首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 828 毫秒
1.
The geological storage of carbon dioxide is considered as one of the measures to reduce greenhouse gas emissions and to mitigate global warming. Operators of storage sites are required to demonstrate safe containment and stable behaviour of the storage complex that is achieved by geophysical and geochemical monitoring, combined with reservoir simulations. For site characterization, as well as for imaging the carbon dioxide plume in the reservoir complex and detecting potential leakage, surface and surface‐borehole time‐lapse seismic monitoring surveys are the most widespread and established tools. At the Ketzin pilot site for carbon dioxide storage, permanently installed fibre‐optic cables, initially deployed for distributed temperature sensing, were used as seismic receiver arrays, demonstrating their ability to provide high‐resolution images of the storage formation. A vertical seismic profiling experiment was acquired using 23 source point locations and the daisy‐chained deployment of a fibre‐optic cable in four wells as a receiver array. The data were used to generate a 3D vertical seismic profiling cube, complementing the large‐scale 3D surface seismic measurements by a high resolution image of the reservoir close to the injection well. Stacking long vibro‐sweeps at each source location resulted in vertical seismic profiling shot gathers characterized by a signal‐to‐noise ratio similar to gathers acquired using geophones. A detailed data analysis shows strong dependency of data quality on borehole conditions with significantly better signal‐to‐noise ratio in regions with good coupling conditions.  相似文献   

2.
Distributed acoustic sensing is an emerging technology using fibre‐optic cables to detect acoustic disturbances such as flow noise and seismic signals. The technology has been applied successfully in hydraulic fracture monitoring and vertical seismic profiling. One of the limitations of distributed acoustic sensing for seismic recording is that the conventional straight fibres do not have broadside sensitivity and therefore cannot be used in configurations where the raypaths are essentially orthogonal to the fibre‐optic cable, such as seismic reflection methods from the surface. The helically wound cable was designed to have broadside sensitivity. In this paper, a field trial is described to validate in a qualitative sense the theoretically predicted angle‐dependent response of a helically wound cable. P‐waves were measured with a helically wound cable as a function of the angle of incidence in a shallow horizontal borehole and compared with measurements with a co‐located streamer. The results show a similar behaviour as a function of the angle of incidence as the theory. This demonstrates the possibility of using distributed acoustic sensing with a helically wound cable as a seismic detection system with a horizontal cable near the surface. The helically wound cable does not have any active parts and can be made as a slim cable with a diameter of a few centimetres. For that reason, distributed acoustic sensing with a helically wound cable is a potential low‐cost option for permanent seismic monitoring on land.  相似文献   

3.
A modular borehole monitoring concept has been implemented to provide a suite of well‐based monitoring tools that can be deployed cost effectively in a flexible and robust package. The initial modular borehole monitoring system was deployed as part of a CO2 injection test operated by the Southeast Regional Carbon Sequestration Partnership near Citronelle, Alabama. The Citronelle modular monitoring system transmits electrical power and signals, fibre‐optic light pulses, and fluids between the surface and a reservoir. Additionally, a separate multi‐conductor tubing‐encapsulated line was used for borehole geophones, including a specialized clamp for casing clamping with tubing deployment. The deployment of geophones and fibre‐optic cables allowed comparison testing of distributed acoustic sensing. We designed a large source effort (>64 sweeps per source point) to test fibre‐optic vertical seismic profile and acquired data in 2013. The native measurement in the specific distributed acoustic sensing unit used (an iDAS from Silixa Ltd) is described as a localized strain rate. Following a processing flow of adaptive noise reduction and rebalancing the signal to dimensionless strain, improvement from repeated stacking of the source was observed. Conversion of the rebalanced strain signal to equivalent velocity units, via a scaling by local apparent velocity, allows quantitative comparison of distributed acoustic sensing and geophone data in units of velocity. We see a very good match of uncorrelated time series in both amplitude and phase, demonstrating that velocity‐converted distributed acoustic sensing data can be analyzed equivalent to vertical geophones. We show that distributed acoustic sensing data, when averaged over an interval comparable to typical geophone spacing, can obtain signal‐to‐noise ratios of 18 dB to 24 dB below clamped geophones, a result that is variable with noise spectral amplitude because the noise characteristics are not identical. With vertical seismic profile processing, we demonstrate the effectiveness of downgoing deconvolution from the large spatial sampling of distributed acoustic sensing data, along with improved upgoing reflection quality. We conclude that the extra source effort currently needed for tubing‐deployed distributed acoustic sensing vertical seismic profile, as part of a modular monitoring system, is well compensated by the extra spatial sampling and lower deployment cost as compared with conventional borehole geophones.  相似文献   

