共查询到20条相似文献，搜索用时 203 毫秒
1.
基于人工交叉裂隙模型,通过室内透水试验,得到了不同进口与出口组合时的流量和压力变化的关系曲线。同时结合串联裂隙水力学开度的计算公式,利用最小二乘法求解超静定方程组,计算交叉裂隙中每个裂隙单元的水力学开度。通过拓扑得到裂隙交叉点的几何尺寸,并求解Navier-Stokes方程,研究裂隙交叉对其水力特性的影响。结果表明,通过室内试验和串联裂隙水力学开度计算公式相结合的方法,可以准确计算每个裂隙单元的水力学开度。当雷诺数Re较小时,交叉点内部的流体成稳态层流流动;当雷诺数较大（比如Re≥100）时,可以观测到明显的漩涡,说明流体的惯性力远大于黏性力,经典的立方定律不再适用。对于1个进口2个出口的情况,出口的流量分配比率与雷诺数成二次函数关系,随着雷诺数的增大,流量分配比率的非线性越来越明显,其最大分配比率变化超过15%。出口的水力学开度e与初始水力学开度（即力学开度E0）的比值e/E0和雷诺数Re也具有二次函数关系。当Re10时,e/E0呈现出较强的非线性;利用该关系式可以得到修正的立方定律,从而进一步求解交叉裂隙的水力特性问题。 相似文献
2.
等效水力隙宽和水力梯度对岩体裂隙网络非线性渗流特性的影响 总被引：1，自引：0，他引：1
等效水力隙宽和水力梯度是影响岩体裂隙网络渗流特性的重要因素。制作裂隙网络试验模型,建立高精度渗流试验系统;求解纳维-斯托克斯方程,模拟流体在裂隙网络内的流动状态,研究等效水力隙宽和水力梯度对非线性渗流特性的影响。结果表明,当水力梯度较小时,等效渗透系数保持恒定的常数,流体流动属于达西流动区域,流量与压力具有线性关系,可采用立方定律计算流体流动;当水力梯度较大时,等效渗透系数随着水力梯度的增加而急剧减少,流体流动进入强惯性效应流动区域,流量与压力具有强烈的非线性关系,可采用Forchheimer方程计算流体流动。随着等效水力隙宽的增加,区别线性和非线性流动区域的临界水力梯度呈幂函数关系递减。当水力梯度小于临界水力梯度时,控制方程可选立方定律;当水力梯度大于临界水力梯度时,控制方程可选Forchheimer方程,其参数A和B可根据经验公式计算得到。其研究结果可为临界水力梯度的确定及流体流动控制方程的选取提供借鉴意义。 相似文献
3.
《岩土力学》2017,(11):3332-3340
针对裂隙岩体的非饱和渗流问题,基于离散裂隙网络模型并结合非饱和Darcy定律、Richards方程、非饱和本构模型以及Signorini型饱和-非饱和互补溢出边界,提出了离散裂隙网络非饱和渗流问题的数学模型。采用有限单元法建立了裂隙网络非饱和渗流模型的数值求解格式和对应的迭代算法。通过与矩形坝稳定渗流、一维竖直裂隙非饱和入渗以及室内二维瞬态排水渗流的试验、数值及理论结果对比分析,验证了文中算法的有效性;根据流量等效原则,指出了裂隙网络模型应用于求解连续介质非饱和渗流问题的有效性。验证了该算法对于求解裂隙边坡降雨入渗问题的可靠性,揭示了降雨入渗过程裂隙网络流量分布的非均匀性及裂隙产状对降雨入渗流动具有重要的控制作用。 相似文献
4.
