首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
The influence of aqueous silica on the hydrolysis of iron(III) nitrate and chloride salts in dilute aqueous solutions (mFe ∼ 0.01 mol/kg) was studied at ambient temperature using X-ray absorption fine structure (XAFS) spectroscopy at the Fe K-edge. Results show that in Si-free iron nitrate and chloride solutions at acid pH (pH < 2.5), Fe is hexa-coordinated with 6 oxygens of H2O- and/or OH-groups in the first coordination sphere of the metal, at an Fe-O distance of 2.00 ± 0.01 Å. With increasing pH (2.7 < pH < 13), these groups are rapidly replaced by bridging hydroxyls (-OH-) or oxygens (-O-), and polymerized Fe hydroxide complexes form via Fe-(O/OH)-Fe bonds. In these polymers, the first atomic shell of iron represents a distorted octahedron with six O/OH groups and Fe-O distances ranging from 1.92 to 2.07 Å. The Fe octahedra are linked together by their edges (Fe-Fe distance 2.92-3.12 Å) and corners (Fe-Fe distance ∼3.47 ± 0.03 Å). The Fe-Fe coordination numbers (Nedge = 1-2; Ncorner = 0.5-0.7) are consistent with the dominant presence of iron dimers, trimers and tetramers at pH 2.5 to 2.9, and of higher-polymerized species at pH > 3.At pH > 2.5 in the presence of aqueous silica, important changes in Fe(III) hydrolysis are detected. In 0.05-m Si solutions (pH ∼ 2.7-3.0), the corner linkages between Fe octahedra in the polymeric complexes disappear, and the Fe-Fe distances corresponding to the edge linkages slightly increase (Fe-Feedge ∼ 3.12-3.14 Å). The presence of 1 to 2 silicons at 3.18 ± 0.03 Å is detected in the second atomic shell around iron. At basic pH (∼12.7), similar structural changes are observed for the iron second shell. The Fe-Si and Fe-Fe distances and coordination numbers derived in this study are consistent with (1) Fe-Si complex stoichiometries Fe2Si1-2 and Fe3Si2-3 at pH < 3; (2) structures composed of Fe-Fe dimers and trimers sharing one or two edges of FeO6-octahedra; and (3) silicon tetrahedra linked to two neighboring Fe octahedra via corners. At higher Si concentration (0.16 m, polymerized silica solution) and pH ∼ 3, the signal of the Fe second shell vanishes indicating the destruction of the Fe-Fe bonds and the formation of different Fe-Si linkages. Moreover, ∼20 mol.% of Fe is found to be tetrahedrally coordinated with oxygens in the first coordination shell (RFe-O = 1.84 Å). This new finding implies that Fe may partially substitute for Si in the tetrahedral network of the silica polymers in Si-rich solutions.The results of this study demonstrate that aqueous silica can significantly inhibit iron polymerization and solid-phase formation, and thus increase the stability and mobility of Fe(III) in natural waters. The silica “poisoning” of the free corner sites of iron-hydroxide colloids should reduce the adsorption and incorporation of trace elements by these colloids in Si-rich natural waters.  相似文献   

2.
Stability and solubility of arsenopyrite, FeAsS, in crustal fluids   总被引：3，自引：0，他引：3  
The stability and solubility of natural arsenopyrite (FeAsS) in pure water and moderately acid to slightly basic aqueous solutions buffered or not with H2 and/or H2S were studied at temperatures from 300 to 450°C and pressures from 100 to 1000 bar. The solubilities of FeAsS in pure water and dilute HCl/NaOH solutions without buffering are consistent with the formation of the As(OH)30(aq) species and precipitation of magnetite. At more acid pH (pH ≤2), arsenopyrite dissolves either stoichiometrically or with formation of the As-FeAsS assemblage. In H2S-rich and H2-rich aqueous solutions, arsenopyrite dissolution results in the formation of pyrrhotite (±pyrite) and iron arsenide(s), respectively, which form stable assemblages with arsenopyrite.Arsenic concentrations measured in equilibrium with FeAsS in slightly acid to neutral aqueous solutions with H2 and H2S fugacities buffered by the pyrite-pyrrhotite-magnetite assemblage are 0.0006 ± 0.0002, 0.0055 ± 0.0010, 0.07 ± 0.01, and 0.32 ± 0.03 mol/kg H2O at 300°C/400 bar, 350°C/500 bar, 400°C/500 bar, and 450°C/500 bar, respectively. These values were combined with the available thermodynamic data on As(OH)30(aq) (Pokrovski et al., 1996) to derive the Gibbs free energy of FeAsS at each corresponding temperature and pressure. Extrapolation of these values to 25°C and 1 bar, using the available heat capacity and entropy data for FeAsS (Pashinkin et al., 1989), yields a value of −141.6 ± 6.0 kJ/mol for the standard Gibbs free energy of formation of arsenopyrite. This value implies a higher stability of FeAsS in hydrothermal environments than was widely assumed.Calculations carried out using the new thermodynamic properties of FeAsS demonstrate that this mineral controls As transport and deposition by high-temperature (>∼300°C) crustal fluids during the formation of magmatic-hydrothermal Sn-W-Cu-(Au) deposits. The equilibrium between As-bearing pyrite and the fluid is likely to account for the As concentrations measured in modern high- and moderate-temperature (150 ≤ T ≤ 350°C) hydrothermal systems. Calculations indicate that the local dissolution of arsenopyrite creates more reducing conditions than in the bulk fluid, which is likely to be an effective mechanism for precipitating gold from hydrothermal solutions. This could be a possible explanation for the gold-arsenopyrite association commonly observed in many hydrothermal gold deposits.  相似文献   

