共查询到20条相似文献，搜索用时 437 毫秒
1.
2.
针对地震槽波在低速层的传播特性,开展了煤层内地震槽波勘探的数值模拟和物理模拟研究的初探工作.在数值模拟研究方面,采用交错网格有限差分法对煤层中的地震槽波进行三分量全波场模拟.基于波场快照和人工合成地震记录研究了不同模型中的波场特征和各种波型的传播规律.在物理模拟方面,通过选用不同配比的环氧树脂和硅橡胶类材料构建地震槽波物理模型,利用透射法和反射法观测系统获得了清晰的地震槽波记录以研究槽波的地震学特征.研究表明,在煤层内槽波的地震波场中,Love型槽波的能量小于Rayleigh型槽波的SV分量,大于Rayleigh型槽波的SH分量.相对于Love型槽波和Rayleigh型槽波的SH分量,Rayleigh型槽波的SV分量在围岩中的泄露能量较强.在煤层界面附近的围岩中,地震波仍以槽波形式传播,随着距离的增加能量逐渐衰减.随着煤层变薄,煤层槽波主频向高频方向移动,频散现象增强,传播速度增大. 相似文献
3.
S. N. Bhattacharya 《Journal of Seismology》2018,22(5):1325-1334
We consider a transversely isotropic medium with vertical axis of symmetry (VTI). Rayleigh wave displacement components in a homogeneous VTI medium contain exp(±krjz), where z is the vertical coordinate, k is the wave number, and j?=?1, 2; rj may be considered as depth-decay factor. In a VTI medium, rj can be a real or imaginary as in an isotropic medium, or it can be a complex depending on the elastic parameters of the VTI medium; if complex, r1 and r2 are complex conjugates. In a homogeneous VTI half space, Rayleigh wave displacement is significantly modified with a phase shift when rj changes from real to complex with variation of VTI parameters; at the transition, the displacement becomes zero when r1?=?r2. In a liquid layer over a VTI half space, Rayleigh waves are dispersive. Here, also Rayleigh wave displacement significantly modified with a phase shift when rj changes from real to complex with a decrease of period. At very low period, phase velocity of Rayleigh waves becomes less than P-wave velocity in the liquid layer giving rise to Scholte waves (interface waves). The amplitudes of Scholte waves with a VTI half space are found to be significantly larger than those with an isotropic half space. 相似文献
4.
Rik Noorlandt Pauline P. Kruiver Marco P. E. de Kleine Marios Karaoulis Ger de Lange Antonio Di Matteo Julius von Ketelhodt Elmer Ruigrok Benjamin Edwards Adrian Rodriguez-Marek Julian J. Bommer Jan van Elk Dirk Doornhof 《Journal of Seismology》2018,22(3):605-623
The seismic hazard and risk analysis for the onshore Groningen gas field requires information about local soil properties, in particular shear-wave velocity (VS). A fieldwork campaign was conducted at 18 surface accelerograph stations of the monitoring network. The subsurface in the region consists of unconsolidated sediments and is heterogeneous in composition and properties. A range of different methods was applied to acquire in situ VS values to a target depth of at least 30 m. The techniques include seismic cone penetration tests (SCPT) with varying source offsets, multichannel analysis of surface waves (MASW) on Rayleigh waves with different processing approaches, microtremor array, cross-hole tomography and suspension P-S logging. The offset SCPT, cross-hole tomography and common midpoint cross-correlation (CMPcc) processing of MASW data all revealed lateral variations on length scales of several to tens of metres in this geological setting. SCPTs resulted in very detailed VS profiles with depth, but represent point measurements in a heterogeneous environment. The MASW results represent VS information on a larger spatial scale and smooth some of the heterogeneity encountered at the sites. The combination of MASW and SCPT proved to be a powerful and cost-effective approach in determining representative VS profiles at the accelerograph station sites. The measured VS profiles correspond well with the modelled profiles and they significantly enhance the ground motion model derivation. The similarity between the theoretical transfer function from the VS profile and the observed amplification from vertical array stations is also excellent. 相似文献
5.