采用渗流力学理论并结合Monte Carlo方法描述岩体裂隙的随机分布,研究渗流模型的尺寸效应并确定表征单元体积（REV）,得到了3种开口度分布形式的等效渗透系数椭圆曲线,建立了等效渗透系数方向性的判别标准。离散裂隙网络（DFN）模型假定流体只在岩体裂隙内部流动,而不通过岩体本身渗流。基于二维离散元程序UDEC并进行二次开发,建立DFN模型,通过改变流体的流动方向,得到不同流动方向下岩体裂隙网络的等效渗透系数,并分析不同的开口度分布形式对岩体裂隙网络等效渗透系数方向性的影响。计算结果表明,表征单元体积存在的条件是等效渗透系数保持稳定且渗透椭圆比较光滑。等效渗透系数的方向性受开口度分布形式的影响很大：当开口度-长度关联分布时,等效渗透系数各向异性;当开口度对数正态分布时,等效渗透系数各向同性;当开口度恒定分布时,等效渗透系数的特性介于二者之间。变化系数（CV）是否大于5%是判定岩体裂隙网络渗透系数是否具有方向性的判别标准。 相似文献
5.
基于离散裂隙网络模型的裂隙水渗流计算 总被引：1，自引：1，他引：0
离散裂隙网络模型(Discrete Fracture Network（DFN）)是研究裂隙水渗流最为有效的手段之一。文章根据裂隙几何参数和水力参数的统计分布,利用Monte Carlo随机模拟技术生成二维裂隙网络,基于图论无向图的邻接矩阵判断裂隙网络的连通,利用递归算法提取出裂隙网络的主干网或优势流路径。基于立方定律和渗流连续性方程,利用数值解析法建立了二维裂隙网络渗流模型,分析不同边界条件下裂隙网络中的流体流动。结果表明,该方法可以模拟区域宏观水力梯度和边界条件下,裂隙网络水力梯度方向总的流量,以及节点的水位、节点间的流量和流动方向的变化特征,为区域岩溶裂隙水渗流计算提供了一种实用、可行的方法。 相似文献
6.
岩体粗糙裂隙非线性渗透特性是岩体渗流研究的重要课题。针对Javadi所提T模型中亚裂隙中速度恒定这一假设的不足,将其修正为速度与开度成正比的经验关系,考虑黏性压降和局部压降,提出了新的低速下粗糙裂隙非线性渗流模型（MT模型）。为了验证MT模型的正确性,对5种不同粗糙裂隙进行了低流量的饱和渗流试验,将现有模型及MT模型的预测值与试验结果进行对比,分析表明MT模型与试验结果更为吻合,且模型适用于粗糙性系数JRC≤10的低粗糙度裂隙,雷诺数小于1 000的低流速情况。对MT模型进行分析,初步揭露了粗糙裂隙的非线性渗流机制,即小雷诺数下的Darcy流和大雷诺数下的Forchheimer流,并用临界雷诺数区分两种流动行为。分析了裂隙的粗糙度和开度对非线性渗流特性的影响,表明裂隙越粗糙或开度越小,则临界雷诺数越小,非线性作用将越强。提出了临界雷诺数与水力开度和绝对粗糙度的经验关系式,同时指出该关系式适用于JRC≤10的低粗糙度裂隙。 相似文献
7.
考虑应力历史的岩石单裂隙渗流特性试验研究 总被引：1，自引：0，他引：1
通过开展单裂隙花岗岩不同围压加、卸载和不同水力梯度作用下的渗透试验,研究应力历史对裂隙渗透性能演化的影响。试验结果表明：在围压加载过程中,渗流流量与渗透压差大致呈线性关系;在渗透压差相同的条件下,围压越小,流量越大,随着围压上升,裂隙渗流流量持续减小,但随着围压的进一步增大,流量的减小有减缓的趋势。在围压相同以及渗透压差相同的条件下,单裂隙花岗岩在卸载条件下的渗流特性与加载条件下相比,其渗流流量明显降低,且卸载过程中渗流流量与渗透压差开始偏离线性关系。从试验前、后裂隙面粗糙度系数值的对比可以看出,由于法向应力挤压以及渗流流体的冲蚀作用,试验后裂隙面粗糙度系数明显降低。卸载的过程中,裂隙渗透性能的恢复具有明显的滞后效应,表明在法向应力和流体冲蚀的共同作用下,裂隙产生了不可恢复的非弹性变形。 相似文献
8.
