首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 218 毫秒
1.
Average elastic properties of a fluid‐saturated fractured rock are discussed in association with the extremely slow and dispersive Krauklis wave propagation within individual fractures. The presence of the Krauklis wave increases P‐wave velocity dispersion and attenuation with decreasing frequency. Different laws (exponential, power, fractal, and gamma laws) of distribution of the fracture length within the rock show more velocity dispersion and attenuation of the P‐wave for greater fracture density, particularly at low seismic frequencies. The results exhibit a remarkable difference in the P‐wave reflection coefficient for frequency and angular dependency from the fractured layer in comparison with the homogeneous layer. The biggest variation in behaviour of the reflection coefficient versus incident angle is observed at low seismic frequencies. The proposed approach and results of calculations allow an interpretation of abnormal velocity dispersion, high attenuation, and special behaviour of reflection coefficients versus frequency and angle of incidence as the indicators of fractures.  相似文献   

2.
The paper is concerned with the propagation of the Love waves in an inhomogeneous transversely isotropic fluid saturated porous layered half-space with linearly varying properties. The analysis is based on Biot's theory. Firstly, the dispersion equation in the complex form for the Love waves in an inhomogeneous porous layer is derived. Then the equation is solved by an iterative method. Detailed numerical calculation is presented for an inhomogeneous fluid saturated porous layer overlying a purely elastic half-space. The dispersion and attenuation of the Love waves are discussed. In addition, the upper and lower bounds of the Love wave speed are explored.  相似文献   

3.
  相似文献   

4.
Ultrasonic (500 kHz) P‐ and S‐wave velocity and attenuation anisotropy were measured in the laboratory on synthetic, octagonal‐shaped, silica‐cemented sandstone samples with aligned penny‐shaped voids as a function of pore fluid viscosity. One control (blank) sample was manufactured without fractures, another sample with a known fracture density (measured from X‐ray CT images). Velocity and attenuation were measured in four directions relative to the bedding fabric (introduced during packing of successive layers of sand grains during sample construction) and the coincident penny‐shaped voids (fractures). Both samples were measured when saturated with air, water (viscosity 1 cP) and glycerin (100 cP) to reveal poro‐visco‐elastic effects on velocity and attenuation, and their anisotropy. The blank sample was used to estimate the background anisotropy of the host rock in the fractured sample; the bedding fabric was found to show transverse isotropy with shear wave splitting (SWS) of 1.45 ± 1.18% (i.e. for S‐wave propagation along the bedding planes). In the fractured rock, maximum velocity and minimum attenuation of P‐waves was seen at 90° to the fracture normal. After correction for the background anisotropy, the fractured sample velocity anisotropy was expressed in terms of Thomsen's weak anisotropy parameters ε, γ & δ. A theory of frequency‐dependent seismic anisotropy in porous, fractured, media was able to predict the observed effect of viscosity and bulk modulus on ε and δ in water‐ and glycerin‐saturated samples, and the higher ε and δ values in air‐saturated samples. Theoretical predictions of fluid independent γ are also in agreement with the laboratory observations. We also observed the predicted polarisation cross‐over in shear‐wave splitting for wave propagation at 45° to the fracture normal as fluid viscosity and bulk modulus increases.  相似文献   