Dispersion analysis is an important part of in-seam seismic data processing, and the calculation accuracy of the dispersion curve directly influences pickup errors of channel wave travel time. To extract an accurate channel wave dispersion curve from in-seam seismic two-component signals, we proposed a time–frequency analysis method based on single-trace signal processing; in addition, we formulated a dispersion calculation equation, based on S-transform, with a freely adjusted filter window width. To unify the azimuth of seismic wave propagation received by a two-component geophone, the original in-seam seismic data undergoes coordinate rotation. The rotation angle can be calculated based on P-wave characteristics, with high energy in the wave propagation direction and weak energy in the vertical direction. With this angle acquisition, a two-component signal can be converted to horizontal and vertical directions. Because Love channel waves have a particle vibration track perpendicular to the wave propagation direction, the signal in the horizontal and vertical directions is mainly Love channel waves. More accurate dispersion characters of Love channel waves can be extracted after the coordinate rotation of two-component signals. 相似文献
6.
Tamaz L. Chelidze Ia Shengelia Natalya Zhukova Teimuraz Matcharashvili George Melikadze Genady Kobzev 《Acta Geophysica》2016,64(3):567-588
Presently, there are a lot of observations on the significant impact of strong remote earthquakes on underground water and local seismicity. Teleseismic wave trains of strong earthquakes give rise to several hydraulic effects in boreholes, namely permanent water level changes and water level oscillations, which closely mimic the seismograms (hydro-seismograms). Clear identical anomalies in the deep borehole water levels have been observed on a large part of the territory of Georgia during passing of the S and Love–Rayleigh teleseismic waves (including also multiple surface Rayleigh waves) of the 2011 Tohoku M9 earthquake. The analysis carried out in order to find dynamically triggered events (non-volcanic tremors) of the Tohoku earthquake by the accepted methodology has not revealed a clear tremor signature in the test area: the Caucasus and North Turkey. The possible mechanisms of some seismic signals of unknown origin observed during passage of teleseismic waves of Tohoku earthquake are discussed. 相似文献
7.
V. N. Nikolaevskiy 《Izvestiya Physics of the Solid Earth》2016,52(1):1-13
Attenuation of seismic compression waves leads to the real existence of a fast P1 wave in rocks which are fully saturated with dropping fluid and a slow P2 wave in the rocks containing gas in their pores. This accounts for the seismic blanking zones below the gas horizons for the P1 waves. Oscillations of gaseous inclusions ensure the energy transfer to the dominant frequencies which are different for the cases of passive seismic (few Hz) and active source seismic (10–20 Hz). The intervals of dominant frequencies are determined from the negative attenuation of these low-frequency waves. According to the observations and the suggested equation, random noise amplifies the signal at these frequencies. Thus, the P2 waves at the dominant frequency of the active source seismics are applicable for elaborating on the details of the saturation of the production layer by hydrocarbons. The relation to the AVO method (Amplitude Variation with Offset) and dilatancy effect during the preparation of an earthquake is noted. 相似文献
8.
S. N. Bhattacharya 《Journal of Seismology》2017,21(1):237-241
Solutions of P-SV equations of motion in a homogeneous transversely isotropic elastic layer contain a factor exp(±ν j z), where z is the vertical coordinate and j?=?1, 2. For computing Rayleigh wave dispersion in a multi-layered half space, ν j is computed at each layer. For a given phase velocity (c), ν j becomes complex depending on the transversely isotropic parameters. When ν j is complex, classical Rayleigh waves do not exist and generalised Rayleigh waves propagate along a path inclined to the interface. We use transversely isotropic parameters as α H , β V , ξ, ? and η and find their limits beyond which ν j becomes complex. It is seen that ν j depends on ? and η, but does not depend on ξ. The complex ν j occurs when ? is small and η is large. For a given c/β V , the region of complex ν j in a ? -η plane increases with the increase of α H /β V . Further, for a given α H /β V , the complex region of ν j increases significantly with the decrease of c/β V . This study is useful to compute dispersion parameters of Rayleigh waves in a layered medium. 相似文献
9.