考虑岩体裂隙渗流变水温影响,推导单裂隙变水温水流近似解析解和有限元解,在此基础上分别建立裂隙二维网络变水温渗流数值求解方程,分别对应裂隙网络变水温渗流分析的近似解析法和子结构法。分析变温水流运动规律发现：（1）单裂隙内水流水头与水力坡降成非线性关系,当水流由高温区向低温区流动时,水头分布曲线为凸曲线,此时按线性渗流简化水头整体偏小;当由低温区向高温区流动时,水头分布曲线为凹曲线,此时按线性渗流简化水头整体偏大。（2）单裂隙内,高水温处水力坡降小,低水温处水力坡降大;裂隙平均水温越高,流速越快;裂隙网络内存在与裂隙宽度相似的温度偏流效应,即交叉节点水流有偏向水流温度高的裂隙流动的趋势。在温度较高和温度梯度较大的区域,应该考虑水流温度变化对渗流场的影响。 相似文献
9.
《岩土力学》2016,(1):219-228
岩体裂隙粗糙度和流体惯性效应是影响岩体裂隙网络等效渗透性的重要因素。首先回顾了单裂隙中裂隙粗糙度和流体惯性效应对其过流能力的影响;然后基于逆Broyden秩1拟牛顿迭代法求解控制裂隙内流体流动的非线性方程组,研究岩体裂隙粗糙度和流体惯性效应对离散裂隙网络(DFN)等效渗透性的影响;最后,基于两种不同边界条件,对离散裂隙网络模型内流体的流动特性进行了探讨。结果表明,当水力梯度较小(0.5)时,裂隙粗糙度和流体惯性效应对离散裂隙网络渗透性的影响很小;当水力梯度较大(0.5)时,裂隙粗糙度和流体惯性效应对离散裂隙网络渗透性的影响随水力梯度的变化而显著变化;在两种边界条件下,当水力梯度在0.1~10.0之间时,裂隙粗糙度和流体惯性效应对离散裂隙网络过流能力的最大影响分别为18.1%和27.5%。所以,当水力梯度较大时,需要在离散裂隙网络模型的渗流计算中考虑裂隙粗糙度和流体惯性效应的影响。 相似文献
10.
由于存在大量粗糙不规则裂隙,使得岩体中流体运动极为复杂。针对天然粗糙岩石裂隙渗流试验存在物理模型隐蔽性和不可重复性等难点,基于三维Weierstrass-Mandelbrot分形函数构建了粗糙节理面的裂隙通道,采用3D打印技术获得了透明精细的裂隙模型,使用微流体控制仪研究了不同试验条件下的裂隙渗流扩散运动,分析了裂隙通道流量与压力水头、裂隙宽度和分形维数之间的关系。研究结果表明：与平行板立方定律近似,在分形裂隙中,裂隙通道流量与压力水头成线性关系;单宽流量与裂隙通道的宽度成近似的三次方关系;考虑分形维数影响时,相同条件下流过裂隙通道的流量随着分形维数的增加而增加;粗糙裂隙渗流立方定律可采用与分形维数相关的幂指数函数进行修正。 相似文献
11.
We present a discussion of the state-of-the-art on the use of discrete fracture networks (DFNs) for modelling geometrical characteristics, geomechanical evolution and hydromechanical (HM) behaviour of natural fracture networks in rock. The DFN models considered include those based on geological mapping, stochastic generation and geomechanical simulation. Different types of continuum, discontinuum and hybrid geomechanical models that integrate DFN information are summarised. Numerical studies aiming at investigating geomechanical effects on fluid flow in DFNs are reviewed. The paper finally provides recommendations for advancing the modelling of coupled HM processes in fractured rocks through more physically-based DFN generation and geomechanical simulation. 相似文献
12.
Multi-borehole pumping and tracer tests on the 10 to 100-m scale were conducted in a fractured chalk aquitard in the Negev
Desert, Israel. Outcrop and core fracture surveys, as well as slug tests in packed-off intervals, were carried out at this
site to obtain the parameters needed for construction of a stochastic discrete fracture network (DFN). Calibration of stochastic
DFNs directly to the multiple borehole test data was inadequate. Instead, two equivalent deterministic DFN flow models were
used: the vertical-fractures (VF) model, consisting of only vertical fractures, and the fractures’ intersections (INT) model,
consisting of vertical and horizontal fractures with enhanced transmissivity at their intersections. Both models were calibrated
against the multi-borehole response of one pumping test and their predictions were tested against three other independent
pumping tests. The average accuracies of all transient drawdown predictions of the VF and INT models were 65 and 66%, respectively.
