共查询到20条相似文献，搜索用时 515 毫秒
1.
《国际泥沙研究》2016,(3):264-270
The functions of the diversion channel are usually disturbed by sediment erosion and deposition. Con-sidering the effects of unsaturated sediment flow and narrowed cross section the diversion channel is enormously eroded. The discharge capacity, however, is deteriorated for the local deposition which lessens the water depth to satisfy the minimum navigable flow rate. In this study, the alternative diversion channel with unsaturated sediment flow at Hanjiang River, China, was taken as an example. The impacts of bed morphology for flood events and normal flow conditions were analyzed. The results show that the consideration of bed morphology is essential to design the diversion channel. Even for the unsaturated and eroded channel, the local deposition can reduce the water depth and restrict the navigable requirement under normal flow conditions. 相似文献
2.
Bed material transport at river bifurcations is crucial for channel stability and downstream geomorphic dynamics. However, measurements of bed material transport at bifurcations of large alluvial rivers are difficult to make, and standard estimates based on the assumption of proportional partitioning of flow and bedload transport at bifurcations may be erroneous. In this study, we employed a combined approach based on observed topographic change (erosion/deposition) and bed material transport predicted from a one-dimensional model to investigate bed material fluxes near the engineering-controlled Mississippi-Atchafalaya River diversion, which is of great importance to sediment distribution and delivery to Louisiana's coast. Yang's (1973) sediment transport equation was utilized to estimate daily bed material loads upstream, downstream, and through the diversion during 2004–2013. Bathymetric changes in these channels were assessed with single beam data collected in 2004 and 2013. Results show that over the study period, 24% of the Mississippi River flow was diverted into the Atchafalaya River, while the rest remained in the mainstem Mississippi. Upstream of the diversion, the bed material yield was predicted to be 201 million metric tons (MT), of which approximately 35 MT (i.e., 17%) passed through the bifurcation channel to the Atchafalaya River. The findings from this study reveal that in the mainstem Mississippi, the percentage of bed material diversion (83%) is larger than the percentage of flow diversion (76%); Conversely, the diversion channel receives a disproportionate amount of flow (24%) relative to bed material supply (17%). Consequently, severe bed scouring occurred in the controlled Outflow Channel to the Atchafalaya River, while riverbed aggradation progressed in the mainstem Mississippi downstream of the diversion structures, implying reduced flow capacity and potential risk of a high backwater during megafloods. The study demonstrates that Yang's sediment transport equation provides plausible results of bed material fluxes for a highly complicated large river diversion, and that integration of the sediment transport equation with observed morphological changes in riverbed is a valuable approach to investigate sediment dynamics at controlled river bifurcations. 相似文献
3.
Gravel-bed rivers characteristically exhibit shallow riffles in wide sections and deeper pools where the channel becomes constricted and narrow. While rivers can adjust to changing flow and sediment supply through some combination of adjustments of channel slope, bed-surface sorting, and channel shape, the degree to which riffle-pools may adopt these changes in response to changing flows and sediment supplies remains unclear. This article presents results from a flume experiment investigating how constant- and variable-width channels adjust their morphology in response to changing flow and increased sediment supply. Two flume geometries were used: (1) constant-width and (2) variable-width, characterized by a sinusoidal pattern with a mean width equal to that of the first channel. The variable-width channel developed bed undulations in phase with the width, representing riffle-pools. The experiment consisted of three phases for each flume geometry: (1) steady flow, constant sediment supply; (2) unsteady flow, constant sediment supply; and (3) unsteady flow, doubled sediment supply. Unsteady flow was implemented in the form of repeated symmetrical stepped hydrographs, with a mean discharge equal to that in the steady flow phase. In all phases the bed and sediment supply were composed of a sand/gravel mixture ranging from 1 to 8 mm. In both the straight and variable-width channels, transitioning from steady flow to repeated hydrographs did not result in significant changes in bed morphology. The two channel geometries had different responses to increased sediment supply: the slope of the straight channel increased nearly 40%, while the variable-width channel reduced the relief between bars and pools and decreased the variability in cross-sectional elevation with a slight slope increase. Bar-pool relief varied with repeat discharge hydrographs. Pool elevation changed twice the distance of bar elevations, emphasizing the relevance of pool scour for riffle-pool self-maintenance in channels with width variations. 相似文献
4.
