首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Thermally altered pods of coal of very high rank have been observed in a high-volatile-bituminous coal seam in the eastern side of Eagle Mountain, Elk Valley Coalfield, British Columbia. Rank changes have been measured over a strike distance of 7.5 m from 1.24% to 7.1% Ro max, corresponding to a rank gradient of 0.78% Rom−1.Petrologically, unaltered to extremely altered vitrinite showing nongranular (basic) anisotropy, mosaic-textured liptinite and pyrolytic carbon are the most abundant components. The limited presence of mosaic on vitrinite is an indication that the coal seam may have been weathered prior to being heat-affected.Evidence points to localized temperatures as high as 1,000°C, which could have been caused by a lightning strike. The eastern side of Eagle Mountain has experienced higher temperatures than the western side, and it appears that the heat ‘front’ and zone of alteration have an irregular pattern, pointing to saturation of parts of the coal seam by water.Four types of pyrolytic carbon having distinct morphology, anisotrophy and optical path with increasing temperature were observed. Reflectance of pyrolytic carbon falls within the zone of heat-affected coals, whereas the optical path of heat-affected Seam 15 samples is different from that of fresh coal with increasing rank.Finally, the reflectance of vitrinite in heat-affected coal is higher than the reflectance of vitrinite in carbonaceous shale in the Seam 15 section.  相似文献   

2.
This study describes changes of surface roughness of semifusinite and fusinite as an indicator of structural alteration resulting from heat treatment at 400–1200 °C. Surface roughness has been investigated by atomic force microscopy of inertinite concentrates from coking coals (vitrinite reflectance Rr = 1.07%–1.41%) from the Upper Silesian Coal Basin of Poland (Namurian C — Westphalian A). Unheated fusinite has a higher surface roughness than semifusinite from the same coal. The average surface roughness of semifusinite decreases with the Swelling Index of the parent coal. Heating increases the surface roughness of semifusinite and fusinite. Increase in the average surface roughness is stronger for semifusinite than fusinite and correlates to increasing reflectance of these macerals. The surface roughness of semifusinite correlates to the relative mass loss of the inertinite concentrates during heating. After heating to 1200 °C fusinite has a lower average surface roughness than semifusinite from the same coal. Consequently, average surface roughness can be used as a measure of structural alteration of inertinite group macerals during heat treatment.  相似文献   

3.
The chemical composition of the organic matter in the principal macerals of high-volatile bituminous coals from the Gunnedah Basin, New South Wales (Rvmax of telocollinite between 0.6 and 1.1%) has been evaluated from polished section specimens using an electron microprobe technique. Highest proportions of carbon occur in the inertinite macerals, especially fusinite and secretinite (formerly resino-sclerotinite), as well as in sporinite; lowest proportions of carbon occur in the different macerals of the vitrinite group. Oxygen shows the reverse trend, being most abundant in vitrinite and least abundant in the inertinite components, whereas sulphur is lowest in the inertinites and highest in the liptinite (mainly sporinite) present. Evaluations of maceral composition, using the carbon content of telocollinite as a rank indicator, show that carbon is more abundant in both sporinite and semifusinite, relative to vitrinite, in low-rank high-volatile bituminous coals. The difference decreases with increasing rank, and the proportion of carbon in telocollinite becomes essentially the same as that in sporinite and semifusinite at carbon contents of about 89 and 91%, respectively. The carbon content of fusinite and secretinite, on the other hand, does not seem to vary appreciably with rank advance. No significant difference in composition occurs in the rank range studied between the three vitrinite varieties present, desmocollinite, telocollinite and a more highly reflecting telocollinite resembling pseudovitrinite. No evidence was found to indicate a higher hydrogen content, relative to telocollinite, for the vitrinite matrix of desmocollinite.  相似文献   