4.
Unlike conventional sensors that measure the passage of seismic waves at a single position, distributed vibration sensing systems, also known as distributed acoustic sensing systems, detect the passage of seismic waves by averaging a measurement of strain over a section of fibre‐optic cable. Distributed vibration sensing systems work by transmitting pulses of light down the fibre and measuring the phase of the Rayleigh backscatter. At random positions along the fibre, however, fading occurs; this is where the amplitude of the backscattered signal is very small due to cancellation of the scattered electric fields, resulting in anomalously noisy traces in a common source gather. This paper addresses the problem of fading in a particular form of distributed vibration sensors: a new optical arrangement of the instrumentation is described that allows the measurement to be carried out quasi‐simultaneously at multiple optical interrogation frequencies. The interrogation frequencies are chosen to be sufficiently different that their fading properties are distinct and the diversity thus obtained is used to aggregate the data obtained to substantially reduce the noise caused by fading. As well as reducing the effects of fading, the aggregation of the independent results can also help to reduce the overall noise of the measurement and improve the linearity of the distributed vibration sensing system.  相似文献   

5.
Distributed vibration sensing, also known as distributed acoustic sensing, is a relatively new method for recording vertical seismic profile data using a fibre optic cable as the sensor. The signal obtained from such systems is a distributed measurement over a length of fibre referred to as the gauge length. In this paper, we show that gauge length selection is one of the most important acquisition parameters for a distributed vibration sensing survey. If the gauge length is too small, then the signal‐to‐noise ratio will be poor. If the gauge length is too large, resolution will be reduced and the shape of the wavelet will be distorted. The optimum gauge length, as derived here, is a function of the velocity and frequencies of the seismic waves being measured. If these attributes vary considerably over the depth of a survey, then the use of different gauge lengths is recommended. The significant increases in data quality resulting from the use of multiple gauge length values are demonstrated using field data.  相似文献   

6.
Wireline logs and vertical seismic profile data were acquired in two boreholes intersecting the main mineralized zone at the Cu–Au New Afton porphyry deposit, Canada, with the objectives of imaging lithological contacts, fault zones that may have acted as conduits that channelled the mineralization, and alteration zones. Log data provide physical rock properties for the main lithologies and alteration zones. Calliper logs reveal many faults and caved-in zones generally indicating rocks with low integrity at the borehole wall. The preponderance of these zones, as indicated by the logs, suggests that their response may dominate the seismic-reflection wavefield. Outside fault zones, compressional and shear-wave velocities exhibit significant variability due to porosity, the heterogeneity of volcanic fragmental rocks and alteration. Distributed acoustic sensing was used to acquire vertical seismic profiling data in the two boreholes surveyed with wireline logs. Straight and helically wound fibre-optic cables housed standard fibres and a fibre engineered to increase the intensity of backscattering at the distributed acoustic sensing interrogator. Standard and engineered optical fibres placed in the two boreholes were daisy-chained together to form two 5-km-long continuous fibres that were interrogated at once with two interrogators. A new generation of interrogator connected to the engineered fibres provided field data with lower noise level and higher signal-to-noise ratio. These data with higher signal-to-noise ratio from straight fibre-optic cable were processed and used for depth imaging. Depth images benefitted from new migration weights that account for the directional sensitivity of the straight fibre-optic cable and limit the extent of migration artefacts. Migration results show several reflectors with shallow dips to the northwest, some explained by faults intersecting the surveyed boreholes. The main sub-vertical lithological and alteration contacts at New Afton generated downgoing reflections that were not considered in the migration.  相似文献   