Previous studies of alluvial rivers have shown that channel patterns form a continuum controlled by interactions among factors such as gradient, discharge, sediment size, and bank strength. Data from channels in the permanent wetlands of the Okavango Delta add to these ?ndings by focusing on pattern transitions in channels with banks formed by sedges and grasses that are rooted in peat and underlain by unconsolidated sediment. Channels are well de?ned, and transport ?ne–medium sand as bedload between the vertical, vegetation‐lined banks. Water depths, velocities, grain sizes, and bankline vegetation do not vary signi?cantly or systematically downstream, but the permeable banks allow water to leak from the channels, contributing to an overall downstream decrease in discharge and width. In addition, as the Okavango River ?ows from the <12 km wide ‘Panhandle’ and splits into distributaries in the broader ‘Fan’, valley gradient steepens by c. 60 per cent. These downstream changes result in channel pattern adjustments. In the Panhandle, the Okavango River is a relatively wide (c. 30–100 m), actively meandering, sinuous channel (P > 2·0), but further downstream in the Fan, the narrower (<40 m) distributaries follow laterally stable, less sinuous (‘straight’) courses (P < 1·75). Some channel pattern discrimination diagrams based on simple indices of gradient, discharge, sediment size or stream power are inadequate for analysing the meandering–straight transition in the Okavango but Parker's (1976) approach, based on ratios of depth–width and slope–Froude number, accurately characterizes the transition. Our ?eld observations, combined with the results from previous experimental studies, suggest that in relatively wide channels (w/d > 10), thalweg meandering results in scour of the unconsolidated sediment at the bank base, leading to undermining and collapse of the vegetation, and to slow meander migration. However, as channels narrow downstream (w/d < 10) with discharge losses, proportionally increasing sidewall drag exerted by bankline vegetation suppresses thalweg meandering and bank scour, and channels follow stable, less sinuous courses. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
5.
Subglacial water flow drives the excavation of a variety of bedrock channels including tunnel valleys and inner gorges. Subglacial floods of various magnitudes – events occurring once per year or less frequently with discharges larger than a few hundred cubic metres per second – are often invoked to explain the erosive power of subglacial water flow. In this study we examine whether subglacial floods are necessary to carve bedrock channels, or if more frequent melt season events (e.g. daily production of meltwater) can explain the formation of substantial bedrock channels over a glacial cycle. We use a one‐dimensional numerical model of bedrock erosion by subglacial meltwater, where water flows through interacting distributed and channelized drainage systems. The shear stresses produced drive bedrock erosion by bed‐ and suspended‐load abrasion. We show that seasonal meltwater discharge can incise an incipient bedrock channel a few tens of centimetres deep and several metres wide, assuming abrasion is the only mechanism of erosion, a particle size of D=256 mm and a prescribed sediment supply per unit width. Using the same sediment characteristics, flood flows yield wider but significantly shallower bedrock channels than seasonal meltwater flows. Furthermore, the smaller the shear stresses produced by a flood, the deeper the bedrock channel. Shear stresses produced by seasonal meltwater are sufficient to readily transport boulders as bedload. Larger flows produce greater shear stresses and the sediment is carried in suspension, which produces fewer contacts with the bed and less erosion. We demonstrate that seasonal meltwater discharge can excavate bedrock volumes commensurate with channels several tens of metres to a few hundred metres wide and several tens of metres deep over several thousand years. Such simulated channels are commensurate with published observations of tunnel valleys and inner gorges. Copyright © 2018 John Wiley & Sons, Ltd. 相似文献
6.