4.
The Early Cretaceous coal deposits of the Khasyn coalfield are intruded by Palaeogene diabase dikes. The coal has vitrinite reflectance values of 2.0–2.5% Ro, and characteristics of normal anthracite at some distance from the dikes, but at direct contact with the dike two morphological coal varieties occur: coal inclusions in the diabase dike and dispersed carbonaceous matter within the dike rock. Both types of coaly matter have properties typical of anthracites: strong anisotropy, altered internal structure and high vitrinite reflectance values ranging from 3.8 to 5.5% Ro. The X-ray diffraction measurements of the interplanar spacing d(002) and the crystallite sizes Lc and La show rather similar values for coal inclusions in the dike and dispersed carbonaceous matter. The additional reflection at 3.37 Å, corresponding to semi-graphite admixture, occurs in the coal and carbonaceous matter inside the dike and is absent in the natural coal outside the dike.  相似文献   

5.
A worldwide data set of more than 500 humic coals from the major coal-forming geological periods has been used to analyse the evolution in the remaining (Hydrogen Index, HI) and total (Quality Index, QI) generation potentials with increasing thermal maturity and the ‘effective oil window’ (‘oil expulsion window’). All samples describe HI and QI bands that are broad at low maturities and that gradually narrow with increasing maturity. The oil generation potential is completely exhausted at a vitrinite reflectance of 2.0–2.2%Ro or Tmax of 500–510 °C. The initial large variation in the generation potential is related to the original depositional conditions, particularly the degree of marine influence and the formation of hydrogen-enriched vitrinite, as suggested by increased sulphur and hydrogen contents. During initial thermal maturation the HI increases to a maximum value, HImax. Similarly, QI increases to a maximum value, QImax. This increase in HI and QI is related to the formation of an additional generation potential in the coal structure. The decline in QI with further maturation is indicating onset of initial oil expulsion, which precedes efficient expulsion. Liquid petroleum generation from humic coals is thus a complex, three-phase process: (i) onset of petroleum generation, (ii) petroleum build-up in the coal, and (iii) initial oil expulsion followed by efficient oil expulsion (corresponding to the effective oil window). Efficient oil expulsion is indicated by a decline in the Bitumen Index (BI) when plotted against vitrinite reflectance or Tmax. This means that in humic coals the vitrinite reflectance or Tmax values at which onset of petroleum generation occurs cannot be used to establish the start of the effective oil window. The start of the effective oil window occurs within the vitrinite reflectance range 0.85–1.05%Ro or Tmax range 440–455 °C and the oil window extends to 1.5–2.0%Ro or 470–510 °C. For general use, an effective oil window is proposed to occur from 0.85 to 1.7%Ro or from 440 to 490 °C. Specific ranges for HImax and the effective oil window can be defined for Cenozoic, Jurassic, Permian, and Carboniferous coals. Cenozoic coals reach the highest HImax values (220–370 mg HC/g TOC), and for the most oil-prone Cenozoic coals the effective oil window may possibly range from 0.65 to 2.0%Ro or 430 to 510 °C. In contrast, the most oil-prone Jurassic, Permian and Carboniferous coals reach the expulsion threshold at a vitrinite reflectance of 0.85–0.9%Ro or Tmax of 440–445 °C.  相似文献   

6.
The orientation of the optical indicating surface of vitrinite in reflected light has been determined following deformation at 350 and 500°C, confining pressures of 500 and 800 MPa and a strain rate of 10−5 s−1. High temperature and large strain have facilitated reorientation of the indicating surface, increase in anisotropy (bireflectance) and an increase in maximum vitrinite reflectance. In a specimen deformed at 500°C and 23% axial strain the maximum vitrinite reflectance has been reoriented more than 70° from close to parallel to σ1 in the undeformed state to perpendicular to σ1 following deformation. Orientation of the optical indicating surface of some of the deformed specimens suggests the orientation of the maximum reflectance is a composite product of the original orientation of the indicating surface and an orientation produced during deformation.  相似文献   