In contrast to this equality in average drawdown predictions of both models, the INT model predicted better important breakthrough
curve features (e.g., first and peak arrival times), than the VF model. This result is in line with previously assumed channeled
flow, derived from analytical analysis of these pumping and tracer tests.
Ronit Nativ, deceased, may her memory be blessed. 相似文献
13.
Fracture networks play a more significant role in conducting fluid flow and solute transport in fractured rock masses, comparing with that of the rock matrix. Accurate estimation of the permeability of fracture networks would help researchers and engineers better assess the performance of projects associated with fluid flow in fractured rock masses. This study provides a review of previous works that have focused on the estimation of equivalent permeability of two-dimensional (2-D) discrete fracture networks (DFNs) considering the influences of geometric properties of fractured rock masses. Mathematical expressions for the effects of nine important parameters that significantly impact on the equivalent permeability of DFNs are summarized, including (1) fracture-length distribution, (2) aperture distribution, (3) fracture surface roughness, (4) fracture dead-end, (5) number of intersections, (6) hydraulic gradient, (7) boundary stress, (8) anisotropy, and (9) scale. Recent developments of 3-D fracture networks are briefly reviewed to underline the importance of utilizing 3-D models in future research. 相似文献
14.
15.
Cubic law with aperture-length correlation: implications for network scale fluid flow 总被引：2，自引：2，他引：0
Christian Klimczak Richard A. Schultz Rishi Parashar Donald M. Reeves 《Hydrogeology Journal》2010,18(4):851-862
Previous studies have computed and modeled fluid flow through fractured rock with the parallel plate approach where the volumetric flow per unit width normal to the direction of flow is proportional to the cubed aperture between the plates, referred to as the traditional cubic law. When combined with the square root relationship of displacement to length scaling of opening-mode fractures, total flow rates through natural opening-mode fractures are found to be proportional to apertures to the fifth power. This new relationship was explored by examining a suite of flow simulations through fracture networks using the discrete fracture network model (DFN). Flow was modeled through fracture networks with the same spatial distribution of fractures for both correlated and uncorrelated fracture length-to-aperture relationships. Results indicate that flow rates are significantly higher for correlated DFNs. Furthermore, the length-to-aperture relations lead to power-law distributions of network hydraulic conductivity which greatly influence equivalent permeability tensor values. These results confirm the importance of the correlated square root relationship of displacement to length scaling for total flow through natural opening-mode fractures and, hence, emphasize the role of these correlations for flow modeling. 相似文献
16.
17.
Groundwater flow in fractured rocks is modeled using a coupled model based on the domain decomposition method. In the model, the fractured porous medium is divided into two non-overlapping sub-domains. One is the rock matrix, in which the medium is described using a continuum model. The other consists of deep fractures and fissure zones, where the medium is described using a discrete fracture network (DFN) model. The two models are coupled through the continuity of the hydraulic heads and fluxes on the common boundaries. The coupled model is used to simulate groundwater flow in a hydropower station. The results show that the model simulates groundwater levels that are in agreement with the measured groundwater levels. Furthermore, the model’s parameters relating to deep fractures and fissure zones are verified by comparing three different models (the continuum model, coupled model, and DFN model). The results show that the coupled model can capture and duplicate the hydrogeological conditions in the study domain, whereas the continuum model overestimates and the DFN model underestimates the measured hydraulic heads. A sensitivity analysis shows that fracture aperture has a considerable effect on the groundwater level. So, when the fracture aperture is large, the coupled model or DFN model is more appropriate than the continuum model in the fracture domain. 相似文献
18.
