首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 359 毫秒
1.
Heat is a powerful tracer to quantify fluid exchange between surface water and groundwater. Temperature time series can be used to estimate pore water fluid flux, and techniques can be employed to extend these estimates to produce detailed plan‐view flux maps. Key advantages of heat tracing include cost‐effective sensors and ease of data collection and interpretation, without the need for expensive and time‐consuming laboratory analyses or induced tracers. While the collection of temperature data in saturated sediments is relatively straightforward, several factors influence the reliability of flux estimates that are based on time series analysis (diurnal signals) of recorded temperatures. Sensor resolution and deployment are particularly important in obtaining robust flux estimates in upwelling conditions. Also, processing temperature time series data involves a sequence of complex steps, including filtering temperature signals, selection of appropriate thermal parameters, and selection of the optimal analytical solution for modeling. This review provides a synthesis of heat tracing using diurnal temperature oscillations, including details on optimal sensor selection and deployment, data processing, model parameterization, and an overview of computing tools available. Recent advances in diurnal temperature methods also provide the opportunity to determine local saturated thermal diffusivity, which can improve the accuracy of fluid flux modeling and sensor spacing, which is related to streambed scour and deposition. These parameters can also be used to determine the reliability of flux estimates from the use of heat as a tracer.  相似文献   

2.
The delineation of groundwater discharge areas based on Distributed Temperature Sensing (DTS) data of the streambed can be difficult in soft‐bedded streams where sedimentation and scouring processes constantly change the position of the fibre optic cable relative to the streambed. Deposition‐induced temperature anomalies resemble the signal of groundwater discharge while scouring will cause the cable to float in the water column and measure stream water temperatures. DTS applied in a looped layout with nine fibre optic cable rows in a 70 × 5 m section of a soft‐bedded stream made it possible to detect variability in streambed temperatures between October 2011 and January 2012. Detailed monthly streambed elevation surveys were carried out to monitor the position of the fibre optic cable relative to the streambed and to quantify the effect of sedimentation processes on streambed temperatures. Based on the simultaneous interpretation of streambed temperature and elevation data, a method is proposed to delineate potential high‐groundwater discharge areas and identify deposition‐induced temperature anomalies in soft‐bedded streams. Potential high‐discharge sites were detected using as metrics the daily minimum, maximum and mean streambed temperatures as well as the daily amplitude and standard deviation of temperatures. The identified potential high‐discharge areas were mostly located near the channel banks, also showing temporal variability because of the scouring and redistribution of streambed sediments, leading to the relocation of pool‐riffle sequences. This study also shows that sediment deposits of 0.1 m thickness already resulted in an increase in daily minimum streambed temperatures and decrease in daily amplitude and standard deviation. Scouring sites showed lower daily minimum streambed temperatures and higher daily amplitude and standard deviation compared with areas without sedimentation and scouring. As a limitation of the approach, groundwater discharge occurring at depositional and scouring areas cannot be identified by the metrics applied. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

3.
In the past few years, distributed acoustic sensing has gained great interest in geophysics. This acquisition technology offers immense improvement in terms of efficiency when compared with current geophysical acquisition methods. However, the fundamentals of the measurement are still not fully understood because direct comparisons of fibre data with conventional geophysical sensors are difficult during field tests. We present downscaled laboratory experiments that enabled us to characterise the relationship between the signals recorded by conventional seismic point receivers and by distributed fibre optic sensors. Interrogation of the distributed optical fibre sensor was performed with a Michelson interferometer because this system is suited to compact test configurations, and it requires only a very simple data processing workflow for extracting the signal outputs. We show acoustic data that were recorded simultaneously by both the fibre optical interferometer and conventional three‐component accelerometers, thus enabling the comparison of sensor performance. We present results focused on the directionality of fibre measurements, on the amplitude variation with angle of incidence, and on the transfer function that allows accelerometer signals to be transformed into optical fibre signals. We conclude that the optical fibre response matches with the array of the displacement differences of the inline accelerometers deployed along the fibre length. Moreover, we also analysed the influence of various types of coupling and fibre cable coating on the signal responses, emphasising the importance of these parameters for field seismic acquisitions when using the distributed fibre optic technology.  相似文献   

