首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 78 毫秒
1.
A worldwide dataset of organic material from 553 samples belonging to coal and carbonaceous materials was used to analyze the evolution of hydrogen index (HI) and bitumen index (BI) with increasing thermal maturity. Basic statistical analyses were applied to detect the boundary lines of HImax and BImax in delineating the upper and lower limits of the HI and BI bands for the majority of samples. In addition, cross-plots of HI or BI versus maturity (Ro% and T max) also provide criteria for defining the HImax and BImax boundary lines. The constructed HI and BI bands are broad at low maturities and become narrower with increasing thermal maturities. The petroleum generation potential is completely exhausted at the vitrinite reflectance of 2.0–2.2% or T max of 510–520°C. An increase in HI implies extra petroleum generation which was related to changes in structure of organic materials. A declining BI means that the oil expulsion window starts to occur at the vitrinite reflectance range of 0.75–1.05%. The petroleum potential can be divided into four different areas based on the cross-plot of HI versus Ro%. The highest petroleum potential area is located in section II with Ro = 0.6–1.0% and HI > 100. The oil generation potential is rapidly exhausted at section III with Ro > 1.0%. This result is also in accordance with the result of curve regression of HI versus Ro% based on 80 samples with Ro = 1.02–3.43% (R 2 = 0.72). Overall, the total oil window can be extended up to Ro = ~1.25–1.95%. Finally, in the cross-plots of S1 versus S2, shale or C-shale exhibits a higher and slowly decreased slope, compared with a lower and then sharply increased slope of coal samples, which is attributable to their compositional difference in organic material.  相似文献   

2.
Coaly source rocks are sufficiently different from marine and lacustrine source rocks in their organic matter characteristics to warrant separate guidelines for their assessment using Rock-Eval pyrolysis. The rank threshold for oil generation is indicated by the increase in BI (S1/TOC) at Rank(Sr)9–10 (Tmax 420–430 °C, Ro 0.55–0.6%), and the threshold for oil expulsion is indicated by the peak in QI ([S1+S2]/TOC) at Rank(Sr)11–12.5 (Tmax 430–440 °C, Ro 0.65–0.85%). The pronounced rank-related increase in HI (S2/TOC) prior to oil expulsion renders the use of immature samples inappropriate for source rock characterisation. A more realistic indication of the petroleum generative potential and oil expulsion efficiency of coaly source rocks can be gained from samples near the onset of expulsion. Alternatively, effective HI′ values (i.e. HIs near the onset of expulsion) can be estimated by translating the measured HIs of immature samples along the maturation pathway defined by the New Zealand (or other defined) Coal Band. Coaly source rocks comprise a continuum of coaly lithologies, including coals, shaly coals and coaly mudstones. Determination of the total genetic potential of coaly source rock sequences is best made using lithology-based samples near the onset of expulsion.  相似文献   

3.
A worldwide data set of 1,085 samples containing organic matter of the type II/III kerogen from Carboniferous to Cenozoic was used to analyse the evolution of the hydrogen index (HI), quality index (QI), and bitumen index (BI) with increasing thermal maturity. The HImax, QImax and BImax lines were defined, based on statistical analysis and cross-plots of HI, QI and BI versus the vitrinite reflectance (%Ro) and T max (°C). The constructed HI, QI and BI bands were broad at low maturities and gradually narrowed with increasing thermal maturity. The petroleum generation potential is completely exhausted at a vitrinite reflectance of 2.0–2.2 % and T max of 510–520 °C. An increase in HI and QI suggests extra petroleum potential related to changes in the structure of the organic material. A decline in BI signifies the start of the oil window and occurs within the vitrinite reflectance range 0.75–1.05 % and T max of 440–455 °C. Furthermore, petroleum potential can be divided into four different parts based on the cross-plot of HI versus %Ro. The area with the highest petroleum potential is located in “Samples and methods” with %Ro = 0.6–1.0 %, and HI > 100. Oil generation potential is rapidly exhausted at “Results and discussion” with %Ro > 1.0 %. This result is in accordance with the regression curve of HI and QI with %Ro based on 80 samples with %Ro = 1.02–3.43 %. The exponential equation of regression can thus be achieved: HI = 994.81e?1.69Ro and QI = 1,646.2e?2.003Ro (R 2 = 0.72). The worldwide organic material data set defines two range of oil window represented by the upper and lower limits of the BI band: %Ro 0.75–1.95 %, T max 440–525 °C, and %Ro 1.05–1.25 %, T max 455–465 °C, respectively.  相似文献   

