首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Peat soils are heterogeneous, anisotropic porous media. Compared to mineral soils, there is still limited understanding of physical and solute transport properties of fen peat soils. In this study, we aimed to explore the effect of soil anisotropy on solute transport in degraded fen peat. Undisturbed soil cores, taken in vertical and horizontal direction, were collected from one drained and one restored fen peatland both in a comparable state of soil degradation. Saturated hydraulic conductivity (K s) and chemical properties of peat were determined for all soil cores. Miscible displacement experiments were conducted under saturated steady state conditions using potassium bromide as a conservative tracer. The results showed that (1) the K s in vertical direction (K sv) was significantly higher than that in horizontal direction (Ksh), indicating that K s of degraded fen peat behaves anisotropically; (2) pronounced preferential flow occurred in vertical direction with a higher immobile water fraction and a higher pore water velocity; (3) the 5% arrival time (a proxy for the strength of preferential flow) was affected by soil anisotropy as well as study site. A strong correlation was found between 5% arrival time and dispersivity, K s and mobile water fraction; (4) phosphate release was observed from drained peat only. The impact of soil heterogeneity on phosphate leaching was more pronounced than soil anisotropy. The soil core with the strongest preferential flow released the highest amount of phosphate. We conclude that soil anisotropy is crucial in peatland hydrology but additional research is required to fully understand anisotropy effects on solute transport.  相似文献   

2.
Our understanding of hydraulic properties of peat soils is limited compared with that of mineral substrates. In this study, we aimed to deduce possible alterations of hydraulic properties of peat soils following degradation resulting from peat drainage and aeration. A data set of peat hydraulic properties (188 soil water retention curves [SWRCs], 71 unsaturated hydraulic conductivity curves [UHCs], and 256 saturated hydraulic conductivity [Ks] values) was assembled from the literature; the obtained data originated from peat samples with an organic matter (OM) content ranging from 23 to 97 wt% (weight percent; and according variation in bulk density) representing various degrees of peat degradation. The Mualem‐van Genuchten model was employed to describe the SWRCs and UHCs. The results show that the hydraulic parameters of peat soils vary over a wide range confirming the pronounced diversity of peat. Peat decomposition significantly modifies all hydraulic parameters. A bulk density of approximately 0.2 g cm?3 was identified as a critical threshold point; above and below this value, macroporosity and hydraulic parameters follow different functions with bulk density. Pedotransfer functions based on physical peat properties (e.g., bulk density and soil depth) separately computed for bog and fen peat have significantly lower mean square errors than functions obtained from the complete data set, which indicates that not only the status of peat decomposition but also the peat‐forming plants have a large effect on hydraulic properties. The SWRCs of samples with a bulk density of less than 0.2 g cm?3 could be grouped into two to five classes for each peat type (botanical composition). The remaining SWRCs originating from samples with a bulk density of larger than 0.2 g cm?3 could be classified into one group. The Mualem‐van Genuchten parameter values of α can be used to estimate Ks if no Ks data are available. In conclusion, the derived pedotransfer functions provide a solid instrument to derive hydraulic parameter values from easily measurable quantities; however, additional research is required to reduce uncertainty.  相似文献   

3.
Solute leaching in unsaturated soil is influenced by the variability in hydraulic functions (water retention and conductivity) that govern the flow process. Variability in measured soil hydraulic functions of a coarse-, medium- and fine-textured soil group was quantified with the scaling theory of similar media. Solute leaching in these soils was calculated with Monte Carlo simulation assuming, successively, hydraulic conductivity, K, volumetric water content, 0, and pressure head, h, to be constant. In addition to variability in hydraulic functions, variability in the solute retardation factor was also taken into account. To examine this effect five solutes were considered: a conservative solute (chloride), a non-retarded solute subject to decay (nitrate), a retarded solute that does not decay (cadmium) and two organic solutes which are retarded but have different sorption and decay parameters (the pesticide atrazine and a chlorinated hydrocarbon). The numerical results obtained with Monte Carlo simulation were in a number of instances verified with analytical solutions. The three soil groups distinguished showed considerable differences in vulnerability for leaching of the five solutes, emphasizing the importance of the effect of variability in soil hydraulic functions when studying solute leaching. Numerical and analytical results showed good agreement. Therefore, in relatively simple situations analytical solutions are attractive. However, in complicated situations, analytical solutions are cumbersome and numerical solutions are the only realistic alternative.  相似文献   