The upper part of the Huanghe (Yellow River) drainage basin supplies 50–60% of the annual water discharge and only 10% of the total river sediment load, while the middle reaches contribute 30–40% of the water flow and 90% of the annual sediment load, because of severe erosion over the Loess Plateau. Large variations in both annual water discharge and sediment load occur in the Huanghe. Heavy sedimentation in the lower reaches of the channel makes the river bed aggrade several centimetres per year. Of the suspended sediment in the river, 90–95% is deposited in the lower part of the river course and in the coastal shallow water area; less than 5–10% escapes from Laizhou Bay and enters the Central Bohai and/or North Huanghai (Yellow Sea). The active delta complex now propagates seawards at a mean rate of 42 km2 year−1. 相似文献
7.
In mixed bedrock–alluvial rivers, the response of the system to a flood event can be affected by a number of factors, including coarse sediment availability in the channel, sediment supply from the hillslopes and upstream, flood sequencing and coarse sediment grain size distribution. However, the impact of along-stream changes in channel width on bedload transport dynamics remains largely unexplored. We combine field data, theory and numerical modelling to address this gap. First, we present observations from the Daan River gorge in western Taiwan, where the river flows through a 1 km long 20–50 m wide bedrock gorge bounded upstream and downstream by wide braidplains. We documented two flood events during which coarse sediment evacuation and redeposition appear to cause changes of up to several metres in channel bed elevation. Motivated by this case study, we examined the relationships between discharge, channel width and bedload transport capacity, and show that for a given slope narrow channels transport bedload more efficiently than wide ones at low discharges, whereas wider channels are more efficient at high discharges. We used the model sedFlow to explore this effect, running a random sequence of floods through a channel with a narrow gorge section bounded upstream and downstream by wider reaches. Channel response to imposed floods is complex, as high and low discharges drive different spatial patterns of erosion and deposition, and the channel may experience both of these regimes during the peak and recession periods of each flood. Our modelling suggests that width differences alone can drive substantial variations in sediment flux and bed response, without the need for variations in sediment supply or mobility. The fluctuations in sediment transport rates that result from width variations can lead to intermittent bed exposure, driving incision in different segments of the channel during different portions of the hydrograph. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd 相似文献
8.
Proglacial suspended sediment transport was monitored at Haut Glacier d'Arolla, Switzerland, during the 1998 melt season to investigate the mechanisms of basal sediment evacuation by subglacial meltwater. Sub‐seasonal changes in relationships between suspended sediment transport and discharge demonstrate that the structure and hydraulics of the subglacial drainage system critically influenced how basal sediment was accessed and entrained. Under hydraulically inefficient subglacial drainage at the start of the melt season, sediment availability was generally high but sediment transport increased relatively slowly with discharge. Later in the melt season, sediment transport increased more rapidly with discharge as subglacial meltwater became confined to a spatially limited network of channels following removal of the seasonal snowpack from the ablation area. Flow capacity is inferred to have increased more rapidly with discharge within subglacial channels because rapid changes in discharge during highly peaked diurnal runoff cycles are likely to have been accommodated largely by changes in flow velocity. Basal sediment availability declined during channelization but increased throughout the remainder of the monitored period, resulting in very efficient basal sediment evacuation over the peak of the melt season. Increased basal sediment availability during the summer appears to have been linked to high diurnal water pressure variation within subglacial channels inferred from the strong increase in flow velocity with discharge. Basal sediment availability therefore appears likely to have been increased by (1) enhanced local ice‐bed separation leading to extra‐channel flow excursions and[sol ]or (2) the deformation of basal sediment towards low‐pressure channels due to a strong diurnally reversing hydraulic gradient between channels and areas of hydraulically less‐efficient drainage. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
9.
In this paper,the evolutions of flow pattern and sediment transportation at a 90° open-channel confluence with different discharge ratios (q*) of the tributary flow to the total flow were studied.The e... 相似文献
10.
