共查询到20条相似文献，搜索用时 31 毫秒
1.
Liyuan Yu Haijian Su Richeng Liu Hongwen Jing Qingbin Meng Ning Luo 《Arabian Journal of Geosciences》2017,10(19):432
The drill and blast method (D&B) is perhaps the most common excavation method for rock mass, and intense blasting vibrations would induce an excavation damage zone (EDZ) around the excavated space. The tensile failure of rock mass in EDZ at diverse rupture velocities results in various geological disasters in engineering practices. The objective of this paper is to investigate the effect of blasting on the tensile strength of sandstone rock and the influence of loading rate on the disk specimens affected by blasting. We firstly performed a D&B exercise on a sandstone block with a size of 600 mm × 600 mm × 120 mm. Then, a total number of 49 standard disk specimens were prepared from large fragments of this blasting sandstone block and an undamaged block. A series of Brazilian split tests was carried out using these specimens to determine their indirect tensile strength, and to assess the effects of the distance from the blasting source and loading rate (varying from 1.67 × 10?5 to 8.33 × 10?2 mm s?1). The results show that the tensile strength of specimens exhibits an upward trend with increasing distance from the blasting source, to approach that of undamaged rock, following a power function with a positive exponent (0~1). The loading rate affects the tensile mechanical behaviors of disks, in terms of the convergence of microscopic defects, the main load-bearing area, and the absorbed energy at the fracture moment of specimens. Both the tensile strength and absorbed energy have positive linear correlations with the natural logarithm of the loading rate. In addition, the fragmentation degree of disk specimens also increases due to an increasing brittleness of sandstone with the loading rate. 相似文献
2.
Zhang Yue Zhang Qiang-Yong Zhou Xin-Yu Xiang Wen 《Geotechnical and Geological Engineering》2021,39(2):709-718
To study the tensile strength of rock under different loading rates, direct tensile test is the most accurate method. However, the eccentric tension in the process of rock direct tensile test has a significant influence on the test results. In this paper, firstly, a self-developed centering device for rock direct tensile test is introduced, which can effectively eliminate the eccentric tension in the process of rock direct tensile test. Then, with the aid of the self-developed centering device, the direct tensile tests of red sandstone under the loading rates of 0.001 mm/s, 0.01 mm/s and 0.1 mm/s are successfully carried out. After tests, both the macro failure characteristics and the scanning electron microscope micrograph show that the fracture pattern of the rock is caused by pure tensile loading. The stress-strain curves of the direct tensile test of the red sandstone show that the process of the direct tensile test can be roughly divided into four stages. With the increase of loading rate, both of the tensile strength and the peak tensile strain of the rock increase obviously. The direct tensile test of the red sandstone shows obvious loading rate effect.
相似文献3.
开展岩石高温损伤破裂信息识别研究对地热开发和煤炭地下气化等具有重要的指导意义。通过不同高温处理后砂岩在破坏过程中声发射参数RA(上升时间/振幅)和AF(平均频率)值变化,研究高温后砂岩内部不同类型裂纹的发展演化规律。结果表明:砂岩在整个加载过程中以拉张裂纹为主,当加载应力超过峰值应力的80%后,剪切裂纹所占比例迅速增大,可将此作为砂岩发生破坏的前兆;当加热温度超过600℃时,剪切裂纹所占比例上升,超过800℃,剪切裂纹所占比例迅速下降,600℃和800℃可作为砂岩损伤突变的阈值温度;高温后位错塞积现象增多,砂岩塑性特征增强,拉张裂纹所占比例增大。研究成果将对高温作用后岩石破裂失稳前兆信息的识别提供重要的理论基础。 相似文献
4.