4.
Although widely used in wetland hydrological studies, hydraulic conductivity (K) estimates from piezometer slug tests are often of questionable validity. Frequently, this is because insufficient attention is paid to the details of the test procedure. Further, in a potentially heterogeneous and anisotropic medium such as peat, the use of slug tests is prone to error. In this paper we address some of the methodological issues surrounding piezometer slug tests in peat. We compare slug test data with laboratory determinations of vertical and horizontal K obtained using a new method. Piezometers were installed at three depths in a floodplain fen peat in Norfolk, UK. Slug tests were initiated by both slug insertion and slug withdrawal, and repeat tests were conducted to examine the robustness of our K estimates. Most of the tests displayed departures from the log‐linear model of Hvorslev, the form of departure being consistent with compressible soil behaviour. The results suggest that insertion tests gave similar results to those initiated by withdrawal. Repeat testing showed that withdrawal data, in particular, gave highly reproducible normalized responses that were independent of the initial head. Values for K estimated using the slug tests were in the range 1 × 10−4 to 1·6 × 10−3 cm s−1, which is towards the upper end of the range reported for peats generally. Laboratory tests yielded similar values of K to those obtained from the slug tests. Although the laboratory tests showed that the peat was anisotropic, the K values generated by slug testing proved relatively good estimates of both vertical and horizontal K. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

5.
Evaporation from mosses and lichens can form a major component of the water balance, especially in ecosystems where mosses and lichens often grow abundantly, such as tundra, deserts and bogs. To facilitate moss representation in hydrological models, we parameterized the unsaturated hydraulic properties of mosses and lichens such that the capillary water flow through moss and lichen material during evaporation could be assessed. We derived the Mualem‐van Genuchten parameters of the drying retention and the hydraulic conductivity functions of four xerophilous moss species and one lichen species. The shape parameters of the retention functions (2.17 < n < 2.35 and 0.08 < α < 0.13 cm?1) ranged between values that are typical for sandy loam and loamy sand. The shapes of the hydraulic conductivity functions of moss and lichen species diverged from those of mineral soils, because of strong negative pore‐connectivity parameters (?2.840 < l < ?2.175) and low hydraulic conductivities at slightly negative pressure heads (0.016 < K0 < 0.280 cm/d). These K0 values are surprisingly low, considering that mosses are very porous. However, during evaporation, large pores and voids were air filled and did not participate in capillary water flow. Small K0 values cause mosses and lichens to be conservative with water during wet conditions, thus tempering evaporation compared to mineral soils. On the other hand, under dry conditions, mosses and lichens are able to maintain a moisture supply from the soil, leading to a higher evaporation rate than mineral soils. Hence, the modulating effect of mosses on evaporation possibly differs between wet and dry climates. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

6.
Testing infiltrometer techniques to determine soil hydraulic properties is necessary for specific soils. For a loam soil, the water retention and hydraulic conductivity predicted by the BEST (Beerkan Estimation of Soil Transfer parameters) procedure of soil hydraulic characterization was compared with data collected by more standard laboratory and field techniques. Six infiltrometer techniques were also compared in terms of saturated soil hydraulic conductivity, Ks. BEST yielded water retention values statistically similar to those obtained in the laboratory and Ks values practically coinciding with those determined in the field with the pressure infiltrometer (PI). The unsaturated soil hydraulic conductivity measured with the tension infiltrometer (TI) was reproduced satisfactorily by BEST only close to saturation. BEST, the PI, one‐potential experiments with both the TI and the mini disk infiltrometer (MDI), the simplified falling head (SFH) technique and the bottomless bucket (BB) method yielded statistically similar estimates of Ks, differing at the most by a factor of three. Smaller values were obtained with longer and more soil‐disturbing infiltration runs. Any of the tested infiltration techniques appears usable to obtain the order of magnitude of Ks at the field site, but the BEST, BB and PI data appear more appropriate to characterize the soil at some stage during a rainfall event. Additional investigations on both similar and different soils would allow development of more general procedures to apply infiltrometer techniques for soil hydraulic characterization. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