G.M. Tarekul ISLAM M.R. KABIR Ainun NISHAT Institute of Flood Control Drainage Research Bangladesh University of Engineering Technology Dhaka Bangladesh E-mail: tarek@ifcdr.buet.ac.bd Department of Water Resources Engineeri 《国际泥沙研究》2002,17(2)
1 INTRODUCTION Bifurcations are typical features in alluvial rivers as well as in estuaries. In braided rivers confluence and bifurcation occur regularly (Fig.1). A bifurcation occurs when a river splits into two branches (Fig. 2). This happens when a middle bar forms in a channel or a distributary carries flow from the main river. In estuaries when the direction of tidal flow turns around an island, a confluence becomes bifurcation and vice versa. A braided river in the upstream end o… 相似文献
11.
Larry Syu-Heng Lai Joshua J. Roering Noah J. Finnegan Rebecca J. Dorsey Jiun-Yee Yen 《地球表面变化过程与地形》2021,46(13):2671-2689
The incision rate and steepness of bedrock channels depend on water discharge, uplift rate, substrate lithology, sediment flux, and bedload size. However, the relative role of these factors and the sensitivity of channel steepness to rapid (>1 mm yr−1) uplift rates remain unclear. We conducted field and topographic analyses of fluvial bedrock channels with varying channel bed lithology and sediment source rock along the Coastal Range in eastern Taiwan, where uplift rates vary from 1.8 to 11.8 mm yr−1 and precipitation is relatively consistent (1.5–2.7 m yr−1), to evaluate the controls on bedrock channel steepness. We find that channel steepness is independent of rock uplift rate and annual precipitation but increases monotonically with sediment size and substrate strength. Furthermore, in reaches with uniform substrate lithology (mudstone and flysch), channel steepness systematically varies with sediment source rock but not with channel width. When applied to our data, a mechanistic incision model (saltation-abrasion model) suggests that the steepness of Coastal Range channels is set primarily by coarse-sediment supply. We also observe that larger particles are mainly composed of resistant lithologies derived from volcanic rocks and conglomerates. This result implies that hillslope bedrock properties in the source area exert a dominant control on the steepness of proximal channels through coarse-sediment production in this setting. We propose that channel steepness may be insensitive to uplift rate and flow discharge in fast-uplifting landscapes where incision processes are set by coarse sediment size and supply. Models assuming a proportionality between incision rate and basal shear stress (stream power) may not fully capture controls on fluvial channel profiles in landslide-dominated landscapes. Processes other than channel steepening, such as enhanced bedload impacts and debris-flow scour, may be required to balance rock uplift and incision in these transport-limited systems. 相似文献
12.
William L. Graf 《地球表面变化过程与地形》1983,8(2):125-139
A review of 112 years of change in the channel of the Salt River, central Arizona, U.S.A., shows that this arid-region river has a main-flow channel that has migrated laterally up to 1.6 km (1 mi) in response to floor events. Maps showing locational probabilities indicate that along the channel zones of relative locational stability alternate with zones of relative instability at a 3.2 km (2 mi) interval. Construction of upstream reservoirs has reduced sediment input into the main river but has not controlled floods. The channel width has not changed except for moderate fluctuations around mean values; the main-flow channel has incised approximately 6 m (20 ft) over most of the 48 km (30 mi) study reach during six recent floods. Gradient has remained unchanged. During floods bed material was mobilized to a depth below the original bed level that was greater than the height of the water surface above the original bed. Calculations based on tractive force indicate a threshold discharge of instability that is equal to the flow with a five-year return interval. The river exhibits remarkable stability with respect to gradient and sinuosity, irrespective of water and sediment discharges, but horizontal channel location exhibited selective instability. Over the record period of more than a century, the channel appears not to have been in equilibrium considering geometry, discharge, and sediment. 相似文献
13.
