共查询到18条相似文献，搜索用时 296 毫秒
1.
为实现地震作用下锈蚀钢筋混凝土柱精细化数值模拟分析,基于已有研究成果建立往复荷载作用下锈蚀钢筋与混凝土间的黏结滑移本构模型:结合课题组前期试验结果,采用ABAQUS有限元分析软件对建立的黏结滑移本构模型进行有效性验证,通过对数值计算结果与试验结果之间误差分析,进一步对黏结滑移模型中的摩擦黏结应力系数和退化系数进行修正,最终建立更为合理的锈蚀钢筋与混凝土间黏结滑移本构模型。通过数值计算结果与试验结果的再次比较,验证修正后黏结滑移本构模型的有效性。结果表明:修正后的锈蚀钢筋与混凝土间黏结滑移模型可更好地反映往复荷载作用下锈蚀钢筋混凝土柱的滞回性能。该成果可为地震作用下锈蚀钢筋混凝土结构的数值分析计算提供理论参考。 相似文献
2.
3.
反复荷载下矩形钢管混凝土柱的抗震性能Ⅱ:分析研究 总被引：1，自引：0，他引：1
文中首先提出了钢管与内填混凝土界面的粘结-滑移滞回模型，建立了考虑包兴格效应的钢材单轴滞回模型和考虑矩形钢管约束效应后内填混凝土的单轴应力-应变滞回模型。在截面纤维模型的基础上，建立了考虑界面粘结-滑移的矩形钢管混凝土柱分析模型，用Fortran语言编制了相应的全过程分析程序。对作者等完成的试件进行了滞回全过程数值模拟计算，分析与试验结果在荷载-位移和荷载-应变两种层次上进行了对比。之后，利用该分析程序对矩形钢管混凝土柱中有代表性的混凝土和钢单元应力-应变发展全过程进行了跟踪分析。最后，以典型试件为对象，分析了钢-混凝土界面切向粘结强度对柱滞回性能的影响。本文工作可为从事组合结构研究时提供参考。 相似文献
4.
5.
研究了基于纤维模型的CFT框架柱滞回性能模拟的建模方法,建立了基于不同材料本构模型的CFT框架柱数值模型,并探讨了材料本构关系、纤维截面网格划分、积分点数量等因素对模拟精度的影响。以试验为依据,运用Opensees软件,通过计算结果与试验结果的对比,分析了影响滞回模型计算精度的主要因素。结果表明,受约束混凝土本构关系的下降段,钢材本构关系的强化段,是影响滞回模型准确性的主要因素,而网格划分和积分点数量的影响则主要体现在程序运行速率方面。研究将为基于纤维模型法的CFT框架柱滞回性能模拟分析提供理论依据。 相似文献
6.
柔度法纤维模型在方钢管混凝土柱滞回仿真中的应用 总被引：2，自引：0，他引：2
本文编制了基于二阶柔度法纤维模型梁柱单元的矩形钢管混凝土框架结构非线性分析程序,采用虚拟阶步法和改进的滞回路径追踪方法消除了其中截面切线刚度矩阵奇异时无法求逆的隐患,提高了算法的稳定性.运用此程序对矩形钢管混凝土柱进行滞回仿真,并与试验结果对比,结果表明:柔度法纤维模型梁柱单元可以有效解决框架结构的几何非线性问题和压弯耦合的材料非线性问题,使用较少的单元数量就可以得到较准确的计算结果;本文所采用的改进措施切实有效,保证了程序的稳定性. 相似文献
7.
8.
《世界地震工程》2016,(2)
试验研究及震害调查发现:由于配箍不足或箍筋间距过大,地震作用下钢筋混凝土柱易发生剪切破坏,继而发生轴向破坏。采用纤维截面的钢筋混凝土梁柱单元及与之串联的剪切弹簧以及轴向弹簧考虑钢筋混凝土柱的轴-弯-剪耦合效应,其中纤维梁柱单元用于模拟柱的弯曲机制,与梁柱单元串联的剪切弹簧和轴向弹簧用于模拟剪切机制和轴向机制,并利用单轴材料模型中的Limit State Material及其相应的Shear Limit Curve和Axial Limit Curve确定材料的剪切破坏与轴向破坏失效点,最终从单元层次上定义轴-弯-剪耦合效应。为验证该数值模型的合理性,选取不同破坏形式、轴向力与水平循环往复荷载共同作用下拟静力试验的钢筋混凝土柱,借助Open Sees分析软件模拟其滞回性能。模拟结果与试验结果的对比分析表明:考虑轴-弯-剪耦合的串联模型能较好地模拟钢筋混凝土柱的强度、刚度退化及捏拢效应等,且能够反映钢筋混凝土构件在复杂应力条件下的受力性能。 相似文献
9.