Nisar Ahmed Perveiz Khalid Hafiz Muhammad Bilal Shafi Patrick Connolly 《Acta Geophysica》2017,65(5):991-1007
The use of seismic direct hydrocarbon indicators is very common in exploration and reservoir development to minimise exploration risk and to optimise the location of production wells. DHIs can be enhanced using AVO methods to calculate seismic attributes that approximate relative elastic properties. In this study, we analyse the sensitivity to pore fluid changes of a range of elastic properties by combining rock physics studies and statistical techniques and determine which provide the best basis for DHIs. Gassmann fluid substitution is applied to the well log data and various elastic properties are evaluated by measuring the degree of separation that they achieve between gas sands and wet sands. The method has been applied successfully to well log data from proven reservoirs in three different siliciclastic environments of Cambrian, Jurassic, and Cretaceous ages. We have quantified the sensitivity of various elastic properties such as acoustic and extended elastic (EEI) impedances, elastic moduli (K sat and K sat–μ), lambda–mu–rho method (λρ and μρ), P-to-S-wave velocity ratio (V P/V S), and Poisson’s ratio (σ) at fully gas/water saturation scenarios. The results are strongly dependent on the local geological settings and our modeling demonstrates that for Cambrian and Cretaceous reservoirs, K sat–μ, EEI, V P/V S, and σ are more sensitive to pore fluids (gas/water). For the Jurassic reservoir, the sensitivity of all elastic and seismic properties to pore fluid reduces due to high overburden pressure and the resultant low porosity. Fluid indicators are evaluated using two metrics: a fluid indicator coefficient based on a Gaussian model and an overlap coefficient which makes no assumptions about a distribution model. This study will provide a potential way to identify gas sand zones in future exploration. 相似文献
10.
Upper mantle structure beneath central Western Europe from data on phase velocities of surface waves
Yu. G. Farafonova 《Izvestiya Physics of the Solid Earth》2008,44(1):60-68
The deep structure of the upper mantle is determined from data on phase velocities of Love and Rayleigh waves measured by a differential method on traces between two stations in central Western Europe. One-dimensional velocity structures are first constructed from data of each pair of stations, after which two-dimensional distributions of SH and SV velocities are calculated by the method of two-dimensional tomography from S wave velocities at fixed depths. The results are presented in the form of 2-D vertical structures of the average S wave velocity (S = (SV + SH)/2) constructed along profiles crossing the region in directions of the best resolution. The main structural features are a higher velocity zone at depths of 60–80 km in the area (48°–50°N, 9°–11°E) and a lower velocity zone in the western part of the region at depths of 100–150 km, probably extending farther beyond the studied area. 相似文献
11.
对煤巷小构造地震波场进行了数值模拟研究,分析了层状煤层中地震波的传播特征.研究表明:(1)在煤巷迎头前方煤层内以纵波震源激发的Rayleigh型槽波相对于体波能量较强,波列较长,波速较低.(2)沿煤层传播的Rayleigh型槽波在小构造面上产生Rayleigh型槽波反射波,反射Rayleigh型槽波垂直分量相对于水平分量能量较强.沿煤层反向传播的反射Rayleigh型槽波在煤巷迎头面上转换为沿煤巷底板传播的Rayleigh面波.沿煤巷底板可以接收到能量较强的反射Rayleigh型槽波产生的Rayleigh面波,其可以作为超前探测小构造面的特征波.在地震记录上反射Rayleigh型槽波产生的Rayleigh面波波至最迟,在时间域与其他波列时间间隔较大,其垂直分量能量相对于水平分量较强,在地震记录上容易识别.(3)在相同的地质条件下应用反射地震超前探测方法,标志煤巷迎头前方存在小构造面的反射地震波能量较弱,受煤巷顶、底板界面和采煤迎头面的强反射波干扰,在地震记录中难以识别. 相似文献
12.
