首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Pile foundations are often subject to lateral loading due to various forces on a variety of structures like high rise buildings, transmission towers, power stations, offshore structures and highway and railway structures. The present investigation is to study the effect of slopes on p-y curves (where p is the static soil reaction and y is the pile deflection) due to static lateral loading in soft clay (Consistency index Ic = 0.42). A series of laboratory model tests were carried out on the instrumented model pile on sloping ground (slopes of 1V:1H, 1V:1.5H, 1V:2H, 1V:3H and 1V:5H) and with varying embedment length to diameter ratio (L/D) of 20, 25 and 30. From the experimental results, the bending moment curves along the pile shaft are double differentiated to obtain the soil resistance (p) and double integrated to obtain the deflection (y) using curve fitting method. New p-y curves for piles located on crest of soft clay with different sloping ground surface under static lateral loading are developed. Moreover, the effect of sloping angles on proposed p-y curves was studied.  相似文献   

2.
Piles supporting transmission towers, offshore structures (such as wind turbines), or infrastructures in seismic areas are frequently subjected to either one-way or two-way cyclic lateral loadings. Relatively little attention, however, has been paid to compare and understand the effects of different loading regimes (one-way or two-way cycling) on lateral responses of piles in soft clay. For this reason, a series of field tests in soft clay are carried out to compare one-way and two-way cyclic responses of single piles and of jet-grouting reinforced piles. The field tests reveal that the single pile subjected to two-way cycling experiences much more rapid degradation in lateral stiffness and capacity, but accumulates much smaller residual pile deflection (δ p), than the single pile under one-way cycling. This is because the reverse part of the two-way cycling also generates plastic strain, causing additional softening and strength reduction in the soil surrounding the pile. After each cycling, non-zero bending moment (i.e. locked in moment, or M L) is retained in the single piles, and the M L increases with the δ p. The one-way cycling leads to two times larger M L than the two-way cycling, as it causes greater δ p. The maximum M L in the pile after one-way cycling can be up to 40% of the maximum bending moment induced during the previous cyclic loading stage. After application of jet-grouting surrounding the upper part of the single pile, it greatly reduces degradation of lateral pile stiffness, accumulation of δ p and therefore development of M L. Compared to the field measurements, the API (API RP 2A-WSD, recommended practice for planning, designing, and constructing fixed offshore platform-working stress design, 21st edn. API, Washington, 2000) code underestimates the lateral stiffness of the pile under one-way cycling, while overestimates that of the pile under two-way cycling, leading to a non-conservative prediction of bending moment in the latter pile.  相似文献   

3.
The p–y method is one of the most popular methods for the analysis and design of laterally loaded piles. The mathematical relationship it provides between the bending moment, which can be easily measured at strain gauges along the pile, and the soil resistance and lateral pile displacement, facilitates the construction of p–y curves. Numerical techniques are required to fit smooth continuous curves to the discrete bending moment data in order to improve the accuracy of subsequent differentiation and integration operations. Due to the lack of guidance on the optimum positioning of strain gauges and the reliability and accuracy of curve fitting methods, a unifying study, inclusive of small (0.61 m) and large (3.8 and 7.5 m) diameter piles in clay, was carried out using 18 strain gauge layouts and cubic spline, cubic to quintic B-spline and 3rd to 10th degree global polynomial techniques. Bending moment data was obtained using 3D finite element analysis. Through a comprehensive evaluation, the cubic and cubic B-spline methods were found to be consistently accurate in deriving p–y curves for both the small and large diameter piles.  相似文献   

4.
A series of centrifuge model tests was conducted to investigate the failure mechanism of pile-reinforced slopes under self-weight loading and vertical loading conditions. An integrated analysis method was proposed based on the image-based measurement results of the displacement of the slope in the tests. The failure process of a pile-reinforced slope was quantified based on the measured deformation process over the entire slope, which was shown to depend primarily on the loading conditions. The deformation localisation was discovered in the slope during loading and was effectively described using a newly introduced index, the Diversity Factor of Displacement (DFD). The deformation localisation of the slope developed and caused the progressive formation of the slip surface. At the same time, a local failure at a point on the slip surface resulted in new deformation localisation, and the influence expanded with the centre of the failure point and waned with increasing distance from the failure point. The deformation localisation process and the deformation-failure process of the piles interacted as both cause and effect and developed alternately. The failure mechanism of the pile-reinforced slopes was used to explain the effects of several influencing factors on the bearing capacity of the reinforced slope, such as the pile spacing, pile location, and gradient of the slope.  相似文献   