Sun Bing Yang Haowei Zeng Sheng Luo Yu 《Geotechnical and Geological Engineering》2022,40(11):5577-5591
The effect law of deformation and failure of a jointed rock mass is essential for underground engineering safety and stability evaluation. In order to study the evolution mechanism and precursory characteristics of instability and failure of jointed rock masses, uniaxial compression and acoustic emission (AE) tests are conducted on sandstones with different joint dip angles. To simulate the mechanical behavior of the rock, a jointed rock mass damage constitutive model with AE characteristic parameters is created based on damage mechanics theory and taking into account the effect of rock mass structure and load coupling. To quantify the mechanism of rock instability, a cusp catastrophe model with AE characteristic parameters is created based on catastrophe theory. The results indicate that when the joint dip angle increases from 0° to 90°, the failure mechanism of sandstone shifts from tensile to shear, with 45° being the critical failure mode. Sandstone's compressive strength reduces initially and subsequently increases, resulting in a U-shaped distribution. The developed damage constitutive model's theoretical curve closely matches the test curve, indicating that the model can reasonably describe the damage evolution of sandstone. The cusp catastrophe model has a high forecast accuracy, and when combined with the damage constitutive model, the prediction accuracy can be increased further. The research results can provide theoretical guidance for the safety and stability evaluation of underground engineering.
相似文献5.
Xiaoshan Shi Da’an Liu Wei Yao Yirui Shi Tiewu Tang Bonan Wang Weige Han 《Arabian Journal of Geosciences》2018,11(2):42
Shale usually exhibits strong anisotropy due to depositional environment and pre-existed microcracks caused by geological loading for a long time. Characterizing mechanical anisotropy properties of shale, especially the tensile strength anisotropy, plays an important role in the successful exploitation of shale gas. In this work, static and dynamic tests with semi-circular bending (SCB) specimen are conducted using hydraulic servo-control machine and modified split Hopkinson pressure bar (SHPB) system, respectively. To survey the tensile strength anisotropy of shale induced by stratification, samples are cored and cut into half by diametrical cutting along different angles relative to the stratification (0°, 30°, 45°, 60°, 90°, C0°). For dynamic tests, the utilization of pulse shaping technique ensures that the samples obtain dynamic equilibrium. The tensile strength values exhibit clear anisotropy under both static and dynamic loading conditions and show typical loading rate dependence at a given angle. An anisotropic index named αk is defined to describe the tensile strength anisotropy at a certain loading rate. The outcomes illustrate that the anisotropic index decreases as the loading rate increases. In addition, failure pattern owns different characteristic under different loading angles with respect to the stratification. These phenomena may be explained by the pre-existing microcracks, and cracks interaction during dynamic loading conditions. 相似文献
6.
Dong Zhu Hong Wen Jing Qian Yin Yi Jiang Zong Xiang Ling Tao 《Arabian Journal of Geosciences》2018,11(20):637
Arc fissure is one of the basic forms of defective rock, where the expansion and evolution mechanism plays an important role in the stability of engineering rock mass under the external load action. Uniaxial compression experiments of sandstone samples that contained various angles of arc fissures (sandstone sample was 80 mm?×?160 mm?×?30 mm) were performed in order to investigate the effect that arc angle α had on the mechanical properties, the failure mode, and the fracture evolution process of sandstone. The results showed that when arc angle α was increased, the peak strength and the strain of the sandstone samples initially decreased before increasing and the minimum peak strength and strain were reached when α?=?15°. The deterioration of the bearing capacity and the number of cracks that appeared during the sandstone loading process decreased as the arc angle of the fissure increased. The arc fissure destruction was primarily initiated from the fragile area of the arch tip. The tensile cracks appeared on the fissure tip and non-tip as the axial force increased. The various arc angle α played an important role in the initiation stress and the rupture evolution of the specimen. 相似文献
7.
Mingze Liu Guang Zhang Guogang Gou Bing Bai Shaobin Hu Xiaochun Li 《Natural Hazards》2018,90(3):1137-1151
Reasonable determination of formation fracturing pressure concerns the stable operation of underground fluid injection projects. In this work, we studied the effect of unsteady flow on fracturing pressure. Hydraulic fracturing tests on low permeable sandstone were conducted with the injection rate between 0.1 and 2.0 ml/min. Then, the fracturing pressure prediction models for hollow cylinder under both unsteady flow and steady flow conditions were deduced. Finally, the effect of unsteady flow on the fracturing pressure was studied based on the experimental result and several influence factors. It was shown that fracturing pressure increased with the elevated pressurization rate in the tests, while the slope of the variation curve decreases. The model considering unsteady flow can reflect the variation tendency of fracturing pressures in experiments, while fracturing pressures from the model considering steady flow are invariant with different pressurization rates. Fracturing pressure decreases with the elevated rock permeability and increases with the elevated fluid viscosity, and these two effects are actually generated by the unsteady flow. Whether to consider the unsteady flow has no significant influence on the effect of rock tensile strength on fracturing pressure when the tensile strength is very low. However, when the tensile strength is high, the effect of unsteady flow cannot be neglected. 相似文献
8.