Evolution of bed material mobility and bedload grain size distributions under a range of discharges is rarely observed in braiding gravel-bed rivers. Yet, the changing of bedload grain size distributions with discharge is expected to be different from laterally-stable, threshold, channels on which most gravel bedload theory and observation are based. Here, simultaneous observations of flow, bedload transport rate, and morphological change were made in a physical model of a gravel-bed braided river to document the evolution of grain size distributions and bed mobility over three experimental event hydrographs. Bedload transport rate and grain size distributions were measured from bedload samples collected in sediment baskets. Morphological change was mapped with high-resolution (~1 mm precision) digital elevation models generated from close-range digital photogrammetry. Bedload transport rates were extremely low below a discharge equivalent to ~50% of the channel-forming discharge (dimensionless stream power ~70). Fractional transport rates and plots of grain size distributions indicate that the bed experienced partial mobility at low discharge when the coarsest grains on the bed were immobile, weak selective mobility at higher discharge, and occasionally near-equal mobility at peak channel-forming discharge. The transition to selective mobility and increased bedload transport rates coincided with the lower threshold for morphological change measured by the morphological active depth and active width. Below this threshold discharge, active depths were of the order of D90 and active widths were narrow (< 3% of wetted width). Above this discharge, both increased so that at channel-forming discharge, the active depth had a local maximum of 9D90 while active width was up to 20% of wetted width. The modelled rivers approached equal mobility when rates of morphological change were greatest. Therefore, changes in the morphological active layer with discharge are directly connected to the conditions of bed mobility, and strongly correlated with bedload transport rate. © 2018 John Wiley & Sons, Ltd. 相似文献
14.
Many lowland fluvial systems are suspected to possess a morphological legacy from a long history of channel modifications as a consequence of limited energy and sediment supply to facilitate recovery. We explore the extent of such modifications using a regionally extensive dataset of physical habitat surveys compiled by non-specialist surveyors. Representative photographs for each surveyed site were used to quality check channel width, depth and bed grain size information derived from Modular River Physical (MoRPh) surveys. Following checking, 1659 surveys were retained for analysis from alluvial sites, almost entirely in England. The photographs were also inspected for evidence of clear ‘overdeepening’ that would preclude frequent overtopping of the lower bank top. Results indicated that almost one-third of the sites were overdeepened, that width-to-depth ratios defined using the active bed width showed stronger discrimination of overdeepening than bankfull width, that highly statistically significant identification of overdeepened channels was possible in channels up to 10 m wide and with only minimal differences attributable to channel bed materials. Stepwise regression analysis estimated relationships between channel width-to-depth ratios and channel size for overdeepened and non-overdeepened channels. We demonstrate that large data sets collected by numerous non-specialist surveyors can, with careful filtering, generate statistically robust results of geomorphological value over areas larger than is otherwise practicable. Furthermore, we reveal a notable legacy of overdeepening in the analysed lowland rivers, which presents a significant ‘hydromorphological’ management challenge. 相似文献
15.
Hydro‐morphodynamic evolution in a 90° movable bed discordant confluence with low discharge ratio 
下载免费PDF全文
下载免费PDF全文 Sebastián Guillén‐Ludeña Mário J. Franca António H. Cardoso Anton J. Schleiss 《地球表面变化过程与地形》2015,40(14):1927-1938
Confluences with low discharge and momentum ratios, where narrow steep tributaries with high sediment load join a wide low‐gradient main channel that provides the main discharge, are often observed in high mountain regions such as in the upper‐Rhone river catchment in Switzerland. Few existing studies have examined the hydro‐morphodynamics of this type of river confluence while considering sediment discharge in both confluent channels. This paper presents the evolution of the bed morphology and hydrodynamics as observed in an experimental facility with a movable bed. For that purpose, one experiment was carried out in a laboratory confluence with low discharge and momentum ratios, where constant sediment rates were supplied to both flumes. During the experiment, bed topography and water surface elevations were systematically recorded. When the bed topography reached a steady state (so‐called equilibrium) and the outgoing sediment rate approximated the incoming rate, flow velocity was measured at 12 different points distributed throughout the confluence, and the grain size distribution of the bed surface was analyzed. Typical morphodynamic features of discordant confluences such as a bank‐attached bar and a flow deflection zone are identified in this study. Nevertheless, the presence of a marked scour hole in the discordant confluence and distinct flow regimes for the tributary and main channel, differ from results obtained in previous studies. Strong acceleration of the flow along the outer bank of the main channel is responsible for the scour hole. This erosion is facilitated by the sediment discharge into the confluence from the main channel which inhibits bed armoring in this region. The supercritical flow regime observed in the tributary is the hydrodynamic response to the imposed sediment rate in the tributary. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
16.