5.
This paper presents the numerical simulation of pile installation and the subsequent increase in the pile capacity over time (or setup) after installation that was performed using the finite element software Abaqus. In the first part, pile installation and the following load tests were simulated numerically using the volumetric cavity expansion concept. The anisotropic modified Cam-Clay and Dracker–Prager models were adopted in the FE model to describe the behavior of the clayey and sandy soils, respectively. The proposed FE model proposed was successfully validated through simulating two full-scale instrumented driven pile case studies. In the second part, over 100 different actual properties of individual soil layers distracted from literature were used in the finite element analysis to conduct parametric study and to evaluate the effect of different soil properties on the pile setup behavior. The setup factor A was targeted here to describe the pile setup as a function of time after the end of driving. The selected soil properties in this study to evaluate the setup factor A include: soil plasticity index (PI), undrained shear strength (S u ), vertical coefficient of consolidation (C v ), sensitivity ratio (S r ), and over-consolidation ratio (OCR). The predicted setup factor showed direct proportion with the PI and S r and inverse relation with S u , C v and OCR. These soil properties were selected as independent variables, and nonlinear multivariable regression analysis was performed using Gauss–Newton algorithm to develop appropriate regression models for A. Best models were selected among all based on level of errors of prediction, which were validated with additional nineteen different site information available in the literature. The results indicated that the developed model is able to predict the setup behavior for individual cohesive soil layers, especially for values of setup factor greater than 0.10, which is the most expectable case in nature.  相似文献   

6.
The South Jingyang Plateau, with a total area of 70 km2, is located in Shaanxi Province, China. Since 1976, more than 50 landslides of different types have occurred repeatedly on the edge slopes of the plateau due to the start of diversion irrigation on the plateau, resulting in great loss of lives and property. To better understand the initiation and movement mechanisms of these loess landslides, we surveyed them and carried out a detailed investigation of a large landslide in the Xihetan area. Our field survey results revealed that although most of these landslides had a long runout with high mobility, most of the landslide materials originating from the edge slopes may have been in an unsaturated state when the landslide occurred. This suggests that the materials at the toe of the edge slope as well as on the travel path along the river terrace might have played a key role in landslide movement. To examine how the materials on the travel path were involved in the landsliding, we used a multichannel surface wave technique and surveyed shear wave velocity (V s ) profiles of the landslide deposits. We also examined the internal geometry of the deposits that outcropped on the right-side slope of the landslide foot. The longitudinal profile of V s along the direction of movement showed that terrace deposits near the toe of the edge slope may have been sheared upward, indicating that at the toe, the surface of rupture might be located inside the terrace deposits. The V s contours showed an A-shaped fold within the landslide deposits in the middle part of the travel path and became greater in the most distal toe part. The V s profile across the deposits showed a U-shaped belt, in which the soil layers have smaller V s . This belt may be the boundary between the sliding landslide debris and terrace deposits. The observed internal geometry of the landslide deposits indicates that a sliding surface developed within the sandy layer underlying the gravel layer. Therefore, we inferred that after failure, the displaced landslide materials overrode and sheared the terrace deposits along its main sliding direction, resulting in the formation of thrust folds within the terrace deposits, and greater V s on the distal toe part of the landslide.  相似文献   