为讨论利用纤维梁柱单元进行钢筋混凝土桥墩地震反应分析的建模方法,分别以4个悬臂式单柱墩和1个双柱墩拟静力加载试验,以及1个悬臂式单柱墩的振动台试验结果为依据,基于OpenSees数值分析平台建立了桥墩的地震反应分析模型。通过改变单元数量,分析了基于力的纤维梁柱单元和基于位移的纤维梁柱单元对桥墩地震反应的模拟精度。结果表明:对悬臂式单柱墩的拟静力和振动台试验,可沿墩高仅建立1个基于力的纤维梁柱单元,并在墩底串联1个考虑纵筋塑性渗透和粘结滑移的转动弹簧单元,即可获得很好的模拟结果。当采用基于位移的纤维梁柱单元时,应沿墩高至少建立2个单元,且塑性铰区至少有1个,才能保证获得较高的模拟精度。对双柱墩拟静力试验,采用基于力的纤维梁柱单元建模,沿每个墩高建立2个单元即可;以基于位移的纤维梁柱单元建模,建议沿每个墩高建立3个单元,且其中2个单元布置在塑性铰区。当数值模型可对静力滞回曲线取得很好的模拟结果后,该模型一般可对动力作用下墩顶最大位移和墩底最大剪力进行较为准确的模拟,但对墩顶残余位移的模拟精度无法保证。 相似文献
10.
为克服利用OpenSEES进行预制拼装桥墩纤维模型分析时干接缝区域模拟困难的问题,提出一种由刚性单元、非线性梁柱单元、零长度单元配合ENT单压材料组成的干接缝单元。通过基于干接缝单元的纤维模型数值模拟结果与文献中的1:3.5缩尺桥墩拟静力试验结果对比发现:该干接缝单元不仅解决了墩身混凝土压溃带来的模型不收敛问题,而且考虑了墩身节段宽度对干接缝区域的影响,使预制拼装桥墩干接缝处的力学性能更接近实际的力学性能;数值模拟结果与试验结果吻合较好证明了该干接缝单元用于模拟预制拼装桥墩干接缝区域的可行性。在此基础上设置耗能钢筋、外包钢管和墩底橡胶支承垫层作为桥墩附加耗能装置,对预制拼装桥墩进行拟静力循环加载模拟,研究不同耗能装置对预制拼装桥墩的滞回能力、预应力筋内力、累积耗能、残余位移以及等效刚度等性能参数的影响。结果表明:设置耗能钢筋和外包钢管可以显著提高预制拼装桥墩的耗能能力、水平承载力和刚度,降低预应力损失;设置墩底橡胶支承垫层也能提高预制拼装桥墩的耗能能力,但会降低桥墩的水平承载力和刚度,应根据桥墩自身刚度谨慎选择橡胶垫层的刚度。 相似文献
11.
In this paper, a fiber beam-column element considering flexure–shear interaction and bond-slip effect is developed for cyclic analysis of reinforced concrete (RC) structures. The element is based on conventional displacement-based Timoshenko beam theory, where the transverse shear deformation is included, and adopts the fiber model to describe the section force–deformation behavior. In the fiber model, shear deformation is assumed to be uniformly distributed along the section and is only resisted by concrete, thus the multi-dimensional concrete damage model is used for concrete fibers and therefore flexure–shear interaction is reflected naturally at the material level. Meanwhile, to account for the significant bond-slip effect at critical regions, the anchorage slip of bars at these regions is analytically derived. Then it is used to modify the uniaxial stress–strain model for steel fibers by assuming that the total strain can be treated as the sum of the bar deformation and anchorage slip, therefore the bond-slip effect is implicitly but simply represented. To validate the proposed element, a series of RC member and structure tests under cyclic loading are simulated. The results indicate that the proposed element can predict cyclic responses of RC structures, and can be used as a reliable tool for analysis of RC structures. 相似文献
12.
钢筋锈蚀深度预测是评估在役RC结构服役性能的基础。为建立一般大气环境RC构件中钢筋锈蚀深度预测模型,通过收集实测数据,分析影响钢筋锈蚀深度的主要参数及其影响规律,继而基于实测数据建立数值模型和RBF神经网络预测模型,并进行参数敏感性分析。研究结果表明:与数值模型相比,RBF神经网络对钢筋锈蚀深度预测效率与精度更高,能够有效映射各影响参数与钢筋锈蚀深度之间复杂的非线性关系。参数敏感性分析结果显示,钢筋混凝土表面锈胀裂缝宽度对钢筋锈蚀深度影响最大,钢筋直径、保护层厚度与钢筋直径之比和混凝土抗压强度等其他因素影响次之。所得模型可用于工程检测中钢筋锈蚀程度预测与RC构筑物剩余服役寿命评估。 相似文献
13.
随着服役时间的增长，侵蚀环境下钢筋混凝土框架节点因钢筋发生不同程度的锈蚀而造成承载性能下降，严重影响建筑结构的安全使用。本文在已有钢筋混凝土框架节点抗剪强度理论模型的基础上，考虑钢筋锈蚀对框架节点受力性能的影响，建立锈蚀钢筋混凝土框架中节点受剪承载力计算公式。通过11组锈蚀钢筋混凝土节点试验数据，对建议理论模型进行验证。研究结果表明，锈蚀钢筋混凝土节点受剪承载力试验值与理论计算值之比的平均值为0.951，方差为0.075，二者吻合较好，本文建议的计算方法可用于锈蚀钢筋混凝土框架中节点承载力分析。 相似文献
14.