7.
Micro-FTIR spectroscopy of liptinite macerals in coal   总被引：3，自引：0，他引：3  
Reflectance FTIR microspectroscopy has been used to investigate the chemical structure of the liptinite macerals, alginite, bituminite, sporinite, cutinite and resinite in bituminous coals of Carboniferous to Tertiary age. In comparison with the spectra of vitrinite in the same coals, the micro-FTIR spectra of liptinite macerals are characterized by stronger aliphatic CHx absorptions at 3000–2800 and 1460–1450 cm−1, less intense aromatic C=C ring stretching vibration and aromatic CH out of plane deformation at 1610–1560 and 900–700 cm−1 respectively and various intense acid C=O group absorptions at 1740–1700 cm−1. The peaks at 1000–900 cm−1 due to aliphatic CH2 wagging vibrations in olefins and at 730–720 cm−1 due to CH2 rocking vibration in long chain aliphatic substances ([CH2]n, n≥4), are characteristic of liptinite macerals. Collectively the micro-FTIR spectral characteristics indicate that liptinite is composed of greater numbers of long chain aliphatics, fewer aromatics and a broader range of oxygen-containing groups than other macerals. Marked differences exist in micro-FTIR spectra within the liptinite maceral group. Alginite has the strongest aliphatic and least aromatic absorptions followed by bituminite, resinite, cutinite and sporinite. The aliphatic components in alginite are the longest chained and least branched whereas those in sporinite are the shortest chained and most branched. Bituminite, resinite and cutinite are intermediate. Notable differences in micro-FTIR spectra of individual liptinite macerals, such as intensities and peak locations of aromatic C=C in alginite, C=O groups in bituminite and resinite and substituted aromatic CH and C–O–C groups in cutinite and sporinite, also exist, which are attributed to differences in depositional environments or biotaxonomy.  相似文献   

8.
Thermal maturity was determined for about 120 core, cuttings, and outcrop samples to investigate the potential for coalbed gas resources in Pennsylvanian strata of north-central Texas. Shallow (< 600 m; 2000 ft) coal and carbonaceous shale cuttings samples from the Middle-Upper Pennsylvanian Strawn, Canyon, and Cisco Groups in Archer and Young Counties on the Eastern Shelf of the Midland basin (northwest and downdip from the outcrop) yielded mean random vitrinite reflectance (Ro) values between about 0.4 and 0.8%. This range of Ro values indicates rank from subbituminous C to high volatile A bituminous in the shallow subsurface, which may be sufficient for early thermogenic gas generation. Near-surface (< 100 m; 300 ft) core and outcrop samples of coal from areas of historical underground coal mining in the region yielded similar Ro values of 0.5 to 0.8%. Carbonaceous shale core samples of Lower Pennsylvanian strata (lower Atoka Group) from two deeper wells (samples from ~ 1650 m; 5400 ft) in Jack and western Wise Counties in the western part of the Fort Worth basin yielded higher Ro values of about 1.0%. Pyrolysis and petrographic data for the lower Atoka samples indicate mixed Type II/Type III organic matter, suggesting generated hydrocarbons may be both gas- and oil-prone. In all other samples, organic material is dominated by Type III organic matter (vitrinite), indicating that generated hydrocarbons should be gas-prone. Individual coal beds are thin at outcrop (< 1 m; 3.3 ft), laterally discontinuous, and moderately high in ash yield and sulfur content. A possible analog for coalbed gas potential in the Pennsylvanian section of north-central Texas occurs on the northeast Oklahoma shelf and in the Cherokee basin of southeastern Kansas, where contemporaneous gas-producing coal beds are similar in thickness, quality, and rank.  相似文献   

9.
Immature vitrinite samples from a Miocene lignite seam of western Germany (H/C = 1.14, O/C = 0.41) and alginite concentrates from a Tasmanite deposit of Australia (H/C = 1.60, O/C = 0.10) were pyrolyzed in a stream of argon at heating rates of 0.1 and 2.0°C/min up to temperatures varying from 200 to 670°C. The solid maceral residues were subjected to elemental and microscopical analysis and studied by IR and 13C CP/MAS NMR spectroscopy with respect to structural modifications.The maximum pyrolytic weight loss amounts to 60% of the initial organic matter in the case of vitrinite and to 85% for alginite, the onset of degradation reactions being shifted to higher temperatures with increasing rate of heating. Both infrared and NMR spectra of the vitrinite samples indicate a rapid decomposition of the cellulose component upon heating whereas lignin related structures such as aromatic ether linkages remain remarkably stable. The main hydrocarbon release from vitrinite occurs at very early evolution stages (Tmax = 296°C, Rm = 0.20% at 0.1°C/min; Tmax = 337°C, Rm = 0.23 at 2.0°C/min). Hydrocarbon generation from alginite requires higher temperatures (Tmax = 388 and 438°C) and is completed within a distinctly narrower temperature range.The pronounced increase of vitrinite reflectance between 350 and 670°C seems to be associated with a rather time-consuming reorganization of the residual organic material. The concomitant growth of polyaromatic units is illustrated by the increasing intensity ratio of the aromatic ring stretching vibration bands at 1600 and 1500 cm−1. These reactions are moreover marked by increasing loss of phenolic oxygen and by increasing conversion of aliphatic carbon into fixed aromatic carbon.  相似文献   

