共查询到20条相似文献，搜索用时 390 毫秒
1.
Mohamed Ashour Gary M. Norris Sherif Elfass Ashraf Z. Al-Hamdan 《Computers and Geotechnics》2010,37(7-8):858-866
This paper presents a procedure to assess the mobilized pile side and tip resistance versus pile head and tip settlement under axial load in clay soil. The load transfer (t–z) curve is evaluated at any point on the loaded pile based on the combined pile tip/side resistance–displacement mechanisms along the length of the pile. Unlike current methods that assume the pile settlements as a percentage of the pile/shaft diameter, the presented technique determines the side and tip resistance of the pile and the associated pile settlement under existing load based on the current stress/strain level in the surrounding soil up to failure (excessive settlement). The technique employs the concepts of the elastic theory and Ramberg–Osgood characterization of the stress–strain behavior of the clay soil. Case studies are also presented to exhibit the capabilities of the proposed procedure. The good agreement between measured and calculated load transfer curves along the pile and pile tip resistance versus pile head, side, and tip displacements shows the consistency of the proposed procedure. A computer code is developed to employ the presented technique. 相似文献
2.
基于改进荷载传递法计算降水引起的基桩沉降 总被引：1，自引：0，他引：1
现有研究采用荷载传递法时均未计算桩体自重,若直接应用于国内软土地区超长桩基的沉降计算,其精度难以满足高速铁路线下工程严格的沉降控制要求。基于佐藤?悟双折线模型提出侧阻荷载传递函数的假定模式,引入桩体自重并对荷载传递法的基本微分方程进行修正和求解,结合降水引起的桩周土体沉降计算和基于端阻弹性模型的桩端土体沉降计算,获得地下水位变化诱发的基桩沉降计算方法;采用理论推导的基桩沉降解析解,并借助嵌入荷载传递函数的有限元方法,分别对单纯桩顶荷载作用和桩顶荷载与降水共同作用两种工况下的桩侧摩阻力、桩体轴力和基桩沉降进行算例对比分析;有限元计算因考虑了由桩体沉降产生的桩周土体附加竖向位移而与理论计算略有偏差,但两种方法计算结果的变化规律基本一致,验证了降水引起的基桩沉降理论计算公式的合理性及正确性。 相似文献
3.
This paper presents the analysis of creep settlement of pile groups for line pile groups, square pile groups, and rectangular pile groups undergoing creep settlements over a period of time. The soil is treated as a viscoelastic material and is modeled using a three-parameter viscoelastic model. The damping component (dashpot) takes care of the permanent time-dependent deformations in three-parameter viscoelastic model. An approach suggested by Mindlin has been employed to calculate the stress distribution along the pile length in a group. The viscoelastic problem is converted into an elastic problem by the application of Laplace transform. Results in the form of variation of interaction factors for parameters such as pile length to diameter ratio, pile spacing, Poisson's ratio, and modulus ratio have been presented. Comparison has been made between interaction factors for piles groups undergoing immediate settlements and creep settlements. Finally, a typical predictive example has been presented for a 3 × 3 pile group showing creep settlement. The load rearrangement due to creep settlements causes about 5% to 35% increase in base resistance over time. Interaction factors for pile groups (2 × 1, 3 × 1, 2 × 2, and 3 × 2) undergoing creep settlement is about 15% to 55% higher than the interaction factors considering only the immediate settlements for pile group spacing less than or equal to 5d. 相似文献
4.
考虑沉桩效应对桩周土体力学特性的影响,采用指数函数型荷载传递曲线分别建立了静压桩的桩侧和桩端荷载传递模型。在此基础上,根据群桩加载过程中桩周土体的变形模式,基于荷载传递法描述桩-土界面的非线性行为,采用剪切位移法考虑群桩之间的相互作用,提出了考虑沉桩效应的群桩非线性荷载-沉降混合计算方法。通过开展离心模型试验对该计算方法解答进行了验证,研究了沉桩效应和桩-土界面非线性特征对群桩承载特性的影响。研究结果表明,沉桩效应对桩周土体起到挤密作用,使得桩周土体的强度和刚度增大,从而提高了群桩的承载特性。群桩加载过程中桩-土界面刚度随沉降变形而逐渐减小,使得群桩荷载-沉降曲线呈现出明显的非线性特征。 相似文献
5.
