首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 578 毫秒
1.
为了研究轻量土的主动土压力特性,通过开展大比尺刚性挡土墙模型试验,采用人工控制挡土墙位移的方式,分析轻量土作为墙后填土时的主动土压力分布规律。结果表明:轻量土的侧向土压力随着挡墙位移量的增加先降低后逐渐趋于稳定,侧向土压力在挡墙位移量为3 mm时初步达到稳定状态,对比发现轻量土的主动土压力显著小于重塑黄土,这表明轻量土可以有效降低墙背主动土压力。轻量土的主动土压力系数处于0~0.16之间,沿着挡墙分布较为稳定,而重塑黄土主动土压力系数介于0~0.57之间,显著大于轻量土的主动土压力系数。经朗肯理论值与模型试验值对比分析,发现轻量土的朗肯主动土压力小于试验值,理论值与试验值之间的绝对误差处于0~6.32 kPa之间,其在实际工程中可以忽略不计。鉴于模型试验中墙背与填土之间存在一定的摩擦,朗肯理论在计算轻量土的主动土压力时仍较为准确。通过模型试验研究和传统理论分析,揭示了轻量土的主动土压力特性,对于完善轻量土土压力理论具有重要意义。  相似文献   

2.
二级悬臂式挡墙由2个单级悬臂式挡墙呈上下砌垛方式组成。该结构不仅具有单级挡墙型式简单、占地少、对地基承载力要求不高、经济指标好和施工方便等一系列的特点,而且弥补了单级挡墙限制高度的缺点,同时具有重力式挡墙的一些优点,在工程中逐步得到了应用。以库伦土压力理论为基础结合物部-冈部法分别计算了峰值加速度为0.2g、0.3g和0.4g时,二级悬臂式挡墙在分级墙背理论和整体墙背理论下,上墙和下墙的地震主动土压力,并与同高度的单级悬臂式挡墙地震土压力进行了比较。结果表明:二级悬臂式挡墙受力更优,是1种较优的抗震支挡结构,分析结果可为二级悬臂式挡土墙的抗震设计提供参考。  相似文献   

3.
地震作用下重力式挡土墙土压力特性数值模拟研究   总被引:4,自引:1,他引:3       下载免费PDF全文
重力式挡土墙在地震作用下的土压力特性一直是挡土墙设计的重要内容。本文通过数值模拟,在挡土墙墙背轴线上设置一系列监测点,得到地震过程中监测点的加速度、土压力强度时程曲线;然后根据时程曲线分析墙后土压力强度分布特征、根据土压力强度分布求出总土压力、根据总土压力求出其对墙趾的力矩;最后分别将土压力强度分布、总土压力、总土压力对墙趾的力矩与现有的研究方法及规范对比。结果表明:地震作用下墙背各点加速度峰值在同时刻发生,但土压力峰值不在同时刻发生;现有的一些研究方法未考虑土压力强度峰值时程变化,其结果比实际偏大;在低地震烈度条件下,规范计算的总土压力及倾覆力矩偏于保守,而在高烈度条件下则偏于危险。  相似文献   

4.
岩石场地重力式挡土墙地震土压力振动台实验研究   总被引:5,自引:0,他引:5  
结合汶川震区调查资料,利用大型振动台模型试验,分析了碎石土填料的岩石场地重力式挡土墙的地震土压力及其分布规律,并以此对我国现行铁路、公路抗震规范做合理性讨论和细化。研究发现,地震作用下,挡土墙的动土压力沿墙高呈单峰曲线状分布,且60%~80%集中作用于挡墙中部;随着地震峰值加速度的增加,地震土压力分布逐渐偏离现行振震设计规范所认为的三角形线性状,而呈现非线性状;合力作用点高于1/3墙高,0.4g地震加速度作用下,接近0.4倍墙高,对岩石场地下粗粒径墙背填料的地震土压力作用点高度,建议取0.35倍墙高。对比计算表明,现行规范能基本满足工程抗震设计需要,但建议对柔性挡土墙的抗震设计作出必要规定。  相似文献   