4.
In this study, organic matter content, type and maturity as well as some petrographic and physical characteristics of the Jurassic coals exposed in the eastern Taurus were investigated and their depositional environments were interpreted.The total organic carbon (TOC) contents of coals in the Feke–Akkaya, Kozan–Gedikli and Kozan–Kizilinc areas are 24.54, 66.78 and 49.15%, respectively. The Feke–Akkaya and Kozan–Kizilinc coals have low Hydrogen Index (HI) values while the Kozan–Gedikli coals show moderate HI values. All coal samples display very low Oxygen Index (OI) values. The Kozan–Gedikli coals contain Type II organic matter (OM), the Feke–Akkaya coals contain a mixture of type II and type III OM; and the Kozan–Kizilinc coals are composed of Type III OM. Sterane distribution was calculated as C27 > C29 > C28 from the m/z 217 mass chromatogram for all coal samples.Tmax values for the Feke–Akkaya, Kozan–Gedikli and Kozan–Kizilinc coals are 439, 412 and 427 °C. Vitrinite reflectance values (%Ro) for the Feke–Akkaya and Kozan–Kizilinc coal samples were measured as 0.65 and 0.51 and these values reveal that the Feke–Akkaya and Kozan–Kizilinc coals are at subbituminous A or high volatile C bituminous coal stage. On the basis of biomarker maturity parameters, these coals have a low maturity.The pristane/phytane (Pr/Ph) ratios for the Feke–Akkaya, Kozan–Gedikli and Kozan–Kizilinc coals are 1.53, 1.13 and 1.25, respectively. In addition, all coals show a homohopane distribution which is dominated by low carbon numbers, and C35 homohopane index is very low for all coal samples. All these features may indicate that these coals were deposited in a suboxic environment.The high sterane/hopane ratios with high concentrations of steranes, low Pr/Ph ratios and C25/C26 tricyclic ratios > 1 may indicate that these coals formed in a swamp environment were temporarily influenced by marine conditions.  相似文献   

5.
Thermally metamorphosed Tertiary age coals from Tanjung Enim in South Sumatra Basin have been investigated by means of petrographic, mineralogical and chemical analyses. These coals were influenced by heat from an andesitic igneous intrusion. The original coal outside the metamorphosed zone is characterized by high moisture content (4.13–11.25 wt.%) and volatile matter content (> 40 wt.%, daf), as well as less than 80 wt.% (daf) carbon and low vitrinite reflectance (VRmax = 0.52–0.76%). Those coals are of subbituminous and high volatile bituminous rank. In contrast the thermally metamorphosed coals are of medium-volatile bituminous to meta-anthracite rank and characterized by low moisture content (only < 3 wt.%) and volatile matter content (< 24 wt.%, daf), as well as high carbon content (> 80 wt.%, daf) and vitrinite reflectance (VRmax = 1.87–6.20%). All the studied coals have a low mineral matter content, except for those which are highly metamorphosed, due to the formation of new minerals.The coalification path of each maceral shows that vitrinite, liptinite and inertinite reflectance converge in a transition zone at VRmax of around 1.5%. Significant decrease of volatile matter occurs in the zone between 0.5% and 2.0% VRmax. A sharp bend occurs at VRmax between 2.0% and 2.5%. Above 2.5%, the volatile matter decreases only very slightly. Between VRr = 0.5% and 2.0%, the carbon content of the coals is ascending drastically. Above 2.5% VRr, the carbon content becomes relatively stable (around 95 wt.%, daf).Vitrinite is the most abundant maceral in low rank coal (69.6–86.2 vol.%). Liptinite and inertinite are minor constituents. In the high rank coal, the thermally altered vitrinite composes 82.4–93.8 vol.%. Mosaic structures can be recognized as groundmasss and crack fillings. The most common minerals found are carbonates, pyrite or marcasite and clay minerals. The latter consist of kaolinite in low rank coal and illite and rectorite in high rank coal. Change of functional groups with rank increase is reflected most of all by the increase of the ratio of aromatic C–H to aliphatic C–H absorbances based on FTIR analysis. The Oxygen Index values of all studied coals are low (OI < 5 mg CO2/g TOC) and the high rank coals have a lower Hydrogen Index (< 130 mg HC/g TOC) than the low rank coals (about 300 mg HC/g TOC). Tmax increases with maturity (420–440 °C for low rank coals and 475–551 °C for high rank coals).Based on the above data, it was calculated that the temperature of contact metamorphism reached 700–750 °C in the most metamorphosed coal.  相似文献   