7.
Little is known about solute transport in peats, despite the obvious importance of solute transport on eco‐hydrological processes in both managed and natural peatlands. To address this lack of knowledge, we investigated solute transport processes in an agricultural fen peat using a conservative KBr tracer. The main aim of the study was to elucidate solute transport behaviour in general in this peat, with a more specific aim of investigating whether preferential or bypassing flow occurred. The tracer moved through the peat more rapidly than expected, and the pattern of movement showed clear evidence of plot‐scale bypassing flow. The data also provide evidence that bypassing flow occurs in pores at smaller scales. The implications of this study for management of wetland pastures in the Somerset Moors in south‐west England are discussed. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

8.
Anisotropy and heterogeneity of hydraulic conductivity (K) are suspected of greatly affecting rates and patterns of ground‐water seepage in peats. A new laboratory method, termed here the modified cube method, was used to measure horizontal and vertical hydraulic conductivity (Kh and Kv) of 400 samples of bog peat. The new method avoids many of the problems associated with existing field and laboratory methods, and is shown to give relatively precise measurements of K. In the majority of samples tested, Kh was much greater than Kv, indicating that the bog peat was strongly anisotropic. Log10Kh, log10Kv, and log10 (Kh/Kv) were found to vary significantly with depth, although none of the relationships was simple. We comment on the scale dependency of our measurements. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

9.
The hydraulic conductivity (K) of peat beneath the water table varies over short (annual) periods. Biogenic gas bubbles block pores and reduce K, and seasonal changes in the water table position cause peat deformation, altering peat pore size distribution. Although it has been hypothesized that both processes reduce K during warm dry summer conditions, temporal variations in K under field conditions have been explained previously by peat volume changes (strain) alone. We determine the effect of both controls on K by monitoring changes in gas content (Δγ), strain and K within a poor fen. Over the growing season, K decreased by an order of magnitude. In the near‐surface peat (0.3–0.7 m), this reduction is more strongly correlated with Δγ, providing the first field‐based evidence that biogenic gas bubbles reduce K. In the deeper peat (0.7–1.3 m), K is correlated principally with strain. However, causality is uncertain because of multicollinearity between strain and Δγ. To mitigate for multicollinearity, we took advantage of a peatland drainage experiment where the water table was artificially dropped at the beginning of the growing season, reducing correlations between strain and Δγ. Δγ remained the primary cause of K variations just beneath the water table at a depth of 0.5–0.7 m, although further down through the peat profile (0.7–1.2 m) changes in K were controlled by strain. We suggest that the larger pore structure of the poorly decomposed peat just below the water table is impacted less by volume changes than that of the more decomposed peat at depth. However, within this poorly decomposed peat, K is reduced by the high gas contents that result from higher rates of methane production. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

