首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 218 毫秒
1.
针对天地基联合测控中多源异质数据存在多耦合性系统模型误差和粗差的情况,提出了基于数据深度加权半参数估计的方差分量估计法.利用半参数估计法补偿不确定性模型误差,同时构建数据深度权抑制粗差的影响,使半参数估计不受粗差的影响,为方差分量估计提供合理的权矩阵,使得方差分量估计能对存在不确定性模型误差和粗差的结构定权.进行了天地基对空间目标的联合测控仿真试验.结果表明,改进的方差分量估计法能有效补偿不确定性模型误差并抑制粗差的影响,确定更加合理的权值.  相似文献   

2.
统计定轨中随机模型的验后估计   总被引:1,自引:0,他引:1  
在卫星精密定轨中,对资料的加权一般是采用经验的方法,本文采用赫尔默特(Helmert)方差分量估计方法,对Lageos2卫星6个月的SLR资料进行试算,统计了各台站的验后方差,结果表明,用验后方差估计的方法可以得到各台站大致合理的权重,而且可以检验参数配置的合理性。  相似文献   

3.
当测轨数据误差不服从正态分布时,传统的最小二乘(LSE)轨道确定方法将不是最优的.为了获得高精度的定轨结果,一种可行的策略是采用基于最小p范数(Lp)的轨道确定方法.通过分析Lp估计的相关性质,得出普通Lp估计不具有良好的抗差性的结论.为抑制模型误差和异常值的影响,提出了基于数据深度加权的稳健最小p范数估计方法,并证明了相关性质,得出了其崩溃点可以达到1/2的结论.最后,通过残差分析和矩估计法自适应估计相关参数,使得估计达到最大效率.以天基空间目标监视系统为背景进行了仿真试验.结果表明,当观测数据存在系统误差或异常值时,或者当目标动力学模型存在误差或者天基观测平台存在系统误差时,即使观测数据服从正态分布,LSE也不是最优的,在这种意义下自适应稳健Lp估计轨道确定方法比传统轨道确定方法更加稳健,定轨精度也更高.  相似文献   

4.
本文利用模拟观测资料,估计了中国卫星跟踪网对近地测地卫星定轨和测定一些跟踪站地心坐标所能达到的精度。同时分析了近地卫星定轨的主要误差源,如大气模型、地球引力场模型的不确定性和跟踪网站坐标的误差等所产生的影响。  相似文献   

5.
LP估计在星载GPS运动学定轨中的应用及精度分析   总被引:2,自引:0,他引:2  
为得到高精度的星载GPS运动学定轨,必须利用观测精度高的相位观测值,但是相位观测值预处理后,仍然存在残余小周跳.在残差服从正态分布情况下LS法是最佳参数解算方法,但该方法不能解决资料的系统误差消除问题,LP估计是处理资料残差分布含有系统误差的有效方法之一.基于LS、LP方法的有效条件和GPS数据预处理的特性,将LP估计方法引入星载GPS运动学定轨数据处理中,以CHAMP卫星资料为例,研究了LP估计在星载GPS运动学定轨中的应用及其精度分析.实践表明:在处理含有残余小周跳的相位观测值时,LP估计比LS更有效,提高了星载GPS运动学定轨精度,但随着残余周跳的进一步修复,LP估计相对于LS估计的优越性越来越弱,在资料完全没有系统误差,残差服从正态分布的情况下,LP估计不能很好地体现其优越性,精度反而低于LS估计.  相似文献   

6.
抗差估计在星载GPS卫星非差运动学定轨中的应用   总被引:1,自引:0,他引:1  
吴江飞  黄珹 《天文学报》2006,47(3):320-327
针对星载GPS卫星非差运动学定轨的特点,提出将抗差估计应用于星载GPS卫星运动学定轨,一方面尽量保留来自每颗GPS卫星的观测值,保持较强的卫星几何强度,避免轨道求解出现奇异;另一方面,采用等价权思想,有效地降低质量较差的观测值对定轨结果的影响,保证定轨精度.还采用CHAMP卫星的实测GPS数据验证了新方案的可行性和有效性.  相似文献   

7.
两种观测技术综合精密定轨的探讨   总被引:8,自引:0,他引:8  
张强  廖新浩  黄珹 《天文学报》2000,41(4):347-354
利用T/P卫星的SLR和DORIS实测资料,对两种观测技术综合精密定轨中的加权及其对定轨影响的问题作了初步的探讨。根据所提出的一种经验性的加权方法进行了综合定轨计算,结果表明:对于两种不同技术的观测,相对权选取的恰当与否将影响综合定轨的精度;综合定轨的最优加权不仅依赖于观测资料的精度,还与观测资料的多少和几何分布有关;通过选用最优加权,可使得综合轨的精度优于仅用其中一种技术的定轨精度,综合定轨能有效地提高定轨精度。  相似文献   