5.
土质场地重力式挡土墙地震土压力振动台实验研究   总被引:3,自引:0,他引:3  
汶川震区路基挡土墙震害表明,地震动荷载作用下重力式挡墙的位移、破坏与基础场地形式有关,除岩质场地和土质场地挡墙所共有的外倾形式,土质地基挡土墙还表现有整体推移及下部向外推移的倾转变形等复杂模式,因此地震土压力大小及分布也将受到这种复杂土-结相互作用的影响。基于碎石土及风化花岗岩填料的土质场地重力式挡土墙大型振动台模型实验,对挡土墙地震土压力及变形模式开展了对比研究,发现在强震作用下,土质地基挡墙因基础约束较弱而产生位移,并伴随明显的墙—土分离现象,致使实测地震土压力较之抗震设计规范计算值偏小(0.4g峰值加速度下约小6%~15%),但作用点高度变化不大。由实验结果与现行抗震规范计算值的安全系数对比,认为对土质场地挡墙的地震土压力计算,按现行国内抗震设计规范基本能满足实际工程抗震设计需要;对于地震区挡墙设计,在允许挡墙发生少量容许位移的前提下可采用内摩擦角较大、自稳能力更好的墙背填料以减少地震土压力。  相似文献   

6.
挡土墙地震被动土压力的拟动力分析   总被引:5,自引:0,他引:5  
杨剑 《地震学刊》2012,(3):365-371
对地震土压力的研究是地震区挡土墙安全设计的一项重要课题。地震条件下,目前的研究主要是给出了土压力的近似拟静力解析解。本文采用可考虑动力荷载下的周期和纵波及横波效应的拟动力方法,对挡土墙后的地震被动土压力进行分析。在挡土墙后平面滑裂面假设的基础上,考虑了水平和垂直向地震加速度、纵波速度、横波速度、挡土墙摩擦角、填土内摩擦角、填土坡角对地震被动土压力的影响。与Mononobe-Okabe理论的拟静力法不同的是,用本方法得出了沿墙身地震被动土压力是非线性变化的结果,这更符合地震条件下土压力的变化规律。  相似文献   

7.
土工格栅加筋挡土墙是一种柔性挡土结构,目前尚未建立较严密的设计方法,作用在土工格栅加筋墙壁上的地震动土压力研究是抗震设计的重要内容之一。应用基于拉格朗日法的完全非线性动有限差分法研究整体面板式土工格栅加筋土挡壁在地震作用下各设计参数对挡壁动土压力的影响。采用弹塑性模型模拟填土,采用耦合弹性参数描述格栅与土接触界面特性,参数包括加筋间距、长度、刚度、地震强度和填土性质等,分析墙壁的动土压力沿墙身的分布特征,得出了影响地震动土压力的显著参数,证明了土工格栅加筋墙体的优异吸震能力,研究结果为整体面板式土工格栅加筋土挡墙抗震设计中的动土压力研究提供参考。  相似文献   

8.
地震诱发的海啸对沿海围护结构的破坏具有强度大的特点。滨水挡土墙作为重要的围护结构,海啸与地震的联合作用极易造成其发生绕墙踵的被动破坏。采用条分法,将土楔体分割成无数平行于破裂面的刚性土条,并建立绕墙踵转动的挡墙与刚性土条之间的速度容许场。基于极限上限理论,依据外力做功功率等于其内能耗散功率,推导了地震加速度系数的表达式。与经典极限平衡理论相比,该方法考虑了挡墙的位移模式,且无需假设地震土压力的作用位置。分析了浪高与海平面高度之比,内摩擦角φ及墙土摩擦角δ对滨水挡土墙稳定性的影响。  相似文献   

9.
地震土压力评价是挡土墙抗震设计的关键问题之一.以往的研究结果表明,挡墙上地震土压力的大小及分布与墙体的侧向位移或者墙后填土的侧向变形密切相关.经典的物部-冈部地震土压力公式可计算填土处于主动与被动状态的极限平衡条件下的土压力,未考虑挡墙侧向位移或填土侧向变形对土压力的影响.在研究土压力系数随应变增量比变化规律的基础上,本文指出土压力系数与挡土墙位移量之间不存在唯一性关系,发现正常固结填土的土压力系数与以应变增量比表述的填土侧向应变约束条件之间具有良好的唯一性,揭示了压剪耦合效应是土压力形成的物理本质;基于上述的唯一性关系和中间土楔等概念,提出了可考虑填土侧向变形的地震土压力实用计算方法,并通过土压力模型试验结果初步验证了该方法的合理性.  相似文献   

