共查询到20条相似文献，搜索用时 203 毫秒
1.
Fractured-rock aquifers display spatially and temporally variable hydraulic conductivity generally attributed to variable fracture intensity and connectivity. Empirical evidence suggests fracture aperture and hydraulic conductivity are sensitive to in situ stress. This study investigates the sensitivity of fractured-rock hydraulic conductivity, groundwater flow paths, and advection-dominated transport to variable shear and normal fracture stiffness magnitudes for a range of deviatoric stress states. Fracture aperture and hydraulic conductivity are solved for analytically using empirical hydromechanical coupling equations; groundwater flow paths and ages are then solved for numerically using groundwater flow and advection-dispersion equations in a traditional Toth basin. Results suggest hydraulic conductivity alteration is dominated by fracture normal closure, resulting in decreasing hydraulic conductivity and increasing groundwater age with depth, and decreased depth of long flow paths with decreasing normal stiffness. Shear dilation has minimal effect on hydraulic conductivity alteration for stress states investigated here. Results are interpreted to suggest that fracture normal stiffness influences hydraulic conductivity of hydraulically active fractures and, thus, affects flow and transport in shallow (<1 km) fractured-rock aquifers. It is suggested that observed depth-dependent hydraulic conductivity trends in fractured-rock aquifers throughout the world may be partly a manifestation of hydromechanical phenomena. 相似文献
2.
Analytical and empirical methods used in current engineering practice for estimating inflow rate into a tunnel do not adequately account for the effect of groundwater level drawdown which triggers changes of the flow pattern as well as reductions of the hydraulic head. When there is no reservoir or a large body of water near the tunnel alignment, the groundwater recharge above the tunnel might not be fast enough to avoid a significant excavation-induced water level drawdown. This paper provides analytical methods for estimating groundwater inflow rate taking into account the groundwater table drawdown. The proposed analytical solutions presented here compare well with field observations as well as with results from numerical analysis using distinct element method which can adequately simulate the hydro-mechanically coupled behavior of joints in a rock mass. 相似文献
3.
在偏压情况下对不同埋深的4车道和2车道偏压公路隧道建立其力学模型,研究其松动围岩力学特征。在考虑应力剪胀对隧道围岩的影响后,计算出洞周围岩位移、收敛比。研究结果表明：对于相同的条件,4车道偏压公路隧道的围岩剪切破坏带比2车道更容易与地面贯通;随着剪胀角的递增,围岩位移矢量和隧道拱顶下沉量逐渐减小,拱脚水平位移逐渐增大;大跨度隧道围岩位移受剪胀角的影响比小断面隧道显著。 相似文献
4.
Hydraulic Characteristics of Rough Fractures in Linear Flow under Normal and Shear Load 总被引：19，自引：3，他引：19
Summary
A hydro-mechanical testing system, which is capable of measuring both the flow rates and the normal and shear displacement
of a rock fracture, was built to investigate the hydraulic behaviour of rough tension fractures. Laboratory hydraulic tests
in linear flow were conducted on rough rock fractures, artificially created using a splitter under various normal and shear
loading. Prior to the tests, aperture distributions were determined by measuring the topography of upper and lower fracture
surfaces using a laser profilometer. Experimental variograms of the initial aperture distributions were classified into four
groups of geostatistical model, though the overall experimental variograms could be well fitted to the exponential model.
The permeability of the rough rock fractures decayed exponentially with respect to the normal stress increase up to 5 MPa.
Hydraulic behaviours during monotonic shear loading were significantly affected by the dilation occurring until the shear
stress reached the peak strength. With the further dilation, the permeability of the rough fracture specimens increased more.
However, beyond shear displacement of about 7 to 8 mm, permeability gradually reached a maximum threshold value. The combined
effects of both asperity degradation and gouge production, which prohibited the subsequent enlargement of mean fracture aperture,
mainly caused this phenomenon. Permeability changes during cyclic shear loading showed somewhat irregular variations, especially
after the first shear loading cycle, due to the complex interaction from asperity degradations and production of gouge materials.
The relation between hydraulic and mechanical apertures was analyzed to investigate the valid range of mechanical apertures
to be applied to the cubic law.
Received June 12, 2001; accepted February 26, 2002 Published online September 2, 2002 相似文献
5.
