首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 968 毫秒
1.
This is the first part of a study on the seismic response of the L’Aquila city using 2D simulation and experimental data. We have studied two velocity-depth models with the aim of outlining the behavior of a velocity reversal in the top layer, which is associated with the stiff Brecce de L’Aquila unit (BrA). In this setting, the SMTH model is topped by a layer with about 2:1 impedance contrast with the underlying layer while the NORV model has no velocity reversal. We have simulated the propagation of SH and P-SV wavefields in the range 0–10 Hz for incidence 0°–90°. Earthquake spectral ratios of the horizontal and vertical components at six sites in L’Aquila downtown are compared to corresponding synthetics spectral ratios. The vertical component of P-SV synthetics enables us to investigate a remarkable amplification effect seen in the vertical component of the recorded strong motion. Sites AQ04 and AQ05 are best matched by synthetics from the NORV model while FAQ5 and AQ06 have a better match with synthetics spectral ratios from the SMTH model. All simulations show this behavior systematically, with horizontal and near-horizontal incident waves predicting the overall pattern of matches more clearly than vertical and near-vertical incidence. The model inferences are in agreement with new geological data reporting lateral passages in the top layer from the stiff BrA to softer sediments. Matches are good in terms of frequency of the first amplification peak and of spectral amplitude: the horizontal components have spectral ratio peaks predominantly at 0.5 Hz in the simulations and at 0.7 Hz in the data, both with amplitudes of 4, while the vertical component spectral ratios reach values of 6 at frequencies of about 1 Hz in both data and simulations. The vertical component spectral ratios are very well matched using Rayleigh waves with incidence at 90°. The NORV model without the velocity reversal predicts spectral ratio peaks for the horizontal components at frequencies up to 6 Hz. The reversal of velocity acts as a low-pass frequency filter on the horizontal components reducing the amplification effect of the sediment filled valley.  相似文献   

2.
The 2009 Mw 6.3 L’Aquila event caused extensive damage in the city of L’Aquila and in some small towns in its vicinity. The most severe damage was recognized SE of L’Aquila town along the Aterno river valley. Although building vulnerability and near-source effects are strongly responsible for the high level of destruction, site effects have been invoked to explain the damage heterogeneities and the similarities between the 2009 macroseismic field with the intensities of historical earthquakes. The small village of Onna is settled on quaternary alluvium and suffered during the L’Aquila event an extremely heavy damage in the masonry structures with intensity IX–X on the Mercalli-Cancani-Sieberg (MCS) scale. The village of Monticchio, far less than 1.3 km from Onna, is mostly situated on Mesozoic limestone and suffered a smaller level of damaging (VI MCS). In the present paper, we analyze the aftershock recordings at seismic stations deployed in a small area of the middle-Aterno valley including Onna and Monticchio. The aim is to investigate local amplification effects caused by the near-surface geology. Because the seismological stations are close together, vulnerability and near-source effects are assumed to be constant. The waveform analysis shows that the ground motion at Onna is systematically characterized by large high-frequency content. The frequency resonance is varying from 2 to 3 Hz and it is related to alluvial sediments with a thickness of about 40 m that overlay a stiffer Pleistocene substrate. The ground motion recordings of Onna are well reproduced by the predictive equation for the Italian territory.  相似文献   

3.
We exploit S-wave spectral amplitudes from 112 aftershocks (3.0 ≤ ML ≤ 5.3) of the L’Aquila 2009 seismic sequence recorded at 23 temporary stations in the epicentral area to estimate the source parameters of these events, the seismic attenuation characteristics and the site amplification effects at the recording sites. The spectral attenuation curves exhibit a very fast decay in the first few kilometers that could be attributed to the large attenuation of waves traveling trough the highly heterogeneous and fractured crust in the fault zone of the L’Aquila mainshock. The S-waves total attenuation in the first 30 km can be parameterized by a quality factor QS(f) = 23f 0.58 obtained by fixing the geometrical spreading to 1/R. The source spectra can be satisfactorily modeled using the omega-square model that provides stress drops between 0.3 and 60 MPa with a mean value of 3.3±2.8 MPa. The site responses show a large variability over the study area and significant amplification peaks are visible in the frequency range from 1 to more than 10 Hz. Finally, the vertical component of the motion is amplified at a number of sites where, as a consequence, the horizontal-to-vertical spectral ratios (HVSR) method fails in detecting the amplitude levels and in few cases the resonance frequencies.  相似文献   