4.
There are several methods for determining the spatial distribution and magnitude of groundwater inputs to streams. We compared the results of conventional methods [dye dilution gauging, acoustic Doppler velocimeter (ADV) differential gauging, and geochemical end‐member mixing] to distributed temperature sensing (DTS) using a fibre‐optic cable installed along 900 m of Ninemile Creek in Syracuse, New York, USA, during low‐flow conditions (discharge of 1·4 m3 s?1). With the exception of differential gauging, all methods identified a focused, contaminated groundwater inflow and produced similar groundwater discharge estimates for that point, with a mean of 66·8 l s?1 between all methods although the precision of these estimates varied. ADV discharge measurement accuracy was reduced by non‐ideal conditions and failed to identify, much less quantify, the modest groundwater input, which was only 5% of total stream flow. These results indicate ambient tracers, such as heat and geochemical mixing, can yield spatially and quantitatively refined estimates of relatively modest groundwater inflow even in large rivers. DTS heat tracing, in particular, provided the finest spatial characterization of groundwater inflow, and may be more universally applicable than geochemical methods, for which a distinct and consistent groundwater end member may be more difficult to identify. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

5.
The hyporheic zone (HZ) has the capability to eliminate and attenuate nutrients and contaminants in riverine systems. Biogeochemical reactions and the potential elimination of contaminants are strongly controlled by the flow paths and dynamics in the HZ. Nevertheless, an easily applicable method for the field determination of flow patterns in the HZ is still lacking. Therefore, a heat pulse technique, which traces the movement of a short heat pulse in the upper part of the HZ and other sand beds, was developed. Five rods are vertically driven into the sediment of the streambed; one rod with a heater as point source located in about 10‐cm sediment depth and four rods with four temperature sensors in 3 cm distance, arranged concentrically with 7 cm diameter around the heating rod. Subsequently, a heat pulse is applied and the resulting breakthrough curves are indicative of flow velocities and flow directions in the streambed. A rough data analysis procedure is also suggested. In addition, laboratory experiments were performed to test the heat pulse technique. These experiments were validated based on coupled numerical modelling of flow and heat transport. First field tests of the method prove that the method is easily applicable under field conditions. These first field tests showed highly complex flow patterns with flow velocities from 1·8 to 4·9 cm min?1 and flow directions from parallel to surface flow to opposite to surface flow. This suggests the need for a robust method to quantify hyporheic flow patterns in situ. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

6.
Distributed vibration sensing, also known as distributed acoustic sensing, is a relatively new method for recording vertical seismic profile data using a fibre optic cable as the sensor. The signal obtained from such systems is a distributed measurement over a length of fibre referred to as the gauge length. In this paper, we show that gauge length selection is one of the most important acquisition parameters for a distributed vibration sensing survey. If the gauge length is too small, then the signal‐to‐noise ratio will be poor. If the gauge length is too large, resolution will be reduced and the shape of the wavelet will be distorted. The optimum gauge length, as derived here, is a function of the velocity and frequencies of the seismic waves being measured. If these attributes vary considerably over the depth of a survey, then the use of different gauge lengths is recommended. The significant increases in data quality resulting from the use of multiple gauge length values are demonstrated using field data.  相似文献   

7.
The question: ‘how does a streambed change over a minor flood?’ does not have a clear answer due to lack of measurement methods during high flows. We investigate bedload transport and disentrainment during a 1.5‐year flood by linking field measurements using fiber optic distributed temperature sensing (DTS) cable with sediment transport theory and an existing explicit analytical solution to predict depth of sediment deposition from amplitude and phase changes of the diurnal near‐bed pore‐water temperature. The method facilitates the study of gravel transport by using near‐bed temperature time series to estimate rates of sediment deposition continuously over the duration of a high flow event coinciding with bar formation. The observations indicate that all gravel and cobble particles present were transported along the riffle at a relatively low Shields Number for the median particle size, and were re‐deposited on the lee side of the bar at rates that varied over time during a constant flow. Approximately 1–6% of the bed was predicted to be mobile during the 1.5‐year flood, indicating that large inactive regions of the bed, particularly between riffles, persist between years despite field observations of narrow zones of local transport and bar growth on the order ~3–5 times the median particle size. In contrast, during a seven‐year flood approximately 8–55% of the bed was predicted to become mobile, indicating that the continuous along‐stream mobility required to mobilize coarse gravel through long pools and downstream to the next riffle is infrequent. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