3.
The solubility of silver sulphide (acanthite/argentite) has been measured in aqueous sulphide solutions between 25 and 400°C at saturated water vapour pressure and 500 bar to determine the stability and stoichiometry of sulphide complexes of silver(I) in hydrothermal solutions. The experiments were carried out in a flow-through autoclave, connected to a high-performance liquid chromatographic pump, titanium sampling loop, and a back-pressure regulator on line. Samples for silver determination were collected via the titanium sampling loop at experimental temperatures and pressures. The solubilities, measured as total dissolved silver, were in the range 1.0 × 10−7 to 1.30 × 10−4 mol kg−1 (0.01 to 14.0 ppm), in solutions of total reduced sulphur between 0.007 and 0.176 mol kg−1 and pHT,p of 3.7 to 12.7. A nonlinear least squares treatment of the data demonstrates that the solubility of silver sulphide in aqueous sulphide solutions of acidic to alkaline pH is accurately described by the reactions0.5Ag2S(s) + 0.5H2S(aq) = AgHS(aq) Ks,1110.5Ag2S(s) + 0.5H2S(aq) + HS− = Ag(HS)2− Ks,122Ag2S(s) + 2HS− = Ag2S(HS)22− Ks,232where AgHS(aq) is the dominant species in acidic solutions, Ag(HS)2− under neutral pH conditions and Ag2S(HS)22− in alkaline solutions. With increasing temperature the stability field of Ag(HS)2− increases and shifts to more alkaline pH in accordance with the change in the first ionisation constant of H2S(aq). Consequently, Ag2S(HS)22− is not an important species above 200°C. The solubility constant for the first reaction is independent of temperature to 300°C, with values in the range logKs,111 = −5.79 (±0.07) to −5.59 (±0.09), and decreases to −5.92 (±0.16) at 400°C. The solubility constant for the second reaction increases almost linearly with inverse temperature from logKs,122 = −3.97 (±0.04) at 25°C to −1.89 (±0.03) at 400°C. The solubility constant for the third reaction increases with temperature from logKs,232 = −4.78 (±0.04) at 25°C to −4.57 (±0.18) at 200°C. All solubility constants were found to be independent of pressure within experimental uncertainties. The interaction between Ag+ and HS− at 25°C and 1 bar to form AgHS(aq) has appreciable covalent character, as reflected in the exothermic enthalpy and small entropy of formation. With increasing temperature, the stepwise formation reactions become progressively more endothermic and are accompanied by large positive entropies, indicating greater electrostatic interaction. The aqueous speciation of silver is very sensitive to fluid composition and temperature. Below 100°C silver(I) sulphide complexes predominate in reduced sulphide solutions, whereas Ag+ and AgClOH− are the dominant species in oxidised waters. In high-temperature hydrothermal solutions of seawater salinity, chloride complexes of silver(I) are most important, whereas in dilute hydrothermal fluids of meteoric origin typically found in active geothermal systems, sulphide complexes predominate. Adiabatic boiling of dilute and saline geothermal waters leads to precipitation of silver sulphide and removal of silver from solution. Conductive cooling has insignificant effects on silver mobility in dilute fluids, whereas it leads to quantitative loss of silver for geothermal fluids of seawater salinity.  相似文献   

4.
Detrital zircon grains from Beit Bridge Group quartzite from the Central Zone of the Limpopo Belt near Musina yield mostly ages of 3.35-3.15 Ga, minor 3.15-2.51 Ga components, and numerous older grains grouped at approximately 3.4, 3.5 and 3.6 Ga. Two grains yielded concordant Late Hadean U-Pb ages of 3881 ± 11 Ma and 3909 ± 26 Ma, which are the oldest zircon grains so far found in Africa. The combined U-Pb and Lu-Hf datasets and field relationships provide evidence that the sedimentary protolith of the Beit Bridge Group quartzite was deposited after the emplacement of the Sand River Gneisses (3.35-3.15 Ga), but prior to the Neoarchean magmatic-metamorphic events at 2.65-2.60 Ga. The finding of abundant magmatic zircon detritus with concordant U-Pb ages of 3.35-3.15 Ga, and 176Hf/177Hf of 0.28066 ± 0.00004 indicate that the Sand River Gneiss-type rocks were a predominant source. In contrast, detrital zircon grains older than approximately 3.35 Ga were derived from the hinterland of the Limpopo Belt; either from a so far unknown crustal source in southern Africa, possibly from the Zimbabwe Craton and/or a source, which was similar but not necessarily identical to the one that supplied the Hadean zircons to Jack Hills, Western Australia. The Beit Bridge Group zircon population at >3.35 Ga shows a general εHft increase with decreasing age from εHf3.9Ga = −6.3 to εHf3.3-3.1Ga = −0.2, indicating that Hadean crust older than 4.0 Ga (TDM = 4.45-4.36 Ga) was rejuvenated during magmatic events between >3.9 and 3.1 Ga, due to a successive mixing of crustal rocks with mantle derived magmas. The existence of a depleted mantle reservoir in the Limpopo’s hinterland is reflected by the ∼3.6 Ga zircon population, which shows εHf3.6Ga between −4.6 and +3.2. In a global context, our data suggest that a long-lived, mafic Hadean protocrust with some tonalite-trondhjemite-granodiorite constituents was destroyed and partly recycled at the Hadean/Archean transition, perhaps due to the onset of modern-style plate tectonics.  相似文献   

