共查询到18条相似文献，搜索用时 156 毫秒
1.
《天文学进展》2019,(2)
天马望远镜的最高工作频段为43 GHz。为保证高质量的观测结果,需要研究风载荷对天线精度的影响。首先对观测站实测的风速风向数据做了统计分析,结果显示:10 m高度处10min时距平均风速小于4 m·s~(-1)的占比超过80%,主导风向为北-西北方向。然后,通过将倾斜仪实测结果与有限元模拟结果进行对比,验证了模拟的有效性,并进一步分析了在不同迎风姿态、不同风速下天线结构的平均风荷载响应,以及天线面形精度和指向精度的变化。结果表明,平均风荷载对天线指向精度,尤其是俯仰角指向精度的影响较大,对面形精度的影响较小;在弹性范围内,天线面形精度和指向精度与风速间均为二次关系。研究结果可为天线面形精度和指向精度的评估提供参考。 相似文献
2.
轮轨式天线的轨道作为承载整个天线重量的基础,其精度直接影响天线在方位方向运转的平稳性,引起天线轴系偏差从而影响天线的指向精度。介绍改造后的乌鲁木齐南山26 m射电望远镜(Nanshan Radio Telescope, NSRT)轨道结构以及轨道高差测量,并建立天线在不同方位、俯仰角下轨道高差引起天线指向偏差的数学模型。利用"十字扫描"法实测多颗标准源在相应位置的指向数据,并通过高斯拟合得到指向偏差。通过分析可知,轨道高差引起的指向偏差经过修正可以提高天线的指向精度。 相似文献
3.
佘山25米天线导轨问题对指向误差影响的研究 总被引：1，自引：1，他引：0
顾健星 《中国科学院上海天文台年刊》1994,(15):205-211
本根据25米射电望远镜方位导轨水平度的检测数据，分析了天线在不同位置时指向误差的情况及其原因，为进一步提高天线指向精度提供了理论依据和实测数据。 相似文献
4.
借助精密工程测量手段,对65 m天线背架的日照温度效应进行了实验研究.在天线背架设计坐标系下分析实验数据,建立了日照温度变形模型,得出背架结构沿X方向变形系数为Kx=1.30×10-5,沿Z方向变形系数为Kz=-0.44×10-5,沿Y方向变形偏向太阳照射一侧.根据实验数据建立的背架变形模型,模拟分析了65 m天线背架日照温度变形对面形精度的影响,得出环境温度变化1℃带来的面形精度(均方根值rms)影响分量约为0.09 mm.实验结果为65 m天线主动面调节提供了很有价值的参考数据. 相似文献
5.
本文对云南天文台十米射电望远镜的指向跟踪精度的影响因素做了比较详细的分析和讨论,提出了一些改进的措施,论证了天线系统指向精度达到33″、工作在1.3cm波段的可能性。 相似文献
6.
天马13 m射电望远镜是专为空间大地测量的新一代甚长基线干涉测量(Very Long Baseline Interferometry, VLBI)天线,即VGOS(VLBI Global Observing System)系统。VGOS观测将从调度、相关、观测策略到分析各方面改变甚长基线干涉测量。与传统测地观测相比,VGOS观测将数据精度提高1～2个数量级。天马13 m射电望远镜安装了3～15 GHz宽频制冷接收机,一般要求天线指向偏差小于最高频率波束宽度的1/10。为满足高精度指向要求,详细介绍了建立指向的方法和天线控制扫描策略,给出了系统误差修正模型的完全表达式,明确了指向修正模型中的参数意义。基于该天线指向扫描的实测数据,实测评估了望远镜的指向精度。采用最小二乘法对覆盖全天区的数据样本进行拟合,得到天马13 m射电望远镜指向模型,并加载到天线伺服控制系统进行验证,得到了优于10″的盲指误差。 相似文献
7.
射电望远镜的精度问题一直是国际天文界关注的热点。对于毫米波射电望远镜,温度变化引起的天线结构变形不容忽视,但是由于温度载荷的瞬时性和不确定性,很难对热变形进行准确分析和有效控制,因此,开展射电望远镜的热分析研究对提高望远镜的面形精度和指向精度具有重要意义。主要以代表性的全方位可动正馈和偏馈两类大型射电望远镜为研究对象,从理论、实验和模拟三个方面综述了射电望远镜热分析研究的现状,重点介绍了热分析的理论研究概况,并讨论了其中存在的问题,根据热分析研究的最新进展对其未来的发展趋势进行了展望。 相似文献
8.