7.
Random finite element method (RFEM) provides a rigorous tool to incorporate spatial variability of soil properties into reliability analysis and risk assessment of slope stability. However, it suffers from a common criticism of requiring extensive computational efforts and a lack of efficiency, particularly at small probability levels (e.g., slope failure probability P f ?<?0.001). To address this problem, this study integrates RFEM with an advanced Monte Carlo Simulation (MCS) method called “Subset Simulation (SS)” to develop an efficient RFEM (i.e., SS-based RFEM) for reliability analysis and risk assessment of soil slopes. The proposed SS-based RFEM expresses the overall risk of slope failure as a weighed aggregation of slope failure risk at different probability levels and quantifies the relative contributions of slope failure risk at different probability levels to the overall risk of slope failure. Equations are derived for integrating SS with RFEM to evaluate the probability (P f ) and risk (R) of slope failure. These equations are illustrated using a soil slope example. It is shown that the P f and R are evaluated properly using the proposed approach. Compared with the original RFEM with direct MCS, the SS-based RFEM improves, significantly, the computational efficiency of evaluating P f and R. This enhances the applications of RFEM in the reliability analysis and risk assessment of slope stability. With the aid of improved computational efficiency, a sensitivity study is also performed to explore effects of vertical spatial variability of soil properties on R. It is found that the vertical spatial variability affects the slope failure risk significantly.  相似文献   

8.
During the last earthquake that occurred in Chlef (El Asnam 1980, Algeria), a significant decrease in the shear strength has caused major damages to several civil and hydraulic structures (earth dams, embankments, bridges, slopes and buildings), especially for the saturated sandy soil of the areas near Chlef valley. This paper presents a laboratory study of drained compression triaxial tests conducted on sandy soil reinforced with horizontal layers of geotextile, in order to study the influence of geotextile layer characteristics both on shear stress–strain and on volumetric change–strain. Tests were carried out on medium and dense sand. The experimental programme includes some drained compression tests performed on reinforced sand samples, for different values of the geotextile layers number (N g), of confining pressure (\( \sigma_{\text{c}}^{\prime } \)) and relative density (D r). The test results have shown that the contribution of the geotextile at low values of the axial strain (ε 1) is negligible, for higher values of (ε 1); geotextile induces a quasi-linear increase in the deviator stress (q) and leads to an increase in the volume contractiveness within the reinforced samples. A negligible influence of geotextile layers number (N g) on the stress–strain behaviour and the volumetric change has been shown, when normalized with N g. The results indicate that the contribution of geotextile to the stress–strain mobilization increases with increasing confining pressure, while its contribution to the volume contraction decreases with the increase in the confining pressure.  相似文献   

9.
Luo  Fangyue  Huang  Renlong  Zhang  Ga 《Acta Geotechnica》2020,15(10):3027-3040

A series of centrifuge model tests of geogrid-reinforced slopes with superstructure was conducted under differential settlement condition. The influence of reinforcement placement on the deformation and failure behavior of the slope and superstructure is investigated by considering different numbers of geogrid layers. The response of the slope and superstructure is analyzed based on a full-field displacement measurement via image analysis. The differential settlement induces distinguishable superstructure movement and slope deformation above the subsidence zone. The slope displacement, close to the vertical direction, appears only in a limited zone. An integrated analysis scheme of deformation and failure processes is adopted to reveal the failure mechanism of both the unreinforced and reinforced slopes: a certain level of deformation localization induced by differential settlement results in the local failure, and adversely, the local failure aggravates the deformation localization near it. The geogrid reinforcement mechanism is further clarified as the reduction on the deformation localization of the slope due to geogrid placement. The geogrid reinforcement effect can be comprehensively described with two respects: hooping effect and shielding effect, which illustrates the influence sphere and degree of geogrid reinforcement on restraining the slope deformation. The geogrid reinforcement is proven effective to improve the safety of the slope and superstructure.

  相似文献   

10.
The distribution of permafrost-related slope failures along the Qinghai-Tibet Highway from Wuddaoliang to Fenghuoshan correlates with ice content, slope gradient, and ground temperature. Slope failures are of two types. (1) Retrogressive thaw slumps result from icy permafrost being exposed by either man-induced excavation or fluvial-thermal erosion and undercutting of basal slopes. (2) Active-layer-detachment failures are caused by thaw of icy permafrost at the active layer-permafrost interface. After initial failure, active-layer-detachment failures can lead to retrogressive thaw-slumping and localized surficial landslide. Common trigger mechanisms for failure include high summer air temperatures and heavy summer precipitation. A third possible trigger mechanism for slope failure is earthquake occurrence. A geotechnical slope stability analysis was undertaken for an active-layer-detachment failure that had progressed into a retrogressive thaw slump. A safety factor (F s ) of 1.24 for the natural slope was determined using in situ tested strength parameters. However, the slope would lose stability when either the groundwater level over the permafrost table exceeded 1.42 m or seismic acceleration reached, or exceeded, 0.03?g.  相似文献   