5.
The simplified macro‐equations of porous elastic media are presented based on Hickey's theory upon ignoring effects of thermomechanical coupling and fluctuations of porosity and density induced by passing waves. The macro‐equations with definite physical parameters predict two types of compressional waves (P wave) and two types of shear waves (S wave). The first types of P and S waves, similar to the fast P wave and S wave in Biot's theory, propagate with fast velocity and have relatively weak dispersion and attenuation, while the second types of waves behave as diffusive modes due to their distinct dispersion and strong attenuation. The second S wave resulting from the bulk and shear viscous loss within pore fluid is slower than the second P wave but with strong attenuation at lower frequencies. Based on the simplified porous elastic equations, the effects of petrophysical parameters (permeability, porosity, coupling density and fluid viscosity) on the velocity dispersion and attenuation of P and S waves are studied in brine‐saturated sandstone compared with the results of Biot's theory. The results show that the dispersion and attenuation of P waves in simplified theory are stronger than those of Biot's theory and appear at slightly lower frequencies because of the existence of bulk and shear viscous loss within pore fluid. The properties of the first S wave are almost consistent with the S wave in Biot's theory, while the second S wave not included in Biot's theory even dies off around its source due to its extremely strong attenuation. The permeability and porosity have an obvious impact on the velocity dispersion and attenuation of both P and S waves. Higher permeabilities make the peaks of attenuation shift towards lower frequencies. Higher porosities correspond to higher dispersion and attenuation. Moreover, the inertial coupling between fluid and solid induces weak velocity dispersion and attenuation of both P and S waves at higher frequencies, whereas the fluid viscosity dominates the dispersion and attenuation in a macroscopic porous medium. Besides, the heavy oil sand is used to investigate the influence of high viscous fluid on the dispersion and attenuation of both P and S waves. The dispersion and attenuation in heavy oil sand are stronger than those in brine‐saturated sandstone due to the considerable shear viscosity of heavy oil. Seismic properties are strongly influenced by the fluid viscosity; thus, viscosity should be included in fluid properties to explain solid–fluid combination behaviour properly.  相似文献   

6.
P‐ and S‐wave velocity and attenuation coefficients (accurate to ±0.3% and ±0.2 dB/cm, respectively) were measured in synthetic porous rocks with aligned, penny‐shaped fractures using the laboratory ultrasonic pulse‐echo method. Shear‐wave splitting was observed by rotating the S‐wave transducer and noting the maximum and minimum velocities relative to the fracture direction. A block of synthetic porous rock of fracture density 0.0201 ± 0.0068 and fracture size 3.6 ± 0.38 mm (measured from image analysis of X‐ray CT scans) was sub‐sampled into three 20–30 mm long, 50 mm diameter core plugs oriented at 0°, 45° and 90° to the fracture normal (transversely isotropic symmetry axis). Full waveform data were collected over the frequency range 500–1000 kHz for both water and glycerin saturated cores to observe the effect of pore fluid viscosity at 1 cP and 100 cP, respectively. The shear‐wave splitting observed in the 90° core was 2.15 ± 0.02% for water saturated and 2.39 ± 0.02% for glycerin saturated, in agreement with the theory that suggests that the percentage splitting should be 100 times the fracture density and independent of the saturating fluid. In the 45° core, by contrast, splitting was 0.00 ± 0.02% for water saturation and ?0.77 ± 0.02% for glycerin saturation. This dependence on fracture orientation and pore fluid viscosity is consistent with the poro‐visco‐elastic theory for aligned, meso‐scale fractures in porous rocks. The results suggest the possible use of shear‐ or converted‐wave data to discriminate between fluids on the basis of viscosity variations.  相似文献   

7.
The analysis of Stoneley wave propagation in a fracture is essential for the identification and evaluation of fracture parameters from the borehole Stoneley wave. Also, it is important for many geophysics considerations, e.g. for tremor and long-period events observed in volcanoes and geothermal areas. In this paper, we investigate the guided waves propagation in a fluid layer lying between two viscoelastic vertically transversely isotropic media. The viscoelastic mechanism models the attenuation due to the presence of fluid saturation in the rock. A model based on the superposition of three inhomogeneous partial plane waves: one in the fluid and two heterogeneous waves in the solid is developed. The dispersion equation is obtained for this case. A numerical solution is carried out to obtain the guided wave velocity and attenuation coefficient. The results of this investigation show that there is a strong correlation between the velocity dispersion and attenuation of Stoneley wave and the anisotropic parameters of the medium especially in a sandstone (fast) medium.  相似文献   

