共查询到20条相似文献，搜索用时 15 毫秒
1.
2.
近地表沉积层的S速度结构是强地面震动模拟和地震灾害估计的重要参数,尤其是浅部的S波速度结构在工程上具有重要的应用意义．目前大部分资料来源于工程钻孔或工程地震探测,很少有地震波频率范围内的S波速度结构,或者深度达数百米的S波速度结构．通过对天然地震的井下摆波形记录的分析,提供了一种测量地震波频率范围深达数百米的S波速度的有效方法．收集了首都圈地区44个井下摆的近震记录,利用广义射线方法确认了直达S波及其在地表的反射波震相,并通过测量不同台站上两个震相的到时差,获得了首都圈地区浅层100——500m 深度范围的S波速度结构．研究发现,浅部100m 的平均S波速度低于300m/s．当深度增加到500m 时S波速增加到800m/s,平均速度梯度为0.8 （m/s）/m．研究结果表明,井下摆地震记录波形是研究沉积盆地浅层S波结构的重要资料,将为沉积盆地的强地面震动模拟提供重要基础参数． 相似文献
3.
The theoretical behaviour of guided waves in cross-hole seismic surveys is examined with dispersion curves and synthetic seismograms. The modelling suggests, and field observations confirm, that the dominant energy in many cross-hole seismic surveys propagates as guided waves, as well as body waves, with the energy tied to an interface, or combination of interfaces, whenever there are interfaces with significant velocity contrasts continuous between the wells. The dispersion and waveforms of such modal solutions carry detailed information about the internal structure, particularly the stress-aligned structure of fluid-filled inclusions in the immediate neighbourhood of the waveguide. Since the information content can be controlled to some extent by the choice of frequency and source type and the level of source and receiver in the two wells, such guided waves in cross-hole surveys may be important for monitoring changes in nearly horizontal reservoirs during hydrocarbon production processes. Initially, we investigate the basic properties of propagation in isotropic strata, and then examine the behaviour of guided waves in the stress-aligned fluid-filled inclusions. 相似文献
4.
For land seismic surveys, the surface waves are the dominant noises that mask the effective signals on seismograms. The conventional methods isolate surface waves from the effective signals by the differences in frequencies or apparent velocities, but may not perform well when these differences are not obvious. Since the original seismic interferometry can only predict inter-receiver surface waves, we propose the use of super-virtual interferometry (SVI), which is a totally data-driven method, to predict shot-to-receiver surface waves, since this method relieves the limitation that a real shot should collocate with one of the receivers for adaptive subtraction. We further develop the adaptive weighted SVI (AWSVI) to improve the prediction of dispersive surface waves, which may be generated from heterogeneous media at the near surface. Numerical examples demonstrate the effectiveness of AWSVI to predict dispersive surface waves and its applicability to the complex near surface. The application of AWSVI on the field data from a land survey in the east of China improves the suppression of the residual surface waves compared to the conventional methods. 相似文献
5.
F. AMINZADEH 《Geophysical Prospecting》1989,37(8):893-906
Data from offshore Norway is used to study applications of elastic VSP modelling in detecting shear waves and observing the effects of successive mode conversion in field-recorded VSP data. The shear-wave velocities and densities from log data are used in conjunction with compressional wave velocities determined from surface seismic and log data in the VSP modelling. The time domain non-normal incidence elastic VSP modelling technique of Aminzadeh and Mendel is used as the modelling algorithm. Two surface seismograms are computed first. One is the vertical component and the other is the horizontal component for plane waves that have specified incident angles. A downward continuation method is then applied to generate seismograms at different depth points. The collection of these seismograms constitutes non-normal incidence VSPs. Both vertical and horizontal components of VSP data can be obtained by this procedure. In this paper non-normal incidence VSPs are generated for a 12.5° incident plane wave. The modelling results of layered earth systems of thin layers and thick layers are both compared with field data, and the effect of mode conversions in thin layers is observed. Several events in the field data can be explained by this elastic VSP modelling. Comparison of the model data and field data enabled a probable tube wave or out-of-plane event to be identified, the removal of which significantly improved the final VSP section. This study also shows how the VSP data helped the interpretation of the surface 3D data. 相似文献
6.