高温后大理岩动态劈裂拉伸试验研究 总被引：2，自引：0，他引：2
为了研究高温处理后的岩石材料在冲击加载速率作用下的动态劈裂拉伸性能,利用大直径分离式霍普金森压杆试验设备对经历不同高温作用冷却后的“大理岩”平台巴西圆盘试样进行不同加载速率作用下的径向冲击试验。研究了高温后大理岩的动态劈裂拉伸强度及动态劈裂破坏形式随温度和冲击加载速率的变化规律。试验结果表明,与静态劈裂拉伸强度相比,经历不同高温作用冷却后,大理岩的动态劈裂拉伸强度有明显的提高,表现出显著的冲击加载速率强化效应,同一冲击加载速率作用下,随着温度的升高,动态劈裂拉伸强度表现出先增大后减小的变化趋势;高温后大理岩的动态劈裂破坏形式受到冲击加载速率和温度的共同影响。 相似文献
9.
岩土类材料的强度强烈依赖于含水率和温度条件.以兰州兰山砂岩为研究对象,分别进行了不同温度（+20℃、-5℃、-10℃）和不同含水率（干燥、天然含水率和饱和状态）条件下岩石的巴西圆盘劈裂试验.试验结果表明,常温下,岩石抗拉强度随含水率增加而急剧减小,试样饱和时软化、崩解,丧失承载能力;在不同负温条件下,天然含水状态的试样抗拉强度最大,干燥状态下最小;在-10~+20℃范围内,干燥岩石强度随温度升高,抗拉强度增大,含水岩石均是随温度升高,抗拉强度减小,但饱和岩石在-5℃时抗拉强度最大.含水率和温度对岩样强度的影响存在临界值,超过临界值,岩样强度随上述因素反向变化.试验结论为岩土类材料劈裂强度的标准化测试及其工程应用提供了重要的基础数据参考. 相似文献
10.
为研究加载速率对砂岩抗拉强度的影响效应及影响机制,设计开展5种加载速率的劈裂试验,综合分析抗拉强度、破坏特征、能量参数和劈裂面微观形貌变化规律及相关性。结果表明,(1) 随着加载速率增大,砂岩劈裂抗拉强度逐渐增大,总体呈现先陡后缓的趋势,加载速率在0.01～0.10 kN/s范围内时抗拉强度增长迅速,0.10～1.00 kN/s范围内时抗拉强度增长趋势渐缓;(2) 随着加载速率的增大,岩样吸收的总能量增大,弹性应变能占总能量的比值逐渐增大,耗散能占总能量的比值逐渐减小,加载至破坏时裂纹扩展形成宏观劈裂面的时间呈数量级减小,达到峰值应力时弹性应变能的释放,导致岩样破坏的突发性增强,使得劈裂面形貌特征在宏观和微观上逐渐变得复杂,对应抗拉强度逐渐增大;(3) 在岩石劈裂试验过程中加载速率、能量参数、劈裂面形貌特征与抗拉强度密切相关,加载速率影响加载过程中能量的总量与分配,能量参数的变化直接影响岩样的破坏过程及劈裂面的形貌特征,最后宏观上表现为抗拉强度的差异。文中相关分析方法和思路可为类似试验提供较好的参考。 相似文献
11.
Sandstone alterations triggered by fire-related temperatures 总被引：1，自引：1，他引：0
Z. Kompaníková M. Gomez-Heras J. Michňová T. Durmeková J. Vlčko 《Environmental Earth Sciences》2014,72(7):2569-2581
The aim of the study was to identify and describe changes in two different sandstone types when undergoing different environmental and extreme temperature regimes to assess the possibility of finding insolation weathering and how these sandstones would behave during and after a fire. The first step was the simulation in the laboratory of temperature regimes up to 60 °C which would correspond to extreme events that could be found in insolation cycles even in Central Europe and the second one was the temperature above 200 °C simulating in laboratory conditions the thermal regime of a potential fire situation at temperatures up to 200, 400, 600 and 800 °C. Heating the samples above 400 °C led to gradual changes in mineral composition, colour, surface roughness and physical properties reaching, eventually, total rock breakdown through spalling and granular disaggregation. The different behaviour of sandstones exposed to high temperatures is mainly caused by their different mineral composition with various ratios of minerals that are more or less chemically stable at high temperatures as well as by the differences in the porosity. 相似文献
12.