11.
This paper investigates, using the random field theory and Monte Carlo simulation, the effects of random field discretization on failure probability, p f, and failure mechanism of cohesive soil slope stability. The spatial sizes of the discretized elements in random field Δx, Δy in horizontal and vertical directions, respectively, are assigned a series of combinational values in order to model the discretization accuracy. The p f of deterministic critical slip surface (DCSS) and that of the slope system both are analyzed. The numerical simulation results have demonstrated that both the ratios of Δy/λ y (λ y  = scale of fluctuation in vertical direction) and Δx/λ x (λ x  = scale of fluctuation in horizontal direction) contribute in a similar manner to the accuracy of p f of DCSS. The effect of random field discretization on the p f can be negligible if both the ratios of Δx/λ x and Δy/λ y are no greater than 0.1. The normalized discrepancy tends to increase at a linear rate with Δy/λ y when Δx/λ x is larger than 0.1, and vice versa for p f of DCSS. The random field discretization tends to have more considerable influence on the p f of DCSS than on that of the slope system. The variation of p f versus λ x and λ y may exhibit opposite trends for the cases where the limit state functions of slope failure are defined on DCSS and on the slope system as well. Finally, the p f of slope system converges in a more rapid manner to that of DCSS than the failure mechanism does to DCSS as the spatial variability of soil property grows from significant to negligible.  相似文献   

12.
Rainfall infiltration is the main factor that causes slope instability. To study the effect of hydraulic parameters on the final saturation line and stability of slopes, a numerical slope model is established with a saturated–unsaturated seepage analysis method. Analysis results show the following, (1) When parameter a increases, the effective rainfall duration decreases linearly, and the ultimate safety factor increases gradually; when parameter m increases, the effective rainfall duration increases linearly, and the ultimate safety factor decreases linearly; when parameter n increases, both the effective rainfall duration and the ultimate safety factor decrease first and then remain stable. (2) When the saturated permeability coefficient decreases, the effective rainfall duration presents a crescent trend, and the ultimate safety factor decreases first and then remains the same after rainfall intensity exceeds the saturated permeability coefficient of soil. (3) When rainfall intensity is less than the saturated permeability coefficient of soil, the location of the final saturation line rises as the saturated permeability coefficient decreases and is thus independent of parameters a, m, and n.  相似文献   

13.
Root systems of trees reinforce the underlying soil in hillslope environments and therefore potentially increase slope stability. So far, the influence of root systems is disregarded in Geographic Information System (GIS) models that calculate slope stability along distinct failure plane. In this study, we analyse the impact of different root system compositions and densities on slope stability conditions computed by a GIS-based slip surface model. We apply the 2.5D slip surface model r.slope.stability to 23 root system scenarios imposed on pyramidoid-shaped elements of a generic landscape. Shallow, taproot and mixed root systems are approximated by paraboloids and different stand and patch densities are considered. The slope failure probability (Pf) is derived for each raster cell of the generic landscape, considering the reinforcement through root cohesion. Average and standard deviation of Pf are analysed for each scenario. As expected, the r.slope.stability yields the highest values of Pf for the scenario without roots. In contrast, homogeneous stands with taproot or mixed root systems yield the lowest values of Pf. Pf generally decreases with increasing stand density, whereby stand density appears to exert a more pronounced influence on Pf than patch density. For patchy stands, Pf increases with a decreasing size of the tested slip surfaces. The patterns yielded by the computational experiments are largely in line with the results of previous studies. This approach provides an innovative and simple strategy to approximate the additional cohesion supplied by root systems and thereby considers various compositions of forest stands in 2.5D slip surface models. Our findings will be useful for developing strategies towards appropriately parameterising root reinforcement in real-world slope stability modelling campaigns.  相似文献   