8.
An understanding of the spatial and hydraulic properties of fast preferential flow pathways in the subsurface is necessary in applications ranging from contaminant fate and transport modeling to design of energy extraction systems. One method for the characterization of fracture properties over interwellbore scales is Multiperiod Oscillatory Hydraulic (MOH) testing, in which the aquifer response to oscillatory pressure stimulations is observed. MOH tests were conducted on isolated intervals of wells in siliciclastic and carbonate aquifers in southern Wisconsin. The goal was to characterize the spatial properties of discrete fractures over interwellbore scales. MOH tests were conducted on two discrete fractured intervals intersecting two boreholes at one field site, and a nest of three piezometers at another field site. Fracture diffusivity estimates were obtained using analytical solutions that relate diffusivity to observed phase lag and amplitude decay. In addition, MOH tests were used to investigate the spatial extent of flow using different conceptual models of fracture geometry. Results indicated that fracture geometry at both field sites can be approximated by permeable two‐dimensional fracture planes, oriented near‐horizontally at one site, and near‐vertically at the other. The technique used on MOH field data to characterize fracture geometry shows promise in revealing fracture network characteristics important to groundwater flow and transport.  相似文献   

9.
3D multivalued travel time and amplitude maps   总被引：2，自引：0，他引：2  
An algorithm for computing multivalued maps for travel time, amplitude and any other ray related variable in 3D smooth velocity models is presented. It is based on the construction of successive isochrons by tracing a uniformly dense discrete set of rays by fixed travel-time steps. Ray tracing is based on Hamiltonian formulation and includes computation of paraxial matrices. A ray density criterion ensures uniform ray density along isochrons over the entire ray field including caustics. Applications to complex models are shown.  相似文献   

10.
Knowledge on groundwater–surface water interaction and especially on exchange fluxes between streams and aquifers is an important prerequisite for the study of transport and fate of contaminants and nutrients in the hyporheic zone. One possibility to quantify groundwater–surface water exchange fluxes is by using heat as an environmlental tracer. Modern field equipment including multilevel temperature sticks and the novel open‐source analysis tool LPML make this technique ever more attractive. The recently developed LPML method solves the one‐dimensional fluid flow and heat transport equation by combining a local polynomial method with a maximum likelihood estimator. In this study, we apply the LPML method on field data to quantify the spatial and temporal variability of vertical fluxes and their uncertainties from temperature–time series measured in a Belgian lowland stream. Over several months, temperature data were collected with multilevel temperature sticks at the streambed top and at six depths for a small stream section. Long‐term estimates show a range from gaining fluxes of ?291 mm day?1 to loosing fluxes of 12 mm day?1; average seasonal fluxes ranged from ?138 mm day?1 in winter to ?16 mm day?1 in summer. With our analyses, we could determine a high spatial and temporal variability of vertical exchange fluxes for the investigated stream section. Such spatial and temporal variability should be taken into account in biogeochemical cycling of carbon, nutrients and metals and in fate analysis of contaminant plumes. In general, the stream section was gaining during most of the observation period. Two short‐term high stream stage events, seemingly caused by blockage of the stream outlet, led to a change in flow direction from gaining to losing conditions. We also found more discharge occurring at the outer stream bank than at the inner one indicating a local flow‐through system. With the conducted analyses, we were able to advance our understanding of the regional groundwater flow system. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