Jiongxin Xu 《地球表面变化过程与地形》2004,29(5):645-657
A comparison has been made between the hydraulic geometry of sand‐ and gravel‐bed rivers, based on data from alluvial rivers around the world. The results indicate a signi?cant difference in hydraulic geometry among sand‐ and gravel‐bed rivers with different channel patterns. On this basis, some diagrams for discrimination of meandering and braided channel patterns have been established. The relationships between channel width and water discharge, between channel depth and water discharge, between width–depth ratio and water discharge and between channel slope and water discharge can all be used for channel pattern discrimination. The relationship between channel width and channel depth can also be used for channel pattern discrimination. However, the accuracy of these relationships for channel pattern discrimination varies, and the depth–discharge relationship is a better discriminator of pattern type than the classic slope–discharge function. The cause for this difference has been explained qualitatively. To predict the development of channel patterns under different natural conditions, the pattern discriminator should be searched on the basis of independent or at least semi‐independent variables. The relationship between stream power and bed material grain size can be used to discriminate channel patterns, which shows a better result than the discriminator using the slope–discharge relationship. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
17.
Three‐dimensional numerical modeling of the Bulle effect: the nonlinear distribution of near‐bed sediment at fluvial diversions 下载免费PDF全文
下载免费PDF全文 The Bulle effect is a phenomenon in which a disproportionately higher amount of near‐bed sediment load at a fluvial diversion moves into the diverted channel, even for cases in which the proportion of water (with respect to the main flow) entering the diversion channel is relatively small. This phenomenon has wide‐ranging implications for both engineered and natural systems: from efficient design of channels to redirect water and sediment for reclaiming sinking deltas, designing navigational channels that do not need frequent dredging, to morphological evolution of river bifurcations. The first ever, and one of the most extensive set of experiments conducted to explore this phenomenon, were conducted by Bulle in 1926 . In the current study the experiments conducted by Bulle have been simulated using an open‐source, free‐surface finite‐element‐based hydrodynamic solver. The main objectives were to explore to what extent the complex phenomenon of the Bulle effect at the scale of a laboratory experiment can be simulated accurately using Reynolds‐averaged Navier–Stokes (RANS)‐based hydrodynamic solver, and to understand the details of the hydrodynamics that Bulle could not analyze through his experiments. The hydrodynamics captured by the simulations were found to match the observations made by Bulle through his experiments, and the distributions of sediment at the diversion predicted by the numerical simulations were found to match the general trend observed in the laboratory experiments. The results from the numerical simulations were also compared with existing one‐dimensional models for sediment distribution at bifurcations, and the three‐dimensional numerical model was found to perform appreciably better. This is expected due to the complex flow features at the diversion, which can only be captured satisfactorily using a three‐dimensional hydrodynamic model. Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
18.
Influence of junction angle on three‐dimensional flow structure and bed morphology at confluent meander bends during different hydrological conditions 下载免费PDF全文
下载免费PDF全文 Recent field and modeling investigations have examined the fluvial dynamics of confluent meander bends where a straight tributary channel enters a meandering river at the apex of a bend with a 90° junction angle. Past work on confluences with asymmetrical and symmetrical planforms has shown that the angle of tributary entry has a strong influence on mutual deflection of confluent flows and the spatial extent of confluence hydrodynamic and morphodynamic features. This paper examines three‐dimensional flow structure and bed morphology for incoming flows with high and low momentum‐flux ratios at two large, natural confluent meander bends that have different tributary entry angles. At the high‐angle (90°) confluent meander bend, mutual deflection of converging flows abruptly turns fluid from the lateral tributary into the downstream channel and flow in the main river is deflected away from the outer bank of the bend by a bar that extends downstream of the junction corner along the inner bank of the tributary. Two counter‐rotating helical cells inherited from upstream flow curvature flank the mixing interface, which overlies a central pool. A large influx of sediment to the confluence from a meander cutoff immediately upstream has produced substantial morphologic change during large, tributary‐dominant discharge events, resulting in displacement of the pool inward and substantial erosion of the point bar in the main channel. In contrast, flow deflection is less pronounced at the low‐angle (36°) confluent meander bend, where the converging flows are nearly parallel to one another upon entering the confluence. A large helical cell imparted from upstream flow curvature in the main river occupies most of the downstream channel for prevailing low momentum‐flux ratio conditions and a weak counter‐rotating cell forms during infrequent tributary‐dominant flow events. Bed morphology remains relatively stable and does not exhibit extensive scour that often occurs at confluences with concordant beds. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
19.