4.
On April 6, 2009, the town of L’Aquila in the Abruzzo region (central Italy) was struck by a seismic event at 01:32 (UTC), of magnitude MW = 6.3. The mainshock was followed by a long period of intense seismic activity and within seven days after the mainshock there were seven events of magnitude MW ≥ 5 that occurred from April 6 to April 13. This long seismic sequence was characterized by a complex rupture mechanism that involved two major normal faults of the central Apennines: the Paganica and the Gorzano faults. The strong-motions of the mainshock were recorded by 64 stations of the Italian Strong-motion Network (RAN) operated by the National Civil Protection Department (DPC). Six stations of a local strong-motion array were working in NW L’Aquila suburb area. One of them, located at about 6 km from the Paganica fault surface tip-line, set up in trigger mode, recorded continuously for more than 20 min the mainshock and the aftershocks. Besides the mainshock, the RAN stations recorded in total 78 foreshocks and aftershocks of ML ≥ 3.5, during the period from January to December 2009. The corresponding waveforms provide the most extensive digital strong ground motion data set ever recorded in Italy. Moreover, the 48 three-component observations of events of magnitude MW ≥ 5, recorded at a distance less than 15 km from each of the major involved faults, provide a significant increasing of near-field records available for the Italian territory. Six days after the mainshock, the strong-motion dataset, referred to preliminary locations of the events with ML ≥ 4.0, was made available on the DPC web site () and at the same time it was delivered to the ITACA database (). This dataset has been used by many authors in scientific papers and by engineers, geophysicists and geologists for professional technical works. In this paper, the present-day available strong-motion signals from the L’Aquila sequence and the performance of the Italian strong-motion network in terms of the number and quality of recorded data, the geometry and data transmission system are described. In addition the role of the temporary network that represents an extension of the permanent Italian strong-motion network, supporting the emergency response by civil protection authorities and improving the network coverage has been evaluated.  相似文献   

5.
In the present work the seismic site response of Narni ridge (Central Italy) is evaluated by comparing experimental results and numerical simulations. The inhabited village of Narni is located in central Apennines at the top of a steep massive limestone ridge. From March to September 2009 the site was instrumented with 10 weak-motion stations, 3 of which located at the base of the ridge and 7 at the top. The velocimetric network recorded 642 events of ML up to 5.3 and hypocentral distance up to about 100 km. The great amount of data are related to the April 2009 L’Aquila sequence. The site response was analyzed using both reference (standard spectral ratio, SSR) and non reference spectral techniques (horizontal to vertical spectral ratio, HVSR). Moreover directional analyses were performed in order to evaluate the influence of the ridge orientation with respect to the selected source-site paths. In general the experimental results show amplification factors for frequencies between 4 and 5 Hz for almost all stations installed along the crest. The SSR technique provides amplification factors up to 4.5 in a direction perpendicular to the main elongation of the ridge. The results obtained from the data analyses were used as a target for bidimensional and tridimensional numerical simulations, performed using a hybrid finite-boundary element method and a boundary element method for 2D and 3D modelling, respectively. In general, the results obtained through numerical simulation fit well the experimental data in terms of range of amplified frequencies, but they underestimate by a factor of about 2 the observed amplifications.  相似文献   

6.
On 6 April 2009 a Mw=6.1 earthquake produced severe destruction and damage over the historic center of L’Aquila City (central Italy), in which the accelerometer stations AQK and AQU recorded a large amount of near-fault ground motion data. This paper analyzes the recorded ground motions and compares the observed peak accelerations and the horizontal to vertical response spectral ratios with those revealed from numerical simulations. The finite element method is considered herein to perform dynamic modeling on the soil profile underlying the seismic station AQU. The subsurface model, which is based on the reviewed surveys that were carried out in previous studies, consists of 200–400 m of Quaternary sediments overlying a Meso-Cenozoic carbonate bedrock. The Martin-Finn-Seed's pore-water pressure model is used in the simulations. The horizontal to vertical response spectral ratio that is observed during the weak seismic events shows three predominant frequencies at about 14 Hz, 3 Hz and 0.6 Hz, which may be related to the computed seismic motion amplification occurring at the shallow colluvium, at the top and base of the fluvial-lacustrine sequence, respectively. During the 2009 L’Aquila main shock the predominant frequency of 14 Hz shifts to lower values probably due to a peculiar wave-field incidence angle. The predominant frequency of 3 Hz shifts to lower values when the earthquake magnitude increases, which may be associated to the progressive softening of soil due to the excess pore-water pressure generation that reaches a maximum value of about 350 kPa in the top of fluvial-lacustrine sequence. The computed vertical peak acceleration underestimates the experimental value and the horizontal to vertical peak acceleration ratio that is observed at station AQU decreases when the earthquake magnitude increases, which reveals amplification of the vertical component of ground motion probably due to near-source effects.  相似文献   