To determine the shear wave velocity structure and predominant period features of T?naztepe in ?zmir, Turkey, where new building sites have been planned, active–passive surface wave methods and single-station microtremor measurements are used, as well as surface acquisition techniques, including the multichannel analysis of surface waves (MASW), refraction microtremor (ReMi), and the spatial autocorrelation method (SPAC), to pinpoint shallow and deep shear wave velocity. For engineering bedrock (V s > 760 m/s) conditions at a depth of 30 m, an average seismic shear wave velocity in the upper 30 m of soil (AVs30) is not only accepted as an important parameter for defining ground behavior during earthquakes, but a primary parameter in the geotechnical analysis for areas to be classified by V s30 according to the National Earthquake Hazards Reduction Program (NEHRP). It is also determined that Z1.0, which represents a depth to V s = 1000 m/s, is used for ground motion prediction and changed from 0 to 54 m. The sediment–engineering bedrock structure for T?naztepe that was obtained shows engineering bedrock no deeper than 30 m. When compared, the depth of engineering bedrock and dominant period map and geology are generally compatible. 相似文献
13.
In this study, two different historical structures built in Trabzon have been processed by ambient vibrations and seismic refraction measurements. One of the investigated historical structures is the Atatürk Pavilion built in the nineteenth century, and the other one is Hagia Sophia which was built in the thirteenth century. These two buildings are among the most important historical buildings in Trabzon and are very important for the tourism of the city. In order to determine peak/s frequency and amplitude from the horizontal-to-vertical spectral ratios (HVSRs), we have performed several measurements of ambient vibrations both inside (at different floors) and outside (on the ground) of structures. We have also conducted seismic prospecting to evaluate the vertical 1D and 2D profile of longitudinal and shear seismic waves, Vp and Vs, respectively. To this purpose, we have performed seismic refraction tomography and MASW. Ambient vibrations and seismic measurements were compared with each other. The results show that average predominant frequencies and HVSR amplitudes of inside and outside of Atatürk Pavilion are 4.0 Hz, 7.8 Hz and 2.6, 2.3, respectively. The Vp values vary from 300 to 2070 m/s, and the Vs for maximum effective depth is up to 790 m/s in Atatürk Pavilion. On the other hand, average predominant frequencies and HVSR amplitudes of inside and outside of Hagia Sophia and its tower are 4.7, 4.4 and 2.4 Hz and 1.6, 1.8 and 6.9, respectively. Vp values range from 450 to 2200 m/s, and Vs for maximum effective depth is also up to 1000 m/s in Hagia Sophia. The frequency values (F0?=?Vs/4 h) calculated from the velocities up to the maximum effective depth for Atatürk Pavilion are in good agreement with the predominant frequency values determined from ambient vibrations. Atatürk Pavilion and Hagia Sophia soils have been classed according to Eurocode 8 by using VS30 values. The class was defined as “B.” Moreover, the bedrock in studied area is basalt. The high Vp and Vs values are also compatible with the lithology. The HVSR curves measured at the Hagia Sophia show the presence of clear peaks when compared to the Atatürk Pavilion. At the same time, there are marked velocity changes in the Vs sections calculated in both areas. As a result, in both areas there are significant impedance contrasts in the subsoil. However, this impedance contrast is more evident in Hagia Sophia. This could be also compatible with a lithological transition. The possible soil–structure interaction was investigated by using all the results and evaluated in terms of resonance risk. It is thought that the probability of resonance risk at Atatürk Pavilion is low according to the ambient vibrations measurements. However, resonance risk should be taken into consideration at Hagia Sophia site since the predominant frequency values are very close to each other. Finally, this site should be investigated in detail and necessary precautions should be taken against the risk of resonance. 相似文献
14.
This paper investigated the effects of basin geometry and material property on the response of 2D trapezoidal sediment-filled basin to incident plane SH waves. Ten basin configurations with different geometries were developed, and then their seismic responses to both Ricker wavelets and seismic records were simulated by using an explicit finite difference scheme. The definition of deep/shallow basin, the precondition for the observation of prominent surface waves and the influential area of edge effects of the shallow basin were discussed quantitatively in this study. The followings were concluded: in the common velocity contrast range (v s1/v s2 < 10), the fundamental frequency a basin with W/H > 3.0 can be estimated approximately by 1D theory. The complexity of peak ground acceleration distribution pattern, the width of the most affected section as well as the amplitude of ground motion in the Edge Region increase with incident frequency. Prominent surface waves can only be observed when the incident wavelength is shorter than the critical wavelength λ c . The interaction between incident wave and basin dynamic property plays a dominant role on the peak ground acceleration amplitude while the interaction between incident wave and geometry plays a more significant role on the peak ground acceleration distribution. For very shallow basin, different areas along the basin width are affected to different extents. Only a limited area close to the basin edge is influenced significantly. It is more feasible to propose spectral aggravation factor for different surface zones respectively than a uniform constant as a tool to calibrate the 1D-based design spectrum so as to take the basin effects into account. 相似文献
15.