随着射电望远镜口径增大、观测频率提高, 对其指向精度的要求也越来越高. 然而, 望远镜服役于野外台站, 台址风扰对天线指向精度的影响在高频段观测时已不能忽略. 由于风扰的时变性, 现有的抗风方法无法保障大口径高指向精度望远镜在高频段的有效观测时长. 因此, 提出了一种基于风障精确布置改善台址风环境的方法. 通过数值模拟构建了风障仿真模型, 并将仿真结果与风洞实测数据比较, 两种孔隙率风障的平均误差分别为3.7%和6.1%, 保证了风障模型的可靠性. 以新疆奇台射电望远镜(QiTai radio Telescope, QTT)台址为例, 基于QTT台址斜坡地形构建了计算域模型, 开展单风障不同高度、不同孔隙率的系列风场仿真试验, 得到了风障参量与下游挡风效果的关系. 基于单风障合理高度和最优孔隙率设置南北风障, 仿真结果表明在确定高度下最优孔隙率可以组合, 孔隙率0.1-0.1组合的风障挡风效果最优, 南方向来风在天线区域可以有效降低75%以上的风速. 相似文献
9.
射电望远镜天线结构设计和观测任务的正常进行都需要台址风场信息.随着望远镜性能要求的提高,天线结构设计越来越复杂,风载荷对天线观测时造成的指向影响也越发明显,如何在设计时保证结构刚度和强度,在观测时提高有效观测时间,都需要准确的风场数据.由于传统台址测风塔布置方法无法对测风塔拟设点的可靠性做出定量化评估,因此提出一种基于数值模拟优化测风塔位置的方法.数值模拟基于规范参数设置边界条件,与实测数据比较,整体趋势吻合,满足精度需求.对试验台址设置了4个测风塔位置,经分析P2点与天线位置的风速均方根误差值(root-mean-square error, RMSE)最小,测得的数据更能表征天线区域的风场特性. 相似文献
10.
《天文学报》2014,(3)
热变形是影响大型毫米波天线性能的关键因素之一.这种变形会改变天线反射面的轴线和焦距、恶化反射面面形,导致天线效率和指向精度恶化,同时也使天线效率和指向的长时间稳定性降低.由于太阳的周日运动,造成望远镜4个主支撑腿(简称支腿)之间存在温差,且该温差是变化的,从而引起方位轴的倾斜周期性变化.采用数字摄影测量、倾斜仪测量及天文实测等多种仪器和方法,研究了德令哈13.7m望远镜天线的热变形规律,并根据实时测量的主面温度分布,实现了副面自适应调焦补偿,使得天线效率提高近1倍.测量发现常规指向模型修正后的残差与天线主反射面(包括反射面板和背架,简称主面)直径方向温差存在线性相关性,故在指向解析模型中加入了温差修正项,并通过采用隔热材料包裹支腿的办法显著减小了支腿之间的温差,从而改善了望远镜的指向精度. 相似文献
11.
Wind field is a critical issue for radio telescope antenna structure design and observation. As the telescope performance requirements are getting higher and higher, the antenna structure design becomes more and more complicated, and the influence of wind load on antenna pointing in the observation is also serious. How to ensure the stiffness and strength of the structure during the design and to improve the effective observation time during the observation all need accurate wind field data. Due to the traditional wind tower setup method cannot quantitatively evaluate the reliability of the setting point position, so a method based on numerical simulation to optimize the position of the wind tower is proposed. The boundary conditions of numerical simulation are set based on specification parameters, the overall trend is consistent with the measured data, and therefore the simulation accuracy could meet the requirement. Four wind tower positions were set at the test site. According to the simulation results, the root-mean-square error (RMSE) of wind speed between point P2 and the antenna position is the smallest. So, the measured data in P2 could better represent the wind field characteristics of the antenna area. 相似文献
12.
针对大口径、高性能射电望远镜天线受到的随机及时变风扰的问题, 利用自回归滑动平均模型预测望远镜周围风速, 提前计算风致结构变形量, 同时为望远镜伺服控制系统提供足够执行时间来降低风扰影响. 基于新疆奇台110m口径全向可动射电望远镜(QiTai Telescope, QTT)台址风场数据特征, 通过赤池信息准则和贝叶斯信息准则辨识模型阶次, 利用最大似然法估计模型参数, 分析模型残差特性以检验自回归滑动平均模型的有效性. 通过计算不同季度预测数据与测试数据偏差得到预测模型的精度, 夏季平均绝对误差为0.133mcdots-1, 秋季平均绝对误差为0.162mcdots-1, 冬季平均绝对误差为0.287mcdots-1. 整体来看, 基于QTT台址不同季度风速数据建立的自回归滑动平均模型预测误差较小, 满足射电望远镜风扰控制系统的需求, 能为大口径射电望远镜风扰控制提供必要数据支撑. 相似文献
13.