8.
Wave‐induced fluid flow plays an important role in affecting the seismic dispersion and attenuation of fractured porous rocks. While numerous theoretical models have been proposed for the seismic dispersion and attenuation in fractured porous rocks, most of them neglect the wave‐induced fluid flow resulting from the background anisotropy (e.g. the interlayer fluid flow between different layers) that can be normal in real reservoirs. Here, according to the theories of poroelasticity, we present an approach to study the frequency‐dependent seismic properties of more realistic and complicated rocks, i.e. horizontally and periodically layered porous rock with horizontal and randomly orienting fractures, respectively, distributed in one of the two periodical layers. The approach accounts for the dual effects of the wave‐induced fluid flow between the fractures and the background pores and between different layers (the interlayer fluid flow). Because C33 (i.e., the modulus of the normally incident P‐wave) is directly related to the P‐wave velocity widely measured in the seismic exploration, and its comprehensive dispersion and attenuation are found to be most significant, we study mainly the effects of fracture properties and the stiffness contrast between the different layers on the seismic dispersion and attenuation of C33. The results show that the increasing stiffness contrast enhances the interlayer fluid flow of the layered porous rocks with both horizontal and randomly orienting fractures and weakens the wave‐induced fluid flow between the fractures and the background pores, especially for the layered porous rock with horizontal fractures. The modelling results also demonstrate that for the considered rock construction, the increasing fracture density reduces the interlayer fluid flow while improves the dispersion and attenuation in the fracture‐relevant frequency band. Increasing fracture aspect ratio is found to reduce the dispersion and attenuation in the fracture‐relevant frequency band only, especially for the layered porous rock with horizontal fractures.  相似文献   

9.
A fluid‐saturated flat channel between solids, such as a fracture, is known to support guided waves—sometimes called Krauklis waves. At low frequencies, Krauklis waves can have very low velocity and large attenuation and are very dispersive. Because they propagate primarily within the fluid channel formed by a fracture, Krauklis waves can potentially be used for geological fracture characterization in the field. Using an analogue fracture consisting of a pair of flat slender plates with a mediating fluid layer—a trilayer model—we conducted laboratory measurements of the velocity and attenuation of Krauklis waves. Unlike previous experiments using ultrasonic waves, these experiments used frequencies well below 1 kHz, resulting in extremely low velocity and large attenuation of the waves. The mechanical compliance of the fracture was varied by modifying the stiffness of the fluid seal of the physical fracture model, and proppant (fracture‐filling high‐permeability sand) was also introduced into the fracture to examine its impact on wave propagation. A theoretical frequency equation for the trilayer model was derived using the poroelastic linear‐slip interface model, and its solutions were compared to the experimental results.  相似文献   

10.
致密砂岩普遍具有低孔、低渗及微裂缝发育的地质特征,并且呈现出很强的非均匀性.致密砂岩储层与常规砂岩储层比较,具有明显的岩石物理性质、渗流力学性质方面的差异.致密砂岩内部的非均匀性对弹性波频散、衰减有显著影响,其中包括孔隙结构的非均匀性,即岩石内部孔隙参数的不均一性,以及孔隙内部不相混溶流体的非均匀分布;此外,非均匀性的尺度也决定了波出现显著频散与衰减的频段.综合考虑致密砂岩孔隙结构非均匀性及流体斑块状饱和的非均匀性,本文采用双双重孔隙介质结构模拟了致密砂岩的弹性波响应,分析了同时具备两类非均质性岩石中的波传播特征.调查分析了两组分别来自中国鄂尔多斯盆地苏里格气田及四川盆地广安气田的不同类型致密砂岩储层的岩芯超声波实验数据,给出了岩石样本的弹性波速度频散与衰减曲线.结果显示理论模型预测结果与完全饱和、部分饱和岩石的实验数据吻合良好.对两个地区致密砂岩岩芯数据进行对比分析,苏里格致密砂岩样本总体上比广安致密砂岩渗透率高,在各孔隙度范围内,特征模拟显示苏里格样本的裂隙尺寸明显大于广安样本.广安致密砂岩在低孔隙度范围内发育了更多、更小的颗粒裂隙/接触.致密砂岩的速度频散与衰减结果受流体黏度、晶体破裂及流体斑块状饱和的共同影响.此外,孔隙度越大,部分饱和岩石中斑块状饱和机制对总衰减的贡献越低,与之相对,结构非均质性所占的比重则有所增强.  相似文献   