2019年3月21日江苏盐城响水化工厂发生爆炸,造成了巨大的人员伤亡和财产损失.人们很关心这次爆炸的规模以及它相当于多大当量的炸药爆炸.随着观测资料的增多与地震学方法的发展,利用地震学方法估算爆炸当量成为可能.本文收集了广岛核爆事件、美国化学爆炸试验、长白山人工震源勘探、朝鲜六次核试爆资料和前人研究成果,讨论了爆炸当量与爆炸所产生地震震级的关系,计算了爆炸能量转换地震波能量的比例.当某次爆炸发生时,如果其产生的地震事件被台站记录到,我们可以估算地震波的能量.进而根据地震波能量在爆炸总能量中的比例,估算爆炸事件释放的能量.本研究估计江苏响水爆炸事故所释放炸药量约为2.8~8.5tTNT炸药. 相似文献
7.
A modified reverse-time migration algorithm for offset vertical seismic profiling data is proposed. This algorithm performs depth imaging of target areas in the borehole vicinity without taking into account the overburden. Originally recorded seismograms are used; reliable results can be obtained using only the velocity profile obtained along the well. The downgoing wavefield emitted from a surface source is approximated in the target area using the transmitted P-wave, recorded by the receivers deployed in the well. This is achieved through a reverse-time extrapolation of the direct transmitted P-wave into the target area after its separation in offset vertical seismic profiling seismograms generated using a finite-difference scheme for the solution of the scalar wave equation.
The proposed approach produces 'kinematically' reliable images from reflected PP- and PS-waves and, furthermore, can be applied as a salt proximity tool for salt body flank imaging based on the transmitted PS-waves. Our experiments on synthetic data demonstrate that the modified reverse-time migration provides reliable depth images based on offset vertical seismic profiling data even if only the velocity profile obtained along the borehole is used. 相似文献
The proposed approach produces 'kinematically' reliable images from reflected PP- and PS-waves and, furthermore, can be applied as a salt proximity tool for salt body flank imaging based on the transmitted PS-waves. Our experiments on synthetic data demonstrate that the modified reverse-time migration provides reliable depth images based on offset vertical seismic profiling data even if only the velocity profile obtained along the borehole is used. 相似文献
8.
Acquisition and processing of pure and converted shear waves generated by compressional wave sources
The most common source of seismic energy onshore is a vertical impact on the earth's surface or an explosion at some depth in a borehole. These sources produce mainly compressional waves. Here it is shown how these sources can be used to generate shear waves either by conversion in the depth or in the immediate vicinity of the source itself. The use of theoretical seismograms can help to identify the individual onsets especially on the horizontal components of the earth's movement. Due to the more complex raypath, converted waves need a special data processing. The spectral behaviour can be improved by spectral balancing followed by a spiking deconvolution. As the CDP-concept is no longer applicable for converted PS-waves a special sorting for a common conversion point (CCP) is applied. The identification and analysis of the individual waves can be simplified by a detailed polarization analysis taking into account the full dynamic behaviour of the observed waves. Prestack depthmigration of converted PS waves allows to deduce additional information on the material properties of reflecting horizons. The depth-migration of individual shot gathers is achieved in the frequency-space domain. Thus the kinematic and dynamic aspects of these secondary waves is a valuable tool for a better understanding of the elastic behaviour of the subsurface. 相似文献
9.