10.
The results of the study of optical properties of 13 anthracites from different parts of the world are presented in this paper. Measurements of reflectance values were made on non-oriented vitrinite grains for a minimum of 300 points per sample. The reconstruction of Reflectance Indicating Surfaces (RIS) were made by Kilby's method [Kilby, W.E., 1988. Recognition of vitrinite with non-uniaxial negative reflectance characteristics. Int. J. Coal Geol. 9, 267–285; Kilby, W.E., 1991. Vitrinite reflectance measurement — some technique enhancements and relationships. Int. J. Coal Geol. 19, 201–218]. It was found that the use of Kilby's method for strongly anisotropic materials like anthracites did not give unambiguous results. Some improvement in Kilby's method, consisting of the division of the cumulative cross-plot into several elemental components, is suggested. Each elemental cross-plot corresponds to a textural class of anthracite, which is characterized by the values of RIS main axes RMAX(k), RINT(k) and RMIN(k) (k=1,2,…n; n — number of classes). The global texture of anthracite is characterized as a RIS with main axes calculated as the weighted means of , and for each class of this anthracite.The division of cumulative Kilby's cross-plot on elemental components makes possible the calculation of new coefficients Ht and H10 characterizing the heterogeneity of the structure and texture of anthracites. The results of our study show that all anthracites have biaxial negative textures, but their heterogeneity varies in a wide range of Ht and H10 coefficients depending upon the individual coal basin.  相似文献   

11.
The quantitative maceral study of the Queen seam from Mailaram coalfield of Godavari valley has displayed alternate coal bands rich in vitrinite/liptinite or inertinite. The random vitrinite reflectance (Ro max. %) of these coals, from top part ranges from 0.50 to 0.64%. However, the bottom part of the seam has indicated lower reflectance, between 0.49 and 0.52%. Thus, the Queen seam, in general, has attained high volatile bituminous C rank. The study indicates that the depositional site has been a slowly sinking basin that witnessed alternate dry (oxidizing) and wet (reducing) spells. This subsequently caused fluctuation in water table of the basin and the formation of oxic and anaoxic moor condition, where accumulated vegetal resource transformed into mixed and fusic coal types in due course of time. Being high in liptinite and vitrinite contents and low mineral matter, the Queen seam of Mailaram coalfield has high economic potential.  相似文献   

12.
Upper Triassic to Middle Jurassic coals from the Alborz region of northern Iran were analyzed by reflected light-fluorescence microscopy and Rock Eval 6® pyrolysis to evaluate their regional rank variation, degree of hydrothermal alteration, and petroleum generative potential. The coal ranks in the region range from a low of 0.69%RoR in the Glanddeh-Rud area to a high of 1.02%RoR in the Gajereh area. Tmax (°C) values (Rock Eval 6 pyrolysis) also increase progressively with increasing vitrinite %Ro values, however Tmax is suppressed lower than would be expected for each rank ranging from 428 °C for the Glandeeh coal to 438 °C for the Gajereh coal. Tmax suppression may be caused by maceral composition and soluble organics within the coal. Moderately high hydrogen indices, persistent and oily exudations from the coals during UV exposure, and traces of hydrocarbon fluid inclusions suggest that liquid petroleum was likely generated within some of the coals.  相似文献   