5.
The solubility of gold has been measured in aqueous solutions at temperatures between 300 and 600°C and pressures from 500 to 1500 bar to determine the stability and stoichiometry of the hydroxy complexes of gold(I) in hydrothermal solutions. The experiments were carried out using a flow-through autoclave system. The solubilities, measured as total dissolved gold, were in the range 1.2 × 10−8 to 2.0 × 10−6 mol kg−1 (0.002 to 0.40 mg kg−1), in solutions of total dissolved sodium between 0.0 and 0.5 mol kg−1, and total dissolved hydrogen between 4.0 × 10−6 and 4.0 × 10−4 mol kg−1. At constant hydrogen molality, the solubility of gold increases with increasing temperature and decreases with increasing pressure. The solubilities were found to be independent of pH but increased with decreasing hydrogen molality at constant temperature and pressure. Consequently, gold dissolves in aqueous solutions of acidic to alkaline pH according to the reactionAu(s)+H2O(l)=AuOH(aq)+0.5H2(g) Ks,1The solubility constant, logKs,1, increases with increasing temperature from a minimum of −8.76 (±0.18) at 300°C and 500 bar to a maximum of −7.50 (±0.11) at 500°C and 1500 bar and decreases to −7.61 (±0.08) at 600°C and 1500 bar. From the equilibrium solubility constant and the redox potential of gold, the formation constant to form AuOH(aq) was calculated. At 25°C the complex formation is characterised by an exothermic enthalpy and a positive entropy. With increasing temperature and decreasing pressure, the formation reaction becomes endothermic and is accompanied by a large positive entropy, indicating a greater electrostatic interaction between Au+ and OH−.  相似文献   

6.
Formation of aqueous aluminate-borate complexes was characterized at 25°C using 27Al NMR spectroscopy, and at 50-200°C via measurements of gibbsite and boehmite solubility in the presence of boric acid. 27Al spectra performed at pH = 9 in Al-B solution with m(B) = 0.02 show the presence of two peaks at 80.5 and 74.5 ppm which correspond to Al(OH)4− and a single Al-substituted Q1Al dimer, Al(OH)3OB(OH)2−, respectively. In 0.08 m and 0.2 m borate solution, a third peak appears at 68.5 ppm which can be assigned to the Q2Al trimer Al(OH)2O2(B(OH)2)2−. These chemical shifts are close to those measured for Al(OH)3OSi(OH)3− and Al(OH)2O2(Si(OH)3)2− (74 and 69.5 ppm, respectively; Pokrovski et al., Min. Mag.62a (1998), 1194) which demonstrates the similar structure of Al-B and Al-Si complexes formed in alkaline solutions. Gibbsite and boehmite solubility were measured in weakly basic solutions as a function of boric acid concentration at 50°C and 78 to 200°C, respectively. Equilibrium was reached within several days at m(B) = 0.01-0.1, but more slowly at higher boron concentrations, and at 50°C and m(B) = 0.2, Al concentration increased continuously during at least 3 months as a result of the sluggish formation of Al-polyborates. The equilibrium constant of the reaction Al(OH)4− + B(OH)30(aq) = Al(OH)3OB(OH)2− + H2O decreases very slowly with increasing temperature to 200°C. The log K values are 1.58 ± 0.10, 1.46 ± 0.10, 1.52 ± 0.15, and 1.25 ± 0.15 at 50, 78, 150 and 200°C, respectively, which result in the following values of the standard thermodynamic properties for this reaction: ΔrG0 = −9.22 ± 3.25 kJ/mol, ΔrH0 = −4.6 ± 2.5 kJ/mol, ΔrS0 = 15.5 ± 6.9 J/mol K. The thermodynamic data generated in this study indicate that Al-B complexes can dominate aqueous aluminum speciation in solutions containing ≥0.7 g/L of boron at temperature to at least 400°C.  相似文献   