Stepwise joint inversion of surface wave dispersion,Rayleigh wave ZH ratio,and receiver function data for 1D crustal shear wave velocity structure 
下载免费PDF全文
下载免费PDF全文 Accurate determination of seismic velocity of the crust is important for understanding regional tectonics and crustal evolution of the Earth. We propose a stepwise joint linearized inversion method using surface wave dispersion, Rayleigh wave ZH ratio (i.e., ellipticity), and receiver function data to better resolve 1D crustal shear wave velocity (v S) structure. Surface wave dispersion and Rayleigh wave ZH ratio data are more sensitive to absolute variations of shear wave speed at depths, but their sensitivity kernels to shear wave speeds are different and complimentary. However, receiver function data are more sensitive to sharp velocity contrast (e.g., due to the existence of crustal interfaces) and v P/v S ratios. The stepwise inversion method takes advantages of the complementary sensitivities of each dataset to better constrain the v S model in the crust. We firstly invert surface wave dispersion and ZH ratio data to obtain a 1D smooth absolute v S model and then incorporate receiver function data in the joint inversion to obtain a finer v S model with better constraints on interface structures. Through synthetic tests, Monte Carlo error analyses, and application to real data, we demonstrate that the proposed joint inversion method can resolve robust crustal v S structures and with little initial model dependency. 相似文献
16.
Yu. V. Kharazova O. V. Pavlenko K. A. Dudinskii 《Izvestiya Physics of the Solid Earth》2016,52(3):399-412
The relationship between the characteristics of seismic waves in the Western Caucasus and the geological-tectonic structure of the region is studied for identifying the specificity of seismic propagation in the mountainous regions with a complicated geological structure and forecasting the characteristics of the propagation from the geological and tectonic data. The interpretation is presented for the estimates of the Q-factor of the medium (Q(f) ~ 55f0.9 in the region of Sochi and Q(f) ~ 90f0.7 in the region of Anapa), seismic wave enhancement in the upper crustal layers (A(f) ~ 1), and peak ground acceleration residuals, which were previously determined from the records of the local earthquakes and show the distributions of local variations in the parameters of seismic wave radiation and propagation. The obtained characteristics are interpreted in the context of the up-to-date information about the tectonic, geological, and deep structure of the epicentral zones in the Western Caucasus and neighboring territory of the Black Sea. The discrepancies revealed in the low-frequency behavior of the Q-factor in the vicinities of Sochi and Anapa is accounted for by the spatial scale and character of tectonic dislocations of the rocks in these regions. The local variations in the parameters of seismic radiation and propagation are probably related to the geological features of the region such as the fault structures, including the thrusts, shatter zones, oblique seismic boundaries, variations in the thickness and consolidation of the sedimentary cover, as well as the peculiarities in the structure and material composition of the basement. 相似文献
17.
In this study, we have modeled the density(ρ) and bulk sound velocity(VΦ) profiles of the bottom lower mantle using the experimental thermal equation of state(EoS) parameters of lower-mantle minerals, including bridgmanite, ferropericlase,CaSiO3-perovskite, and post-perovskite. We re-evaluated the literature pressure-volume-temperature relationships of these minerals using a self-consistent pressure scale in order to avoid the long-standing pressure scale problem and to provide more reliable constraints on the thermal EoS parameters. With the obtained thermal EoS parameters, we have constructed the ρ and VΦ profiles of the bottom lower mantle in different composition, mineralogy, and temperature models. Our modelling results show that the variations of chemistry, mineralogy, and temperature have different seismic signatures from each other. The Fe and Al enrichment at the bottom lower mantle can cause an increase in ρ but greatly lower VΦ. A change in mineralogy needs to be considered with the lateral variation in temperature. The cold slabs will be shown as denser regions compared to the normal mantle because of the combined effect of a lower temperature and the presence of a denser post-perovskite at a shallower depth,whereas the hot regions will have a 1–2% lower ρ than the normal mantle. VΦ of both cold slabs and hot regions will be lower than the normal mantle when bridgmanite is the dominant phase in the normal mantle, yet they will be greater once bridgmanite transforms into post-perovskite in the normal mantle. Our modeling also shows that the presence of a(Fe, Al)-enriched bridgmanite thermal pile above the core-mantle boundary will exhibit a seismic signature of enhanced ρ and VΦ, but a reduced VS,which is consistent with the observed seismic anomalies in the large-low-shear-velocity-provinces(LLSVPs). The existence of such a(Fe, Al)-enriched bridgmanite thermal pile thus can help to understand the origin of the LLSVPs. These results provide new insights for the chemical and structure of the deepest lower mantle. 相似文献
18.