This paper presents an analytical evaluation on the influence of foam conditioning on groundwater inflow at shield tunnel cutting face by the force-equilibrium principle. Three key variables are highlighted, namely, the maximum foam infiltration distance, the critical infiltration distance, and the hydraulic conductivity of foam-conditioned soil or rock fissure. To capture the variation of water level induced by foam injection, a dynamic water-level equation is considered in the force-equilibrium principle. The proposed analytical equations are employed to analyze a water inflow case during shield tunneling in a weathered mylonite fault. The results indicate that the hydraulic conductivity of foam-conditioned mylonite and the infiltration distance decrease with an increase of shear stress of foam fluid. A three-dimensional finite element model is employed to validate the analytical solutions. The comparison between the observed and calculated results confirms that the proposed method can predict groundwater inflow in foam-conditioned soils. 相似文献
6.
The fluid flow in rock fractures during shear processes has been an important issue in rock mechanics and is investigated in this paper using finite element method (FEM), considering evolutions of aperture and transmissivity with shear displacement histories under different normal stress and normal stiffness conditions as measured during laboratory coupled shear-flow tests. The distributions of fracture aperture and its evolution during shearing were calculated from the initial aperture, based on the laser-scanned sample surface roughness results, and shear dilations measured in the laboratory tests. Three normal loading conditions were adopted in the tests: simple normal stress and mixed normal stress and normal stiffness to reflect more realistic in situ conditions. A special algorithm for treatment of the contact areas as zero-aperture elements was used to produce more accurate flow field simulations, which is important for continued simulations of particle transport but often not properly treated in literature. The simulation results agree well with the measured hydraulic apertures and flow rate data obtained from the laboratory tests, showing that complex histories of fracture aperture and tortuous flow fields with changing normal loading conditions and increasing shear displacements. With the new algorithm for contact areas, the tortuous flow fields and channeling effects under normal stress/stiffness conditions during shearing were more realistically captured, which is not possible if traditional techniques by assuming very small aperture values for the contact areas were used. These findings have an important impact on the interpretation of the results of coupled hydro-mechanical experiments of rock fractures, and on more realistic simulations of particle transport processes in fractured rocks. 相似文献
7.
引入并修正了变刚度的连续屈服节理模型,同时考虑应力拉压和压力（化学）溶解对裂隙开度的综合影响,对所建立的双重孔隙-裂隙介质热-水-应力耦合有限元计算程序作了改进。通过一个假定的高放废物地质处置库的数值模拟,就岩体裂隙刚度变化的2种工况,分析了岩体中的温度、裂隙刚度、正应力、孔（裂）隙水压力和地下水流速的变化、分布情况。结果显示：与裂隙刚度是常数时相比,裂隙刚度是法向应力的函数时计算域中温度较低;岩体应力的大小也有一定不同,其分布与裂隙刚度“场”有明显的相似性;并且负孔（裂）隙水压力的绝对值要略小一点,约是常数时的98%。 相似文献
8.
9.
以地下水位线以下的石楼隧道典型三趾马红土围岩段为例,通过现场监测对三趾马红土围岩的体积含水量、孔隙水压力、围岩应力（土压力）、拱顶沉降与水平收敛进行了分析。在此基础上,通过原位大剪试验获得了可靠的围岩抗剪强度参数,并建立了隧道三维有限元数值模型,分别对考虑水-力耦合效应、不考虑水-力耦合效应的三趾马红土围岩变形规律进行了探讨,分析了孔隙水压力随着隧道开挖的变化和三趾马红土围岩位移场、应力场受水-力耦合效应的影响程度,并提出了围岩破坏变形机制。结果表明:（1）实测拱顶下沉大于围岩水平变形,围岩应力可分为增长期（ < 20d）、调整期（20~60d）、稳定期（>60d）3个阶段,且整体应力水平较高,下台阶含水量大于上台阶,孔隙水压力经历了由负变正的过程。（2）现场剪切试验所测围岩的黏聚力为64.0kPa,内摩擦角为27.7°。（3）数值分析表明,隧道开挖后孔隙水压力场变化十分明显,这是由地下水流速场的改变引起的,水力坡降在衬砌面附近最为明显,渗透动水压力导致土体产生一定的渗透变形;考虑水-力耦合后围岩剪应力、最大剪应变、拱顶沉降、水平收敛、底板隆起均较大。（4）受开挖及支护的影响,地下水产生渗流并依次经过拱顶、边墙,最终汇集于隧底;受开挖、地下水渗流的影响,围岩节理裂隙进一步扩张,成为地下水良好的运移通道;围岩的有效应力随着孔隙水压力的减小而增大,围岩的力学强度在土体趋于饱和状态时骤降,反过来,高有效应力、低围岩强度以及贯通性节理裂隙三者共同改变着地下水渗流场的状态。（5）为保障围岩整体稳定性,建议及时排出隧道底部积水并施做仰拱。 相似文献
10.