7.
The mobility and transport of gold in low-temperature waters and brines is affected by the aqueous speciation of gold, which is sensitive in particular to pH, oxidation and halide concentrations. In this study, we use UV-Vis spectrophotometry to identify and measure the thermodynamic properties of Au(III) aqueous complexes with chloride, bromide and hydroxide. Au(III) forms stable square planar complexes with hydroxide and halide ligands. Based on systematic changes in the absorption spectra of solutions in three binary systems NaCl-NaBr, NaCl-NaOH and NaBr-NaOH at 25 °C, we derived log dissociation constants for the following mixed and end-member halide and hydroxide complexes: [AuCl3Br]−, [AuCl2Br2]−, [AuBr3Cl]− and [AuBr4]−; [AuCl3(OH)]−, [AuCl2(OH)2]−, [AuCl(OH)3]− and [Au(OH)4]−; and [AuBr3(OH)]−, [AuBr2(OH)2]− and [AuBr(OH)3]−. These are the first reported results for the mixed chloride-bromide complexes. Increasing temperature to 80 °C resulted in an increase in the stability of the mixed chloride-bromide complexes, relative to the end-member chloride and bromide complexes. For the [AuCl(4−n)(OH)n]− series of complexes (n = 0-4), there is an excellent agreement between our spectrophotometric results and previous electrochemical results of Chateau et al. [Chateau et al. (1966)]. In other experiments, the iodide ion (I−) was found to be unstable in the presence of Au(III), oxidizing rapidly to I2(g) and causing Au to precipitate. Predicted Au(III) speciation indicates that Au(III) chloride-bromide complexes can be important in transporting gold in brines with high bromide-chloride ratios (e.g., >0.05), under oxidizing (atmospheric), acidic (pH < 5) conditions. Native gold solubility under atmospheric oxygen conditions is predicted to increase with decreasing pH in acidic conditions, increasing pH in alkaline conditions, increasing chloride, especially at acid pH, and increasing bromide for bromide/chloride ratios greater than 0.05. The results of our study increase the understanding of gold aqueous geochemistry, with the potential to lead to new methods for mineral exploration, hydrometallurgy and medicine.  相似文献   

8.
Although iron isotopes provide a new powerful tool for tracing a variety of geochemical processes, the unambiguous interpretation of iron isotope ratios in natural systems and the development of predictive theoretical models require accurate data on equilibrium isotope fractionation between fluids and minerals. We investigated Fe isotope fractionation between hematite (Fe2O3) and aqueous acidic NaCl fluids via hematite dissolution and precipitation experiments at temperatures from 200 to 450 °C and pressures from saturated vapor pressure (Psat) to 600 bar. Precipitation experiments at 200 °C and Psat from aqueous solution, in which Fe aqueous speciation is dominated by ferric iron (FeIII) chloride complexes, show no detectable Fe isotope fractionation between hematite and fluid, Δ57Fefluid-hematite = δ57Fefluid − δ57Fehematite = 0.01 ± 0.08‰ (2 × standard error, 2SE). In contrast, experiments at 300 °C and Psat, where ferrous iron chloride species (FeCl2 and FeCl+) dominate in the fluid, yield significant fluid enrichment in the light isotope, with identical values of Δ57Fefluid-hematite = −0.54 ± 0.15‰ (2SE) both for dissolution and precipitation runs. Hematite dissolution experiments at 450 °C and 600 bar, in which Fe speciation is also dominated by ferrous chloride species, yield Δ57Fefluid-hematite values close to zero within errors, 0.15 ± 0.17‰ (2SE). In most experiments, chemical, redox, and isotopic equilibrium was attained, as shown by constancy over time of total dissolved Fe concentrations, aqueous FeII and FeIII fractions, and Fe isotope ratios in solution, and identical Δ57Fe values from dissolution and precipitation runs. Our measured equilibrium Δ57Fefluid-hematite values at different temperatures, fluid compositions and iron redox state are within the range of fractionations in the system fluid-hematite estimated using reported theoretical β-factors for hematite and aqueous Fe species and the distribution of Fe aqueous complexes in solution. These theoretical predictions are however affected by large discrepancies among different studies, typically ±1‰ for the Δ57Fe Fe(aq)-hematite value at 200 °C. Our data may thus help to refine theoretical models for β-factors of aqueous iron species. This study provides the first experimental calibration of Fe isotope fractionation in the system hematite-saline aqueous fluid at elevated temperatures; it demonstrates the importance of redox control on Fe isotope fractionation at hydrothermal conditions.  相似文献   

9.
The interaction of aqueous As(III) with magnetite during its precipitation from aqueous solution at neutral pH has been studied as a function of initial As/Fe ratio. Arsenite is sequestered via surface adsorption and surface precipitation reactions, which in turn influence the crystal growth of magnetite. Sorption samples were characterized using EXAFS spectroscopy at the As K-edge in combination with HRTEM observations, energy dispersive X-ray analysis at the nanoscale, electron energy loss spectroscopy at the Fe L3-edge, and XRD-Rietveld analyses of reaction products. Our results show that As(III) forms predominantly tridentate hexanuclear As(III)O3 complexes (3C), where the As(III)O3 pyramids occupy vacant tetrahedral sites on {1 1 1} surfaces of magnetite particles. This is the first time such a tridentate surface complex has been observed for arsenic. This complex, with a dominant As-Fe distance of 3.53 ± 0.02 Å, occurs in all samples examined except the one with the highest As/Fe ratio (0.33). In addition, at the two highest As/Fe ratios (0.133 and 0.333) arsenite tends to form mononuclear edge-sharing As(III)O3 species (2E) within a highly soluble amorphous As(III)-Fe(III,II)-containing precipitate. At the two lowest As/Fe ratios (0.007 and 0.033), our results indicate the presence of additional As(III) species with a dominant As-Fe distance of 3.30 ± 0.02 Å, for which a possible structural model is proposed. The tridentate 3C As(III)O3 complexes on the {1 1 1} magnetite surface, together with this additional As(III) species, dramatically lower the solubility of arsenite in the anoxic model systems studied. They may thus play an important role in lowering arsenite solubility in putative magnetite-based water treatment processes, as well as in natural iron-rich anoxic media, especially during the reductive dissolution-precipitation of iron minerals in anoxic environments.  相似文献   