7.
In the past decade, rapid advances in distributed optical fibre sensing technologies have made it possible to record various geophysical data (e.g. strain, temperature and pressure) continuously in both time and space along the fibre, providing an unprecedented quantity and spatial density of data compared to traditional geophysical measurements as well as reducing data acquisition cost. To date, no distributed fibre-based electromagnetic field sensing system has been implemented although electromagnetic sensing could have a broad range of applications to geophysical imaging and monitoring in borehole environments. The goal of this paper is to provide a theoretical feasibility study regarding the design and use of an electromagnetic sensing optical fibre for geophysical applications. First, we present the sensitivity analysis of a ‘hypothetical’ optical fibre coated with polyvinylidene fluoride, a polymer that provides relatively high piezoelectric properties, yet unlike ceramics, is flexible. Using a two-dimensional electromagnetic modelling algorithm, we simulate the earth electric-field-to-fibre-strain transfer function and estimate the theoretical sensitivity of the optical fibre to electric fields. Given the state-of-the-art distributed acoustic sensing strain sensitivities in the picometres strain range, our numerical modelling analysis suggests that a perfectly coupled polyvinylidene fluoride–coated optical fibre can measure electric field values in the mV/m to V/m amplitude range. We then apply a cylindrically symmetric modelling algorithm to simulate numerical models demonstrating the applicability of such a fibre in an oilfield environment. Scenarios investigated employ an electric field source and suggest that the measurements can be used to distinguish the oil versus water ratio with a fibre mounted inside a producing steel cased oil well as well as distinguishing between brine and hydrocarbon filled reservoir zones with a fibre located outside of the casing.  相似文献   

8.
In the past few years, distributed acoustic sensing has gained great interest in geophysics. This acquisition technology offers immense improvement in terms of efficiency when compared with current geophysical acquisition methods. However, the fundamentals of the measurement are still not fully understood because direct comparisons of fibre data with conventional geophysical sensors are difficult during field tests. We present downscaled laboratory experiments that enabled us to characterise the relationship between the signals recorded by conventional seismic point receivers and by distributed fibre optic sensors. Interrogation of the distributed optical fibre sensor was performed with a Michelson interferometer because this system is suited to compact test configurations, and it requires only a very simple data processing workflow for extracting the signal outputs. We show acoustic data that were recorded simultaneously by both the fibre optical interferometer and conventional three‐component accelerometers, thus enabling the comparison of sensor performance. We present results focused on the directionality of fibre measurements, on the amplitude variation with angle of incidence, and on the transfer function that allows accelerometer signals to be transformed into optical fibre signals. We conclude that the optical fibre response matches with the array of the displacement differences of the inline accelerometers deployed along the fibre length. Moreover, we also analysed the influence of various types of coupling and fibre cable coating on the signal responses, emphasising the importance of these parameters for field seismic acquisitions when using the distributed fibre optic technology.  相似文献   

9.
Distributed acoustic sensing is a novel technology for seismic acquisition. In this technology, strain changes induced by seismic waves impinging on an optical fibre are monitored. Due to the fact that glass is relatively rigid, straight glass fibres are not sensitive to broadside waves. We suggest using distributed acoustic sensing systems with fibres helically wound around cables. One increases the fibre sensitivity to broadside waves by decreasing the fibre wrapping angle (the angle between the fibre axis and the plane normal to the cable axis). The optimal wrapping angle is chosen to minimize the impact of Rayleigh waves on the signal measured. This angle depends on the cable Poisson ratio, and it is approximately equal to 30° for cables composed of plastic. For reliable detection of seismic waves, one needs a good mechanical contact between the cable and the surrounding medium. On the other hand, the sensitivity of distributed acoustic sensing systems to primary waves can be significantly reduced if the cable is placed in a cemented borehole.  相似文献   