M. F. Bransby 《国际地质力学数值与分析法杂志》1999,23(15):1909-1926
Two-dimensional finite element analysis has been used to find load–transfer relationships for translation of an infinitely long pile through undrained soil for a variety of soil-constitutive models. It has been shown that these load–transfer curves can be used as p–y curves in the analysis of single piles undergoing lateral pile head loading in undrained soils with non-linear stress–strain laws. Lateral pile response deduced from 2-D analysis input to the subgrade reaction method has been compared to the behaviour of a single pile analysed using three-dimensional finite element analysis. Good agreement between the two methods for non-linear soils suggests that the 2-D analysis may form a useful design method for calculation of p–y curves. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
6.
A modulus‐multiplier approach, which applies a reduction factor to the modulus of single pile p–y curves to account for the group effect, is presented for analysing the response of each individual pile in a laterally loaded pile group with any geometric arrangement based on non‐linear pile–soil–pile interaction. The pile–soil–pile interaction is conducted using a 3D non‐linear finite element approach. The interaction effect between piles under various loading directions is investigated in this paper. Group effects can be neglected at a pile spacing of 9 times the pile diameter for piles along the direction of the lateral load and at a pile spacing of 6 times the pile diameter for piles normal to the direction of loading. The modulus multipliers for a pair of piles are developed as a function of pile spacing for departure angle of 0, 90, and 180sup>/sup> with respect to the loading direction. The procedure proposed for computing the response of any individual pile within a pile group is verified using two well‐documented full‐scale pile load tests. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
7.
Osterberg-Cell (O-Cell) tests are widely used to predict the load–settlement behavior of large-diameter drilled shafts socketed in rock. The loading direction of O-Cell tests for shaft resistance is opposite to that of conventional downward load tests, meaning that the equivalent top load–settlement curve determined by the summation of the mobilized shaft resistance and end bearing at the same deflection neglects the pile-toe settlement caused by the load transmitted along the pile shaft. The emphasis is on quantifying the effect of coupled shaft resistance, which is closely related to the ratios of pile diameter to soil modulus (D/Es) and total shaft resistance to total applied load (Rs/Q) in rock-socketed drilled shafts, using the coupled load-transfer method. The proposed analytical method, which takes into account the effect of coupled shaft resistance, was developed using a modified Mindlin’s point load solution. Through comparisons with field case studies, it was found that the proposed method reasonably estimated the load-transfer behavior of piles and coupling effects due to the transfer of shaft shear loading. These results represent a significant improvement in the prediction of load–settlement behaviors of drilled shafts subjected to bi-directional loading from the O-Cell test. 相似文献
8.
In this article, we present the solutions for the stresses induced by four different loads associated with an axially loaded pile in a continuously inhomogeneous cross‐anisotropic half‐space. The planes of cross‐anisotropy are parallel to the horizontal surface of the half‐space, and the Young's and shear moduli are assumed to vary exponentially with depth. The four loading types are: an embedded point load for an end‐bearing pile, uniform skin friction, linear variation of skin friction, and non‐linear parabolic variation of skin friction for a friction pile. The solutions for the stresses due to the pile load are expressed in terms of the Hankel integral and are obtained from the point load solutions of the same inhomogeneous cross‐anisotropic half‐space which were derived recently by the authors (Int. J. Rock Mech. Min. Sci. 2003; 40 (5):667–685). A numerical procedure is proposed to carry out the integral. For the special case of homogeneous isotropic and cross‐anisotropic half‐space, the stresses predicted by the numerical procedure agree well with the solutions of Geddes and Wang (Geotechnique 1966; 16 (3):231–255; Soils Found. 2003; 43 (5):41–52). An illustrative example is also given to investigate the effect of soil inhomogeneity, the type and degree of soil anisotropy, and the four different loading types on the vertical normal stress. The presented solutions are more realistic in simulating the actual stratum of loading problem in many areas of engineering practice. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
9.