10.
The types and structures of adsorption complexes formed by oxalate at boehmite (γ-AlOOH)/water and corundum (α-Al2O3)/water interfaces were determined using in situ attenuated total reflectance fourier transform infrared (ATR-FTIR) spectroscopy and quantum chemical simulation methods. At pH 5.1, at least four different oxalate species were found at or near the boehmite/water interface for oxalate surface coverages (Γox) ranging from 0.25 to 16.44 μmol/m2. At relatively low coverages (Γox < 2.47), strongly adsorbed inner-sphere oxalate species (IR peaks at 1286, 1418, 1700, and 1720 cm−1) replace weakly adsorbed carbonate species, and a small proportion of oxalate anions are adsorbed in an outer-sphere mode (IR peaks at 1314 and 1591 cm−1). IR peaks indicative of inner-sphere adsorbed oxalate are also observed for oxalate at the corundum/water interface at Γox = 1.4 μmol/m2. With increasing oxalate concentration (Γox > 2.47 μmol/m2), the boehmite surface binding sites for inner-sphere adsorbed oxalate become saturated, and excess oxalate ions are present dominantly as aqueous species (IR peaks at 1309 and 1571 cm−1). In addition to these adsorption processes, oxalate-promoted dissolution of boehmite following inner-sphere oxalate adsorption becomes increasingly pronounced with increasing Γox and results in an aqueous Al(III)-oxalate species, as indicated by shifted IR peaks (1286 → 1297 cm−1 and 1418 → 1408 cm−1). At pH 2.5, no outer-sphere adsorbed oxalate or aqueous oxalate species were observed. The similarity of adsorbed oxalate spectral features at pH 2.5 and 5.1 implies that the adsorption mechanism of aqueous HOx− species involves loss of protons from this species during the ligand-exchange reaction. As a consequence, adsorbed inner-sphere oxalate and aqueous Al(III)-oxalate complexes formed at pH 2.5 have coordination geometries very similar to those formed at pH 5.1.The coordination geometry of inner-sphere adsorbed oxalate species was also predicted using quantum chemical geometry optimization and IR vibrational frequency calculations. Geometry-optimized Al8O12 and Al14O22 clusters with the reactive surface Al site coordinated by three oxygens were used as model substrates for corundum and boehmite surfaces. Among the models considered, calculated IR frequencies based on a bidentate side-on structure with a 5-membered ring agree best with the observed frequencies for boehmite/oxalate/water samples at Γox = 0.25 to 16.44 μmol/m2 and pH 2.5 and 5.1, and for a corundum/oxalate/water sample at Γox = 1.4 μmol/m2 and pH 5.1. Based on these results, we suggest that oxalate bonding on boehmite and corundum surfaces results in 5-coordinated rather than 4- or 6-coordinated Al surface sites.  相似文献   

11.
The AlOx1-3 (Ox = oxalate) species were identified in 0.6 M aqueous NaCl by 13C nuclear magnetic resonance (NMR). Rate constants and activation parameters for intramolecular cis/trans isomerization of the Werner-type AlOx2− complex (k(298 K) = 5 s−1, ΔH# = 67 ± 5 kJ mol−1, ΔS# = −6 ± 6 J mol−1 K−1, the rate determining step could be the breaking of the Al-O(C=O) bond) and a very slow intermolecular ligand exchange reaction of AlOx33− complex and the free ligand (k30(298 K) = 6.6 · 10−5 s−1, ΔH# = 164 ± 17 kJ mol−1, ΔS# = 225 ± 51 J mol−1 K−1, D/Id mechanism) were determined by dynamic 1D and 2D 13C NMR measurements. Mixed complexes, AlFOx, AlFOx22-, AlF2Ox−, and AlF2Ox23-, with overall stability (logβ) of 11.53 ± 0.03, 15.67 ± 0.03, 15.74 ± 0.02, and 19.10 ± 0.04 were measured by potentiometry using pH- and fluoride-selective electrodes and confirmed by 13C and19F NMR. The role of these complexes in gibbsite dissolution was modeled. The mixed Al(III)-Ox2--F− complexes have to be considered as the chemical speciation of Al(III) in natural waters is discussed.  相似文献   