6.
The objective of the study was to characterize changes of reflectance, reflectance anisotropy and reflectance indicating surface (RIS) shape of vitrinite, sporinite and semifusinite subjected to thermal treatment under inert conditions. Examination was performed on vitrinite, liptinite and inertinite concentrates prepared from channel samples of steam coal (Rr = 0.70%) and coking coal (Rr = 1.25%), collected from seam 405 of the Upper Silesian Coal Basin. The concentrates were heated at temperatures of 400–1200 °C for 1 h time in an argon atmosphere.All components examined in this study: vitrinite, sporinite and semifusinite as well as matrix of vitrinite and liptinite cokes, despite of rank of their parent coal, show, in general, the most important changes of reflectance value and optical anisotropy when heated at 500 °C, 800 °C (with the exception of bireflectance value of sporinite) and 1200 °C.After heating the steam coal at 1200 °C, the vitrinite and the semifusinite reveal similar reflectances, whereas the latter a slightly stronger anisotropy. Sporinite and matrix of liptinite coke have lower reflectances but anisotropy (Rbi and Ram values) similar to those observed for vitrinite and semifusinite. However, at 1000 °C sporinite and matrix of liptinite coke have the highest reflectivity of the studied components. The RIS at 1200 °C is the same for all components.The optical properties of the three macerals in the coking coal become similar after heating at 1000 °C. Coke obtained at 1200 °C did not contain distinguishable vitrinite grains. At 1200 °C semifusinite and vitrinite coke matrix have highest Rr values among the examined components. Maximum reflectance (Rmax) reach similar values for vitrinite and sporinite, slightly lower for semifusinite. Matrix of liptinite coke and matrix of vitrinite coke have considerably stronger anisotropy (Rbi and Ram values) than other components. RIS at 1200 °C is also similar for all components.  相似文献   

7.
The maceral and microlithotype composition of selected coals has been investigated with respect to the grinding properties, specifically Hardgrove grindability index (HGI), of the coals. The study expands upon previous investigations of HGI and coal petrology by adding the dimension of the amount and composition of the microlithotypes. Coal samples, both lithotypes and whole channels, were selected from restricted rank ranges based on vitrinite maximum reflectance: 0.75–0.80% Rmax, 0.85–0.90% Rmax and 0.95–1.00% Rmax. In this manner, the influence of petrographic composition can be isolated from the influence of rank. Previous investigations of high volatile bituminous coals demonstrated that, while rank is an important factor in coal grindability, the amount of liptinite and liptinite-rich microlithotypes is a more influential factor. In this study, we provide further quantitative evidence for the influence of microlithotypes on HGI and, ultimately, on pulverizer performance.  相似文献   