采用有限元软件ABAQUS,以锈蚀率（0%、5%、10%、15%和20%）为变量,对5根钢筋混凝土柱的力学性能进行了数值模拟,研究各试件的滞回性能、骨架曲线、延性及耗能能力,分析钢筋锈蚀率对承载力、延性、耗能和塑性铰转动能力的影响。研究结果表明:模拟分析得到的锈蚀钢筋混凝土柱的强度和变形与试验结果吻合较好,建立的有限元模型可用于锈蚀钢筋混凝土柱的力学性能分析;混凝土开裂前,锈蚀构件的力学性能基本与未锈蚀构件相同,混凝土开裂后,构件的承载力、屈服荷载、极限位移、延性等均随钢筋锈蚀率的增大而降低;轻度锈蚀构件的滞回性能和破坏形式与未锈蚀构件类似,随着钢筋锈蚀率逐渐增大,滞回环的饱满程度降低,“捏拢”现象严重,滞回曲线由“弓形”逐渐发展成“反S形”,耗能能力降低,破坏形式趋于脆性破坏,位移延性系数、平均耗能系数等指标逐渐下降。 相似文献
15.
In addition to the normal service loadings, engineering structures may be subjected to occasional loadings such as earthquakes, which may cause severe destruction. When the steel rebar is corroded, the damage could be more serious. To investigate the seismic performance of corroded RC columns, a three-dimensional mesoscale finite element model was established. In this approach, concrete was considered as a three-phase composite composed of aggregate, mortar matrix and interfacial transition zone (ITZ). The nonlinear spring were used to describe the bond slip between steel and concrete. The degradation of the material properties of the steel rebar and cover concrete as well as the bonding performance due to corrosion were taken into account. The rationality of the developed numerical analysis model was verified by the good agreement between the numerical results and the available experimental observation. On this basis, the effect of corrosion level, axial force ratio and shear-span ratio on the seismic performance of corroded RC columns, including lateral bearing capacity, ductility, and energy consumption, were explored and discussed. The simulation results indicate that the mesoscopic method can consider the heterogeneity of concrete, to more realistically and reasonably reflect the destruction process of structures.
相似文献16.
A uniaxial concrete constitutive model considering the bond-slip effect is proposed and its finite element analysis (FEA) implementation on a fiber section 相似文献
17.
A series of tests on three full-scale substandard exterior beam-column joints were performed to investigate the efficiency of the proposed retrofit configuration, which is the use of externally applied post-tensioned shape memory alloy (SMA) bars. A major group of structural deficiencies resulting from lack of shear reinforcement in the joint, use of low strength concrete and plain round bars were taken into account in the construction of test specimens. While the reference specimen represents the as-built subassembly, the other two were retrofitted by the post-tensioned SMA and steel bars to compare the contribution of superelastic and conventional material on the response. The specimens were exposed to quasi-static cyclic loading up to 8% drift ratio to simulate an intensive level of seismic hazard. The reference specimen underwent a brittle shear failure as excessive cracks mostly concentrated in the joint panel while there was almost no damage in the rest of the RC components. A joint failure with enhanced response quantities was observed in the specimen retrofitted by post-tensioned steel bars. The specimen incorporating the retrofit solution via post-tensioned SMA bars was capable of performing an adequate performance and promoting minimization of the damage in the joint panel, which results in more ductile behavior. The hysteretic response of the SMA retrofitted specimen was validated with a refined numerical model in ATENA Science software. Experimentally observed response was also verified by an analytical model based on fracture mechanics considering the nonlinear behavior of plain concrete under tension. Due to inherent uncertainties in material constitutive laws, the analytical model was evolved to a stochastic level to propose a more advanced model for estimating the capacity of the reference and retrofitted joint. It is found that the experimental results were within the prominent range of Probability Density Functions (i.e. mean ± 1 SD) of the estimated joint tensile stress especially for the shear damaged specimens. 相似文献
18.
预应力混凝土结构非线性地震反应分析 总被引：4，自引：0，他引：4
本文针对预应力混凝土与普通混凝土不同的受力特点,提出了适合于分析预应力混凝土结构抗震性能的非线性有限元模型。模型首先将混凝土结构离散为杆单元,然后对各杆单元按分层组合原理分成许多混凝土层、预应力钢筋层和普通钢筋层,计算混凝土分层单元、预应力钢筋和普通钢筋的应力和应变,最后,根据钢筋与混凝土之间的粘结－滑移关系高速钢筋变形,根据混凝土弹性模量调整结构及杆单元变形,通过对普通混凝土构件和三个预应力混凝 相似文献