LIU Xuan Aili Yusup Xiang Bin-bin Wang Cong-si XU Qian Wang Jun 《Chinese Astronomy and Astrophysics》2018,42(3):462-474
According to the influence mechanism of the antenna track irregularity on the telescope pointing accuracy, the distribution of the track errors and their influence on the pointing of the Urumqi Nanshan 26 m telescope are reanalyzed after the antenna track was reformed by using the whole-body welding technology, and hereby the pointing error model is correspondingly revised. By using the moving least-squares method, the measured height errors of the antenna track plane are fitted with a closed curve, and the tilt of the antenna azimuth axis caused by the track irregularity can be determined accordingly. Comparing it with the measured deviation of the antenna azimuth axis caused by the deformation of antenna pedestal, it can be found that both deviations are strongly correlated. A new pointing error model is established in view of the gravity deformation of antenna pedestal, which includes the north-south and east-west components, as well as the antenna track irregularity. Finally, by scanning a known calibration radio source at different positions in the sky, the measured pointing errors are fitted with the new pointing error model. The result shows that the sinusoidal component of the model error can be well constrained by the new pointing correction model, indicating that the new model can reflect very well the antenna pointing error, and can amend it to a certain extend. 相似文献
14.
First feed support system, which is one of the key technologies of Five hundred meter Aperture Spherical Telescope (FAST)
was discussed in this paper. A 1:30 scaled model (20 m × 20 m × 6 m) has been built to make systemic research on the feasibility
of the system. The root mean square of pointing error of moving cable car was measured and the displacements of cable car
within the wind speed of 8 m/s, which is the maximal wind speed of the place where the FAST will be located, were evaluated.
Then the total maximal pointing error of cable car was computed. Experimental results demonstrate that the total pointing
error of the cable car is less than 50 cm, the required pointing accuracy error of the system.
This revised version was published online in July 2006 with corrections to the Cover Date. 相似文献
15.
射电天线指向精度通常要求小于主波束宽度的1/10, 对于短厘米波段或毫米波段的大口径反射面天线, 指向精度要求高达几个角秒, 对于天线性能目标的实现是个巨大的挑战, 因此对于大口径高频段的反射面天线来说指向问题成为天线性能实现的重要关注焦点. 在众多影响天线指向精度的结构子系统因素中, 对主反射面变形因素的研究很少. 文章结合天线的结构特点建立了反射面空间坐标系统, 并基于变形后主面点的空间坐标值, 提出了3自由度下的非线性最小二乘吻合的方法去精准预测天线指向. 最后利用空间几何关系严格推导出了服务于天线指向误差修正的俯仰和方位的精确调整量, 从而构建了主面变形同指向误差之间的间接关系, 这对大型射电天线指向精度的提升具有一定的指导意义. 相似文献
16.
指向精度是大型射电望远镜天线具有挑战性的关键技术指标.在望远镜运行中,方位俯仰角的变化、重力以及日照等对副面撑杆的综合影响会引起望远镜的副面位姿改变从而引起指向误差的增加和天线效率的降低.基于天马65 m射电望远镜,使用位置传感器装置(PSD)法构建了副面位置偏移量测定系统,可以实时采集副面的3维位移数据,构建重力模型,将测试结果与射电法构建的现有副面模型进行对比,有较好的一致性.此外,该系统可以分析日照(引起撑腿局部温度效应)引起的副面位移情况,也可以监视风载和瞬时启停对副面位姿的影响. 相似文献
17.
MEI Geng-jun XIANG Bin-bin WANG Na WANG Zhao-jun 《Chinese Astronomy and Astrophysics》2021,45(2):236-251
The pointing accuracy of a radio telescope is usually less than one-tenth of its antenna beam width. For large-aperture antennas at the short-centimeter band or millimeter-wave band, the pointing accuracy must be as high as several arc seconds. Therefore, for large-diameter and high-frequency reflector antennas, the pointing problem has become an important focal point to realize the antenna performance. Among many structural subsystem factors that affect the antenna pointing accuracy, there has been only less study on the factor of main reflector deformation. Based on the structural characteristics of the antenna, a reflector space coordinate system is established in this paper. And based on the space coordinates of the main reflector surface points after deformation, a non-linear least squares fitting method with 3 degrees of freedom is proposed to accurately predict the antenna pointing. Finally, the space geometric relationship is used to strictly derive the precise adjustments on the elevation and azimuth in order for correcting the antenna pointing error, and the indirect relationship between the main reflector deformation and the pointing error is constructed. This has certain guiding significance for improving the pointing accuracy of large radio antennas. 相似文献
18.
《天文和天体物理学研究(英文版)》2020,(4)
This paper describes the establishment and verification of an accurate pointing model for a1.2 m aperture slant-axis terahertz antenna. A new analytical pointing model for the slant-axis antenna is presented based on an analogy to that of the alt-azimuth antennas. Furthermore, extra error terms are added to the pointing model based on the structure and mechanical analysis of the slant-axis antenna. To verify the pointing model experimentally, a pointing error measurement method based on photogrammetric techniques is proposed. Using this method, pointing behaviors of the antenna are accurately measured without the aid of astronomical observations, and major sources of the pointing errors are measured individually by photogrammetry and their respective coefficients are compared with those in the analytical pointing model.The results show that an extended pointing model consisting 21 error terms can significantly reduce the residual systematic errors compared with the traditional model, more details are given in the following sections. 相似文献