8.
Marine, organic-rich rock units commonly contain little for vitrinite reflectance (VR0) measurement, the most commoly used method of assessing thermal maturity. This is true of the Lower Jurassic “Nordegg Member”, a type I/II, sulphur-rich source rock from the Western Canada Sedimentary Basin. This study examines the advantages and pitfalls associated with the use of Rock-Eval Tmax and solid bitumen reflectance (BR0) to determined maturity in the “Nordegg”. Vitrinite reflectance data from Cretaceous coals and known coalification gradients in the study area are used to extrapolate VR0 values for the “Nordegg”.Tmax increases non-linearly with respect to both BR0 and extrapolated VR0 values. A sharp increase in the reflectaance of both solid bitumen and vitrinite occurs between Tmax 440–450°C, and is coincident with a pronounced decrease in Hydrogen Index values and the loss of solid bitumen and telalginite fluorescence over the same narrow Tmax interval. This Tmax range is interpreted as the main zone of hydrocarbon generation in the “Nordegg”, and corresponds to extrapolated VR0 values of 0.55–0.85%. The moderate to high sulphur contents in the kerogen played a significant role in determining the boundaries of the “Nordegg” oil window.A linear relationship between BR0 and extrapolated VR0, as proposed elsewhere, is not true for the “Nordegg”. BR0 increases with respect to extrapolated VR0 according to Jacob's (1985) formula (VR0=0.618×(BR0)+0.40) up to VR0≈0.72% (BR0≈0.52%). Beyond this point, BR0 increases sharply relative to extrapolated VR0, according to the relatioship VR0 = 0.277 × (BR0) + 0.57 (R2 = 0.91). The break in the BR0−VR0 curve at 0.72%VR0 is thought to signifiy the peak of hydrocarbon generation and represents a previously unrecognized coalification jump in the solid bitumen analogous to the first coalification jump of liptinites.  相似文献   

9.
Leping coal is known for its high content of “barkinite”, which is a unique liptinite maceral apparently found only in the Late Permian coals of South China. “Barkinite” has previously identified as suberinite, but on the basis of further investigations, most coal petrologists conclude that “barkinite” is not suberinite, but a distinct maceral. The term “barkinite” was introduced by (State Bureau of Technical Supervision of the People's Republic of China, 1991, GB 12937-91 (in Chinese)), but it has not been recognized by ICCP and has not been accepted internationally.In this paper, elemental analyses (EA), pyrolysis-gas chromatography, Rock-Eval pyrolysis and optical techniques were used to study the optical features and the hydrocarbon-generating model of “barkinite”. The results show that “barkinite” with imbricate structure usually occurs in single or multiple layers or in a circular form, and no definite border exists between the cell walls and fillings, but there exist clear aperture among the cells.“Barkinite” is characterized by fluorescing in relatively high rank coals. At low maturity of 0.60–0.80%Ro, “barkinite” shows strong bright orange–yellow fluorescence, and the fluorescent colors of different cells are inhomogeneous in one sample. As vitrinite reflectance increases up to 0.90%Ro, “barkinite” also displays strong yellow or yellow–brown fluorescence; and most of “barkinite” lose fluorescence at the maturity of 1.20–1.30%Ro. However, most of suberinite types lose fluorescence at a vitrinite reflectance of 0.50% Ro, or at the stage of high volatile C bituminous coal. In particular, the cell walls of “barkinite” usually show red color, whereas the cell fillings show yellow color under transmitted light. This character is contrary to suberinite.“Barkinite” is also characterized by late generation of large amounts of liquid oil, which is different from the early generation of large amounts of liquid hydrocarbon. In addition, “barkinite” with high hydrocarbon generation potential, high elemental hydrogen, and low carbon content. The pyrolysis products of “barkinite” are dominated by aliphatic compounds, followed by low molecular-weight aromatic compounds (benzene, toluene, xylene and naphthalene), and a few isoprenoids. The pyrolysis hydrocarbons of “barkinite” are mostly composed of light oil (C6–C14) and wet gas (C2–C5), and that heavy oil (C15+) and methane (C1) are the minor hydrocarbon.In addition, suberinite is defined only as suberinized cell walls—it does not include the cell fillings, and the cell lumens were empty or filled by corpocollinites, which do not show any fluorescence. Whereas, “barkinite” not only includes the cell walls, but also includes the cell fillings, and the cell fillings show bright yellow fluorescence.Since the optical features and the hydrocarbon-generating model of “barkinite” are quite different from suberinite. We suggest that “barkinite” is a new type of maceral.  相似文献   