11.
A modular borehole monitoring concept has been implemented to provide a suite of well‐based monitoring tools that can be deployed cost effectively in a flexible and robust package. The initial modular borehole monitoring system was deployed as part of a CO2 injection test operated by the Southeast Regional Carbon Sequestration Partnership near Citronelle, Alabama. The Citronelle modular monitoring system transmits electrical power and signals, fibre‐optic light pulses, and fluids between the surface and a reservoir. Additionally, a separate multi‐conductor tubing‐encapsulated line was used for borehole geophones, including a specialized clamp for casing clamping with tubing deployment. The deployment of geophones and fibre‐optic cables allowed comparison testing of distributed acoustic sensing. We designed a large source effort (>64 sweeps per source point) to test fibre‐optic vertical seismic profile and acquired data in 2013. The native measurement in the specific distributed acoustic sensing unit used (an iDAS from Silixa Ltd) is described as a localized strain rate. Following a processing flow of adaptive noise reduction and rebalancing the signal to dimensionless strain, improvement from repeated stacking of the source was observed. Conversion of the rebalanced strain signal to equivalent velocity units, via a scaling by local apparent velocity, allows quantitative comparison of distributed acoustic sensing and geophone data in units of velocity. We see a very good match of uncorrelated time series in both amplitude and phase, demonstrating that velocity‐converted distributed acoustic sensing data can be analyzed equivalent to vertical geophones. We show that distributed acoustic sensing data, when averaged over an interval comparable to typical geophone spacing, can obtain signal‐to‐noise ratios of 18 dB to 24 dB below clamped geophones, a result that is variable with noise spectral amplitude because the noise characteristics are not identical. With vertical seismic profile processing, we demonstrate the effectiveness of downgoing deconvolution from the large spatial sampling of distributed acoustic sensing data, along with improved upgoing reflection quality. We conclude that the extra source effort currently needed for tubing‐deployed distributed acoustic sensing vertical seismic profile, as part of a modular monitoring system, is well compensated by the extra spatial sampling and lower deployment cost as compared with conventional borehole geophones.  相似文献   

12.
Temperature measurements have been used by a variety of researchers to gain insight into groundwater discharge patterns. However, much of this research has reduced the problem to heat and fluid flow in one dimension for ease of analysis. This approach is seemingly at odds with the goal of determining spatial variability in specific discharge, which implies that the temperature field will vary in more than one dimension. However, it is unclear how important the resulting discrepancies are in the context of determining groundwater discharge to surface water bodies. In this study, the importance of these variations is examined by testing two popular one‐dimensional analytical solutions with stochastic models of heat and fluid flow in a two‐dimensional porous medium. For cases with low degrees of heterogeneity in hydraulic conductivity, acceptable results are possible for specific discharges between 10?7 and 10?5 m/s. However, conduction into areas with specific discharges less than 10?7 m/s from adjacent areas can lead to significant errors. In some of these cases, the one‐dimensional solutions produced estimates of specific discharge of nearly 10?6 m/s. This phenomenon is more likely in situations with greater degrees of heterogeneity.  相似文献   

13.
The concept of distributed strain‐sensing techniques has been proposed in our recent research, which was dedicated to utilizing the strain distributions throughout the full or partial areas of structures to detect arbitrary and unforeseen damage. An algorithm not requiring a detailed analytical model is presented for damage locating in flexural structures through the direct use of dynamic responses recorded by distributed long‐gauge strain sensors. The modal macro‐strain vector (MMSV), which has been proven to have a mapping relation with displacement mode shape, can be extracted directly from macro‐strain time‐series data, from which a damage evaluating index can be derived and used as an indicator for locating damage. Numerical examples are simulated to verify the sensitivity and effectiveness of the index in different cases. Furthermore, experimental investigations on a cantilevered beam with various long‐gauge fibre optic sensors placements are carried out to examine the feasibility and applicability of the proposed method. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

14.
Heat tracing methods have been widely employed for subsurface characterization. Nevertheless, there were very few studies regarding the optimal monitoring design for heat tracing in heterogeneous streambeds. In this study, we addressed this issue by proposing an efficient optimal design framework to collect the most informative diurnal temperature signal for Bayesian estimation of streambed hydraulic conductivities. The data worth (DW) was measured by the expected relative entropy between the prior and posterior distributions of the conductivity field. An adaptively refined Gaussian process surrogate was employed to alleviate the computational burden, resulting in at least three orders of magnitude of speed-up. The applicability of the optimal experimental design framework was evaluated by both numerical and sandbox experimental cases. Results showed that the most informative locations centered in the transition zones among the main patterns of the hydraulic conductivity field, while the most informative times centered in a short period after the minimum/maximum temperature appeared. With the fixed number of measurements, extending the calibration period was more beneficial than increasing the monitoring frequency in improving the estimation results. To our best knowledge, this work is the first study on Bayesian monitoring design for streambed characterization with the heat tracing method. The method and results can provide guidance on selecting monitoring strategies under budget-limited conditions.  相似文献   