10.
Distributed acoustic sensing uses an optical fibre together with an interrogator unit to perform strain measurements. The usage of distributed acoustic sensing in geophysics is attractive due to its dense spatial sampling and low operation cost if the optical fibre is freely accessible. In the borehole environment, optical fibres for distributed acoustic sensing are often readily available as a part of other sensing tools, such as for temperature and pressure. Although the distributed acoustic sensing system promises great potential for reservoir monitoring and surface seismic acquisition, the single axial strain measurement of distributed acoustic sensing along the fibre is inadequate to fully characterise the different wave modes, thus making reservoir characterisation challenging. We propose an acquisition system using five equally spaced helical optical fibres and a straight optical fibre to obtain six different strain projections. This system allows us to reconstruct all components of the 3D strain tensor at any location along the fibre. Analysing the condition number associated with the geometry of the optical fibre, we can systematically search for the optimum design parameters for our configuration. Numerical examples demonstrate the effectiveness of our proposed method to successful reconstruction of the full strain tensor from elastic wavefields of arbitrary complexity.  相似文献   

11.
Water exchange across the sediment–water interface of streams impresses a characteristic thermal pattern at the interface. The use of fibre optic distributed temperature sensing at the sediment–water interface in a small sand‐bed stream identifies such temperature patterns. Groundwater and interflow can be differentiated based on the temporal evolution of temperature patterns. Additionally, sudden temperature changes at the sediment–water interface observed during the transit of floods enable spatial identification of local up and downwelling. Electromagnetic induction geophysics can detect subsurface texture structures that support groundwater–surface water exchange. Our results show that areas of permanent temperature anomalies observed with fibre optic distributed temperature sensing match areas of comparatively homogeneous electrical conductivity. This indicates groundwater discharge and enables differentiating groundwater discharge from interflow and local downwelling.  相似文献   

12.
Nowadays, full-waveform inversion, based on fitting the measured surface data with modelled data, has become the preferred approach to recover detailed physical parameters from the subsurface. However, its application is computationally expensive for large inversion domains. Furthermore, when the subsurface has a complex geological setting, the inversion process requires an appropriate pre-conditioning scheme to retrieve the medium parameters for the desired target area in a reliable manner. One way of dealing with both aspects is by waveform inversion schemes in a target-oriented fashion. Therefore, we propose a prospective application of the convolution-type representation for the acoustic wavefield in the frequency–space domain formulated as a target-oriented waveform inversion method. Our approach aims at matching the observed and modelled upgoing wavefields at a target depth level in the subsurface, where the seismic wavefields, generated by sources distributed above this level, are available. The forward modelling is performed by combining the convolution-type representation for the acoustic wavefield with solving the two-way acoustic wave-equation in the frequency–space domain for the target area. We evaluate the effectiveness of our inversion method by comparing it with the full-domain full-waveform inversion process through some numerical examples using synthetic data from a horizontal well acquisition geometry, where the sources are located at the surface and the receivers are located along a horizontal well at the target level. Our proposed inversion method requires less computational effort and, for this particular acquisition, it has proven to provide more accurate estimates of the target zone below a complex overburden compared to both full-domain full-waveform inversion process and local full-waveform inversion after applying interferometry by multidimensional deconvolution to get local-impulse responses.  相似文献   

13.
Distributed acoustic sensing is a growing technology that enables affordable downhole recording of strain wavefields from microseismic events with spatial sampling down to ∼1 m. Exploiting this high spatial information density motivates different detection approaches than typically used for downhole geophones. A new machine learning method using convolutional neural networks is described that operates on the full strain wavefield. The method is tested using data recorded in a horizontal observation well during hydraulic fracturing in the Eagle Ford Shale, Texas, and the results are compared to a surface geophone array that simultaneously recorded microseismic activity. The neural network was trained using synthetic microseismic events injected into real ambient noise, and it was applied to detect events in the remaining data. There were 535 detections found and no false positives. In general, the signal-to-noise ratio of events recorded by distributed acoustic sensing was lower than the surface array and 368 of 933 surface array events were found. Despite this, 167 new events were found in distributed acoustic sensing data that had no detected counterpart in the surface array. These differences can be attributed to the different detection threshold that depends on both magnitude and distance to the optical fibre. As distributed acoustic sensing data quality continues to improve, neural networks offer many advantages for automated, real-time microseismic event detection, including low computational cost, minimal data pre-processing, low false trigger rates and continuous performance improvement as more training data are acquired.  相似文献   