7.
The 1897 Great Shillong earthquake revealed considerable seismic susceptibility in Guwahati City, such as soil liquefaction, landslides, and surface fissures. In an attempt to quantify the seismic vulnerability of the city based on geological, seismological, and geotechnical aspects concerning seismic site characterization, in-depth analysis was performed using a microtremor survey with recordings of five small to moderate magnitude (4.8 ≤ mb ≤ 5.4) earthquakes that occurred in 2006 and geotechnical investigations using the Standard Penetration Test (SPT). Additionally, the basement topography was established using vertical electrical resistivity sounding and selected drill-hole information. Region-specific relationships are derived by correlating the estimated values of predominant frequency, shear-wave velocity, and basement depth indicating conformity with the predominant frequency distribution and the basin topography underlain by a hard granitic basement. Most parts of the city adhere to the predominant frequency range of 0.5–3.5 Hz, setting aside areas of deep sediment fills or hilly tracts, suggesting that the existing moderate-rise RC buildings in the territory are seismically vulnerable. Furthermore, the geotechnical assessment of the soil liquefaction potential reveals widespread susceptibility across the terrain. Eventually, a site classification map of the city is prepared following the National Earthquake Hazard Program (NEHRP) provision. The average site amplification factor from geotechnical modeling for site class D is about 3 in the frequency range of 2–4 Hz. In addition, earthquake data yield an average site amplification factor of 4–6 in the frequency range of 1.2–5.0 Hz at the seismic stations located in site class E and F. High site amplifications of around 5.5 and 7.5 at 2 Hz, respectively, are observed at AMTRON and IRRIG seismic stations, which are located in the proximity of Precambrian rocks, indicating probable basin edge effects—scattering and diffraction of incident energy. Interplay of dispersed valleys surrounded by small hillocks in the study region is likely to induce micro-basin effects where the sediment thickness/depth vis-à-vis predominant frequency and basin geometry in conjunction play pivotal roles in the augmentation of site response.  相似文献   

8.
In this work, we investigate the site amplification effects observed in the Norcia plain, Central Italy. Data from 30 selected local earthquakes (2 ≤ Ml ≤ 4.1) recorded by a temporary seismic network composed by 15 stations, are analyzed to determine the spatial variability of site effects. Both the Horizontal-to-Vertical spectral ratio and the Standard Spectral Ratio techniques are applied to estimate the site amplification effects. The results show that most of the sites in the valley are affected by strong amplifications (up to a factor of 20) in the frequency range 0.5–5 Hz. The value of the fundamental frequency of resonance is strictly dependent on the location within the basin and on the sediment thickness. Strong amplifications also affect the vertical components. The time-frequency analysis performed on a station located inside the basin shows the presence of a large spectral amplitudes after the S-wave phase, not observed on a station located on the bedrock, suggesting the presence of locally generated wave trains. Then, in agreement with earlier observations for other alluvial basins in Central Italy, 2D–3D effects play an important role in determining the site amplification effects in Norcia.  相似文献   

9.
Ground motion for the 6 April 2009 (Mw 6.3) earthquake is computed along 2-D cross-sections at L’Aquila by a hybrid method (modal summation plus finite differences) and validated with recordings at AQU, AQK, AQG, AQA and AQV stations. Parametric studies of S-wave velocities of the shallowest lithotypes allow to get a general agreement between synthetic and observed response spectra, despite the scaled point-source approach and the lack of detailed geological and seismic studies. It results that the megabreccia covering on lacustrine soils, characterizing the historical center of L’Aquila, is responsible of spectral amplifications along the vertical (2–7) and horizontal components (2–3) at a wide frequency range (0.6–7 Hz). The covering of alluvial soils in the middle Aterno river valley is responsible of amplifications at 2–7 Hz both in the horizontal and vertical planes of the motion. Such amplifications evidence that site effects might have been responsible of structural damages.  相似文献   