13.
The applicability of the reflectance micro-Fourier Transform infra-red spectroscopy (FTIR) technique for analyzing the distribution of functional groups in coal macerals is discussed. High quality of spectra, comparable to those obtained using other FTIR techniques (KBr pellet and transmission micro-FTIR), indicate this technique can be applied to characterizing functional groups under most conditions. The ease of sample preparation, the potential to analyze large intact samples, and ability to characterize organic matter in areas as small as 20 μm are the main advantages of reflectance micro-FTIR. The quantitative aspects of reflectance micro-FTIR require further study.The exaples from the coal seams of the Mist Mountain Formation, British Columbia show that at high volatile bituminous rank, reflectance micro-FTIR provides valuable information on the character of aliphatic chains of vitrinite and liptinite macerals. Because the character of aliphatic chains influences bond disassociation energies, such information is useful from a hydrocarbon generation viewpoint. In medium volatile bituminous coal liptinite macerals are usually not detectable but this technique can be used to study the degree of oxidation and reactivity of vitrinite and semifusinite.  相似文献   

14.
The maceral and microlithotype composition of selected coals has been investigated with respect to the grinding properties, specifically Hardgrove grindability index (HGI), of the coals. The study expands upon previous investigations of HGI and coal petrology by adding the dimension of the amount and composition of the microlithotypes. Coal samples, both lithotypes and whole channels, were selected from restricted rank ranges based on vitrinite maximum reflectance: 0.75–0.80% Rmax, 0.85–0.90% Rmax and 0.95–1.00% Rmax. In this manner, the influence of petrographic composition can be isolated from the influence of rank. Previous investigations of high volatile bituminous coals demonstrated that, while rank is an important factor in coal grindability, the amount of liptinite and liptinite-rich microlithotypes is a more influential factor. In this study, we provide further quantitative evidence for the influence of microlithotypes on HGI and, ultimately, on pulverizer performance.  相似文献   

15.
A petrological, organic geochemical and geochemical study was performed on coal samples from the Soko Mine, Soko Banja basin, Serbia. Ten coal and two carbonaceous clay samples were collected from fresh, working faces in the underground brown coal mine from different parts of the main coal seam. The Lower Miocene, low-rank coal of the Soko Mine is a typical humic coal with huminite concentrations of up to 76.2 vol.%, liptinite less than 14 vol.% and inertinite less than 11 vol.%. Ulminite is the most abundant maceral with variable amounts of densinite and clay minerals. Sporinite and resinite are the most common macerals of the liptinite group. Inertodetrinite is the most abundant maceral of the inertinite group. The mineral-bituminous groundmass identified in some coal samples, and carbonaceous marly clay, indicate sub-aquatic origin and strong bacterial decomposition. The mean random huminite reflectance (ulminite B) for the main coal seam is 0.40 ± 0.05% Rr, which is typical for an immature to early mature stage of organic matter.The extract yields from the coal of the Soko Banja basin ranges from 9413 to 14,096 ppm, in which alkanes constituted 1.0–20.1%, aromatics 1.3–14.7%, asphaltenes 28.1–76.2% and resins 20.2–43.5%. The saturated hydrocarbon fractions included n-C15 to n-C32, with an odd carbon number that predominate in almost all the samples. The contents of n-C27 and n-C29 alkanes are extremely high in some samples, as a contribution of epicuticular waxes from higher plants. Acyclic isoprenoid hydrocarbons are minor constituents in the aliphatic fraction, and the pristane/phytane (Pr/Ph) ratio varies between 0.56 and 3.13, which implies anaerobic to oxic conditions during sedimentation. The most abundant diterpanes were abietane, dehydroabietane and 16α(H)-phyllocladane. In samples from the upper part of the coal seam, diterpanes are the dominant constituents of the alkane fraction. Polycyclic alkanes of the triterpane type are important constituents of alkane fractions. The occurrence of ββ- and αβ-type hopanes from C27 to C31, but without C28, is typical for the Soko Banja coals.The major and trace elements in the coal were analysed using X-ray fluorescence (XRF), and inductively coupled plasma-mass spectrometry (ICP-MS). In comparison with world lignites, using the geometric mean value, the coal from the Soko Banja Basin has a high content of strontium (306.953 mg/kg). Higher values than the world lignites were obtained for Mo (3.614 mg/kg), Ni (8.119 mg/kg), Se (0.884 mg/kg), U (2.642 mg/kg) and W (0.148 mg/kg). Correlation analysis shows inorganic affinity for almost all the major and trace elements, except for S, which has an organic affinity.  相似文献   