12.
We investigate the sensitivity of U/Ca, Mg/Ca, and Sr/Ca to changes in seawater [CO32−] and temperature in calcite produced by the two planktonic foraminifera species, Orbulina universa and Globigerina bulloides, in laboratory culture experiments. Our results demonstrate that at constant temperature, U/Ca in O. universa decreases by 25 ± 7% per 100 μmol [CO32−] kg−1, as seawater [CO32−] increases from 110 to 470 μmol kg−1. Results from G. bulloides suggest a similar relationship, but U/Ca is consistently offset by ∼+40% at the same environmental [CO32−]. In O. universa, U/Ca is insensitive to temperature between 15°C and 25°C. Applying the O. universa relationship to three U/Ca records from a related species, Globigerinoides sacculifer, we estimate that Caribbean and tropical Atlantic [CO32−] was 110 ± 70 μmol kg−1 and 80 ± 40 μmol kg−1 higher, respectively, during the last glacial period relative to the Holocene. This result is consistent with estimates of the glacial-interglacial change in surface water [CO32−] based on both modeling and on boron isotope pH estimates. In settings where the addition of U by diagenetic processes is not a factor, down-core records of foraminiferal U/Ca have potential to provide information about changes in the ocean’s carbonate concentration.Below ambient pH (pH < 8.2), Mg/Ca decreased by 7 ± 5% (O. universa) to 16 ± 6% (G. bulloides) per 0.1 unit increase in pH. Above ambient pH, the change in Mg/Ca was not significant for either species. This result suggests that Mg/Ca-based paleotemperature estimates for the Quaternary, during which surface-ocean pH has been at or above modern levels, have not been biased by variations in surface-water pH. Sr/Ca increased linearly by 1.6 ± 0.4% per 0.1 unit increase in pH. Shell Mg/Ca increased exponentially with temperature in O. universa, where Mg/Ca = 0.85 exp (0.096*T), whereas the change in Sr/Ca with temperature was within the reproducibility of replicate measurements.  相似文献   

13.
The solubility of neodymium (III) fluoride was investigated at temperatures of 150, 200 and 250 °C, saturated water vapor pressure, and a total fluoride concentration (HF°aq + F−) ranging from 2.0 × 10−3 to 0.23 mol/l. The results of the experiments show that Nd3+ and NdF2+ are the dominant species in solution at the temperatures investigated and were used to derive formation constants for NdF2+ and a solubility product for NdF3. The solubility product of NdF3(logKsp=logaNd3++3logaF-) is −24.4 ± 0.2, −22.8 ± 0.1, and −21.5 ± 0.2 at 250, 200 and 150 °C, respectively, and the formation constant of NdF2+(logβ=logaNdF2+-logaNd3+-logaF-) is 6.8 ± 0.1, 6.2 ± 0.1, and 5.5 ± 0.2 at 250, 200 and 150 °C, respectively. The results of this study show that published theoretical predictions significantly overestimate the stability of NdF2+ and the solubility of NdF3.The potential impact of the results on natural systems was evaluated for a hypothetical fluid with a composition similar to that responsible for REE mineralization in the Capitan pluton, New Mexico. In contrast to results obtained using the theoretical predictions of Haas [Haas J. R., Shock E. L., and Sassani D. C. (1995) Rare earth elements in hydrothermal systems: estimates of standard partial molal thermodynamic properties of aqueous complexes of the rare earth elements at high pressures and temperatures. Geochim. Cosmochim. Acta59, 4329-4350.], which indicate that NdF2+ is the dominant species in solution, calculations employing the data presented in this paper and previously published experimental data for chloride and sulfate species [Migdisov A. A., and Williams-Jones A. E. (2002) A spectrophotometric study of neodymium(III) complexation in chloride solutions. Geochim. Cosmochim. Acta66, 4311-4323; Migdisov A. A., Reukov V. V., and Williams-Jones A. E. (2006) A spectrophotometric study of neodymium(III) complexation in sulfate solutions at elevated temperatures. Geochim. Cosmochim. Acta70, 983-992.] show that neodymium chloride species predominate and that neodymium fluoride species are relatively unimportant. This suggests that accepted models for REE deposits that invoke fluoride complexation as the method of hydrothermal REE transport may need to be re-evaluated.  相似文献   

14.
The adsorption of hydrogen sulfide (ΓH2S) and protons (ΓH+) on the surface of crystalline sulfur was investigated experimentally in H2S-bearing solutions at temperatures of 25, 50, and 70°C, NaCl concentrations of 0.1 and 0.5 mol/dm−3 and log CH+ values in the range −2.3 to −5. At all temperatures, the dominant process on the surface of the sulfur was deprotonation, and the average values of ΓH2S were very close to the highest values determined for ΓH+. This finding, combined with the lack of detectable proton adsorption in H2S-free solutions, suggests that proton adsorption/desorption on the surface of sulfur occurs through formation of ≡ S − H2S complexes in the presence of H2S.We propose that this complexation represents sulfidation of the sulfur surface, a process analogous to hydroxylation of oxide surfaces, and that the sulfidation can be described by the reaction: ≡ S + H2S = ≡SSH20 β° The deprotonation of the ≡ SH° complex occurs via the reaction: ≡ SSH20 = ≡SSH− + H+ β− Values of 2.9, 2.8, and 2.9 (± 0.23) were obtained for −log β− at 25, 50, and 70°C, respectively. These data were employed to estimate the second dissociation constant for hydrogen sulfide in aqueous solutions using the extrapolation method proposed by Schoonen and Barnes (1988) and yielded corresponding values for the constant of 17.4 ± 0.3, 15.7, and 14.5, respectively. The value for 25°C is in very good agreement with the experimentally determined values of Giggenbach (1971) at 17 ± 0.1; Meyer et al. (1983) at 17 ± 1; Licht and Manassen (1987) at 17.6 ± 0.3; and Licht et al. (1990) at 17.1 ± 0.3.  相似文献   