10.
The M w 6.3 L’Aquila earthquake of April 6, 2009 hit a wide area of the Abruzzo region (Central Italy). The epicentre of the main shock was very close to the urban centre of L’Aquila, the regional capital, with an epicentral distance less than 10 km. It was the strongest earthquake ever recorded in Italy which has provided ground motion recordings from accelerometric stations located in close proximity to the epicentre. Because of this, several remarkable results can be achieved by analysing the strong motion recorded signals in terms of peak (PGA, PGV and PGD) and integral (Housner Intensity, I H) seismic parameters. Additionally, an alternative time-domain representation of recorded signals has been used to furnish a rapid comparison of traces recorded at different stations and along different directions. Some comparisons between the response spectra derived from the recordings and the elastic demand spectra provided in the new seismic Italian code have also been performed. PGA recorded values are very high and generally higher than code values for seismic actions with return period T R = 475 years. In some cases, this also happens for seismic actions with T R up to 2,475 years. With regard to I H, recorded values are generally higher for T R = 475 years, whilst they are remarkably lower for T R = 2,475 years. Accurate analyses have been carried out in the article to better understand the above differences and their significance and implications.  相似文献   

11.
After the April 6th 2009 L’Aquila earthquake (M w 6.3), where 306 people died and a further 60,000 were displaced, seismic microzoning investigations have been carried out for towns affected by a macroseismic intensity equal to or greater than 7 MCS. Based upon seismotectonic data, historical seismicity and strong motion records, we defined input spectra to be used in the numerical simulations of seismic microzoning in four key municipalities, including the town of L’Aquila. We adopted two main approaches: uniform hazard response spectra are obtained by a probabilistic seismic hazard assessment introducing some time-dependency for individual faults on the study area; a deterministic design spectrum is computed from magnitude/distance pairs extracted by a stationary probabilistic analysis of historical intensities. The uniform hazard spectrum of the present Italian building code represents the third, less restrictive, response spectrum to be used for the numerical simulations in seismic microzoning. Strong motions recordings of the main shock of the L’Aquila sequence enlighten the critical role played by both the local response and distances metric for sites located above a seismogenic fault; however, these time-histories are compatible with the uncertainties of a deterministic utilization of ground motion predictive equations. As recordings at very near field are rare, they cannot be neglected while defining the seismic input. Disaggregation on the non-Possonian seismotectonic analysis and on the stationary site-intensity estimates reach very similar results in magnitude-distance pairs identification; we interpret this convergence as a validation of the geology-based model by historical observations.  相似文献   

12.
The April 6, 2009 L’Aquila earthquake was responsible for an “anomalous”, relatively high degree of damage (i.e. Is 7 MCS scale) at Castelvecchio Subequo (CS). Indeed, the village is located at source-to-site distance of about 40 km, and it is surrounded by other inhabited centres to which considerably lower intensities, i.e. Is 5–6, have been attributed. Moreover, the damage was irregularly distributed within CS, being mainly concentrated in the uppermost portion of the old village. Geophysical investigations (ambient seismic noise and weak ground motions analyses) revealed that site effects occurred at CS. Amplifications of the ground motion, mainly striking NE–SW, have been detected at the uppermost portion of the carbonate ridge on which the village is built. Geological/structural and geomechanical field surveys defined that the CS ridge is affected by sets of fractures, joints and shear planes—mainly roughly NW–SE and N–S trending—that are related to the deformation zone of the Subequana valley fault system and to transfer faults linking northward the mentioned tectonic feature with the Middle Aterno Valley fault system. In particular, our investigations highlight that seismic amplifications occur where joints set NW–SE trending are open. On the other hand, no amplification is seen in portions of the ridge where the bedrock is densely fractured but no open joints occur. The fracture opening seems related to the toppling tendency of the bedrock slabs, owing to the local geomorphic setting. These investigations suggest that the detected amplification of the ground motion is probably related to the polarization of the seismic waves along the Castelvecchio Subequo ridge, with the consequent oscillation of the rock slabs perpendicularly to the fractures azimuth.  相似文献   