8.
主要介绍了对一种特殊观测类型(双星定位系统中)的几何定轨方法,该方法将观测中遇到的超越方程组简化成一个线性方程组和一个一元二次方程,然后进行解算,通过一个模拟的双星系统和一组模拟的观测值进行试算的结果表明,如果无测量误差时,对该系统用几何方法定轨的精度可以好于2m,但是当该系统的几何图形较差时,几何定轨方法对测量误差较为敏感,若测量的随机误差为10m,则定轨坐标分量的误差最大可达到400m。这时可利用三阶契比雪夫多项式平滑的方法削弱随拳影响,将几何方法定轨的精度提高到40m。  相似文献   

9.
将方差分量估计(VCE)方法应用于ERS-2卫星的精密定轨,用SLR和PRARE资料计算了1998年前3个月的23个长度为5天的弧段(除了调整轨道的时段外,相邻弧段有两天的重叠),从观测值残差分析和重叠弧段比较两个方面,考察VCE方法对定轨计算的影响,并给出了各组观测值的平均验后均方差,对观测值残差的分析表明,使用VCE方法明显地改善了观测值的拟合程度,但从阿卑(Abbey)标准对观测值残差的检验结果来看,使用VCE方法不能消除轨道中由力学模型和几何模型误差引入的系统差,重叠弧段比较的结果表明:(1)使用VCE方法缩小了重叠弧段的平均距离差,并改善了一部分权段明显不合理的偏离,使最后得到的轨道具有更均匀的精度,(2)相比较而言,VCE方法使相邻弧段靠拢的趋势在轨道切向体现得较为明显,由各组观测值的平均验后方差可见,说单个标准点观测值而言,部分SLR台站的观测资料在定轨计算中占有比其他观测资料更重的地位,纵观全文,使用VCE后得到的观测值的平衡验后均方差来确定资料的双重将比使用均方差更为合理。  相似文献   

10.
卫星动力学模型误差是客观存在的事实,动力学模型误差传递到轨道确定算法中构成部分形式未知的模型误差,并且与测量系统自身的系统误差和随机误差耦合在一起形成定轨模型误差,严重影响轨道确定精度.详细推导了存在动力学模型误差的轨道改进方程,对模型中能准确描述的部分建立了参数化模型,对不能准确描述的误差部分,建立了非参数模型.构建了部分线性轨道改进模型,利用二阶段估计法和核函数估计法对模型误差进行拟合估计,并在轨道改进中予以补偿.根据数据深度理论,建立了非参数模型误差的深度加权核估计方法,提高了模型误差估计的抗差性.最后结合天基空间目标监视系统进行了轨道确定仿真实验.实验结果表明,模型误差是影响轨道确定精度的重要因素,核函数估计法可以有效估计定轨中的模型误差,窗宽是提高模型估计精度的重要变量,通过深度加权处理可以明显提高核函数估计的抗差性,提高轨道确定精度.  相似文献   

11.
Laura Schaefer 《Icarus》2004,169(1):216-241
We modified the MAGMA chemical equilibrium code developed by Fegley and Cameron (1987, Earth Planet. Sci. Lett. 82, 207-222) and used it to model vaporization of high temperature silicate lavas on Io. The MAGMA code computes chemical equilibria in a melt, between melt and its equilibrium vapor, and in the gas phase. The good agreement of MAGMA code results with experimental data and with other computer codes is demonstrated. The temperature-dependent pressure and composition of vapor in equilibrium with lava is calculated from 1700 to 2400 K for 109 different silicate lavas in the ONaKFeSiMgCaAlTi system. Results for five lavas (tholeiitic basalt, alkali basalt, Barberton komatiite, dunite, and a molten type B1 Ca, Al-rich inclusion) are discussed in detail. The effects of continuous fractional vaporization on chemistry of these lavas and their equilibrium vapor are presented. The predicted abundances (relative to Na) of K, Fe, Si, Al, Ca, and Ti in the vapor equilibrated with lavas at 1900 K are lower than published upper limits for Io's atmosphere (which do not include Mg). We predict evaporative loss of alkalis, Fe, and Si during volcanic eruptions. Sodium is more volatile than K, and the Na/K ratio in the gas is decreased by fractional vaporization. This process can match Io's atmospheric Na/K ratio of 10±3 reported by Brown (2001, Icarus 151, 190-195). Silicon monoxide is an abundant species in the vapor above lavas. Spectroscopic searches are recommended for SiO at IR and mm wavelengths. Reactions of metallic vapors with S- and Cl-bearing volcanic gases may form other unusual gases including MgCl2, MgS, MgCl, FeCl2, FeS, FeCl, and SiS.  相似文献   