15.
Recent research has demonstrated the use of in‐well heat tracer tests monitored by a fiber optic distributed temperature sensing (DTS) system to characterize borehole flow conditions in open bedrock boreholes. However, the accuracy of borehole flow rates determined from in‐well heat tracer tests has not been evaluated. The purpose of the research presented here is to determine whether borehole flow rates obtained using DTS‐monitored in‐well heat tracer tests are reasonable, and to evaluate the range of flow rates measureable with this method. To accomplish this, borehole flow rates measured using in‐well heat tracer tests are compared to borehole flow rates measured in the same boreholes using an impeller or heat pulse flowmeter. A comparison of flow rates measured using in‐well heat tracer tests to flow rates measured with an impeller flowmeter under the same conditions showed good agreement. A comparison of in‐well heat tracer test flow rate measurements to previously‐collected heat pulse flowmeter measurements indicates that the heat tracer test results produced borehole flow rates and flow profiles similar to those measured with the heat pulse flowmeter. The results of this study indicate that borehole flow rates determined from DTS‐monitored in‐well heat tracer tests are reasonable estimates of actual borehole flow rates. In addition, the range of borehole flow rates measurable by in‐well heat tracer tests spans from less than 10?1 m/min to approximately 101 m/min, overlapping the ranges typically measurable with an impeller flowmeter or a heat pulse flowmeter, making in‐well heat tracer testing a versatile borehole flow logging tool.  相似文献   

16.
Distributed acoustic sensing is an emerging technology using fibre‐optic cables to detect acoustic disturbances such as flow noise and seismic signals. The technology has been applied successfully in hydraulic fracture monitoring and vertical seismic profiling. One of the limitations of distributed acoustic sensing for seismic recording is that the conventional straight fibres do not have broadside sensitivity and therefore cannot be used in configurations where the raypaths are essentially orthogonal to the fibre‐optic cable, such as seismic reflection methods from the surface. The helically wound cable was designed to have broadside sensitivity. In this paper, a field trial is described to validate in a qualitative sense the theoretically predicted angle‐dependent response of a helically wound cable. P‐waves were measured with a helically wound cable as a function of the angle of incidence in a shallow horizontal borehole and compared with measurements with a co‐located streamer. The results show a similar behaviour as a function of the angle of incidence as the theory. This demonstrates the possibility of using distributed acoustic sensing with a helically wound cable as a seismic detection system with a horizontal cable near the surface. The helically wound cable does not have any active parts and can be made as a slim cable with a diameter of a few centimetres. For that reason, distributed acoustic sensing with a helically wound cable is a potential low‐cost option for permanent seismic monitoring on land.  相似文献   

17.
A two-dimensional walkaway vertical seismic profiling survey using distributed acoustic sensing was conducted at an onshore site in Japan. The maximum depth and the deviation of the observation well were more than 4,000 m and 81 degrees, respectively. Among the several methods for installing fibre optic cables, we adopted the inside coiled tubing method, in which coiled tubing containing a fibre optic cable is deployed. The signal-to-noise ratio of the raw shot gather was low, possibly due to poor coupling between the fibre optic cable and the subsurface formation resulting from the fibre optic cable deployment method and the existence of considerable tubewave noise. Nevertheless, direct P-wave arrivals, P–P reflections and P–S converted waves exhibited acceptable signal-to-noise ratios after careful optimization of gauge length for distributed acoustic sensing optical processing and the application of carefully parameterized tubewave noise suppression. One of the challenges in current distributed acoustic sensing vertical seismic profile data processing is the separation of P- and S-waves using only one-component measurements. Hence, we applied moveout correction using two-dimensional ray tracing. This process effectively highlights only reflected P-waves, which are used in subsequent subsurface imaging. Comparison with synthetic well seismograms and two-dimensional surface seismic data confirms that the final imaging result has a sufficiently high quality for subsurface monitoring. We acquired distributed acoustic sensing vertical seismic profile data under both flowing conditions and closed conditions, in which the well was shut off and no fluid flow was allowed. The two imaging results are comparable and suggest the possibility of subsurface imaging and time-lapse monitoring using data acquired under flowing conditions. The results of this study suggest that, by adopting the inside coiled tubing method without drilling a new observation well, more affordable distributed acoustic sensing vertical seismic profile monitoring can be achieved in fields such as CO2 capture and storage and unconventional shale projects, where monitoring costs have to be minimized.  相似文献   