10.
Thermally altered pods of coal of very high rank have been observed in a high-volatile-bituminous coal seam in the eastern side of Eagle Mountain, Elk Valley Coalfield, British Columbia. Rank changes have been measured over a strike distance of 7.5 m from 1.24% to 7.1% Ro max, corresponding to a rank gradient of 0.78% Rom−1.Petrologically, unaltered to extremely altered vitrinite showing nongranular (basic) anisotropy, mosaic-textured liptinite and pyrolytic carbon are the most abundant components. The limited presence of mosaic on vitrinite is an indication that the coal seam may have been weathered prior to being heat-affected.Evidence points to localized temperatures as high as 1,000°C, which could have been caused by a lightning strike. The eastern side of Eagle Mountain has experienced higher temperatures than the western side, and it appears that the heat ‘front’ and zone of alteration have an irregular pattern, pointing to saturation of parts of the coal seam by water.Four types of pyrolytic carbon having distinct morphology, anisotrophy and optical path with increasing temperature were observed. Reflectance of pyrolytic carbon falls within the zone of heat-affected coals, whereas the optical path of heat-affected Seam 15 samples is different from that of fresh coal with increasing rank.Finally, the reflectance of vitrinite in heat-affected coal is higher than the reflectance of vitrinite in carbonaceous shale in the Seam 15 section.  相似文献   

11.
Thermogravimetric Fourier transform infrared spectroscopy (TG-FTIR) analyses were carried out on two sets of isolated kerogens covering a wide maturity range from low mature (0.46% Ro) through the end of oil and gas generation (maximum Ro = 5.32%). Data onweight percent and Tmax for evolution of methane, volatile tars, ethylene, SO2, NH3, CO2, and CO are reported. The Tmax of methane shows the most consistent response to increasing maturation in both sets of samples. Results are comparable to those of whole rocks from an Alaskan North Slope well analyzed previously. The collective data for both whole rocks and isolated kerogens shows a generally linear correlation between %Ro and Tmax of methane, with the exception of Ro of about 2.0% where a dip in the curve occurs. The slope of the correlation line was steeper for the predominantly terrigenous Wilcox kerogen than for more marine Colorado kerogen or for the Alaskan North Slope whole rock samples, probably reflecting differences in the chemical nature of various kerogen sets, which is also reflected by differences in the shapes of the pyrolysis curves of SO2, CO2, CO, H2O, and ethylene. These preliminary data indicate that Tmax of methane is a good maturation indicator for whole rocks and isolated kerogens up to an Ro of about 4%, which includes all of the wet gas and a considerable portion of the dry gas generation zones. This correlation was also observed for samples containing migrated bitumen, where it was not possible to obtain a reliable Tmax for the volatile tar (S2) peak. The more terrigenous Wilcox kerogens also showed a good correlation of the Tmax of ethylene with %Ro. Tmax of ammonia evolution did not correlate with maturity and occurred 100–200°C lower than previously found for whole rocks, consistent with a whole-rock source of pyrolytic ammonia for Alaskan whole rock samples. HI and OI indices were calculated in several ways and plotted to reflect kerogen type as well as both the residual oil and gas generation potential. The ratio of pyrolyzable to combustible sulfur (evolved as SO2) was independent of maturity and showed a clear difference between the more terrigenous Wilcox kerogens and the more marine Colorado kerogens.  相似文献   

12.
The Rock-Eval pyrolysis and TOC analysis have been widely used to evaluate the source rock quality. The atomic H/C ratio of kerogen, however, has been overlooked in source rock evaluation. In this study, coal and carbonaceous samples, including 26 from northwestern Taiwan, 12 from China, and 4 from the United States were analyzed, and integrated with 157 published data, to explore the significance of atomic H/C ratio as a parameter of source rock evaluation. Two different linear trends were observed in the cross-plot of S 1 versus S 2. Field outcropped shale or C-shale exhibits a steeper slope compared to that of coal samples which can be attributed to the compositional difference in their organic material. A rather strong positive correlation for H% versus S 2 illustrates the contribution of H-containing macerals, especially exinite. Organic matters in the samples studied are of type II/III kerogen based on the relationship between HI and T max. The H/C ratio, as well as the HI, S 1, and S 2, generally decreases with the maturity increasing. The H/C ratio decreases slightly from 1.1 to 0.7 with the maturity increasing from R o 0.55 to 0.85%. Samples with H/C ratio in this range show significant change in certain other geochemical parameters (e.g. HI, S 1, S 2, S 1 + S 2, S 1/(S 1 + S 2), S 1/TOC, (S 1 + S 2)/TOC, T max). The (S 1 + S 2)/TOC ratio (defined as QI) was used as an indicator of the hydrocarbon potential. The QI, HI, and H/C ratio show a certain correlation, all increasing accordingly. The QI of the samples analyzed in this study is approximately 100–380 (mgHC/gTOC), similar to that of most humic coals for oil and gas generation. Samples with R o value lower than 0.55% always show significant variation in their HI, ranging from 80 to 520 mgHC/gTOC. It is inferred that hydrocarbon potential started from R o 0.55% and atomic H/C ratio 1.1 in this study.  相似文献   