10.
针对黄土地区现有的地震荷载作用下挡土墙土压力计算方法中的不足,进行了4个含水量和3个围压的平面应变试验,首次建立了平面应变强度参数与结构性的关系,扩展了被动状态下考虑应力主轴偏转的粘性土侧土压力系数计算公式,采用水平微分层分析方法,提出了一种地震作用下同时考虑黄土结构性和主应力轴偏转的挡土墙被动土压力计算方法。参数分析结果表明平面应变条件下地震被动土压力均大于三轴条件下,结构性土地震被动土压力大于无结构性土,墙土面有摩擦时地震被动土压力大于墙土面光滑时;地震被动土压力随水平和竖向地震加速度系数的增大而减小、随摩擦角、均布荷载、墙土摩擦角、粘聚力、构度指标的增大而增大。黄土地区地震被动土压力计算应综合考虑平面应变强度参数、结构性和墙土摩擦效应的影响。  相似文献   

11.
In this paper the stability of a tied-back wall subjected to seismic loads is analysed for a predetermined mode of failure (rotation about the top of the wall) and the analysis is compared with data from tests on this type of wall using the seismic simulator at the State University of New York at Buffalo. We carried out a pseudo-static analysis of the problem using the Mononobe-Okabe earth pressure coefficients, wherein the dynamic effects due to the seismic loading are converted into equivalent static loads. The acceleration ratio at which the wall fails by rotation about the top was obtained by considering the moments due to the various lateral earth pressure resultants and the inertial forces induced in the soil due to the seismic loading. We found that the presence of wall friction on the passive side significantly enhances the stability of the flexible retaining wall under seismic loads. Thus, flexible retaining walls supporting dry cohesionless soil can be very efficient during earthquakes. Under moderate earthquakes, an increase in the depth of embedment increases the dynamic factor of safety significantly. However, beyond a certain acceleration ratio for a soil with a particular value of ø, any increase in the depth of emdedment has no effect in impeding failure, irrespective of any change in the geometry of the system. Seismic design charts are presented to evaluate the stability of, and to design, flexible retaining walls embedded in dry cohesionless soils under seismic loading.  相似文献   

12.
At present, methods based on allowable displacements are frequently used in the seismic design of earth retaining structures. However, these procedures ignore both the foundation soil deformability and the seismic amplification of the soil placed behind the retaining wall. Thus, they are not able to predict neither a rotational failure mechanism nor seismic induced lateral displacements with an acceptable degree of accuracy for the most general case. In this paper, a series of 2D finite-element analyses were carried out to study the seismic behavior of gravity retaining walls on normally consolidated granular soils. Chilean strong-motion records were applied at the bedrock level. An advanced non-linear constitutive model was used to represent both the backfill and foundation soil behavior. This elastoplastic model takes into account both the stress dependency of soil stiffness and coupling between shear and volumetric strains. In unloading–reloading cycles, the non-linear shear-modulus reduction with shear strain amplitude is considered. Interface elements were used to model soil–structure interaction. Routine-design charts were derived from the numerical analyses to predict the lateral movements at the base and top of gravity retaining walls located at sites with similar seismic characteristics to the Chilean subduction zone. Thus, wall seismic rotation can also be obtained. The developed charts consider wall dimensions, granular soil properties, bedrock depth, and seismic input motion characteristics. As shown, the proposed charts match well with available experimental data.  相似文献   

13.
Observations from recent earthquakes show that retaining structures with non-liquefiable backfills perform extremely well; in fact, damage or failures related to seismic earth pressures are rare. The seismic response of a 6-m-high braced basement and a 6-m free-standing cantilever wall retaining a compacted low plasticity clay was studied in a series of centrifuge tests. The models were built at a 1/36 scale and instrumented with accelerometers, strain gages and pressure sensors to monitor their response. The experimental data show that the seismic earth pressure on walls increases linearly with the free-field PGA and that the earth pressures increase approximately linearly with depth, where the resultant acts near 0.33 H above the footing as opposed to 0.5–0.6 H, which is suggested by most current design methods. The current data suggest that traditional limit equilibrium methods yield overly conservative earth pressures in areas with ground accelerations up to 0.4g.  相似文献   