10.
Hydraulic thresholds for erosion of fourteen upland mineral and organic soils were determined in a hydraulic flume. These soils are from areas to be afforested in the United Kingdom. Some of the group are erosion resistant but others are susceptible to erosion once denuded of vegetation; for example, by preafforestation ploughing. These threshold data were required to calibrate a hydraulic model for effective design of preafforestation drainage networks on a variety of soils. However, simple field measures of soil properties indicative of erosion potential would be of value to the forestry industry for management purposes. Consequently, hydraulic threshold data were related by linear regression methods to basic soil properties, including organic content, grain size, bulk density, compression strength and penetration resistance. The investigation concluded that four peat soils are not eroded by clear water velocities up to 5·7 m s−1, although a mineral bedload might induce erosion at lesser current speeds. Penetration resistance is a good field indicator of the degree of humification of the peat soils. Although selected physical parameters contribute resistance to water erosion, an increased organic content is pre-eminent in reducing erosion susceptibility in both organic and mineral soils. Although compressive strength was not indicative of soil erodibility, field measurements of penetration resistance on a variety of soils could be related to hydraulic thresholds of erosion; albeit through the construction of discriminant functions interpolated by eye. Consequently, organic content (laboratory) or penetration resistance (field) might form the basis of classifying upland soils in terms of erodibility. Mineral soils differ widely in terms of their erodibility, so that subject to further consideration, the use of ploughing for forestry cultivation might be appropriate in wider circumstances than presently recommended by the Forests and Water Guidelines. Ploughing should be acceptable on deep peat providing the underlying mineral soil is not exposed in the bottom of the furrow, and furrows are not led from mineral soils on to deep peat. © 1997 John Wiley & Sons, Ltd.  相似文献   

11.
J. Holden  T. P. Burt 《水文研究》2003,17(6):1227-1237
A key parameter used in wetland hydrological and landform development models is hydraulic conductivity. Head recovery tests are often used to measure hydraulic conductivity, but the calculation techniques are usually confined to rigid soil theory. This is despite reports demonstrating the misapplication of rigid soil theory to non‐rigid soils such as peats. Although values of hydraulic conductivity calculated using compressible techniques have been presented for fenland peats, these data have never, to the authors' knowledge, been compared with such calculations in other peat types. Head recovery tests (slug withdrawal) were performed on piezometers at depths ranging from 10 to 80 cm from the surface on north Pennines blanket peats. Results were obtained using both rigid and compressible soil theories, thus allowing comparison of the two techniques. Compressible soil theory gives values for hydraulic conductivity that are typically a factor of five times less than rigid soil calculations. Hydraulic conductivity is often assumed to decrease with depth in upland peats, but at the study site in the northern Pennines it was not found to vary significantly with depth within the range of peat depths sampled. The variance within depth categories was not significantly different to the variance between depth categories showing that individual peat layers did not have characteristic hydraulic conductivity values. Thus, large lateral and vertical differences in hydraulic conductivity over short distances create problems for modelling but may help account for the high frequency of preferential flow pathways within what is otherwise a low matrix hydraulic conductivity peat. Hydraulic conductivity was found to vary significantly between sampling sites, demonstrating that hillslope‐ or catchment‐scale variability may be more important than plot‐scale variability. Values for compressibility of the peats are also reported. These generally decline with depth, and they also vary significantly between sampling sites. There are implications for the way in which measurements of hydraulic conductivity and other properties of blanket peat are interpreted, as the effects of environmental change in one part of a peat catchment may be very different to those in another. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

12.
Water and solute movement in a coarse-textured water-repellent field soil   总被引：6，自引：0，他引：6  
Unstable water flow in water-repellent unsaturated soils can significantly affect the processes of infiltration and soil water redistribution. A field experiment was carried out to study the effect of water-repellency on water and bromide movement in a coarse-textured soil in the southwestern part of The Netherlands. The field data were analyzed using a relatively simple numerical model based on the standard Richards' equation for unsaturated water flow and the Fickian-based convection-dispersion equation for solute transport. Water-repellency was accounted for by multiplying the water content and the unsaturated hydraulic conductivity of the soil with F, a factor equal to the volumetric fraction of soil occupied by preferential flow paths resulting from the unstable flow process. The good comparison of simulated and measured bromide concentrations suggests that the model provides a viable method for simulating unstable water flow in water-repellent soils.  相似文献   

