的减小或相对密实度的增大,土压力系数 会逐渐由位移硬化特性过渡为位移软化特性。尽管中密试样在双轴压缩试验中呈现出应变软化特性,而中密样的土压力系数 随着挡墙平动位移的增长可能呈现出位移软化特性,也可能呈现位移硬化特性。随着刚性挡墙向墙后土体推移,试样中的剪应变随之增大,并会在墙后形成应变局部化,即剪切带的出现。与室内试验剪应变云图相似,离散元较好地模拟了土压力临界状态时剪切带分布规律。同时,墙后土体表面不再是光滑的平面,而是逐渐隆起的凹凸面;随着挡墙位移增长,土体表面隆起量越来越大,直至土体破坏。 相似文献
12.
The failure process of brittle rock submitted to a compression state of stress with different confining pressures is investigated in this paper based on discrete element method (DEM) simulations. In the DEM model, the rock sample is represented by bonding rigid particles at their contact points. The numerical model is first calibrated by comparing the macroscopic response with the macroscopic response of Beishan granite obtained from laboratory tests. After the validation of numerical model in terms of macroscopic responses, the failure process of the DEM model under unconfined and confined compression is studied in micro‐scale in detail. The contact force network and its relation to the development of micro‐cracks and evolution of major fractures are studied. Confining pressure will prohibit the development of tensile cracks and hence alter the failure patterns. An in‐depth analysis of micro‐scale response is carried out, including the orientation distribution and probability density of stress acting on parallel bonds, the effect of particle size heterogeneity on bond breakage and the evolution of fabric tensor and coordination number of parallel bond. The proposed micromechanical analysis will allow us to extract innovative features emerged from the stresses and crack evolution in brittle rock failure process. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
13.
This article presents a fundamental study on the role of particle breakage on the shear behavior of granular soils using the three‐dimensional (3‐D) discrete element method. The effects of particle breakage on the stress ratio, volumetric strain, plastic deformation, and shear failure behavior of dense crushable specimens undergoing plane strain shearing conditions are thoroughly investigated through a variety of micromechanical analyses and mechanism demonstrations. The simulation of a granular specimen is based on the effective modeling of realistic fracture behavior of single soil particles, which is demonstrated by the qualitative agreement between the results from platen compression simulations and those from physical laboratory tests. The simulation results show that the major effects of particle breakage include the reduction of volumetric dilation and peak stress ratio and more importantly the plastic deformation mechanisms and the shear failure modes vary as a function of soil crushability. Consistent macro‐ and micromechanical evidence demonstrates that shear banding and massive volumetric contraction depict the two end failure modes of a dense specimen, which is dominated by particle rearrangement–induced dilation and particle crushing–induced compression, respectively, with a more general case being the combination and competition of the two failure modes in the medium range of soil crushability and confining stress. However, it is further shown that a highly crushable specimen will eventually develop a shear band at a large strain because of the continuous decay of particle breakage. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
14.
Natural loess is a kind of under-consolidated and unsaturated loose granulates (silts) with its microstructure characterized with large voids and inter-particle cementation. This paper presents a distinct element method (DEM) to investigate its macro- and micro-mechanical behaviour (compression and collapse behaviour) under one-dimensional (1D) compression condition. A relationship between bond strength in DEM model and initial water content is used to develop a bond contact model for loess. Then, DEM structural loess samples are prepared by the multi-layer under-compaction method, and cemented with the bond contact model. The effect of water content and void ratio on compression and collapse behaviour of loess is numerically investigated by simulating 1D compression and wetting tests on the DEM material. The DEM results agree qualitatively with available experimental observations in literatures. The wetting-induced deformation is independent of the sequence of wetting and loading under 1D compression condition. The macroscopic yielding and collapse behaviours are associated with bond breakage on microscopic scale. Moreover, bonds break in one of the two failure types in the simulations, i.e. tensile failure and shear failure (compression-shear failure and tension-shear failure), with bonds broken firstly mainly due to tension followed by shear when the samples are compressed, while mainly due to shear when the samples are wetted under a certain pressure. In addition, the contact orientations and deviator fabrics of contacts under 1D compression and wetting were also investigated. 相似文献
15.
考虑塑性应变率梯度的单轴压缩岩样轴向响应 总被引：9，自引：7，他引：2
基于剪切应变率梯度格式,采用解析方式研究了岩石材料在单轴压缩条件下的应变软化的结构响应。根据非局部连续介质模型,提出了一维二阶剪切应变率梯度格式。非局部剪切应变率与局部剪切应变率及其二阶梯度有关。将经典塑性理论中的局部剪切应变率替换为非局部剪切应变率,可以直接得到局部剪切应变率的封闭解析解,而不必通过将局部剪切应变对时间求导获得。通过对局部剪切应变率积分,得到了沿剪切带方向的相对剪切速度。试件峰值强度后的端部速度由弹性及塑性两部分构成。前一部分由虎克定律描述;后一部分与相对剪切速度有关。对弹性及塑性两部分速度求和,得到了单轴压缩岩样剪切破坏问题轴向响应的解析式。研究表明：试样高度越大、内部长度越小、剪切软化模量越大及泊松比越小,则岩样的轴向响应倾向于脆性。根据岩样与矿柱的相似性,岩样响应倾向于脆性,意味着矿柱将失去稳定性,发生矿柱岩爆。目前的基于剪切应变率梯度格式的主要优点是简洁。 相似文献
16.