裂隙的剪胀特性及扩展演化规律对岩体的渗流特性具有重要影响。为揭示裂隙剪胀及扩展演化对岩体渗流的影响,基于残余强度提出了一种能较好描述岩石硬化-软化特性的全剪切本构关系;结合剪切变形与裂隙开度的关系,利用最小势能原理和立方定律,建立了压剪作用下考虑裂隙剪胀特性的渗流应力耦合模型;假定压剪作用下裂隙发生Ⅰ型扩展,提出了伴有翼型裂纹的渗流模型,该模型不仅考虑了岩石的剪胀特性,更反映了裂隙扩展过程渗流的演化规律。对不同裂隙粗糙度的剪切应力-位移曲线进行分析,全剪切本构模型表现出较高的拟合精度。在剪切应力-位移关系基础上,通过剪切渗流试验数据对压剪作用下渗流模型进行验证,结果表明,该模型能较好地描述岩体剪胀阶段渗透性演化规律。利用等效裂隙简化裂隙网络,并通过试验数据进行验证,证实了裂隙扩展过程渗流-应力耦合模型的准确性与适用性。 相似文献
11.
采用UDEC离散单元法中关于裂隙岩体开挖模拟及水力全耦合分析模型,分析裂隙岩体洞室开挖后,因围岩应力与水力耦合作用导致裂隙隙宽变化及渗流变化的过程。为了更直观地了解耦合作用对裂隙岩体渗透特性的影响,以隧洞开挖为例,用开挖后隧洞内总涌水量来表征岩体的渗透特性。利用数值试验的方法,研究了块体边界大小、初始应力比、裂隙隙宽和裂隙夹角对开挖后隧洞内涌水量变化的影响,进而可以看出它们对裂隙岩体渗透性的影响。并得出如下结论：随着块体尺寸和初始应力比的增大,隧洞内总涌水量减少;随初始隙宽的增大涌水量增加并当达到某一固定值时保持不变;隧洞涌水量在θ2/θ1=3.5,其中θ1=30°,即两组节理的夹角为75°处达到最大。 相似文献
12.
节理在固定法向压力刚度（CNS）条件下的剪切过程比较复杂,剪切中由于剪胀的存在使得法向压力增大,而法向压力的增加又限制了剪胀的发生。根据CNS剪切过程中某一瞬时状态下法向压应力大小,以节理在该法向压应力下法向剪胀位移与剪切位移的关系为基础,建立一个楔形物理模型。通过循环迭代求得CNS剪切过程中每一步的法向压应力值,进而得到整个过程的剪切应力值。通过该模型,讨论了节理各参数对CNS剪切过程的影响,结果表明,其剪切应力值受法向压应力刚度与节理法向变形参数共同协调控制（包括单轴压缩变形及剪胀角的磨损）,节理在剪切过程中越不易发生压缩变形,其剪切应力值越大。 相似文献
13.
渗透水压对节理应力-渗流耦合特性的影响试验研究 总被引：1，自引：0，他引：1
为研究渗透水压对节理应力-渗流耦合特性的影响,通过对6组人造节理试件恒定法向载荷和恒定法向刚度的压剪渗流试验,分析了应力和位移、节理水力开度以及透过率随剪切位移的变化趋势,获得了渗透水压对节理岩石应力-渗流耦合特性的影响规律。结果表明：节理试件的剪切应力和位移、水力开度以及透过率都与渗透水压密切相关。剪切应力随渗透水压的增大而减小,法向变形、水力开度和透过率却随渗透水压的增大而增大。在压剪渗流试验过程中,不同渗透压力的节理试件都发生了剪胀效应。研究可为深部岩体工程围岩遇水作用稳定性及渗流灾害控制技术提供科学的理论依据。 相似文献
14.