13.
Organic-rich samples derived from a Middle Cambrian Formation in the Georgina Basin, and from the Middle Proterozoic of the McArthur Basin in northern and central Australia, yielded alginite ranging from immature oil shale material to overmature residue. A maturation scale has been developed based on the thermal evolution of alginite as determined from reflectance and fluorescence. The coalification path of alginite is marked by jumps in contrast to the linear path of wood-derived vitrinite. Six zones have been recognised, ranging from undermature (zone I), through the mature (zones II/III), followed by a stable stage of no change (zone IV) to the overmature (zones V and VI). The onset of oil generation in alginite as evident from the present study is at 0.3% Ro Alg. and is expressed in a change of fluorescence from yellow to brown, and a coalification jump from 0.3 to 0.6% Ro of Alg. In many boreholes zone III can be distinguished between 0.6 and 0.8% Ro of Alg. where subsequent oil generation occurs. Zones II and III represent the oil window.A zone of little or no change designated zone IV, at of alginite follows zones II/III. A marked coalification jump characterises zone V, where a pronounced change in reflectance occurs to >1.0% Ro Alg., signifying peak gas generation. The border of oil preservation lies at the transition of zone V and VI, at 1.6% Ro Alg. In zone VI gas generation only occurs.Comparison of reflectance results with experimental and geochemical pyrolysis data supports high activation energies for hydrocarbon generation from alginite, and therefore a later onset of oil generation than other liptinite macerals (i.e. cutinite, exinite, resinite) as well as a narrow oil window.Transmission electron microscopy (TEM) confirms that alginite does not go through a distinct intermediate stage but that the percentage of unreacted organic matter decreases as maturation proceeds. A clear distinction can be made in TEM between immature alginite, alginite after oil generation, and alginite residue following gas generation. Alginite beyond 1.6% Ro acquires very high densities and the appearance of inertinite in TEM.Bitumens/pyrobitumens make a pronounced contribution to the organic matter throughout the basins and have been shown to effect pyrolysis results by suppressing Tmax. The bitumens/pyrobitumens have been divided into four groups, based on their reflectance and morphology, which in turn appears to be an expression of their genetic history. Their significance is in aiding the understanding of the basins' thermal history, and the timing of oil and gas generation.  相似文献   

14.
Immature vitrinite samples from a Miocene lignite seam of western Germany (H/C = 1.14, O/C = 0.41) and alginite concentrates from a Tasmanite deposit of Australia (H/C = 1.60, O/C = 0.10) were pyrolyzed in a stream of argon at heating rates of 0.1 and 2.0°C/min up to temperatures varying from 200 to 670°C. The solid maceral residues were subjected to elemental and microscopical analysis and studied by IR and 13C CP/MAS NMR spectroscopy with respect to structural modifications.The maximum pyrolytic weight loss amounts to 60% of the initial organic matter in the case of vitrinite and to 85% for alginite, the onset of degradation reactions being shifted to higher temperatures with increasing rate of heating. Both infrared and NMR spectra of the vitrinite samples indicate a rapid decomposition of the cellulose component upon heating whereas lignin related structures such as aromatic ether linkages remain remarkably stable. The main hydrocarbon release from vitrinite occurs at very early evolution stages (Tmax = 296°C, Rm = 0.20% at 0.1°C/min; Tmax = 337°C, Rm = 0.23 at 2.0°C/min). Hydrocarbon generation from alginite requires higher temperatures (Tmax = 388 and 438°C) and is completed within a distinctly narrower temperature range.The pronounced increase of vitrinite reflectance between 350 and 670°C seems to be associated with a rather time-consuming reorganization of the residual organic material. The concomitant growth of polyaromatic units is illustrated by the increasing intensity ratio of the aromatic ring stretching vibration bands at 1600 and 1500 cm−1. These reactions are moreover marked by increasing loss of phenolic oxygen and by increasing conversion of aliphatic carbon into fixed aromatic carbon.  相似文献   