15.
Published solubility data for amorphous ferric arsenate and scorodite have been reevaluated using the geochemical code PHREEQC with a modified thermodynamic database for the arsenic species. Solubility product calculations have emphasized measurements obtained under conditions of congruent dissolution of ferric arsenate (pH < 3), and have taken into account ion activity coefficients, and ferric hydroxide, ferric sulfate, and ferric arsenate complexes which have association constants of 104.04 (FeH2AsO42+), 109.86 (FeHAsO4+), and 1018.9 (FeAsO4). Derived solubility products of amorphous ferric arsenate and crystalline scorodite (as log Ksp) are −23.0 ± 0.3 and −25.83 ± 0.07, respectively, at 25 °C and 1 bar pressure. In an application of the solubility results, acid raffinate solutions (molar Fe/As = 3.6) from the JEB uranium mill at McClean Lake in northern Saskatchewan were neutralized with lime to pH 2-8. Poorly crystalline scorodite precipitated below pH 3, removing perhaps 98% of the As(V) from solution, with ferric oxyhydroxide (FO) phases precipitated starting between pH 2 and 3. Between pH 2.18 and 7.37, the apparent log Ksp of ferric arsenate decreased from −22.80 to −24.67, while that of FO (as Fe(OH)3) increased from −39.49 to −33.5. Adsorption of As(V) by FO can also explain the decrease in the small amounts of As(V)(aq) that remain in solution above pH 2-3. The same general As(V) behavior is observed in the pore waters of neutralized tailings buried for 5 yr at depths of up to 32 m in the JEB tailings management facility (TMF), where arsenic in the pore water decreases to 1-2 mg/L with increasing age and depth. In the TMF, average apparent log Ksp values for ferric arsenate and ferric hydroxide are −25.74 ± 0.88 and −37.03 ± 0.58, respectively. In the laboratory tests and in the TMF, the increasing crystallinity of scorodite and the amorphous character of the coexisting FO phase increases the stability field of scorodite relative to that of the FO to near-neutral pH values. The kinetic inability of amorphous FO to crystallize probably results from the presence of high concentrations of sulfate and arsenate.  相似文献   

16.
The speciation of carbonate adsorbed to hematite in air-equilibrated aqueous solutions has been studied using ATR-FTIR spectroscopy. Samples were measured over a range of pH conditions, at 0.1 M NaCl and at low ionic strength, and in H2O and D2O solutions to permit a multispecies analysis of the data. Second-derivative analyses and fits to the spectra indicate the presence of two major and two minor surface-bound carbonate species. The two major complexes coexist at near-neutral pH and low ionic strength. One of these two complexes is relatively sensitive to ionic strength, being displaced at 0.1 M NaCl, whereas the other is not. Comparison of experimental to DFT/MO-calculated frequencies suggest these two major species to be (a) a monodentate binuclear inner-sphere carbonate surface complex, and (b) a fully or partially solvated carbonate (CO32−) species that is symmetry broken and appears to reside in the structured vicinal water layers at the hematite-water interface, retained by hydrogen bonding and/or other forces. Minor carbonate complexes include diffuse layer CO32− and an unidentified inner-sphere species. Both of the dominant species observed here are likely to be significant controls of the surface charge and sorptive properties of Fe-oxides.  相似文献   

17.
Four different sets of experiments were completed in order to constrain vivianite [Fe3(PO4)2 · 8H2O] reactivity under conditions pertinent to As(V)-bearing groundwater systems. Firstly, titration experiments were undertaken in the pH range 4-9 to determine the zero point of charge (ZPC) of vivianite; showing that the ZPC lies at a pH of approximately 5.3. Secondly, the steady state dissolution rates of vivianite far from equilibrium were measured in aqueous solutions in the pH range 2–10 at 18.5 °C (±3 °C) using a fluidized bed reactor. The rate of vivianite dissolution, R, is given by  相似文献   

18.
The stoichiometry and stability of arsenic gaseous complexes were determined in the system As-H2O ± NaCl ± HCl ± H2S at temperatures up to 500°C and pressures up to 600 bar, from both measurements of As(III) and As(V) vapor-liquid and vapor-solid partitioning, and X-ray absorption fine structure (XAFS) spectroscopic study of As(III)-bearing aqueous fluids. Vapor-aqueous solution partitioning for As(III) was measured from 250 to 450°C at the saturated vapor pressure of the system (Psat) with a special titanium reactor that allows in situ sampling of the vapor phase. The values of partition coefficients for arsenious acid (H3AsO3) between an aqueous solution (pure H2O) and its saturated vapor (K = mAsvapor /mAsliquid) were found to be independent of As(III) solution concentrations (up to ∼1 to 2 mol As/kg) and equal to 0.012 ± 0.003, 0.063 ± 0.023, and 0.145 ± 0.020 at 250, 300, and 350°C, respectively. These results are interpreted by the formation, in the vapor phase, of As(OH)3(gas), similar to the aqueous As hydroxide complex dominant in the liquid phase. Arsenic chloride or sulfide gaseous complexes were found to be negligible in the presence of HCl or H2S (up to ∼0.5 mol/kg of vapor). XAFS spectroscopic measurements carried out on As(III)-H2O (±NaCl) solutions up to 500°C demonstrate that the As(OH)3 complex dominates As speciation both in dense H2O-NaCl fluids and low-density supercritical vapor. Vapor-liquid partition coefficients for As(III) measured in the H2O-NaCl system up to 450°C are consistent with the As speciation derived from these spectroscopic measurements and can be described by a simple relationship as a function of the vapor-to-liquid density ratio and temperature. Arsenic(III) partitioning between vapor and As-concentrated solutions (>2 mol As/kg) or As2O3 solid is consistent with the formation, in the vapor phase, of both As4O6 and As(OH)3. Arsenic(V) (arsenic acid, H3AsO4) vapor-liquid partitioning at 350°C for dilute aqueous solution was interpreted by the formation of AsO(OH)3 in the vapor phase.The results obtained were combined with the corresponding properties for the aqueous As(III) hydroxide species to generate As(OH)3(gas) thermodynamic parameters. Equilibrium calculations carried out by using these data indicate that As(OH)3(gas) is by far the most dominant As complex in both volcanic gases and boiling hydrothermal systems. This species is likely to be responsible for the preferential partition of arsenic into the vapor phase as observed in fluid inclusions from high-temperature (400 to 700°C) Au-Cu (-Sn, -W) magmatic-hydrothermal ore deposits. The results of this study imply that hydrolysis and hydration could be also important for other metals and metalloids in the H2O-vapor phase. These processes should be taken into account to accurately model element fractionation and chemical equilibria during magma degassing and fluid boiling.  相似文献   