14.
以多分量地震观测为基础,联合纵波和转换横波数据能更有效地估计地下介质的弹性和物性参数,提升地质构造成像与油气储层描述的精度.在海底多分量地震数据处理过程中,观测记录的上-下行波分解和P/S波分离可压制水层鸣震以及P与S波之间的串扰,对偏移成像和纵横波速度建模至关重要.但受海底环境、仪器与观测因素共同影响,许多海底多分量地震资料都无法基于现有的海底波场分离方法与流程取得合理的结果.本文以海底声波场与弹性波场分离基本原理为基础,通过对方法流程的修正,摆脱常规流程对中小偏移距直达波信号的依赖性.借助模拟数据实验讨论了波场分离对海底介质参数、噪声的敏感性.结合东海YQ探区海底多分量地震资料上-下行P/S波分离及其叠前深度偏移处理,验证了本文方法流程的可行性.  相似文献   

15.
Paleokarst systems are one of the major factors resulting in carbonate reservoir heterogeneity and compartmentalization. Nevertheless, few effective workflows have been proposed to map the 3D distribution of such systems. We describe a detailed seismic characterization approach integrating core, well log and rock physics analysis, to reveal a complex subsurface paleokarst system in the San Andres Formation, Permian basin, West Texas. In the area of high volume production, the collapsed paleokarst system is characterized by irregularly developed crackle and fracture breccias, mosaic breccias and cave fillings in the Upper San Andres Formation, which are delineated using seismic acoustic impedance. Along the transition from platform to basin, the paleokarst system is marked by a linear collapse including sags and small vertical faults that are recognizable in seismic imaging. Production data indicates that tight paleokarst zones cause reservoir compartmentalization and influence fluid communication between wells. The complex paleokarst system development is explained using a carbonate platform hydrological model, an outcrop analogue similar to modern marine hydrological environments within carbonate islands. Our method of model development for complex subsurface paleokarst systems may be applicable to other paleoenvironments.  相似文献   

16.
A new method was developed for analysing and delineating streambed water fluxes, flow conditions and hydraulic properties using coiled fibre‐optic distributed temperature sensing or closely spaced discrete temperature sensors. This method allows for a thorough treatment of the spatial information embedded in temperature data by creating a matrix visualization of all possible sensor pairs. Application of the method to a 5‐day field dataset reveals the complexity of shallow streambed thermal regimes. To understand how velocity estimates are affected by violations of assumptions of one‐dimensional, saturated, homogeneous flow and to aid in the interpretation of field observations, the method was also applied to temperature data generated by numerical models of common field conditions: horizontal layering, presence of lateral flow and variable streambed saturation. The results show that each condition creates a distinct signature visible in the triangular matrices. The matrices are used to perform a comparison of the behaviour of one‐dimensional analytical heat‐tracing models. The results show that the amplitude ratio‐based method of velocity calculation leads to the most reliable estimates. The minimum sensor spacing required to obtain reliable velocity estimates with discrete sensors is also investigated using field data. The developed method will aid future heat‐tracing studies by providing a technique for visualizing and comparing results from fibre‐optic distributed temperature sensing installations and testing the robustness of analytical heat‐tracing models. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

17.
This paper deals with the design, acquisition and processing of vertical seismic profiling data collected in 2016 at the directional Thônex-01 geothermal well, drilled in 1993 in the Geneva Canton (Switzerland). The aim of the study was to obtain additional information from existing-abandoned well for downhole geophysical characterization of potential geothermal reservoirs in the Geneva area. The main results obtained by this study allowed an improved subsurface image by multi-offset acquisitions near and around the deviated well. Specifically we were able to (1) improve the velocity model of the Geneva Basin, which, at present, is only constrained by one unique deep exploration well, located at the south-west of the basin, far away from the study area; (2) image the transition between the Tertiary Molasse siliciclastic sediments and the Mesozoic carbonates; (3) define an acquisition strategy for future vertical seismic profiling surveys in support of the geothermal exploration campaigns in the area. This study has demonstrated the value of vertical seismic profiling method for the refinement of the subsurface geology at local scale, and its usefulness to assist the planning of second well associated with geothermal doublets.  相似文献   