Results of investigation of the lithosphere in the Kamchatka seismic focal zone from dynamic characteristics of earthquake records obtained at regional stations are presented. It is assumed that the specificity of the source zone can be estimated by the relation Cr = K P ? bK S ? c characterizing relative energies (energy classes, according to [Fedotov, 1972]) of short period transverse and longitudinal waves in the source. Azimuthal, spatial, and temporal variations in Cr and their relation to focal mechanisms are examined. Spatiotemporal variations in this parameter are shown to be caused by the influence of variations in the conditions in the source zone (its substance or process) on the radiation of P and S waves. 相似文献
19.
The evaluation and design of stone column improvement ground for liquefaction mitigation is a challenging issue for the state of practice. In this paper, a shear wave velocity-based approach is proposed based on the well-defined correlations of liquefaction resistance (CRR)-shear wave velocity (V s)-void ratio (e) of sandy soils, and the values of parameters in this approach are recommended for preliminary design purpose when site specific values are not available. The detailed procedures of pre- and post-improvement liquefaction evaluations and stone column design are given. According to this approach, the required level of ground improvement will be met once the target V s of soil is raised high enough (i.e., no less than the critical velocity) to resist the given earthquake loading according to the CRR-V s relationship, and then this requirement is transferred to the control of target void ratio (i.e., the critical e) according to the V s-e relationship. As this approach relies on the densification of the surrounding soil instead of the whole improved ground and is conservative by nature, specific considerations of the densification mechanism and effect are given, and the effects of drainage and reinforcement of stone columns are also discussed. A case study of a thermal power plant in Indonesia is introduced, where the effectiveness of stone column improved ground was evaluated by the proposed V s-based method and compared with the SPT-based evaluation. This improved ground performed well and experienced no liquefaction during subsequent strong earthquakes. 相似文献
20.
S. D. Kromskii O. V. Pavlenko I. P Gabsatarova 《Izvestiya Physics of the Solid Earth》2018,54(2):222-232
Based on the Anapa (ANN) seismic station records of ~40 earthquakes (MW > 3.9) that occurred within ~300 km of the station since 2002 up to the present time, the source parameters and quality factor of the Earth’s crust (Q(f)) and upper mantle are estimated for the S-waves in the 1–8 Hz frequency band. The regional coda analysis techniques which allow separating the effects associated with seismic source (source effects) and with the propagation path of seismic waves (path effects) are employed. The Q-factor estimates are obtained in the form Q(f) = 90 × f 0.7 for the epicentral distances r < 120 km and in the form Q(f) = 90 × f1.0 for r > 120 km. The established Q(f) and source parameters are close to the estimates for Central Japan, which is probably due to the similar tectonic structure of the regions. The shapes of the source parameters are found to be independent of the magnitude of the earthquakes in the magnitude range 3.9–5.6; however, the radiation of the high-frequency components (f > 4–5 Hz) is enhanced with the depth of the source (down to h ~ 60 km). The estimates Q(f) of the quality factor determined from the records by the Sochi, Anapa, and Kislovodsk seismic stations allowed a more accurate determination of the seismic moments and magnitudes of the Caucasian earthquakes. The studies will be continued for obtaining the Q(f) estimates, geometrical spreading functions, and frequency-dependent amplification of seismic waves in the Earth’s crust in the other regions of the Northern Caucasus. 相似文献