11.
流体在断裂和岩石骨架间的交换被认为是影响岩石弹性参数各向异性的主要原因,理论研究表明断裂尺度同样对弹性参数的各向异性也有影响.为了说明两者对各向异性影响以实现多尺度断裂裂隙的识别,本文在等效介质模型的基础上,应用数值分析的方法研究速度和衰减(1/Q)随多尺度断裂、频率和流体因子变化规律.结果表明介质弹性参数是频率依赖的,并且参数中存在衰减项,而这种频率依赖性与介质物性参数中的断裂尺度及流体性质存在一定的联系;当断裂定向分布时,参数结果显示为各向异性;不同断裂尺度具有不同的波速频散特性,剪切波分裂程度依赖于频率,断裂尺度起着控制作用,高频时对小尺度的敏感,低频段对大尺度敏感.在地震频段Thomsen参数随着频率的增大而减小,随着断裂尺寸的增大而减小.因此地震数据可能区分断裂和微裂隙引起各向异性,从而可测量断裂尺度.  相似文献   

12.
The propagation of elastic waves in a medium containing many inclusions is considered. Under the assumption that the spatial distribution of inclusions is uniform, a general equation is derived for the determination of the velocity dispersion and attenuation coefficient of the effective waves. A simple example is presented where scatterers are infinitesimally thin cracks. The calculated results show that the attenuation coefficient Q?1 takes a peak value for the wavelength nearly equal to twice the crack length.  相似文献   

13.
本文首先由Christoffel方程推导出黏弹性EDA介质中均匀、 非均匀P波、 SV波和SH波的相速度表达式, 然后参照极端各向异性介质的相关计算方法, 推导出EDA介质中均匀、 非均匀地震波相衰减系数和群衰减系数的表达式, 并通过数值计算分析了相速度、 相衰减系数、 群衰减系数与裂隙方位的关系. 结果表明: 均匀介质中SH波的相速度和相衰减系数均可指示裂隙的走向; 非均匀介质中SH波相衰减系数随非均匀角的增大而增大, 且其对称轴与介质对称轴的夹角也相应增加; 由于地震波振幅的衰减随岩石物理性质的变化比地震波速度的变化更为灵敏, 而且携带了更多的岩石物理性质信息, 因此可用来探明裂隙走向、 密度及含水特性, 进而应用于预测、 预防地下工程地质灾害事故.   相似文献   

14.
When a porous layer is permeated by mesoscale fractures, wave-induced fluid flow between pores and fractures can cause significant attenuation and dispersion of velocities and anisotropy parameters in the seismic frequency band. This intrinsic dispersion due to fracturing can create frequency-dependent reflection coefficients in the layered medium. In this study, we derive the frequency-dependent PP and PS reflection coefficients versus incidence angle in the fractured medium. We consider a two-layer vertical transverse isotropy model constituted by an elastic shale layer and an anelastic sand layer. Using Chapman's theory, we introduce the intrinsic dispersion due to fracturing in the sand layer. Based on the series coefficients that control the behaviour of velocity and anisotropy parameters in the fractured medium at low frequencies, we extend the conventional amplitude-versus-offset equations into frequency domain and derive frequency-dependent amplitude-versus-offset equations at the elastic–anelastic surface. Increase in fracture length or fracture density can enlarge the frequency dependence of amplitude-versus-offset attributes of PP and PS waves. Also, the frequency dependence of magnitude and phase angle of PP and PS reflection coefficients increases as fracture length or fracture density increases. Amplitude-versus-offset type of PP and PS reflection varies with fracture parameters and frequency. What is more, fracture length shows little impact on the frequency-dependent critical phase angle, while the frequency dependence of the critical phase angle increases with fracture density.  相似文献   