15.
Upper Triassic to Middle Jurassic coals from the Alborz region of northern Iran were analyzed by reflected light-fluorescence microscopy and Rock Eval 6® pyrolysis to evaluate their regional rank variation, degree of hydrothermal alteration, and petroleum generative potential. The coal ranks in the region range from a low of 0.69%RoR in the Glanddeh-Rud area to a high of 1.02%RoR in the Gajereh area. Tmax (°C) values (Rock Eval 6 pyrolysis) also increase progressively with increasing vitrinite %Ro values, however Tmax is suppressed lower than would be expected for each rank ranging from 428 °C for the Glandeeh coal to 438 °C for the Gajereh coal. Tmax suppression may be caused by maceral composition and soluble organics within the coal. Moderately high hydrogen indices, persistent and oily exudations from the coals during UV exposure, and traces of hydrocarbon fluid inclusions suggest that liquid petroleum was likely generated within some of the coals.  相似文献   

16.
This study provides coal quality, petrological, palynological and geochemical (Rock Eval) data on Permian coal seams and associated shales and mudstones of the Karoo Supergroup of the Songwe-Kiwira Coalfield, Tanzania. The coal seams, which have a cumulative thickness of 6.80 m, occur in the shale–coal–sandstone facies of the Mchuchuma Formation of Artinskian to Kungurian(?) age.Coal quality data (calorific values, volatile matter contents) and vitrinite reflectances indicate high volatile C bituminous to high volatile A bituminous coals, having relatively high ash yields (22–49 wt.%) and highly variable sulphur contents (0.17–9.2 wt.%). They could be used to fuel small-scale power generation units thereby providing electricity to nearby towns and villages. Also, the coals could be used as a substitute for wood, which is becoming increasingly scarce. In rural Tanzania, charcoal is still the main energy source for cooking, and wood is used extensively in brick kilns and for making roofing tiles.Petrological analysis indicated that the coals are dominated by dull to banded dull lithotypes, with seams at the base of the Mchuchuma Formation enriched in inertinite macerals (up to 83 vol.%), whereas up-section vitrinite contents increase. Palynological analyses indicated that the assemblage in the lower Mchuchuma Formation (Scheuringipollenites assemblage) is dominated by trilete spores, whereas in the remainder of the section, non-taeniate disaccates dominate (Scheuringipollenites–Protohaploxypinus assemblage). Facies critical macerals suggest for most seams a marsh/wet forest swamp depositional setting, which is consistent with the palynological data.Rock Eval analyses indicate type II/III kerogen, with Tmax (°C) values ranging from 426 to 440, corresponding to the early stage of hydrocarbon generation. Thermal Alteration Indices (2 to 2+) and vitrinite reflectance levels (0.60–0.83 Ro (%) support the Rock Eval maturity assessment, and despite the predominance of terrestrial-derived organic matter, there is evidence of oil generation and expulsion in the form of cavity and fracture filling exsudatinite.  相似文献   