Van-Manh Nguyen Heinz Konietzky Thomas Frühwirt 《Geotechnical and Geological Engineering》2014,32(4):829-846
A new procedure is presented, which combines big shear box tests on rocks and corresponding numerical simulations with explicit consideration of joint roughness to get deeper insight into the shear behavior of rock joints. The procedure consists of three parts: (1) constant normal load- or CNS-shear box tests with registration of shear- and normal-components of stress and displacements and deduction of basis rock mechanical parameters; (2) high resolution 3D-scanning of joint surface to deduce joint topography; and (3) set-up, run and evaluation of 3-dimensional numerical model with explicit duplication of joint roughness as back-analysis of shear box tests. The numerical back-analysis provides deeper insight into the joint behavior at the micro-scale. Several parameters can be deduced, like micro-slope angle distribution, aperture size distribution, local normal stress distribution and detailed analysis of dilation in relation to shear direction. The potential of the new procedure is illustrated exemplary by shear box tests on slate. 相似文献
15.
A finite volume-based numerical modeling framework using a hierarchical fracture representation (HFR) has been developed to compute flow-induced shear failure. To accurately capture the mechanics near fracture manifolds, discontinuous basis functions are employed which ensure continuity of the displacement gradient across fractures. With these special basis functions, traction and compressive forces on the fracture segment can be calculated without any additional constraints, which is extremely useful for estimating the irreversible displacement along the fracture (slip) based on a constitutive friction law. The method is further extended to include slip-dependent hydraulic aperture change and grid convergent results are obtained. Further, the change in hydraulic aperture is modeled using an asymptotic representation which respects the experimentally observed behavior of pore volume dilation due to shear slip. The model allows the initial rapid increase in hydraulic aperture due to shear slip and asymptotically approaches a finite value after repeated shearing of a fracture segment. This aperture increase is the only feedback for mechanics into the fluid flow for a linear elastic mechanics problem. The same model is also extended to include poroelastic relations between flow and mechanics solver. The grid convergence result in the case of poroelastic flow-mechanics coupling for flow-induced shear failure is also obtained. This proves the robustness of the numerical and analytical modeling of fracture and friction in the extended finite volume method (XFVM) set-up. Finally, a grid convergent result for seismic moment magnitude for single fracture and fracture network with random initial hydraulic and friction properties is also obtained. The b-value, which represents the slope of seismic moment occurrence frequency decay vs seismic moment magnitude, which is approximately constant in a semi-logarithmic plot, is estimated. The numerical method leads to converged b-values for both single fracture and fracture network simulations, as grid and time resolutions are increased. For the resulting linear system, a sequential approach is used, that is, first, the flow and then the mechanics problems are solved. The new modeling framework is very useful to predict seismicity, permeability, and flow evolution in geological reservoirs. This is demonstrated with numerical simulations of enhancing a geothermal system. 相似文献
16.
岩溶地区隧道裂隙水突出力学机制研究 总被引：16，自引：4，他引：12
岩溶地下水是诱发隧道发生突（涌）水地质灾害的主导因素之一,岩溶裂隙水对隧道围岩的危害越来越成为岩溶地区隧道建设中的热点研究问题之一。基于目前岩溶裂隙水突出机制研究现状,运用岩溶地质学、工程水力学和断裂力学相关理论分析岩溶地区隧道水岩相互作用机制,探讨了水岩相互作用对岩溶地区隧道施工发生突（涌）水的影响,揭示岩溶地区隧道裂隙水突出前后过程的力学机制。研究表明：岩溶隧道裂隙水突出是裂隙岩体在岩溶水及水压的持续作用下受施工外力干扰发生劈裂的结果,岩溶水和水压在裂隙岩体突水破坏过程中的力学作用主要体现在4个方面,即突水蓄势期岩溶水对裂隙岩体的软化溶蚀作用、水压对裂隙岩体的劈裂作用,突水失稳期水流的冲刷扩径作用、水压对突水量的动力控制作用。基于上述分析,以断裂力学、弹塑性力学理论为基础,提出岩溶隧道岩溶裂隙水突出的最小岩石防突厚度概念,推导了其半解析解表达式,并为工程实例所验证,其结果可为高风险岩溶地区隧道突水理论与防治措施提供参考。 相似文献
17.