Comprehensive empirical data of the response of unstable streams over a range of environmental conditions are unavailable. In this study, as a substitute for empirical data, a physically based numerical model of channel evolution is used in a range of numerical simulation experiments designed to predict the sensitivity of channel response to changes in control variables. The scope of the study is limited by the scope of the numerical model which applies to straight, sand-bed streams with cohesive bank materials that have been destabilized by sediment starvation and evolve towards equilibrium through bed degradation followed by channel widening. Results are presented for stable and unstable channel conditions. Stable channel depths are most sensitive to channel discharge, though the critical threshold shear stress for the entrainment of cohesive bank materials and discharge are both significant in determining the width. The sediment load, channel gradient, bank material cohesion, size of failed bank material aggregates and the initial bank height have sensitivities an order of magnitude smaller than discharge for both width and depth. Variations in bed material characteristics within the sand-size range are found to have little impact on simulated stable channel morphology. For unstable channels, the relative dominance of parameter sensitivities is examined in the context of an empirical-conceptual model of channel evolution proposed by Thorne and Osman (1988), to highlight the relationships between parameter dominance, time, and the processes and forms characterizing individual stages of channel evolution. Rates of change with time of width and depth sensitivity parameters for five tested independent variables (discharge, sediment supply, channel gradient, bank material cohesion and bed material size) are found to vary as a function of time, such that different stages of channel evolution are characterized by variations in the relative dominance of tested variables. The results support the hypothesis proposed by Thorne and Osman (1988) that the critical bank height required to initiate mass-wasting and widening may be regarded as a geomorphic threshold. 相似文献
20.
Maarten G. Kleinhans Kim M. Cohen Jantine Hoekstra Janneke M. IJmker 《地球表面变化过程与地形》2011,36(15):2011-2027
Rivers may dramatically change course on a fluvial plain. Such an avulsion temporarily leads to two active channels connected at a bifurcation. Here we study the effect of dynamic meandering at the bifurcation and the effect of channel width adjustment to changing discharge in both downstream branches on the evolution of a bifurcation and coexisting channels. As an example, we reconstructed the last major avulsion at the Rhine delta apex. We combined historical and geological data to reconstruct a slowly developing avulsion process spanning 2000 years and involving channel width adjustment and meandering at the bifurcation. Based on earlier idealised models, we developed a one‐dimensional model for long‐term morphodynamic prediction of upstream channel and bifurcates connected at the bifurcation node. The model predicts flow and sediment partitioning at the node, including the effect of migrating meanders at the bifurcation and channel width adjustment. Bifurcate channel width adaptation to changing discharge partitioning dramatically slows the pacing of bifurcation evolution because the sediment balance for width adjustment and bed evolution are coupled. The model further shows that meandering at the bifurcation modulates channel abandonment or enlargement periodically. This explains hitherto unrecognised reactivation signals in the sedimentary record of the studied bifurcation meander belts, newly identified in our geological reconstruction. Historical maps show that bifurcation migration due to meander bend dynamics increases the bifurcation angle, which increases the rate of closure of one bifurcate. The combination of model and reconstruction identifies the relevant timescales for bifurcation evolution and avulsion duration. These are the time required to fill one downstream channel over one backwater length, the time to translate one meander wavelength downstream and, for strong river banks, the adaptation timescale to adjust channel width. The findings have relevance for all avulsions where channel width can adjust to changing discharge and where meandering occurs. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献