13.
In organic soils, hydraulic conductivity is related to the degree of decomposition and soil compression, which reduce the effective pore diameter and consequently restrict water flow. This study investigates how the size distribution and geometry of air‐filled pores control the unsaturated hydraulic conductivity of peat soils using high‐resolution (45 µm) three‐dimensional (3D) X‐ray computed tomography (CT) and digital image processing of four peat sub‐samples from varying depths under a constant soil water pressure head. Pore structure and configuration in peat were found to be irregular, with volume and cross‐sectional area showing fractal behaviour that suggests pores having smaller values of the fractal dimension in deeper, more decomposed peat, have higher tortuosity and lower connectivity, which influences hydraulic conductivity. The image analysis showed that the large reduction of unsaturated hydraulic conductivity with depth is essentially controlled by air‐filled pore hydraulic radius, tortuosity, air‐filled pore density and the fractal dimension due to degree of decomposition and compression of the organic matter. The comparisons between unsaturated hydraulic conductivity computed from the air‐filled pore size and geometric distribution showed satisfactory agreement with direct measurements using the permeameter method. This understanding is important in characterizing peat properties and its heterogeneity for monitoring the progress of complex flow processes at the field scale in peatlands. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

14.
Coastal peatlands represent an interface between marine and terrestrial ecosystems; their hydrology is affected by salt and fresh water inflow alike. Previous studies on bog peat have shown that pore water salinity can have an impact on the saturated hydraulic conductivity (Ks) of peat because of chemical pore dilation effects. In this study, we aimed at quantifying the impact of higher salinities (up to 3.5% NaCl) on Ks of fen peat. Two experiments employing a constant‐head upward‐flow permeameter and differing in measurement and salinity change duration were conducted. Additionally, a third experiment to determine the impact of water salinity on the release of dissolved organic carbon (DOC) of the studied peat type was carried out. The results show a decrease of Ks with time, which does not depend on the water salinity but is differently shaped for different peat types. We assume pore clogging due to a conglomerate of physical, chemical, and biological processes, which rather depend on water movement rate and time than on water salinity. However, an increased water salinity did increase the DOC release. We conclude that salinity‐dependent behaviour of Ks is a function of peat chemistry and that for some peat types, salinity may only affect the DOC release without having a pronounced impact on water flow.  相似文献   

15.
The water retention curve (θ(ψ)), which defines the relationship between soil volumetric water content (θ) and matric potential (ψ), is of paramount importance in characterizing the hydraulic behaviour of soils. However, few methods are so far available for estimating θ(ψ) in undisturbed soil samples. We present a new design of TDR‐pressure cell (TDR‐Cell) for estimating θ(ψ) in undisturbed soil samples. The TDR‐Cell consists of a 50‐mm‐long and 50‐mm internal diameter stainless steel cylinder (which constitutes the outer frame of a coaxial line) attached to a porous ceramic disc and closed at the ends with two aluminium lids. A 49‐mm‐long and 3‐mm‐diameter stainless steel rod, which runs longitudinally through the centre of the cylinder, constitutes the inner rod of a coaxial TDR probe. The TDR‐Cell was used to determine the θ(ψ) curves of a packed sand and seven undisturbed soil samples from three profiles of agricultural soils. These θ(ψ) curves were subsequently compared to those obtained from the corresponding 2‐mm sieved soils using the pressure plate method. Measurements of bulk electrical conductivity, σa, as a function of the water content, σa(θ), of the undisturbed soil samples were also performed. An excellent correlation (R2 = 0·988) was found between the θ values measured by TDR on the different undisturbed soils and the corresponding θ obtained from the soil gravimetric water content. A typical bimodal θ(ψ) function was found for most of the undisturbed soil samples. Comparison between the θ(ψ) curves measured with the TDR‐Cell and those obtained from the 2‐mm sieved soils showed that the pressure plate method overestimates θ at low ψ values. The σa(θ) relationship was well described by a simple power expression (R2 > 0·95), in which the power factor, defined as tortuosity, ranged between 1·18 and 3·75. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