3D analysis of kinematic behavior of granular materials in triaxial testing using DEM with flexible membrane boundary 总被引：2，自引：2，他引：0
This paper describes the constitutive behavior and particle-scale kinematics of granular materials in three-dimensional (3D) axisymmetric triaxial testing using discrete element method (DEM). PFC3D code was used to run the DEM simulations using a flexible membrane boundary model consisting of spherical particles linked through flexible contact bonds. The overall deformation behavior of the specimen was then compared with the specimen with rigid boundary and experimental measurements. Computed tomography was used to track the evolution of particle translation and rotation within a laboratory triaxial specimen in 3D. The DEM model of the flexible membrane specimen successfully predicted the stress–strain behavior when compared with laboratory experiment results at different confining pressures. The DEM results showed that the rigid specimen applies a uniform deformation and leads to non-uniformities in the confining stress along the particle-boundary interface in the lateral direction. In contrast, the flexible specimen better replicates the uniformly applied confining stress of a laboratory triaxial experiment. The 3D DEM simulations of the specimen with flexible membrane overpredicted particle translation and rotation in all directions when compared to a laboratory triaxial specimen. The difference between the particle translation and rotation distributions of DEM specimens with rigid and flexible membrane is almost negligible. The DEM specimen with flexible membrane produces a better prediction of the macroscopic stress–strain behavior and deformation characteristics of granular materials in 3D DEM simulations when compared to a specimen with rigid membrane. Comparing macroscale response and particle-scale kinematics between triaxial simulation results of rigid versus flexible membrane demonstrated the significant influence of boundary effects on the constitutive behavior of granular materials. 相似文献
17.
Presented is a study on the geometrical characteristics of sand particles and the mechanical behavior of sand material under external loading. Based on computed tomography technique, a reconstruction method of granular particles was developed and used to build a database of 3D geometrical models for sand particles. The studied sand particles showed good regularities in morphological characteristics and thus were suitable to be used for the random generation of numerical samples. DEM tests using realistically shaped particles were proven to better simulate the mechanical behavior of the sample during elastoplastic loading stage, which was an issue for the simplified spherical particles. The generation, extension, and breakage of the force chains controlled the strain softening behavior of sands. Anisotropy analysis using the spherical harmonic series showed that the evolution of anisotropy directions and parameters corresponded well with the macroscopic mechanical behavior of the material. Pore volume computation based on Voronoi diagram was performed to illustrate the formation and evolution of localized shear zone. The mesoscopic analysis showed that particle shape significantly influences the mechanical behavior of sands and thus should be properly modeled in numerical simulations.
相似文献18.
The cohesive‐frictional nature of cementitious geomaterials raises great interest in the discrete element method (DEM) simulation of their mechanical behavior, where a proper bond failure criterion is usually required. In this paper, the failure of bond material between two spheres was investigated numerically using DEM that can easily reproduce the failure process of brittle material. In the DEM simulations, a bonded‐grain system (composed of two particles and bond material in between) was discretized as a cylindrical assembly of very fine particles connecting two large end spheres. Then, the bonded‐grain system was subjected to compression/tension, shear, rolling and torsion loadings and their combinations until overall failure (peak state) was reached. Bonded‐grain systems with various sizes were employed to investigate bond geometry effects. The numerical results show that the compression strength is highly affected by bond geometry, with the tensile strength being dependent to a lesser degree. The shear, rolling and torsion strengths are all normal force dependent; i.e., with an increase in the normal force, these strengths first increase at a declining rate and then start to decrease upon the normal force exceeding a critical value. The combined actions of shear force, rolling moment and torque lead to a spherical failure envelope in a normalized loading space. The fitted bond geometry factors and bond failure envelopes obtained numerically in this three‐dimensional study are qualitatively consistent with those in previous two‐dimensional experiments. The obtained bond failure criterion can be incorporated into a future bond contact model. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
19.
DEM study of fabric features governing undrained post-liquefaction shear deformation of sand 总被引：3，自引：3，他引：0
In an effort to study undrained post-liquefaction shear deformation of sand, the discrete element method (DEM) is adopted to conduct undrained cyclic biaxial compression simulations on granular assemblies consisting of 2D circular particles. The simulations are able to successfully reproduce the generation and eventual saturation of shear strain through the series of liquefaction states that the material experiences during cyclic loading after the initial liquefaction. DEM simulations with different deviatoric stress amplitudes and initial mean effective stresses on samples with different void ratios and loading histories are carried out to investigate the relationship between various mechanics- or fabric-related variables and post-liquefaction shear strain development. It is found that well-known metrics such as deviatoric stress amplitude, initial mean effective stress, void ratio, contact normal fabric anisotropy intensity, and coordination number, are not adequately correlated to the observed shear strain development and, therefore, could not possibly be used for its prediction. A new fabric entity, namely the Mean Neighboring Particle Distance (MNPD), is introduced to reflect the space arrangement of particles. It is found that the MNPD has an extremely strong and definitive relationship with the post-liquefaction shear strain development, showing MNPD’s potential role as a parameter governing post-liquefaction behavior of sand. 相似文献
20.
A nonlinear parallel-bonded stress corrosion (NPSC) model is proposed to simulate the fatigue characteristics of artificial rock (concrete) during cyclic loading. Numerical simulations of fatigue tests replicate the main mechanical features of concrete specimens subjected to cyclic loading observed in the laboratory. A nonlinear reduction speed of the bond diameter between two bonded particles represents the damage rate induced by the fatigue load. The damage rate is proportional to the maximum cyclic load level when the minimum cyclic load level is fixed. Compared with laboratory data, a logarithmic function of bond diameter in the NPSC model resulted in the best fit to simulate the fatigue behaviour of concrete. The simulation includes acoustic emission (AE) monitoring during fatigue tests. The axial strain of the assembly is governed by the evolution of bond breakages. The sum of released bond strain energy is documented as value proportional to cumulative AE energy. The simulation results show very similar evolution compared with laboratory data, which verifies the effectiveness of AE energy simulation.
相似文献