16.
Macerals like sporinite, cutinite, suberinite and resinite of the liptinite group have been insufficiently recorded in Indian Permian Gondwana coals, until the fluorescence microscopy came into existence. With the introduction of this technique, macerals like bituminite, fluorinite and exsudatinite were convincingly recognized and alginite and liptodetrinite, normally mistaken for mineral matter under normal reflected light in routine coal petrographic analysis, were identified with certainty. Thus, fluorescence microscopy has added certain new macerals to the tally of the liptinite group and has increased their overall proportion in Indian Gondwana coals.In addition to the liptinite group, collodetrinite (=desmocollinite) and a certain fraction of collotelinite (=telocollinite) macerals of the vitrinite group were found to be fluorescing with dull reddish-brown to dark brown colours. Certain semifusinite and inertodetrinite macerals of inertinite group were also found to fluoresce with almost identical intensity and colour as that of the associated perhydrous (fluorescing) vitrinite. Contributions of degraded resinite, algal matter and bitumen in the formation of perhydrous vitrinite have been established. The fluorescence behaviour of inertinite appears to be related with its genesis from partial oxidation of resin/bitumen-impregnated cell walls.  相似文献   

17.
This work presents the results from evaluating the gases sorbed by coal samples extracted from the Paleocene Guasare Coalfield (Marcelina Formation, northwestern Venezuela), as well as by their distinct maceral concentrates. The aim of this work has been to obtain an initial experimental main value of the gas content per unit weight of high volatile bituminous A coal samples from the open-pit Paso Diablo mine. An additional goal was to study differences in the CH4 storage ability of the distinct maceral groups forming part of the coal matrix. Both the coal samples and the maceral concentrates were studied by thermogravimetric analysis (TGA) in order to determine the temperature to be used in subsequent experiments. On-line analyses of hydrocarbons (C1, C2, C3) and CO2 yielded gas concentrations, plus δ13C values. Thermogenic gas is prevalent in the Guasare coals with vitrinite reflectance (%Ro) values from 0.65% to 0.88%. The amount of gas retained in the coals and maceral concentrates was measured with a special device that allows determination of the volume of gas sorbed by a solid sample subjected to controlled thermal treatment. The average coalbed gas concentration obtained was 0.51 cm3/g. The following list of maceral concentrates shows the relative capacity for the volume of sorbed gas per unit weight: inertinite > low-density vitrinite > liptinite ≈ high-density vitrinite. It is concluded that the gas volumes retained in the distinct maceral concentrates are not controlled by porosity but rather by their microscopic morphology.  相似文献   

18.
There are at least two sapropelic units associated with Late Palaeozoic black shales in Central Europe. The older unit, of Late Carboniferous age, is the lower part of the Anthracosia Shales in the Intrasudetic Basin, and the younger one is the well-known Zechstein Kupferschiefer in both the Foresudetic Monocline and the Northsudetic Basin. The first unit is of lacustrine origin, while the second one represents deposition in a shallow marine depositional environment. Both units contain high amounts of organic matter, thus being typical black shales.The organic matter dispersed in these shales was studied petrographically. In general, the vitrinite reflectance of the shales studied indicates variable, but moderate organic matter maturity (0.68–1.25%), equivalent to the oil window. Detailed microscopic studies of the organic material dispersed in the lower unit of the Anthracosia Shales showed that liptinite, especially alginite is the most abundant component. Secondary altered organic matter, i.e. solid hydrocarbons, rarely occurs. Organic components together with mineral matter constitute a lacustrine sapropelic association, a humic (terrestrial) association and an intermediary association. The character and predominance of alginite and lacustrine sapropelic association are indicative of an open-lacustrine depositional environment. In general, this organic composition is typical of type I kerogen.Microscopic analysis of the Kupferschiefer revealed a mixture of liptinite, vitrinite and inertinite macerals, and other organic components such as amorphous sapropelic mass (ASM) and solid bitumens. The most common organic components are liptinite macerals. Bituminite and alginite predominate, and are diagnostic macerals of this unit. The amount of bituminite locally exceeds 85 vol.%. Other liptinite macerals such as sporinite and liptodetrinite, are present in significantly lower amounts, one exception being ASM, which may be present in higher amounts. Humic constituents (vitrinite and inertinite) are rare, present in small amounts in the Kupferschiefer beds. The organic matter composition points to type II kerogen for this unit.  相似文献   