15.
Measurements of seismic anisotropy in fractured rock are used at present to deduce information about the fracture orientation and the spatial distribution of fracture intensity. Analysis of the data is based upon equivalent-medium theories that describe the elastic response of a rock containing cracks or fractures in the long-wavelength limit. Conventional models assume frequency independence and cannot distinguish between microcracks and macrofractures. The latter, however, control the fluid flow in many subsurface reservoirs. Therefore, the fracture size is essential information for reservoir engineers. In this study we apply a new equivalent-medium theory that models frequency-dependent anisotropy and is sensitive to the length scale of fractures. The model considers velocity dispersion and attenuation due to a squirt-flow mechanism at two different scales: the grain scale (microcracks and equant matrix porosity) and formation-scale fractures. The theory is first tested and calibrated against published laboratory data. Then we present the analysis and modelling of frequency-dependent shear-wave splitting in multicomponent VSP data from a tight gas reservoir. We invert for fracture density and fracture size from the frequency dependence of the time delay between split shear waves. The derived fracture length matches independent observations from borehole data.  相似文献   

16.
A model of wave propagation in fluid-saturated porous media is developed where the principal fluid/solid interaction mode affecting the propagation of the acoustic wave results from the conjunction of the Biot and the Squirt flow mechanism. The difference between the original Biot/Squirt (BISQ) flow theory and the new theory, which we call the reformulated BISQ, is that the average fluid pressure term appearing in the dynamic equation for a two component solid/fluid continuum is independent of squirt flow length. P-velocity and attenuation relate to measurable rock physical parameters: the Biot's poroelastic constants, porosity, permeability, pore fluid compressibility and viscosity. Modelling shows that velocity and attenuation dispersion obtained using the reformulated BISQ theory are of the same order of magnitude as those obtained using the original BISQ theory. Investigation on permeability effect on velocity and attenuation dispersion indicate that the transition zone in velocity and attenuation peak, occurring both at the relaxation frequency, shifts toward high frequency when permeability decreases. This behaviour agrees with Biot's theory prediction.  相似文献   

17.
Unlike light oils, heavy oils do not have a well‐established scheme for modelling elastic moduli from dynamic reservoir properties. One of the main challenges in the fluid substitution of heavy oils is their viscoelastic nature, which is controlled by temperature, pressure, and fluid composition. Here, we develop a framework for fluid substitution modelling that is reliable yet practical for a wide range of cold and thermal recovery scenarios in producing heavy oils and that takes into account the reservoir fluid composition, grounded on the effective‐medium theories for estimating elastic moduli of an oil–rock system. We investigate the effect of fluid composition variations on oil–rock elastic moduli with temperature changes. The fluid compositional behaviour is determined by flash calculations. Elastic moduli are then determined using the double‐porosity coherent potential approximation method and the calculated viscosity based on the fluid composition. An increase in temperature imposes two opposing mechanisms on the viscosity behaviour of a heavy‐oil sample: gas liberation, which tends to increase the viscosity, and melting, which decreases the viscosity. We demonstrate that melting dominates gas liberation, and as a result, the viscosity and, consequently, the shear modulus of the heavy oils always decrease with increasing temperature. Furthermore, it turns out that one can disregard the effects of gas in the solution when modelling the elastic moduli of heavy oils. Here, we compare oil–rock elastic moduli when the rock is saturated with fluids that have different viscosity levels. The objective is to characterize a unique relation between the temperature, the frequency, and the elastic moduli of an oil–rock system. We have proposed an approach that takes advantage of this relation to find the temperature and, consequently, the viscosity in different regions of the reservoir.  相似文献   