14.
In this study, dynamic centrifuge model tests were conducted to investigate the dynamic response of cohesive soil slopes with the use of stabilizing piles during an earthquake. The behavior of the pile reinforcement was analyzed based on the obtained deformation over the entire slope through image-based measurement, and the behavior of the slope was compared to that of an unreinforced slope. The piles significantly increased the stability of the slope and reduced its deformation during an earthquake. The bending moment of the piles exhibited a nearly triangular distribution due to the earthquake. The acceleration response of the slope increased with increasing elevation, and the displacement accumulated apparently irreversibly over the course of the earthquake. The piles significantly affected the deformation of the slope in a certain area, the boundary of which was defined using a continuous surface. A strain analysis of the slope demonstrated that the piles had a significant effect on the reduction in the deformation of the slope in their vicinities, and this effect expanded upward along the slope and arrested the possible slip surface that would have occurred in an unreinforced slope. Several influencing factors were simulated in the tests, and observation of these factors demonstrated that the dynamic response of the pile-reinforced slope was affected by the pile spacing, pile location, slope gradient, and input earthquake to varying extent.  相似文献   

15.
In this study, a series of natural dam overtopping laboratory tests are reported. In these tests, the effect of seven different sediment mixtures on the breaching process was investigated. According to the test results, three stages of the breaching process of natural dams made of different materials were observed. Backward erosion was the primary cause for the incising slopes. The effects of backward erosion became stronger with the larger fines contents of the materials. With an increase in the median diameter (d 50) of particles, the breaching time became longer. However, the peak discharge became smaller. With an increase in the fines contents (p), the median diameter of the particles and the void ratio were changed, which resulted in a decrease in the breaching time and an increase in the peak discharge. The breaching time and peak discharge were more sensitive to the median diameter than to the fines contents. The relation between breach width and depth was found to follow a logistic function \( W\kern0.5em =\kern0.5em \frac{\zeta }{1\kern0.5em +\kern0.5em {e}^{\left(-k\left(D\kern0.5em -\kern0.5em {D}_0\right)\right)}} \). The parameters ζ, k, and D 0 are defined by a linear relationship with the median diameter and fines content. A breach of the side slope occurred as a tensile failure when the fines contents of the materials were large; otherwise, shear failure occurred. Furthermore, when the materials had fewer fines contents, the volume of the collapsed breach side slope became larger.  相似文献   

16.
In order to study the dynamic response characteristics of a rock slope with discontinuities under the combined action of earthquakes and rapid water drawdown, a large-scale shaking table test was performed on a rock slope with discontinuous joints. Wenchuan earthquake (WE) seismic records were performed to investigate the horizontal and vertical acceleration response and displacement response. In particular, three-dimensional optical measurement techniques was used to obtain the slope surface displacements. A comparison was made on the seismic response according to the analysis of PGD (peak ground displacement) and M PGA (acceleration amplification coefficient) of the modeled slope. The results show that the experimental slope mainly underwent settlement and horizontal deformation when the WE records were applied in the z and x directions, respectively. The slope was first shaken by the P wave, which caused the differential settlement to occur at the surface slope; then, the slope was shaken more severely by the S wave, which led to a greater horizontal deformation. Moreover, analysis of the ΔPGD (increment of PGD) and ΔM PGA (increment of M PGA) under rapid drawdown suggests that the rapid water drawdown mainly impacts the deformation of the surface slope, particularly between the high and low water levels. The water infiltration through the cracks softened the material of the surface slope, and the rapid drawdown also enhanced the slope deformation. In addition, the damage evolution process of the slope can be identified, mainly including three stages: an elastic stage (<?0.168 g), a plastic stage (0.168–0.336 g), and a failure stage (>?0.336 g).  相似文献   