13.
In San Gregorio (L’Aquila, Italy) a three-story, reinforced concrete (RC) building had the first floor collapsed following the earthquake of April 6, 2009. The remaining two stories fell with a displacement in the horizontal projection of about 70 cm. This unusual behaviour is made more puzzling by the fact that buildings located at a short distance and with similar features had little or no damage reported. To understand the causes of the collapse we performed strong motion recordings, microtremor measurements, a detailed geological survey, a high-resolution geo-electrical tomography, a borehole with a down-hole test. On the building we performed a geometrical survey and laboratory tests on concrete cores. The acceleration and noise recordings have shown a high amplification with uphill-downhill direction. The geological survey has revealed the presence of co-seismic fractures on stiff soils. Geo-electrical tomography has shown an unexpected, strong discontinuity just below the building. Taking advantage of excavations in adjacent lots, we have highlighted rare cataclastic decimetric bands with a very low resistance material incorporated in well-stratified calcarenites. The same soft material has been founded in the borehole down to 17 m from ground level, showing a shear wave velocity that starts at 250 m/s, increases with depth and has an abrupt transition in calcarenites at 1,150 m/s. The surface geophysical measurements in the vicinity of the site have not shown similar situations, with flat HVSR curves as expected for a rock outcrop, except for a lateral extension of the soft zone. The analysis on the quality of the building materials has yielded values higher than average for the age and type of construction, and no special design or construction deficiencies have been observed. A strong, peculiar site effect thus appears to be the most likely cause of the damage observed.  相似文献   

14.
During the microzonation studies of the April 6th, 2009 L??Aquila earthquake, we observed local seismic amplifications in the Roio area??a plane separated from L??Aquila city center by mount Luco. Six portable, digital instruments were deployed across the plain from 15 April to mid-May 2009. This array recorded 152 aftershocks. We analyzed the ground motion from these events to determine relative site amplification within the plain and on surrounding ridges. Horizontal over vertical spectral ratio on noise data (HVSRN), aftershock recordings (HVEQ) and standard spectral ratio (SSR) showed amplifications at 1.3 and 4.0?Hz on quaternary deposits. Seismic amplifications in the frequency range of 4 and 6?Hz were also observed on a carbonate ridge of Colle di Roio, on the northwestern border of the plateau. A small amplification was noticed near the top of mount Luco, another rocky site. Large discrepancies in the amplification levels between methods have been observed for these sites, but the HVSRN, HVEQ and SSR gave similar results at the stations located in the Roio plain. On the rocky sites, the SSR was more reliable than the HVSRN at estimating the transfer function of the site, even if the resonance frequency seemed to be well detected by the latter method.  相似文献   

15.
In order to determine the fundamental period of soil vibrations in Cairo, 174 microtremors stations, in conjunction with mobile accelerographs, were used. The result was a collection of long-period microtremors and ambient noise arising from cultural disturbances. The Nile Valley shows some fixed peaks at 2.5–3.5 Hz at the center of the basin, while the Nile’s surrounding area shows a fundamental peak of 4–5 Hz, leaving a 5–7-Hz resonance peak for the sand-like, gravelly soil from Abbasiya to the airport. A frequency-dependent soil amplification map is drawn, which includes seismic microzonation maps for Cairo. Based on the above, a maximum acceleration map for two important earthquakes affecting Egypt in the last century is produced (Faiyum, 1992, and Aqaba, 1995).  相似文献   

16.
Previous works based mainly on strong-motion recordings of large Japanese earthquakes showed that site amplification and soil fundamental frequency could vary over long and short time scales. These phenomena were attributed to non-linear soil behaviour: the starting fundamental frequency and amplification were both instantaneously decreasing and then recovering for a time varying from few seconds to several months. The recent April 6, 2009 earthquake (M W 6.3), occurred in the L’Aquila district (central Italy), gave us the possibility to test hypotheses on time variation of amplification function and soil fundamental frequency, thanks to the recordings provided by a pre-existing strong-motion array and by a large number of temporary stations. We investigated the intra- and inter-event soil frequency variations through different spectral analyses, including time-frequency spectral ratios and S-Transform (Stockwell et al. in IEEE Trans Signal Process 44:998–1001, 1996). Finally, analyses on noise recordings were performed, in order to study the soil behaviour in linear conditions. The results provided puzzling evidences. Concerning the long time scale, little variation was observed at the permanent stations of the Aterno Valley array. As for the short time-scale variation, the evidence was often contrasting, with some station showing a time-varying behavior, while others did not change their frequency with respect to the one evaluated from noise measurements. Even when a time-varying fundamental frequency was observed, it was difficult to attribute it to a classical, softening non-linear behaviour. Even for the strongest recorded shocks, with peak ground acceleration reaching 0.7 g, variations in frequency and amplitude seems not relevant from building design standpoint. The only exception seems to be the site named AQV, where the analyses evidence a fundamental frequency of the soil shifting from 3 Hz to about 1.5 Hz during the mainshock.  相似文献   