18.
Saturation of porous rocks with a mixture of two fluids (known as partial saturation) has a substantial effect on the seismic waves propagating through these rocks. In particular, partial saturation causes significant attenuation and dispersion of the propagating waves, due to wave-induced fluid flow. Such flow arises when a passing wave induces different fluid pressures in regions of rock saturated by different fluids. As partial fluid saturation can occur on different length scales, attenuation due to wave-induced fluid flow is ubiquitous. In particular, mesoscopic fluid flow due to heterogeneities occurring on a scale greater than porescale, but less than wavelength scale, is responsible for significant attenuation in the frequency range from 10 to 1000 Hz.Most models of attenuation and dispersion due to mesoscopic heterogeneities imply that fluid heterogeneities are distributed in a periodic/regular way. In 1D this corresponds to periodically alternating layering, in 3D as periodically distributed inclusions of a given shape (usually spheres). All these models yield very similar estimates of attenuation and dispersion.Experimental studies show that mesoscopic heterogeneities have less idealized distributions and that the distribution itself affects attenuation and dispersion. Therefore, theoretical models are required which would simulate the effect of more general and realistic fluid distributions.We have developed two theoretical models which simulate the effect of random distributions of mesoscopic fluid heterogeneities. The first model assumes that one fluid forms a random ensemble of spherical inclusions in a porous medium saturated by the other fluid. The attenuation and dispersion predicted by this model are very similar to those predicted for 3D periodic distribution. Attenuation (inverse quality factor) is proportional to ω at low frequencies for both distributions. This is in contrast to the 1D case, where random and periodically alternating layering shows different attenuation behaviour at low frequencies. The second model, which assumes a 3D continuous distribution of fluid heterogeneities, also predicts the same low-frequency asymptote of attenuation. However, the shapes of the frequency dependencies of attenuation are different. As the 3D continuous random approach assumes that there will be a distribution of different patch sizes, it is expected to be better suited to modelling experimental results. Further research is required in order to uncover how to relate the random functions to experimentally significant parameters.  相似文献   

19.
Fluid flow exerts a critical impact on the convection of thermal energy in geological media, whereas heat transport in turn affects fluid properties, including fluid dynamic viscosity and density. The interplay of flow and heat transport also affects solute transport. To unravel these complex coupled flow, heat, and solute transport processes, here, we present a theory for the idealized scale‐dependent Poiseuille flow model considering a constant temperature gradient (?T) along a single fracture, where fluid dynamic viscosity connects with temperature via an exponential function. The idealized scale‐dependent model is validated based on the solutions from direct numerical simulations. We find that the hydraulic conductivity (K) of the Poiseuille flow either increases or decreases with scales depending on ?T > 0°C/m or ?T < 0°C/m, respectively. Indeed, the degree of changes in K depends on the magnitude of ?T and fracture length. The scale‐dependent model provides an alternative explanation for the well‐known scale‐dependent transport problem, for example, the dispersion coefficient increases with travel distance when ?T > 0°C/m according to the Taylor dispersion theory, because K (or equivalently flux through fractures) scales with fracture length. The proposed theory unravels intertwined interactions between flow and transport processes, which might shed light on understanding many practical geophysical problems, for example, geothermal energy exploration.  相似文献   

20.
碳酸盐岩孔隙结构类型复杂多样,当地震波经过含有不同孔隙结构的流体饱和岩石后往往会产生不同的波频散和衰减特征,这使得根据波的不同响应特征来推断碳酸盐岩的孔隙结构类型,甚至孔隙流体性质信息成为可能.本文针对白云岩、灰岩以及人工碳酸盐岩样品开展了跨频段（超声+低频）实验测量和理论建模,探索碳酸盐岩的孔隙结构类型和孔隙流体对模量频散和衰减的影响机制.首先根据铸体薄片、扫描电镜的图像对碳酸盐岩样品进行了孔隙结构类型分析,并将样品主要分为裂缝型、裂缝-孔隙型、孔洞型三类,然后测量了相应样品完全饱和流体后在不同围压下的模量频散与衰减.在完全饱和甘油并处于低围压时,裂缝型与孔洞型样品均出现一个衰减峰,分别位于1 Hz与100 Hz附近,而裂缝-孔隙型样品则具有两个衰减峰,一个在1 Hz附近,另一个在100 Hz附近.裂缝型样品（裂缝主导）的衰减峰相比孔洞型样品（中等刚度孔隙主导）对应的衰减峰在低围压下幅度更大,且对围压变化更敏感.在测量数据的基础上,建立了考虑纵横比分布的软孔隙和中等刚度孔隙的喷射流模型,认为该模型能一定程度上解释裂缝型、裂缝-孔隙型、孔洞型三种类型碳酸盐岩在测量频带的频散.以上研究加深了对不同孔隙类型主导的碳酸盐岩储层地震响应特征的认识,对储层预测工作的进一步精细化具有重要意义.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号