修建大坝、隧洞等工程活动必将对其周围岩体产生扰动,导致赋存于岩体裂隙中的水产生附加水压,从而使岩体在扰动荷载和裂隙水压作用下沿裂隙面失稳扩展。首先基于夹杂理论,推导出扰动荷载所引起的裂隙附加水压的解析式,并应用数值分析进行验证,然后分析裂隙附加水压随岩石力学性质、裂隙形状以及裂隙倾角的变化规律。其次,应用岩石压剪断裂准则,推导出考虑裂隙附加水压的岩体断裂强度解析式。最后结合算例,进一步探讨了裂隙附加水压对岩体断裂强度的影响规律。结果表明,裂隙附加水压降低了岩体断裂强度,增大了岩体发生断裂破坏的倾角范围,使岩体更易于沿裂隙面发生水力劈裂失稳破坏;另外,岩石弹性模量、裂隙形状因子以及裂隙倾角对裂隙附加水压有显著影响,岩体断裂强度随岩石弹性模量和裂隙形状因子的增大而增大,且随裂隙倾角的增大,其增大的趋势更加明显。 相似文献
18.
为了探讨在法向应力和剪应力的共同作用下裂隙开度的变化对于耦合的温度场、渗流场和应力场的作用,引入裂隙的渗透系数与开度关系的“立方定律”,建立了裂隙渗透系数演化式。应用开发的遍有节理岩体双重孔隙-裂隙介质热-水-应力耦合二维有限元程序,以一个假定的位于非饱和地层中的高放废物地质处置库为算例,分别在2组裂隙斜交和正交的条件下,针对与裂隙开度3种计算方式对应的6种工况进行了数值分析,考察了围岩中的温度、孔隙和裂隙水压力、裂隙开度、裂隙的渗透系数、地下水流速、应力的变化、分布状态。结果显示,当裂隙开度仅取决于法向应力时,裂隙开度受压应力作用产生的闭合量最大,从而裂隙水压力最高;而当裂隙开度是法向应力和剪切位移的函数时,由于“剪胀”效应,裂隙开度闭合量较前述情况为小,裂隙水压力居中;而当裂隙开度是常数时,裂隙水压力最低 相似文献
19.
裂隙岩体介质THM耦合问题中的渗透特性研究 总被引：4，自引：0，他引：4
刘亚晨 《地质灾害与环境保护》2004,15(1):80-84
在前人就热、液、力三因素各自影响裂隙岩体渗透特性的研究和本文所进行的温度及附加应力作用下单裂隙岩样实验的基础上．综合分析了裂隙岩体THM耦合过程,以裂隙结构面的开度、岩体裂隙数(包括受温度影响开通裂隙数)、裂隙连通率、附加应力、剪切膨胀为研究对象．建立具有THM耦合特性的裂隙岩体渗流系数张量。 相似文献
20.
Groundwater inflow assessment is essential for the design of tunnel drainage systems, as well as for assessment of the environmental impact of the associated drainage. Analytical and empirical methods used in current engineering practice do not adequately account for the effect of the jointed-rock-mass anisotropy and heterogeneity. The impact of geo-structural anisotropy of fractured rocks on tunnel inflows is addressed and the limitations of analytical solutions assuming isotropic hydraulic conductivity are discussed. In particular, the study develops an empirical correction to the analytical formula frequently used to predict groundwater tunnel inflow. In order to obtain this, a discrete network flow modelling study was carried out. Numerical simulation results provided a dataset useful for the calibration of some empirical coefficient to correct the well-known Goodman’s equation. This correction accounts for geo-structural parameters of the rock masses such as joint orientation, aperture, spacing and persistence. The obtained empirical equation was then applied to a medium-depth open tunnel in Bergamo District, northern Italy. The results, compared with the monitoring data, showed that the traditional analytical equations give the highest overestimation where the hydraulic conductivity shows great anisotropy. On the other hand, the empirical relation allows a better estimation of the tunnel inflow. 相似文献