Variations in the mechanical properties (compressive strength, elastic modulus, tensile strength, and fracture toughness) of granite were analyzed as functions of temperature. It was found that above 200 °C, tensile strength and fracture toughness tended to decrease with temperature, while variations in the compressive strength and elastic modulus demonstrated decreasing trends when the heating temperature exceeded 400 °C. The temperature ranges of room temperature—200 and above 600 °C—corresponded to an undamaged state and strongly/completely damaged state, respectively. It is suggested that 400 °C might be a critical threshold of thermal damage to granite. Based on results of statistical tests, a sharp decrease in mechanical properties can be recognized, accompanied by a drastic growth in peaking strain and acoustic emission rate. This phenomenon may be associated with the α/β phase transition of quartz. 相似文献
13.
为了探究川藏交通廊道沿线典型岩石冻融循环条件下的劣化规律,选取昌都-林芝段的花岗岩、片麻岩和砂岩为试验对象,开展冻融循环条件下岩石加卸荷试验,结果表明:（1）随着冻融循环次数的增加,岩石抗压强度损失率达30%,粘聚力降幅达18.4%,内摩擦角降幅达10.5%,弹性模量逐渐下降,泊松比逐渐增加;（2）三轴压缩试验中,岩样的变形模量呈现与抗压强度类似的劣化趋势,但是变形模量的劣化幅度比抗压强度劣化幅度大;冻融循环作用下岩石抗压强度越大劣化程度越低,对砂岩的劣化最明显,片麻岩次之,花岗岩最小;（3）与三轴压缩试验相比,在卸围压试验中,冻融循环作用对岩石的卸荷量同样有劣化作用,卸荷程度较小时岩石劣化并不明显,随着卸荷量的逐渐增加,卸荷量大于80%时,岩石的变形模量呈指数型下降,泊松比呈指数型增加;（4）随着冻融循环次数的增加,三轴压缩试验中由拉张和剪切破坏造成的裂纹数量增多;卸围压试验中岩石以拉张破坏为主;岩石微裂纹数量增加的同时,不平整度增加,矿物颗粒之间的胶结状态变差;（5）综合试验结果分析,冻融作用对岩石劣化作用最强的为砂岩,其次是片麻岩,最弱为花岗岩. 相似文献
14.
Manish Kumar Jha A. K. Verma Pradeep Kumar Gautam Anil Negi 《Journal of the Geological Society of India》2017,90(3):267-272
Shale is an important rock due to its suitability for different engineering and scientific applications. Elevated temperature may cause major deformation or damage in shale rock and it may be of irreversible in nature. Such damage have adverse effect on the physicomechnical properties of shale rock. The uniaxial compressive strength and tensile strength of two shales (upper Vindhyan basin, India) have been estimated at elevated temperature using point load strength index method. The rock samples have been analyzed at various temperatures starting from room temperature to 900 °C. The effect of elevated temperature on the physicomechanical properties and their influence on the uniaxial compressive strength has been studied in detail. Damage induced, in both shale have been estimated using compressional wave velocity. The analysis of the experimental result shows that the uniaxial compressive strength decreases from 63.45 to 18.45 MPa and 60.94 to 22.22 MPa, for Jhiri and Ganurgarh shale respectively. Tensile strength of shales have been also estimated. The value of tensile strength decreases from 3.65 to 1.05 MPa and 3.46 to 1.26 MPa respectively for Jhiri and Ganurgarh shale. Multivariate regression analysis has been carried out to obtain the correlation between physicomechanical properties and uniaxial compressive strength of Jhiri and Ganurgarh shale. 相似文献
15.