Analytical expressions for the borehole seismic signatures excited by an explosive source buried in an elastic half‐space 
下载免费PDF全文
下载免费PDF全文 Andrei M. Ionov 《Geophysical Prospecting》2018,66(Z1):161-174
Borehole guided waves that are excited by explosive sources outside of the borehole are important for interpreting borehole seismic surveys and for rock property inversion workflows. Borehole seismograms are typically modelled using numerical methods of wave propagation. In order to benchmark such numerical algorithms and partially to interpret the results of modelling, an analytical methodology is presented here to compute synthetic seismograms. The specific setup is a wavefield emanating from a monopole point source embedded within a homogeneous elastic medium that interacts with a fluid‐filled borehole and a free surface. The methodology assumes that the wavelength of the seismic signal is much larger than the borehole radius. In this paper, it is supposed that there is no poroelastic coupling between the formation and the borehole. The total wavefield solution consists of P, PP, and PS body waves; the surface Rayleigh wave; and the low‐frequency guided Stoneley wave (often referred as the tube wave) within the borehole. In its turn, the tube wave consists of the partial responses generated by the incident P‐wave and the reflected PP and PS body waves at the borehole mouth and by the Rayleigh wave, as well as the Stoneley wave eigenmode. The Mach tube wave, which is a conic tube wave, additionally appears in the Mach cone in a slow formation with the tube‐wave velocity greater than the shear one. The conditions of appearance of the Mach wave in a slow formation are formulated. It is shown that the amplitude of the Mach tube wave strongly depends on Poisson's ratio of the slow surrounding formation. The amplitude of the Mach tube wave exponentially decreases when the source depth grows for weakly compressible elastic media with Poisson's ratio close to 0.5 (i.e., saturated clays and saturated clay soils). Asymptotic expressions are also provided to compute the wavefield amplitudes for different combinations of source depth and source‐well offset. These expressions allow an approximate solution of the wavefield to be computed much faster (within several seconds) than directly computing the implicit integrals arising from the analytical formulation. 相似文献
10.
J. FERTIG 《Geophysical Prospecting》1984,32(1):1-17
The most common source of seismic energy is an explosion at some depth in a borehole. The radiated waves are reflected not only at the subsurface layers but also at the free surface. The earth's surface acts as a generator of both P- and S-waves. If the source depth is much less than the dominant wavelength the reflected waves resemble closely the waves generated by a single force. Theoretical seismograms were computed with different methods to look for the relevance of the surface-reflected waves. The numerical experiments show reflected shear waves even for small shotpoint—receiver distances. Due to their polarization these waves can be detected most easily on in-line horizontal geophones. The existence of these waves was examined during a conventional survey in Northern Germany. Conventional data analysis shows a large variability in the νp/νs ratio. The method used here produced a shear-wave section with a rather good signal-to-noise ratio down to 4 s S-wave reflection time. 相似文献
11.
高铁列车运行过程中绝大部分时间都是行驶在高架桥上的,高铁列车经过桥梁时,通过与大地耦合的桥墩激发地震波发震过程和平地不完全一样.本文探索高铁列车行驶经过高架桥桥墩,通过桥墩对地下介质激发地震波的机理及过程.为了便于理论分析,文中将高铁列车简化为在高架桥上沿一个方向运动的移动线源,通过每节车厢前后组轮对,对每一个桥墩施加力的作用,而桥墩插入地面几十米深至围岩,与表层土壤和深层围岩双重耦合,由此给出高铁列车通过桥墩激发地震波的震源时间函数.同时,基于广义连续介质力学框架下的修正偶应力理论,推导包含介质特征尺度的弹性波动方程,并应用此弹性波动方程以及构建的高铁震源时间函数,采用优化的交错网格有限差分算法,实现数值模拟,将合成的地震记录与实际地震记录对比分析,其结论将为进一步的基于高铁震源的成像和反演研究提供理论依据. 相似文献
12.
《中国科学:地球科学(英文版)》2017,(10)
The active sources generate seismic waves transmitting appropriate through the deep is underground key and can be used to image Abstract high-resolution subsurface structures.Therefore,an seismic source the factor to active source exploration.In order to study the structure of continental crust and its temporal variations,we selected an artificial seismic source generated from releasing air bubbles in water(airgun source hereinafter)out of a variety and of artificial sources like the is explosion,new electronic sparkers,source hammering,eccentric proven vibration,be heavy-duty train vibration,vibroseis etc.Airgun Three source Fixed a type of artificial that have been to environmentally friendly,safe,and highly efficient.Airgun western Signal China Transmission and Stations(FASTS)have been for built a few years ago in Yunnan,Xinjiang,and Gansu provinces in have been continuously them running several years.Seismic waves generated away by the the airgun sources are highly seismic reproducible waves and stacking in of can produce can good seismograms on 1300 stations km far from source,for instance,an produced Xinjiang FASTS be well about recorded 60 nearly away after 5000 stacking,China covering area of 6 million km2 and penetrating down to of a depth of km.Establishing about 10 FASTSs in would enable long-term illuminate continuous subsurface underground structures,monitoring can all 9.6 million km2 of land area.Treating from airgun sky active sources as lanterns to we achieve the situation with"Beidou surveys the and lantern illuminates underground". 相似文献
13.