12.
正Research in Astronomy and Astrophysics publishes original research papers and reviews 011 all liranchcs of astronoiriy and astrophysics.Reviews arc by invitation only.Important new results that require rapid publication can be submitted as a Letter(Letters must be restricted in length  相似文献   

13.
14.
正Research in Astronomy and Astrophysics publishes original research papers and reviews on all branches of astronomy and astrophysics.Reviews are by invitation only.Important new results that require rapid publication can be submitted as a Letter(Letters must be restricted in length to 6 printed pages).Authors who submit a paper are expected to be able to certify that the paper is original work,  相似文献   

15.
16.
Laura Schaefer 《Icarus》2005,173(2):454-468
We use chemical equilibrium calculations to model the speciation of alkalis and halogens in volcanic gases emitted on Io. The calculations cover wide temperature (500-2000 K) and pressure (10−6 to 10+1 bars) ranges, which overlap the nominal conditions at Pele (T=1760 K, P=0.01 bars). About 230 compounds of 11 elements (O, S, Li, Na, K, Rb, Cs, F, Cl, Br, I) are considered. The elemental abundances for O, S, Na, K, and Cl are based upon observations. CI chondritic elemental abundances relative to sulfur are used for the other alkalis and halogens (as yet unobserved on Io). We predict the major alkali species in Pele-like volcanic gases and the percentage distribution of each alkali are LiCl (73%), LiF (27%); NaCl (81%), Na (16%), NaF (3%); KCl (91%), K (5%), KF (4%); RbCl (93%), Rb (4%), RbF (3%); CsCl (92%), CsF (6%), Cs (2%). Likewise the major halogen species and the percentage distribution of each halogen are NaF (88%), KF (10%), LiF (2%); NaCl (89%), KCl (11%); NaBr (89%), KBr (10%), Br (1%); NaI (61%), I (30%), KI (9%). We predict the major halogen condensates and their condensation temperatures at P=0.01 bar are NaF (1115 K), LiF (970 K); NaCl (1050 K), KCl (950 K); KBr (750 K), RbBr (730 K), CsBr (645 K); and solid I2 (200 K). We also model disequilibrium chemistry of the alkalis and halogens in the volcanic plume. Based on this work and our prior modeling for Na, K, and Cl in a volcanic plume, we predict the major loss processes for the alkali halide gases are photolysis and/or condensation onto grains. Their estimated photochemical lifetimes range from a few minutes for alkali iodides to a few hours for alkali fluorides. Condensation is apparently the only loss process for elemental iodine. On the basis of elemental abundances and photochemical lifetimes, we recommend searching for gaseous KCl, NaF, LiF, LiCl, RbF, RbCl, CsF, and CsCl around volcanic vents during eruptions. Based on abundance considerations and observations of brown dwarfs we also recommend a search of Io's extended atmosphere and the Io plasma torus for neutral and ionized Li, Cs, Rb, and F.  相似文献   

17.
18.
A special stressed annular polishing technique is proposed to mill the off-axis aspheric sub-mirrors of a large segmented mirror with an annular polishing machine. Based on the basic principle of stressed annular polishing technique, a set of special stressing mechanisms are designed to convert milling the aspheric surfaces of sub-mirrors with different off-axis distances into milling the spherical surfaces with identical radii of curvature, so that they can be pol- ished simultaneously on a continuous polishing machine. It took about contin- uous 40 hours to polish a scaled-down mirror of the planning Chinese Future Giant Telescope (CFGT) using this technique. This mirror has the 330 mm di- ameter, 3.6 m off-axis distance, and the 21.6 m radius of curvature, and its max- imum asphericity is 16 micron. The experiment shows that this method has a high effciency, suits batch manufacturing, especially the batch manufacturing of aspheric sub-mirrors of the segmented primary mirror of an extremely large aperture telescope.  相似文献   

19.
In this paper, we investigate the dynamics of Born–Infeld (B–I) phantom model in the ωω′ plane, which is defined by the equation of state parameter for the dark energy and its derivative with respect to N (the logarithm of the scale factor a). We find the scalar field equation of motion in ωω′ plane, and show mathematically the property of attractor solutions which correspond to ω φ ∼−1, Ω φ =1, which avoid the “Big rip” problem and meets the current observations well.   相似文献   

20.
In astronomical observations at optical wavelengths, a fast image tracking system can be adopted to reduce the effects of the atmospheric seeing and telescopic tracking error, and therefore improve the observing efficiency. Aiming at the need of astronomical observations, totally 5 kinds of algorithms in two categories were selected to make a comparative study on their accuracies and stabilities under different noise conditions by both numerical experiment and laboratory test. The results indicate that the normalized cross-correlation method and barycenter method have not only a higher accuracy but also a better reliability against interferences, they will be applied to the high-resolution spectrograph of the Xinglong 2.16 m telescope and the scienti?c instruments of the SONG (Stellar Observations Network Group) project, respectively.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号