18.
Distributed acoustic sensing (DAS) is one recently developed seismic acquisition technique that is based on fiber-optic sensing. DAS provides dense spatial spacing that is useful to image shallow structure with surface waves. To test the feasibility of DAS in shallow structure imaging, the PoroTomo team conducted a DAS experiment with the vibroseis truck T-Rex in Brady’s Hot Springs, Nevada, USA. The Rayleigh waves excited by the vertical mode of the vibroseis truck were analyzed with the Multichannel Analysis of Surface Waves (MASW) method. Phase velocities between 5 and 20 Hz were successfully extracted for one segment of cable and were employed to build a shear-wave velocity model for the top 50 meters. The dispersion curves obtained with DAS agree well with the ones extracted from co-located geophones data and from the passive source Noise Correlation Functions (NCF). Comparing to the co-located geophone array, the higher sensor density that DAS arrays provides help reducing aliasing in dispersion analysis, and separating different surface wave modes. This study demonstrates the feasibility and advantage of DAS in imaging shallow structure with surface waves.  相似文献   

19.
At the CO2CRC Otway geosequestration site, the abundance of borehole seismic and logging data provides a unique opportunity to compare techniques of Q (measure of attenuation) estimation and validate their reliability. Specifically, we test conventional time-domain amplitude decay and spectral-domain centroid frequency shift methods versus the 1D waveform inversion constrained by well logs on a set of zero-offset vertical seismic profiles. The amplitude decay and centroid frequency shift methods of Q estimation assume that a seismic pulse propagates in a homogeneous medium and ignore the interference of the propagating wave with short-period multiples. The waveform inversion explicitly models multiple scattering and interference on a stack of thin layers using high-resolution data from sonic and density logs. This allows for stable Q estimation in small depth windows (in this study, 150 m), and separation of the frequency-dependent layer-induced scattering from intrinsic absorption. Besides, the inversion takes into account band-limited nature of seismic data, and thus, it is less dependent on the operating frequency bandwidth than on the other methods. However, all considered methods of Q estimation are unreliable in the intervals where subsurface significantly deviates from 1D geometry. At the Otway site, the attenuation estimates are distorted by sub-vertical faults close to the boreholes. Analysis of repeated vertical seismic profiles reveals that 15 kt injection of the CO2-rich fluid into a thin saline aquifer at 1.5 km depth does not induce detectable absorption of P-waves at generated frequencies 5–150 Hz, most likely because the CO2 plume in the monitoring well is thin, <15 m. At the Otway research site, strong attenuation Q ≈ 30–50 is observed only in shaly formations (Skull Creek Mudstone, Belfast Mudstone). Layer-induced scattering attenuation is negligible except for a few intervals, namely 500–650 m from the surface, and near the injection interval, at around 1400–1550 m, where Qscat ≈ 50–65.  相似文献   

20.
近年来发展的新型地震观测系统--分布式光纤声波传感器(DAS,Distributed Acoustic Sensing)可以实现低成本高密度观测,有望提高浅层结构成像的精度以及分辨率.最近国内研发了一系列具有自主知识产权的DAS设备,为验证国产设备在浅层结构研究中的可行性以及应用效果,2018年7月我们开展了一次DAS观测实验.实验采集了50kg落锤震源激发的地震信号,并采用多道面波分析方法提取了8~20Hz频段的主动源Rayleigh波相速度频散曲线,得到了实验区浅层30m的S波速度结构.获得的主动源面波频散曲线与共址检波器的结果吻合,也与背景噪声提取的结果具有较好的一致性,表明国产设备的可靠性和DAS在浅层结构主动源面波成像研究中的可行性.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号