目前人们利用4种基本的地震波现象研究地震各向异性,如横波双折射、面波散射、与传播方向有关的走时异常和PS转换波震相.本文利用面波散射产生的Quasi-Love（QL）波研究青藏高原上地幔顶部的各向异性结构特征.首先利用中国地震台网昌都（CAD）台记录的地震波形资料识别出产生QL波的路径,并利用合成地震记录和垂直偏振极性分析证实所观测到的为QL波,而不是高阶振型的Rayleigh波或其他体波震相;然后由Rayleigh波、Love波和QL波的群速度估算了各向异性结构横向变化的转换点;不同周期时,转换点的位置不同,这种频率依赖性还需要进一步的模拟研究.Love波向Rayleigh波耦合（产生QL波）的转换点位置揭示了青藏高原面波方位各向异性变化特征,并以南北向构造带的东西分段性、上地幔流引起的地球内力诱导岩石形变解释了青藏高原各向异性的东西向差异性. 相似文献
14.
Zehua Qiu Shunliang Chi Zhenming Wang Seth Carpenter Lei Tang Yanping Guo Guang Yang 《地震科学（英文版）》2015,28(3):209-214
At a sampling rate of 100 samples per second,the YRY-4 four-gauge borehole strainmeters(FGBS) are capable of recording transient strains caused by seismic waves such as P and S waves or strain seismograms. At such a high sampling rate, data from the YRY-4 strainmeters demonstrate fairly satisfactory self-consistency. The strain tensor seismograms demonstrate the senses of motion of P waves, that is, the type of seismic wave travels in the direction of the maximum normal strain change. The observed strain patterns of S waves significantly differ from those of P waves and should contain information about the source mechanism. Spectrum analysis shows that the strain seismograms are consistent with conventional broadband seismograms from the same site. 相似文献
15.
In seismic exploration for coal data resolution is a fundamental problem. Modeling helps to understand those details of the geology that can be interpreted from the seismic image. For single seam exploration, the vertical resolution of a seismic section is defined by the bandwidth of the signals. If there are several seams, each seam acts as a high-pass filter for reflections and as a low-pass filter for transmitted waves. Synthetic seismograms show that reflections from deep seams have a low frequency content. Within a layered sequence of coal seams, many multiples are generated which disturb later primary reflections. The ratio of primaries to multiples depends on the frequency content of the seismic data and on the number of overlying seams. The multiple problem is more severe with high frequencies. Primary reflections from deep coal seams within a sequence can be detected only if low-frequency signals are used. However, the use of low-frequency signals reduces the resolution of the deeper data. 相似文献
16.
Three-dimensional kinematic depth migration of converted waves: application to the 2002 Molise aftershock sequence (southern Italy) 总被引：1，自引：0，他引：1
Diana Latorre Pasquale De Gori Claudio Chiarabba Alessandro Amato Jean Virieux Tony Monfret 《Geophysical Prospecting》2008,56(4):587-600
Migration techniques, currently used in seismic exploration, are still scarcely applied in earthquake seismology due to the poor source knowledge and sparse, irregular acquisition geometries. At the crustal scale, classical seismological studies often perform inversions based on the arrival time of primary phases (P- and S-waves) but seldom exploit other information included in seismic records. Here we show how migration techniques can be adapted to earthquake seismology for converted wave analysis. As an example, we used data recorded by a dense local seismic network during the 2002 Molise aftershock sequence. In October and November 2002, two moderate magnitude earthquakes struck the Molise region (southern Italy), followed by an aftershock sequence lasting for about one month. Local earthquake tomography has provided earthquake hypocenter locations and three-dimensional models of P and S velocity fields. Strong secondary signals have been detected between first-arrivals of P- and S-waves and identified as SP transmitted waves. In order to analyse these waves, we apply a prestack depth migration scheme based on the Kirchhoff summation technique. Since source parameters are unknown, seismograms are equalized and only kinematic aspects of the migration process are considered. Converted wave traveltimes are calculated in the three-dimensional (3D) tomographic models using a finite-difference eikonal solver and back ray tracing. In the migrated images, the area of dominant energy conversion corresponds to a strong seismic horizon that we interpreted as the top of the Apulia Carbonate Platform and whose geometry and position at depth is consistent with current structural models from existing commercial seismic profiles, gravimetric and well data. 相似文献
17.