17.
After the 2009 April 6th Mw 6.3 L??Aquila earthquake (Central Italy) the Italian Civil Defense Department promoted the microzoning study in the ten zones in the epicentral area that suffered major damage. In this paper we present the activities and the results concerning a temporary seismic network installed in the historical L??Aquila city center indicated as ??macroarea 1?? in the microzoning project. Seismic data were collected to investigate the amplification effects in the city and to support the microzoning activities in verifying both geological profiles and 1D numerical modeling of the seismic response of the city. The conventional spectral approaches using both microtremor and earthquake data allowed to determine the fundamental resonance frequencies and the amplification factors within the city respectively. The spatial variability of these quantities can be related to the geological and geomorphologic characteristics of the investigated area. A comparison between the network data and the data recorded by the two strong motion instruments installed in the city was also made. This allows verifying the relative response of the accelerometric stations that recorded in the city the major events of the sequence.  相似文献   

18.
Shear-wave splitting in the southeast of Cathaysia block, South China   总被引：2，自引：0，他引：2  
This study is focused on Fujing Province in China, southeast of Cathaysia block (SECB). The present work benefits from the data provided by the Fujian Seismic Network (FJSN) to study the seismic anisotropy in the crust. By means of a systematic analysis and adequate software package, we examine shear-wave splitting from data recorded at ten FJSN stations during the period January 1999 to December 2003. The results demonstrate that the average fast wave polarization is N109.4° E ± 42.6°, corresponding to the horizontal principal compressive stress in the test zone, and the average normalized slow wave time delay is 2.5 ± 1.5 ms/km. The predominant polarizations at stations in the eastern part of SECB are in the N–W direction, which suggests that they are related to the regional horizontal principal compressive stress and also to the strikes of faults. In contrast, the predominant polarizations at two stations in the western part of SECB are in the N–E direction. This polarization direction does not coincide with the direction of the horizontal principal compressive stress, but it follows the strikes of near faults, thus suggesting the influence of the local tectonics and a change in the stress field. The results prove that the predominant polarizations are parallel to the strikes of faults whenever the stations are on active faults. At a few stations near the coastal line, some polarizations show a certain amount of scatter which may be caused by crossing faults and irregular topography. Finally, the spatial distribution of time delays depicts strong lateral variations near the coast just where the seismic activity is comparatively bigger, so that the magnitude of anisotropy seems to be consistent with the most seismically active area.  相似文献   

19.
The determination of seismic amplitude amplification is a fundamental contribution to seismic hazard assessment. While often only high-frequency amplitude variations (>1 Hz) are taken into account, we analyse broadband waveforms from 0.14 to 8.6 Hz using a temporary network of 32 stations in and around the earthquake-prone city of Bucharest. Spectral amplitudes are calculated with an adaptive multiple-taper approach. Across our network (aperture 25 km × 25 km), we find a systematic northwest/southeast-oriented structural influence on teleseismic P-wave amplitudes from 0.14 to 0.86 Hz that can be explained by constructive interference in the dipping Cenozoic sedimentary layers. For higher frequencies (1.4–8.75 Hz), more local site effects prevail and can be correlated partly among neighbouring stations. The transition between systematic and localised amplitude variations occurs at about 1 Hz.  相似文献   

20.
On April 6, 2009 a ML = 5.8 earthquake hit the city of L’Aquila on the Apennine chain in central Italy. Notwithstanding the moderate-size event the L’Aquila city and several small villages along the Aterno river valley suffered severe damage, because of the unusual strong motions, mainly due to proximity to the fault (estimated hypocentral depth of about 10 km). In this paper the main features of the recorded motion are discussed. Four accelerometric stations were located within the surface projection of the fault and recorded peak values ranging from 0.4 to 0.6 g. The recorded motions were characterised by short durations and high peak accelerations both in the horizontal and vertical directions. The strong portions of vertical and horizontal motions occurred almost simultaneously due to the short travel paths of P and S waves from the fault to the ground surface near the fault area. Hence site response analyses were performed for the sites where recording stations were located. The geotechnical subsoil model was derived by boreholes, in situ dynamic tests (D-H and SDMT) and by laboratory tests (RCT). One-dimensional numerical analyses were carried out employing the well known computer code EERA. The numerical model was calibrated, in the linear equivalent range, by comparing numerical results with the horizontal acceleration recorded components.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号