Trullenque Ghislain Parashar Rishi Delcourt Clément Collet Lucille Villard Pauline Potel Sébastien 《Hydrogeology Journal》2017,25(3):813-827
Results of a series of deformation experiments conducted on gabbro samples and numerical models for computation of flow are presented. Rocks were subjected to triaxial tests (σ1 > σ2 = σ3) under σ3 = 150 MPa confining pressure at room temperature, to generate fracture network patterns. These patterns were either produced by keeping a constant confining pressure and loading the sample up to failure (conventional test: CT), or by building up a high differential stress and suddenly releasing the confining pressure (confining pressure release test: CPR). The networks are similar in overall density but differ primarily in the orientation of smaller fractures. In the case of CT tests, a conjugate fracture set is observed with one dominant fracture zone running at about 20° from σ1. CPR tests do not show such a conjugate pattern and the mean fracture orientation is at around 35° from σ1. Discrete fracture network (DFN) methodology was used to determine the distribution of flow and hydraulic head for both fracture sets under simple boundary conditions and uniform transmissivity values. The fracture network generated by CT and CPR tests exhibit different patterns of flow field and hydraulic head configurations, but convey approximately the same amount of flow at all scales for which DFN models were simulated. The numerical modelling results help to develop understanding of qualitative differences in flow distribution that may arise in rocks of the same mineralogical composition and mechanical properties, but under the influence of different stress conditions, albeit at similar overall stress magnitude.
相似文献19.
裂隙是油气储层主要的储集空间及流体渗流通道,影响油气的运移规律,是油气勘探开发的重要指标。以冀中坳陷任丘油田任10井为例,运用数值模拟方法研究了裂隙开展宽度和裂隙面粗糙度对岩石渗流特性的影响规律。研究结果表明,(1)裂隙开展宽度较小时,孔隙内流体压力仅在入口处小范围内呈扇形分布,裂隙中压力分布曲线呈正切函数型,流体流速在裂隙和孔隙中都较小;随着裂缝开展宽度的增加,孔隙内流体压力逐渐增大,裂隙中压力分布曲线逐渐向直线型转变,流体流速在入口处先减小后稳定,在裂隙中先增加后稳定;(2)裂隙面粗糙度对裂隙岩石渗流特性的影响与裂隙开展宽度有关,在裂隙开展宽度较大时,裂隙面粗糙度对流体压力的分布影响较大;随着裂隙面粗糙度增大,孔隙内流速逐渐增大,而裂隙中流速逐渐减小;(3)随着裂隙开展宽度的增大,影响裂隙流体流动的主控因素逐渐由裂隙开展宽度转变为裂隙面粗糙度。 相似文献
20.
Correlations Developed for Estimation of Hydraulic Parameters of Rough Fractures Through the Simulation of JRC Flow Channels 总被引：3，自引：1，他引：2
The hydro-mechanical response of fractured rock masses is complex, due partly to the presence of fractures at different scales.
Surface morphology has a significant influence on fluid flow behaviour of a fracture. Different empirical correlations and
statistical models have been proposed to estimate the equivalent hydraulic aperture and determine the pressure drop along
a fracture. However, the existing models suffer from not being adequately generalised to be applicable to a wide range of
real fracture surfaces. To incorporate the effect of profile roughness in the hydro-mechanical behaviour of fractured rock
masses, the joint roughness coefficient (JRC) is the most widely used empirical approach. However, the average JRC of two
fracture walls in fluid flow analysis, as is a common practice, appears to be inappropriate. It will be shown how different
combinations of pairs of JRCs could lead to a similar JRC value. Also, changing the position of the top and bottom walls of
a fracture can significantly change the hydraulic response of the fracture while the average JRC is identical in both cases.
In this paper, correlations are developed which are based on the simulation of JRCs using estimated fluid flow parameters
of 2D fractures can be estimated. In order to widen the application range of the correlations, JRC flow channels were generated:
these are 2D channels with their top and bottom walls being made from two of the JRC profiles. To estimate the JRC of linear
profiles, a correlation developed between JRC and a newly developed Riemannian roughness parameter, D
R1, is proposed. Considering ten JRC profiles, a total of 100 JRC flow channels were generated. In order to only investigate
the effect of surface roughness on fluid flow, the minimum closure between the top and bottom walls of JRC flow channels were
considered to be constant. Three cases with minimum closures of 0.01, 0.05 and 0.10 cm were considered in this study. All
JRC flow channels were subjected to fluid analysis using FLUENT software. Based on these results, correlations were developed
between the geometrical and hydraulic properties of flow channels. Analysis of several real fractures demonstrated the applicability
of these correlations. 相似文献