M. Farooq Ahmed Umer Waqas Muhammad Arshad J. David Rogers 《Arabian Journal of Geosciences》2018,11(22):728
Temperature is one of the variables that influence the elasto-plastic behavior and integrity of rock outcrops. Fluctuations in temperature can trigger alteration of some of the mineral properties and impact the brittle-plastic transition. Initiation and propagation of thermally induced tension cracks tend to weaken most rock types. The principal goal of this study was to anticipate impacts of thermal stress-strain cycles on the dynamic response of representative rock units exposed in the Khewra Gorge of the Salt Range Punjab of Pakistan. Ten types of sedimentary rock units were sampled, including marl, dolomite, three types of limestone, and five different sandstones exhibiting varying characteristics in outcrop. Boulder specimens were collected from the field and transported to the laboratory to prepare 50 drill cores that could be subjected to thermal cycling between 50 and 200 °C in increments of 50 °C. Room temperature core samples were tested using an Erudite resonance frequency meter to measure their Q-factors and the resonance frequency (Fr) at an applied loading frequency of 7 KHz with 0.01 V output voltage. Results suggest that thermal cycling tends to reduce the dynamic Young’s modulus (Ed) and Q-factor. Other parameters, such as damping ratio (ξ), specific damping capacity (Ψ), and loss factor (?) appeared to increase with increasing temperature cycles, likely as a result of developing thermally induced tensile fractures. The resultant values of the null hypothesis (t-critical and t-stats) suggests that the null hypothesis can be discarded because there was no observable difference between the measured and expected values for the cores tested. The observations and data emanating from this study might be useful in designing low-level radioactive waste landfills, nuclear waste repositories, and deep underground excavations where the increased temperature could alter the mechanical behavior of the parent rock mass. 相似文献
16.
为分析巴西圆盘劈裂法在层状岩体抗拉强度试验中的适用性,在以往层状岩体巴西圆盘劈裂试验成果分析基础上,选取层理砂岩为试验对象,设计并进行了考虑不同层理角度的砂岩巴西圆盘劈裂试验。分析结果表明,（1）层状岩体抗拉强度的各向异性特点非常明显,层理角度对各种层状岩体的劈裂抗拉强度的影响规律是基本类似的,只是影响程度不一样;（2）不同层理角度圆盘试样的破裂面形状差别较大,其破坏模式可以归纳为直线型、折线型和弧形型;（3）当层理角度0°＜β＜90°时,破裂面的发展规律不能严格满足巴西圆盘劈裂试验力学理论模型的假定,采用式（1）计算得到的劈裂抗拉强度只能是一个近似的值;（4）当圆盘试样加载线两侧的岩石材料、层理结构对称分布时,加载时圆盘内的应力分布可以较好地满足其理论计算模型,其试验结果比较准确。研究成果可为层状岩体抗拉强度的准确测定提供较好的参考。 相似文献
17.
Tensile Strength of Rock Under Elevated Temperatures 总被引：4，自引：0，他引：4
Rock strength affects the behaviour of rocks differently under different conditions such as temperature, time, pressure, presence
of fluids, rock mass characteristics and stress history of rock in a natural environment. It is not always easy to replicate
such conditions of undisturbed rock in a laboratory scale. Hence, it is imperative to study the rock behaviour with respect
to every such condition which the rock experiences since its time of formation. Temperature is one of the key parameters which
influence the rock throughout its history, ranging from the conditions of formation, experience of depth (loading/unloading)
or deformational and metamorphic history. Also, increase in rock temperature; say due to the thermal stress changes like disposal
of spent nuclear fuels affects the strength of the surrounding rock. In this work, the effects of temperature on the tensile
strength of rock have been studied. The results obtained were interesting as the strength of rock is found to increase considerably
up to a particular temperature after which it starts falling by as much as 70% around 250°C. 相似文献
18.
Tubing Yin Xibing Li Kaiwen Xia Sheng Huang 《Rock Mechanics and Rock Engineering》2012,45(6):1087-1094
The effect of thermal treatment on the dynamic fracture toughness of Laurentian granite (LG) was investigated in this work. Notched semi-circular bend (NSCB) LG specimens are heat treated at temperatures up to 850?°C. The micro-cracks in the rock samples induced by thermal treatment are examined by scanning electron microscope (SEM). The microscopic observations are consistent with the subsequent P-wave velocity measurements, which shows that the P-wave velocity decreases with the treatment temperature monotonically when the temperature is higher than 250?°C. Dynamic fracture toughness measurements are then carried out on these samples with the dynamic load exerted by a modified split Hopkinson pressure bar (SHPB) system. The relationship between fracture toughness and treatment temperature is investigated. Experimental results show that fracture toughness increases with the loading rate but decreases with the treatment temperature. However, when the heating temperature is below 250?°C and above 450?°C, the dependence of dynamic fracture toughness on the temperature is different from other temperatures, which can be explained by the physical processes at the microscopic level of the rock due to heating. At treatment temperatures below 250?°C, the thermal expansion of grains leads to an increase in the toughness of the rock. At treatment temperatures above 450?°C, the sources of weakness such as grain boundaries and phase transition of silicon are depleted, and as a result the decrease in fracture toughness is not as significant as other treatment temperature ranges. 相似文献
19.