H. C. HARDEE 《Geophysical Prospecting》1983,31(1):57-71
Downhole periodic seismic sources have been proposed as a means for studying fluid zones in hydrothermal/magma systems encountered in deep scientific holes drilled as part of the Continental Scientific Drilling Program. Scientific measurements in these holes will require the use of downhole, nondestructive, high resolution, seismic tools. Downhole periodic seismic sources tested in a shallow geothermal zone showed that a pneumatic oscillator could effectively generate downhole low-frequency (10–100 Hz) seismic waves and that these waves could effectively penetrate a highly fractured formation. An improved version of these downhole sources, capable of swept-frequency operation, is currently under development. This type of downhole seismic source has applications in crustal studies and in the evaluation of petroleum, groundwater and geothermal reservoirs. 相似文献
18.
Using an airgun array in a land reservoir as the seismic source for seismotectonic studies in northern China: experiments and preliminary results 总被引：15，自引：0，他引：15
This paper reports the field setup and preliminary results of experiments utilizing an airgun array in a reservoir in north China for a seismotectonic study. Commonly used in offshore petroleum resource exploration, the airgun source was found to be more useful than a traditional explosive source for large‐scale and long offset land seismic surveys. The airgun array, formed by four 1,500 in3 airguns (a total of 6,000 in3 in volume) was placed at a depth of 6–9 m into the reservoir to generate the pressure impulse. No direct evidence was found that the airgun source adversely affected the fish in the reservoir. The peak ground acceleration recorded on the top of the reservoir dam 100 m away was 17.8 gal in the horizontal direction; this is much less than the designed earthquake‐resistance threshold of 125 gal for this dam. The energy for one shot of this airgun array is about 6.68 MJ, equivalent to firing a 1.7 kg explosive. The seismic waves generated by the airgun source were recorded by receivers of the regional seismic networks and a temporary wide‐angle reflection and refraction profile formed by 100 short‐period seismometers with the maximum source‐receiver offset of 206 km. The seismic wave signature at these long‐offset stations is equivalent to that generated by a traditional blast source in a borehole with a 1,000–2,000 kg explosive. Preliminary results showed clear seismic phases from refractions from the multi‐layer crustal structures in the north China region. Forward modelling using numerical simulation confirms that the seismic arrivals are indeed from lower crustal interfaces. The airgun source is efficient, economical, environmentally friendly and suitable for being used in urbanized areas. It has many advantages over an explosive source for seismotectonic studies such as the high repeatability that is supreme for stacking to improve signal qualities. The disadvantage is that the source is limited to existing lakes or reservoirs, which may restrict experimental geometry. 相似文献
19.
提出一种自适应协方差的时频域极化滤波方法。该方法在广义S变换时频方法的基础上,构造时频域自适应协方差矩阵,通过特征分析计算时频域瞬时极化参数,设计极化滤波器,实现多分量地震极化分析和滤波。其优势在于协方差矩阵的分析时窗的长度由多分量地震数据的瞬时频率确定,可以自适应于有效信号的周期,在每个时频点计算极化参数不需要进行插值处理;结合时间频率信息,解决在时间域或频率域波形或频率重叠的信号具有明显的直观性。模型数据及实际三分量台站地震数据处理结果表明,该极化滤波方法在台站地震资料分析和处理方面具有很好的直观性和较高的分辨率。 相似文献
20.
We use different interferometry approaches to process the seismic signals generated by a drill‐bit source in one well and recorded by seismic receivers located both in a second borehole and at the surface near the source well. We compare the standard interferometry results, obtained by using the raw drill‐bit data without a pilot signal, with the new interferometry results obtained by using the drill‐bit seismograms correlated with a reference pilot signal. The analysis of the stationary phase shows that the final results have different S/N levels and are affected by the coherent noise in the form of rig arrivals. The interferometry methods are compared by using different deconvolution approaches. The analysis shows that the results agree with the conventional drill‐bit seismograms and that using the reference pilot signal improves the quality of the drill‐bit wavefields redatumed by the interferometry method. 相似文献