14.
In the design procedure for a retaining wall, the pseudo-static method has been widely used and dynamic earth pressure is calculated by the Mononobe–Okabe method, which is an extension of Coulomb’s earth pressure theory computed by force equilibrium. However, there is no clear empirical basis for treating the seismic force as a static force, and recent experimental research has shown that the Mononobe–Okabe method is quite conservative, and there exists a discrepancy between the assumed conditions and real seismic behavior during an earthquake. Two dynamic centrifuge tests were designed and conducted to reexamine the Mononobe–Okabe method and to evaluate the seismic lateral earth pressure on an inverted T-shape flexible retaining wall with a dry medium sand backfill. Results from two sets of dynamic centrifuge experiments show that inertial force has a significant impact on the seismic behavior on the flexible retaining wall. The dynamic earth pressure at the time of maximum moment during the earthquake was not synchronized and almost zero. The relationship between the back-calculated dynamic earth pressure coefficient at the time of maximum dynamic wall moment and the peak ground acceleration obtained from the wall base peak ground acceleration indicates that the seismic earth pressure on flexible cantilever retaining walls can be neglected at accelerations below 0.4 g. These results suggest that a wall designed with a static factor of safety should be able to resist seismic loads up to 0.3–0.4 g.  相似文献   

15.
Using finite-element modelling, this paper explores the magnitude and distribution of dynamic earth pressures on several types of flexible retaining systems: L-shaped reinforced-concrete walls, piled walls with horizontal or with strongly inclined anchors, and reinforced-soil walls. The utilized base excitation is typical of earthquake motions of either high or moderately low dominant frequencies having a peak ground acceleration (PGA) of 0.40 g and relatively short duration. Linear as well as non-linear (Mohr–Coulomb) soil behaviour is investigated, under dry conditions. The results show that, as the degree of realism in the analysis increases, we can explain the frequently observed satisfactory performance of such retaining systems during strong seismic shaking.  相似文献   

16.
The effects of earthquakes on cantilever retaining walls with liquefiable backfills were studied. The experimental techniques utilized in this study are discussed here. A series of centrifuge tests was conducted on aluminum, fixed-base, cantilever wall models retaining saturated, cohesionless backfills. Accelerations on the walls and in the backfill, static and excess pore pressures in the soil, and deflections and bending strains in the wall were measured. In addition, direct measurements of static and dynamic lateral earth pressures were made. In some tests, sand backfills were saturated with the substitute pore fluid metolose. Modeling of model type experiments were conducted. The experimental measurements were found internally consistent and repeatable. Both static and dynamic earth pressure measurements were determined to be reliable. It was also observed that for the test configuration adopted, a special boundary treatment such as the use of duxseal is optional. Static and seismic modeling of models were also successful, which indicated that the assumed scaling relations were essentially correct.  相似文献   

17.
2022年1月8日门源M6.9地震造成山丹明长城局部破坏。为研究此次地震作用下夯土城墙的动力响应与破坏特征,基于地震现场考察结果,采用振幅等效处理后的记录地震波为输入地震动,开展双向地震荷载作用下夯土城墙的动力响应数值分析,研究不同位置测点的最大位移、峰值加速度与墙体应力分布特征,探讨地震导致夯土城墙破坏的主要内因。研究结果表明:双向地震荷载作用下,墙体位移和峰值加速度(PGA)随着高度的增加逐渐增加,但距墙体底部0.5 m高度范围内PGA放大效应不明显,最大位移、加速度均出现在墙体顶部裂缝位置处;水平地震荷载作用下墙体的地震动响应更为显著;墙体的最大主应力、最大剪应力均出现在有裂缝处的底端掏蚀悬空部位,墙体裂缝、夯筑搭接、掏蚀悬空处应力集中明显;裂缝对夯土城墙的地震动放大效应在一定高度范围内表现为弱化作用,但随高度增加逐渐过渡为强化作用;裂缝可显著增强墙体顶部地震动响应,可能是本次地震诱发城墙破坏的主要内因。研究成果可为古城墙遗址的加固修缮提供科学指导。  相似文献   

18.
Seismic active pressure distribution history behind rigid retaining walls   总被引:1,自引:0,他引:1  
Evaluating the seismic active earth pressure on retaining walls is currently based on pseudo-static method in practices. In this method, however, it is not simple, choosing an appropriate value for earthquake coefficient, which should fully reflect the dynamic characteristics of both soil and loading is an important problem. On the other hand, by using only two extra dynamic parameters that are shear wave velocity of soil and predominant frequency of probable earthquake, one can benefit from another more accurate tool called pseudo-dynamic method to solve the problem of earth pressure.In this study in the framework of limit equilibrium analysis, pseudo-dynamic method has been applied into horizontal slice method of analysis to account for the effect of earthquake on lateral earth pressure history behind rigid retaining walls. The pressure history resulted from a number of analyses shows that before and after reaching the peak resultant force, different pressure distributions occur behind a wall that put more local pressure than the same at peak. This method would be a tool to control this phenomenon in wall design.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号