Characterization of Strength of Intact Brittle Rock Considering Confinement-Dependent Failure Processes 总被引：1，自引：0，他引：1
As technologies for deep underground development such as tunneling underneath mountains or mass mining at great depths (>1,000 m) are implemented, more difficult ground conditions in highly stressed environments are encountered. Moreover, the anticipated stress level at these depths easily exceeds the loading capacity of laboratory testing, so it is difficult to properly characterize what the rock behavior would be under high confinement stress conditions. If rock is expected to fail in a brittle manner, behavior changes associated with the relatively low tensile strength, such as transition from splitting to the shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile or extensional failure in heterogeneous rocks. The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it must be expected that the transition in the failure mechanism, from tensile to shear, occurs as the confinement level increases and conditions for extensional failure are prevented or strongly diminished. However, conventional failure criteria implicitly consider only the shear failure mechanism (i.e., failure envelopes touching Mohr stress circles), and thus, do not explicitly capture the transition of failure modes from tensile to shear associated with confinement change. This paper examines the methodologies for intact rock strength determination as the basic input data for engineering design of deep excavations. It is demonstrated that published laboratory test data can be reinterpreted and better characterized using an s-shaped failure criterion highlighting the transition of failure modes in brittle failing rock. As a consequence of the bi-modal nature of the failure envelope, intact rock strength data are often misinterpreted. If the intact rock strength is estimated by standard procedures from unconfined compression tests (UCS) alone, the confined strength may be underestimated by as much as 50 % (on average). If triaxial data with a limited confinement range (e.g., σ3 ? 0.5 UCS due to cell pressure limitations) are used, the confined strength may be overestimated. Therefore, the application of standard data fitting procedures, without consideration of confinement-dependent failure mechanisms, may lead to erroneous intact rock strength parameters when applied to brittle rocks, and consequently, by extrapolation, to correspondingly erroneous rock mass strength parameters. It follows that the strength characteristics of massive rock differ significantly in the direct vicinity of excavation from that which is remote with higher confinement. Therefore, it is recommended to adopt a differentiated approach to obtain intact rock strength parameters for engineering problems at lower confinement (near excavation; e.g., excavation stability assessment or support design), and at elevated confinement (typically, when the confinement exceeds about 10 % of the UCS) as might be encountered in wide pillar cores. 相似文献
20.
Effect of Rapid Thermal Cooling on Mechanical Rock Properties 总被引：1，自引：1，他引：0
Laboratory tests have been conducted to investigate the effects of rapid thermal cooling on various rock specimens including igneous, sedimentary, and metamorphic rocks. At first, various types of thermal loading were conducted: heating up to 100, 200, and 300 °C, followed by rapid cooling with a fan. In addition, multiple cyclic thermal cooling (10, 15 and 20 cycles) with a maximum temperature of only 100 °C was conducted. Experiments included edge notched disc (END) tests to determine the Mode I fracture toughness, Brazilian disc tests to determine tensile strength, seismic tests to determine P-wave velocity, and porosity tests leading to meaningful results. Even though only small changes of temperature (rapid cooling from 100 °C to room temperature) were applied, the results showed that crack growth occurred in some rock types (granite, diabase with ore veins, and KVS) while crack healing occurred in other rock types (diabase without ore veins, quartzite, and skarn). To better understand the results, 3D transient thermo-mechanical analysis was conducted using the ANSYS program. The results indicated that there was a thin region near the outside of the specimen where large tensile stresses occur and microcracking would be expected, and that there was a large area in the middle of the specimen where lower magnitude compressive stresses occur and crack closure would be expected. It was found that the more heterogeneous and more coarse-grained rock types are more likely to exhibit crack growth, while less heterogeneous and more fine-grained rocks are more likely to exhibit crack healing. 相似文献