超大面积深厚软土桩-网复合地基承载性状模型试验研究 总被引：1，自引：0，他引：1
基于厦深铁路潮汕车站地基处理加固工程,完全参照原型的软土地基地层分布情况,设计了两种不同桩间距下的超大面积深厚软土桩-网复合地基物理模型试验,对荷载传递机制与不同桩间距下桩体荷载分担比、桩土应力比及地基沉降规律等进行了系统研究。结果表明,桩身轴力沿着桩身高度往下先逐渐增大到某一深度后又逐渐减小,随着桩间距增大,桩承担上部荷载的方式由摩擦桩逐渐向端承桩变化;随着桩间距增大,桩身中性点下移,桩身最大负摩阻力出现的位置下降,且其值减小;桩间距对桩-土应力比有显著影响,而对桩体荷载分担比影响较小;不同桩间距下,两桩中心桩间土与桩顶差异沉降均小于4桩中心桩间土与桩顶差异沉降;随着路堤填土荷载增加,土工格栅表现为拉应变逐渐增大,拉应变曲线刚开始比较平缓,后逐渐变陡,增大的速率先慢后快。 相似文献
10.
11.
12.
Analytical solutions are developed for the prediction of the load–settlement response of a compressible axially loaded cast in situ pile in rock. The principal input parameters are derived from the τ–z curve which applies to the contact zone between the pile shaft and the embedment material. For larger diameter piles in rock, these τ–z curves can differ markedly from curves that apply to piles in clay and may include a significant strain hardening region prior to reaching peak strength. In addition to the complete analyses which would normally require the use of a computer, simplified solutions suitable for hand calculations have been derived for the peak load and the pile head displacement to peak. An example of the application of these simplified design calculations is presented. 相似文献
13.
This study presents a finite element (FE) micromechanical modelling approach for the simulation of linear and damage‐coupled viscoelastic behaviour of asphalt mixture. Asphalt mixture is a composite material of graded aggregates bound with mastic (asphalt and fine aggregates). The microstructural model of asphalt mixture incorporates an equivalent lattice network structure whereby intergranular load transfer is simulated through an effective asphalt mastic zone. The finite element model integrates the ABAQUS user material subroutine with continuum elements for the effective asphalt mastic and rigid body elements for each aggregate. A unified approach is proposed using Schapery non‐linear viscoelastic model for the rate‐independent and rate‐dependent damage behaviour. A finite element incremental algorithm with a recursive relationship for three‐dimensional (3D) linear and damage‐coupled viscoelastic behaviour is developed. This algorithm is used in a 3D user‐defined material model for the asphalt mastic to predict global linear and damage‐coupled viscoelastic behaviour of asphalt mixture. For linear viscoelastic study, the creep stiffnesses of mastic and asphalt mixture at different temperatures are measured in laboratory. A regression‐fitting method is employed to calibrate generalized Maxwell models with Prony series and generate master stiffness curves for mastic and asphalt mixture. A computational model is developed with image analysis of sectioned surface of a test specimen. The viscoelastic prediction of mixture creep stiffness with the calibrated mastic material parameters is compared with mixture master stiffness curve over a reduced time period. In regard to damage‐coupled viscoelastic behaviour, cyclic loading responses of linear and rate‐independent damage‐coupled viscoelastic materials are compared. Effects of particular microstructure parameters on the rate‐independent damage‐coupled viscoelastic behaviour are also investigated with finite element simulations of asphalt numerical samples. Further study describes loading rate effects on the asphalt viscoelastic properties and rate‐dependent damage behaviour. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
14.
15.