17.
Suberinite, and subereous components of amorphous nature, comprise largely unrecognized, proficient sources of liquid hydrocarbons. Due to difficulties in recognizing the presence of subereous components and suberinite in organic sediments, the contributions of these liptinitic components to the organic input of source rocks are easily underestimated. Severe chemical alterations of suberinite in the vitrinite reflectance range of Ro = 0.35–0.60% are demonstrated. Organic geochemical data, obtained from samples subjected to natural maturation, reveal that subereous components/suberinite undergoes early thermal degradation to generate large amounts of hydrocarbons below Ro = 0.60%. Data obtained from laboratory maturation of immature, suberinite-rich coals indicate that about 50% of the potential of suberinite for generating C12+ hydrocarbons has already been exhausted during natural maturation of the samples, prior to the onset of the traditionally defined “oil window”. The present data (a) contradict the assumption that suberinite is mainly sourced by selective preservation/enrichment of a stable, highly aliphatic biopolymer, i.e. “suberan” and (b) suggest that suberinite contains appreciable amounts of aliphatic and aromatic moieties which are released at low thermal stress.  相似文献   

18.
A unique Upper Permian coal, Leping coal, is widely distributed in South China. The coal samples studied in the paper were collected from two mines in the Shuicheng coalfield of Guizhou Province, southwest China. The geochemical works including coal petrography, maceral content, Rock–Eval pyrolysis, and kinetic modelling of hydrocarbon-generating have been carried out on whole coal and individual macerals. The higher contents of volatile matter, elemental hydrogen, and tar yield, and the high hydrocarbon generation potential of the Leping coals are attributed to their high content of “barkinite”, a special liptinite maceral.The hydrocarbon generation potential of “barkinite” (S2=287 mg/g, hydrogen index (HI)=491 mg/g TOC) is greater than that of vitrinite (S2=180 mg/g, HI=249 mg/g TOC), and much higher than that of fusinite (S2=24 mg/g, HI=35 mg/g TOC). At the same experimental conditions, “barkinite” has a higher threshold and a narrower “oil window” than those of vitrinite and fusinite, and consequently, can generate more hydrocarbons in higher coalification temperature and shorter geological duration. Data from the activation energy distributions indicate that “barkinite” has a more homogenous chemical structure than that of vitrinite and fusinite. The above-mentioned characteristics are extremely important for exploring hydrocarbon derived from the Leping coals in South China.  相似文献   

19.
A systematic investigation of the petroleum exploratory well N-13 within the Huangqiao region, Lower Yangtze Basin, East China, has been carried out using multiple analytical techniques of organic geochemistry. The past occurrence of a thermal event has been recognized based on changes in optical vitrinite reflectance (Ro), pyrolysis peak temperature (Tmax) and chemical hydrogen index (HI), potential degradation rate (D), the atomic H/C ratio and dimethylphenanthrene ratios (DPR, DPR1 and DPR2) in the sedimentary rocks. The geological significance of this thermal event is discussed in this paper.  相似文献   

20.
The oil-generating potential of coals and other organic-rich sediments from the Late Oligocene–Early Miocene Nyalau Formation, the offshore extension of which is believed to be a major source rock, is evaluated. Coals of the Nyalau Formation are typically dominated by vitrinite, with moderate and low amounts of exinite and inertinite, respectively. Significant amounts of clay minerals are present in these coals and those containing between 15 to 65% mineral matter by volume are termed carbargilite. The samples analysed range from sub-bituminous to high-volatile bituminous rank, possessing vitrinite reflectance in the range 0.42% to 0.72%. Tmax values range from 425°–450°C which is in good agreement with vitrinite reflectance data. Good oil-generating potential is anticipated from these coals and carbargilites with moderate to rich exinite content (15–35%). This is supported by their high hydrogen indices of up to 400 mgHC/gTOC, Py–GC (S2) pyrograms with n-alkane/alkene doublets extending beyond nC30, and their being in the early to mid-mature oil-window range. Petrographically, the most significant evidence of the oil-generating potential of these coals is the generation of petroleum-like materials (exsudatinite) visible under the microscope. Exsudatinite is a secondary maceral, commonly considered to represent the very beginning of oil generation in coal, which is shown here to also have an important role to play in hydrocarbon expulsion. The precursor of exsudatinite in these coals is the maceral bituminite which readily expels or mobilizes to hydrocarbon-like material in the form of oil smears and/or exsudatinite as observed under the microscope. The maceral bituminite is considered to play a major generative role via early exsudatinite generation, which is considered to facilitate the overall expulsion process in coaly source rocks.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号