17.
A micromechanics-based approach is proposed to predict the shear failure of brittle rocks under compression. Formulation of this approach is based on an improved wing microcrack model, the Mohr-Coulomb failure criterion, and a micro-macro damage model. The improved wing microcrack model considers the effects of crack inclination angle on mechanical behaviors of rocks. The micro-macro damage model describes the relation between crack growth and axial strain. Furthermore, comparing experimental and theoretical relations between crack initiation stress and confining pressure, model parameters (i.e., μ, a, β, and φ) hardly measured by test are solved. Effects of crack inclination angle, crack size, and friction coefficient on stress-strain relation, compressive strength, internal friction angle, cohesion, shear failure plane angle, and shear strength are discussed in details. A most disadvantaged crack angle is found, which is corresponding to the smallest compressive strength, cohesion, internal friction angle, and shear strength of rocks. Rationality of the theoretical results is verified by the published experimental results. This approach provides a theoretical prediction for effects of microcrack geometry on macroscopic shear properties in brittle rocks under compression.  相似文献   

18.
In order to solve the bulging deformation and fracture at the top of widely used gravel piles in treating ground consolidation, a new, optimized composite foundation form was proposed. The composite foundation was constructed using discrete materials and concrete piles. Additionally, various parameters of this new composite foundation were analyzed, including foundation forms, construction technologies, bearing mechanism and failure mode. By applying cavity expansion theory, the Vesic cavity spreading pressure of the discrete material-concrete pile is solved as a polar axis symmetric problem on the basis of Mohr–Coulomb yield criterion. Then the computing formula for the ultimate bearing capacity of the discrete materials-concrete pile is elicited when the internal friction angle of soil in the piles is φ = 0 and φ ≠ 0. Finally, the ultimate bearing capacity value of the composite foundation is acquired through analytic calculation and numerical simulation. Finally, it is found that the calculation result is 14.4% lower than that of the simulated result, which is within the acceptable accuracy range and therefore proves the accuracy of the analytic calculation method for bearing capacity of the new composite foundation.  相似文献   

19.
Thermal properties of ground heat exchanger (GHE) such as effective thermal conductivity and borehole thermal resistance are commonly measured in the field by thermal response tests (TRTs). TRT has been proved to be a consolidated method to determine thermal properties of traditional borehole heat exchangers (BHEs). However, there is still lack of data for adopting TRT on energy piles with often a large diameter and deficiency in validation of TRT results with geological materials. In this study, ground thermal properties for typical configured GHEs of energy piles are investigated. Three TRTs are conducted and the obtained results are analyzed. Effective thermal conductivity, λeff, of the ground derived by following the traditional linear source model shows large deviation as compared to the thermal conductivity of the geological materials. In order to determine λeff properly, the linear source model is modified and an equivalent radius, req, of energy piles is considered. The λeff estimated by the modified model shows a good agreement with thermal conductivity of the in situ geological materials. In addition, there has been no obvious correlation between borehole thermal resistances and thermal efficiency due to heat transport of energy piles that depends not only by borehole thermal resistance but also by the pile’s diameter and ground conditions. The findings drawn from this study indicate that the modified model is reasonable and useful in determining thermal properties of energy piles.  相似文献   

20.
It is essential to determine the shear strength parameters c and φ on the sliding surface for stability evaluation and engineering design of a landslide. In this study, a new parameter back analysis method is proposed by combining the 2D/3D upper bound method of limit analysis and reliability theory to accurately determine the shear strength parameters for a 3D slope with a single failure surface. The proposed reliability back analysis method overcomes the shortcomings of the traditional deterministic analysis method of slope stability that cannot take into account the randomness and uncertainty of geotechnical parameters. Based on the reliability theory, two methods were studied: first-order reliability method (implemented by spreadsheet and Matlab, called spreadsheet method and constrained optimization method, respectively, in this paper) and Monte Carlo simulation. The optimized values of c and φ were obtained by establishing only one balance equation with the consideration of the pore water pressure or other complex conditions, which can solve the problem of the back analysis of strength parameters for a single 3D sliding surface condition. The correlation research showed that the negative correlation between c and φ greatly affected the back analysis results, and the reliability index values were conservative without considering such a negative correlation. A case study for the back analysis of shear strength parameters is conducted based on a practical landslide model with a broken line slip surface slope in Zhuquedong village, Luxi town, Xiangxi County, Hunan Province, China, and a suggestion for the selection of landslide cross section is presented. The results show that the back analysis results determined by the reliability theory coincide well with the survey and experimental results. The proposed method is found to be more accurate and effective in determining the values of shear parameters than that of the traditional deterministic inversion method.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号