The yield vertex non‐coaxial theory is implemented into a critical state soil model, CASM (Int. J. Numer. Anal. Meth. Geomech. 1998; 22 :621–653) to investigate the non‐coaxial influences on the stress–strain simulations of real soil behaviour in the presence of principal stress rotations. The CASM is a unified clay and sand model, developed based on the soil critical state concept and the state parameter concept. Without loss of simplicity, it is capable of simulating the behaviour of sands and clays within a wide range of densities. The non‐coaxial CASM is employed to simulate the simple shear responses of Erksak sand and Weald clay under different densities and initial stress states. Dependence of the soil behaviour on the Lode angle and different plastic flow rules in the deviatoric plane are also considered in the study of non‐coaxial influences. All the predictions indicate that the use of the non‐coaxial model makes the orientations of the principal stress and the principal strain rate different during the early stage of shearing, and they approach the same ultimate values with an increase in loading. These ultimate orientations are dependent on the density of soils, and independent of their initial stress states. The use of the non‐coaxial model also softens the shear stress evolutions, compared with the coaxial model. It is also found that the ultimate shear strengths by using the coaxial and non‐coaxial models are dependent on the plastic flow rules in the deviatoric plane. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
16.
17.
A large strain analysis of undrained expansion of a spherical/cylindrical cavity in a soil modelled as non‐linear elastic modified Cam clay material is presented. The stress–strain response of the soil is assumed to obey non‐linear elasticity until yielding. A power‐law characteristic or a hyperbolic stress–strain curve is used to describe the gradual reduction of soil stiffness with shear strain. It is assumed that, after yielding, the elasto‐plastic behaviour of the soil can be described by the modified Cam clay model. Based on a closed‐form stress–strain response in undrained condition, a numerical solution is obtained with the aid of simple numerical integration technique. The results show that the stresses and the pore pressure in the soil around an expanded cavity are significantly affected by the non‐linear elasticity, especially if the soil is overconsolidated. The difference between large strain and small strain solutions in the elastic zone is not significant. The stresses and the pore pressure at the cavity wall can be expressed as an approximate closed‐form solution. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
18.
A simplified method of numerical analysis based on elasticity theory has been developed for the analysis of axially and laterally loaded piled raft foundations embedded in non‐homogeneous soils and incorporated into a computer program “PRAB”. In this method, a hybrid model is employed in which the flexible raft is modelled as thin plates and the piles as elastic beams and the soil is treated as springs. The interactions between structural members, pile–soil–pile, pile–soil–raft and raft–soil–raft interactions, are approximated based on Mindlin's solutions for both vertical and lateral forces with consideration of non‐homogeneous soils. The validity of the proposed method is verified through comparisons with some published solutions for single piles, pile groups and capped pile groups in non‐homogeneous soils. Thereafter, the solutions from this approach for the analysis of axially and laterally loaded 4‐pile pile groups and 4‐pile piled rafts embedded in finite homogeneous and non‐homogeneous soil layers are compared with those from three‐dimensional finite element analysis. Good agreement between the present approach and the more rigorous finite element approach is demonstrated. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
19.
Creep settlements are the main cause of deterioration of road pavement and impervious elements of dams, and therefore a method to calculate them is needed. Viscoelastic models (e.g. the standard linear solid) have been chosen to represent the creep of granular materials (Figure 1). Finite element calculations show that quasi‐oedometric conditions exist near the centre of embankments. Explicit expressions for one‐dimensional viscoelastic settlements of an embankment during and after construction have been obtained for any loading law and drawn for a linear load. The three viscoelastic parameters, Eo, Rc and Tr can be determined through laboratory or field testing, and the results can be adjusted by using settlement records. Good agreement has been found between measured and calculated settlements at several dams. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
20.
Pile foundations are frequently subjected to cyclic lateral loads. Wave and wind loads on offshore structures will be applied in different directions and times during the design life of a structure. Therefore, the magnitude and direction of these loads in conjunction with the dead loads should be considered. This paper investigates a loading scenario where a monotonic lateral load is applied to a pile, followed by two‐way cycling in a direction perpendicular to the initial loading. This configuration is indicative of the complexity of loading that may be considered and is referred to in the paper as ‘T‐shaped’ loading. The energy‐based numerical model employed considers two‐dimensional lateral loading in an elasto‐plastic soil, with coupled behaviour between the two perpendicular directions by local yield surfaces along the length of the pile. The behaviour of the soil–pile system subjected to different loading combinations has been divided into four categories of shakedown previously proposed for cyclic loading of structures and soils. A design chart has been created to illustrate the type of pile behaviour for a given two‐dimensional loading scenario. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献