19.
Petrographic analyses were carried out on thin coals and coaly sediments from the Lower Carboniferous Mattson Formation at Clausen Creek and Jackfish Gap-Yohin Ridge in the northern part of the Liard Basin, northern Canada. The composition and optical characteristics indicate that the coals are high-volatile bituminous B, predominantly sapropelic (canneloid) and accumulated subaquatically.The coals are dominantly composed of inertinite-rich and exinite-rich durities with subsidiary inertites and clarodurites; vitrite is minor and liptite is rare. The inertinite-rich microlithotypes are dominated by semifusinite, but micrinite, semimacrinite and ?resino-inertinites are abundant. Sporinite, comprising megaspores, crassispores, tenuispores and miospores, is the dominant liptinite maceral with subsidiary cutinite and minor alginite. Except for pyrite, mineral matter is minimal.Three populations of telocollinite are observed: a low-reflectance variety (I), commonly associated with micrinite (as vitrinertite), displays weak brown fluorescence and a reflectance some 0.4-0.5% lower than type II; type II is non-fluorescing telocollinite, with intermediate reflectance (0.67-0.74% Rom), it occurs as vitrite and is also associated with micrinite; and a higher-reflectance telocollinite (III), having no fluorescence or association with micrinite, has variable reflectance (0.74-0.8% Rom) implying higher oxidation or gelification levels.The abundance of semimacrinite, macrinite and ?resino-inertinites in inertites and durites (I) suggests that much of the peat accumulated subaquatically. Furthermore, fluorescing vitrinite and an abundance of micrinite (derived by oxidation or coalification of bituminite), suggest that the coal accumulated under anaerobic conditions. The predominance of semifusinite in humic laminae and micrinite in sapropelic layers suggests extensive surface or near-surface oxidation of the peat. Oxidised sporinites suggest that they were wind-borne.Depositional environment is interpreted as marginal marine, perhaps in shallow lakes in the middle to upper delta plain. Peat accumulations probably began subaquatically at the oxygen-hydrogen sulphide interface, but periodic subaerial exposure and natural oxidation gave rise to the high inertinite coals. Upper Mattson coals are interbedded with algal laminites and probably accumulated in a lagoonal setting.  相似文献   

20.
The coal seams of Sawang Colliery, East Bokaro Coalfields are bituminous to sub-bituminous in nature and categorized as high gaseous seams (degree II to degree III level). These seams have the potential for coal bed methane (CBM) and their maturity increases with increasing depth, as a result of enhanced pressure-temperature conditions in the underground. The vitrinite maceral group composition of the investigated coal seams ranges from 62.50–83.15%, whereas the inertinite content varies from 14.93–36.81%. The liptinite content varies from 0.66% to 3.09%. The maximum micro-pores are confined within the vitrinite group of macerals. The coal seams exhibit vitrinite reflectance values (Ro% calculated) from 0.94% (sample CG-97) to 1.21% (sample CG-119). Proximate analyses of the investigated coal samples reveal that the moisture content (M%) ranges from 1.28% to 2.98%, whereas, volatile matter (VM%) content is placed in the range of 27.01% to 33.86%. The ash content (A%) ranges from 10.92% to 30.01%. Fixed carbon (FC%) content varies from 41.53% to 55.93%. Fuel ratio variation shows a restricted range from 1.53 to 1.97. All the coal samples were found to be strongly caking and forming coke buttons. The present study is based on the adsorption isotherm experiments carried out under controlled P-T conditions for determination of actual gas adsorption capacity of the coal seams. This analysis shows that the maximum methane gas adsorbed in the coal sample CG-81 is 17 m3/t (Std. daf), at maximum pressure of 5.92 MPa and experimental temperature of 30°C. The calculated Langmuir regression parameters PL and VL range from 2.49 to 3.75 MPa and 22.94 to 26.88 m3/t (Std. daf), respectively.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号