18.
Groundwater interacts with surface water features nearly in all types of landscapes. Understanding these interactions has practical consequences on the quantity and quality of water in either system, because the depletion or contamination of one of the systems will eventually affect the other one. Many studies have shown that the use of heat as natural tracer in conjunction with water level measurements is an effective method for estimating water flow (fluxes) between groundwater and surface water. A number of studies have explored the effects of spatial and temporal variability of groundwater–surface water flux exchanges using temperature and water level measurements; however, the effect of temporal resolution of water level and temperature data on estimating flux remains unexplored. Therefore, this study investigated the effect of temporal resolution of input data on temporal variation of groundwater–surface water flux exchanges. To this end, we calibrated a variably saturated two‐dimensional groundwater flow and heat transport model (VS2DH) at hourly and daily time scales using temperatures measured at multiple depths below the riverbed of the Zenne River, located at a well‐known Belgian brownfield site. Results of the study showed that the computed water flux through the streambed ranged between ?32 mm/day and +25 mm/day using the hourly model and from ?10 mm/day to ?37 mm/day using the daily model. The hourly model resulted in detecting reversal of flow direction inducing short‐term surface water flow into the streambed. However, such events were not captured if daily temperature and water level measurements were used as input. These findings have important implications for understanding contaminant mass flux and their attenuation in the mixing zone of groundwater and surface water. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

19.
Analytical solutions for contaminant transport in a non‐uniform flow filed are very difficult and relatively rare in subsurface hydrology. The difficulty is because of the fact that velocity vector in the non‐uniform flow field is space‐dependent rather than constant. In this study, an analytical model is presented for describing the three‐dimensional contaminant transport from an area source in a radial flow field which is a simplest case of the non‐uniform flow. The development of the analytical model is achieved by coupling the power series technique, the Laplace transform and the two finite Fourier cosine transform. The developed analytical model is examined by comparing with the Laplace transform finite difference (LTFD) solution. Excellent agreements between the developed analytical model and the numerical model certificate the accuracy of the developed model. The developed model can evaluate solution for Peclet number up to 100. Moreover, the mathematical behaviours of the developed solution are also studied. More specifically, a hypothetical convergent flow tracer test is considered as an illustrative example to demonstrate the three‐dimensional concentration distribution in a radial flow field. The developed model can serve as benchmark to check the more comprehensive three‐dimensional numerical solutions describing non‐uniform flow contaminant transport. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

20.
Unlike conventional sensors that measure the passage of seismic waves at a single position, distributed vibration sensing systems, also known as distributed acoustic sensing systems, detect the passage of seismic waves by averaging a measurement of strain over a section of fibre‐optic cable. Distributed vibration sensing systems work by transmitting pulses of light down the fibre and measuring the phase of the Rayleigh backscatter. At random positions along the fibre, however, fading occurs; this is where the amplitude of the backscattered signal is very small due to cancellation of the scattered electric fields, resulting in anomalously noisy traces in a common source gather. This paper addresses the problem of fading in a particular form of distributed vibration sensors: a new optical arrangement of the instrumentation is described that allows the measurement to be carried out quasi‐simultaneously at multiple optical interrogation frequencies. The interrogation frequencies are chosen to be sufficiently different that their fading properties are distinct and the diversity thus obtained is used to aggregate the data obtained to substantially reduce the noise caused by fading. As well as reducing the effects of fading, the aggregation of the independent results can also help to reduce the overall noise of the measurement and improve the linearity of the distributed vibration sensing system.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号