19.
Atomic force microscopy (AFM) was used to study the rates of migration of the (10¯1 4) plane of a single-crystal of calcite dissolving in 0.1 M NaCl aqueous solutions at room temperature. The solution pH and PCO 2 controlled in the ranges 4.4 < pH < 12.2 and 0 < PCO 2 < 10-3.5 atm (ambient), respectively. Measured step velocities were compared with the mineral dissolution rates determined from the calcium fluxes. The step velocity is defined as the average of the velocities of the obtuse and acute steps. Rates of step motion increased gradually from 1.4(±0.2) at pH 5.3 to 2.4(±0.3) nm s-1 at pH 8.2, whereas the rates inverted and decreased to the minimum value of 0.69(±0.18) nm s-1 at pH 10.8. For pH > 10.8, only the velocity of the obtuse steps increased as pH increased, whereas that of acute steps gradually decreased.The dissolution rate of the mineral can be calculated from the measured step velocities and average slope, which is proportional to the concentration of exposed monomolecular steps on the surface. The average slope of the dissolving mineral, measured at pH 5.6 and 9.7, was 0.026 (±0.015). Using this slope, we calculate bulk dissolution rates for 5.3 < pH < 12.2 of 4.9(±3.0) × 10-11 to 1.8(±1.0) × 10-10 mol cm-2 s-1. The obtained dissolution rate can be expressed by the following empirical equation:Rdss = 10-4.66(±0.13)[H+] + 10-3.87(±0.06)[HCO3 -] + 10-7.99(plusmn; 0.08)[OH-]We propose that calcite dissolution in these solutions is controlled by elementary reactions that are similar to those that control the dissolution of other amphoteric solids, such as oxides. The mechanisms include the proton-enhanced hydration and detachment of calcium-carbonate ion pairs. The detachments are enhanced by the presence of adsorbed nucleophiles, such as hydroxyl and bicarbonate ions, and by protons adsorbed to key oxygens. A molecular model is proposed that illustrates these processes.  相似文献   

20.
Twelve goethite samples with different degrees of substitution of Al for Fe were synthesized at 22-48 °C and pH values of 1.5-14 under closed system conditions and used to study the effects of Al substitution on the hydrogen isotopic fractionation between goethite and its ambient water. The syntheses followed two pathways: (1) Fe3+ hydrolysis in high pH aqueous solutions; (2) oxidation of Fe2+ to Fe3+ in mid to low pH solutions. XRD and SEM analyses indicated that, irrespective of temperature and pH, goethite was the predominant product of the syntheses in all of the experiments (with degrees of Al substitution as high as ∼13 mol %). “High temperature nonstoichiometric” (HTN) water is present in all of the samples and rapidly exchanges D/H with ambient vapor at room temperature. Uncertainties in the value of the apparent D/H fractionation factor (αe-v) between HTN water and ambient exchange water at 22 °C lead to significant uncertainties in determinations of the δD values of structural hydrogen (δDs) in goethites which contain high proportions of HTN water. As determined for the samples of this study, αe-v has a nominal value of 0.942 (±0.02). δDs values determined using an αe-v value of 0.942 indicate that Al substitution increases the δD value of structural hydrogen in goethite by about 1.4 (±0.4)‰ for each increase in Al of 1 mol %. This dependence on Al is of the same sign as, but somewhat larger in magnitude than, the effect of Al predicted by a published model (∼0.7‰ per mol % Al). The overall uncertainties in the current results suggest that an increase of ∼1‰ per mol % Al, as adopted by previous studies, may be a reasonable estimate with which to adjust δ Ds values of natural goethites to those of the pure FeOOH endmember and could be valid for degrees of Al substitution of up to at least 15 mol %. These synthesis experiments also yield a hydrogen isotopic fractionation factor (DαG-W) between pure goethite (α-FeOOH) and liquid water of 0.900 (±0.006), which is analytically indistinguishable from the published value of 0.905 (±0.004). Thus, use of an DαG-W value of 0.905 in applications to the FeOOH component of natural goethites is supported by the current study.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号