16.
Abstract

Wetting front instability (fingered flow) accelerates solute transport through the unsaturated zone to the groundwater table. Whether fingers widen or dissipate close to the groundwater is unclear. Water flow in a two-dimensional artificial capillary fringe below a dry layer exhibiting fingered flow was investigated. The flow diverged strongly in the wet soil, suggesting that fingers dissipate. Expressions for the finger radius in dry and wet soil were combined and adapted to a soil hydraulic property parameterization popular in numerical modelling. The modified equation provided finger radii for soils in humid and arid climates. The fingers in the arid soil were excessively wide. The finger radii were used to model solute transport, assuming fingers dissipated in the subsoil. Modelling was cumbersome for the arid climate. One shower may often be insufficient to trigger fingering in arid regions with short, heavy showers. In soils with shallow groundwater, the diverging subsoil flow determines solute leaching.  相似文献   

17.
The forest floor plays an important role in runoff rate, soil erosion and soil infiltration capacity by protecting mineral soils from the direct impact of falling raindrops. Forest floor consists of different kinds of litter with different hydraulic properties. In this study, the inverse method was used to estimate the hydraulic properties of three kinds of forest floor (broad‐leaved, needle‐leaved and mixed‐stand) at three replications in a completely random design. Forest floor samples were collected from the Gilan Province, Iran. The samples were piled up to make long columns 40.88 cm high with an inner diameter of 18.1 cm. Artificial rainfall experiments were conducted on top of the columns, and free drainage from the bottom of the columns was measured in the laboratory. Saturated hydraulic conductivity (Ks), saturated water content and water retention curve parameters (van Genuchten equation) were estimated by the inverse method. The results showed that the Ks of needle‐leaved samples differed significantly (p < 0.05) from those of broad‐leaved and mixed‐stand samples, whereas the latter two did not differ in this regard. No significant differences emerged in the water retention function parameters of van Genuchten (θr, β and α) in the three forest floor samples. The saturated water content of mixed‐stand samples was significantly different (p < 0.05) from that of broad‐leaved and needle‐leaved treatments with the latter two samples showing no significant difference. The good agreement between simulated and observed free drainage for all forest floor samples in the validation period indicates that the estimated hydraulic properties efficiently characterize the unsaturated water flow in the forest floor. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

18.
Post‐wildfire runoff was investigated by combining field measurements and modelling of infiltration into fire‐affected soils to predict time‐to‐start of runoff and peak runoff rate at the plot scale (1 m2). Time series of soil‐water content, rainfall and runoff were measured on a hillslope burned by the 2010 Fourmile Canyon Fire west of Boulder, Colorado during cyclonic and convective rainstorms in the spring and summer of 2011. Some of the field measurements and measured soil physical properties were used to calibrate a one‐dimensional post‐wildfire numerical model, which was then used as a ‘virtual instrument’ to provide estimates of the saturated hydraulic conductivity and high‐resolution (1 mm) estimates of the soil‐water profile and water fluxes within the unsaturated zone. Field and model estimates of the wetting‐front depth indicated that post‐wildfire infiltration was on average confined to shallow depths less than 30 mm. Model estimates of the effective saturated hydraulic conductivity, Ks, near the soil surface ranged from 0.1 to 5.2 mm h?1. Because of the relatively small values of Ks, the time‐to‐start of runoff (measured from the start of rainfall), tp, was found to depend only on the initial soil‐water saturation deficit (predicted by the model) and a measured characteristic of the rainfall profile (referred to as the average rainfall acceleration, equal to the initial rate of change in rainfall intensity). An analytical model was developed from the combined results and explained 92–97% of the variance of tp, and the numerical infiltration model explained 74–91% of the variance of the peak runoff rates. These results are from one burned site, but they strongly suggest that tp in fire‐affected soils (which often have low values of Ks) is probably controlled more by the storm profile and the initial soil‐water saturation deficit than by soil hydraulic properties. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.  相似文献   

19.
Predictions of post-wildfire flooding and debris flows are needed, typically with short lead times. Measurements of soil-hydraulic properties necessary for model parameterization are, however, seldom available. This study quantified soil-hydraulic properties, soil-water retention, and selected soil physical properties within the perimeter of the 2017 Thomas Fire in California. The Thomas Fire burn scar produced catastrophic debris flows in January 2018, highlighting the need for improved prediction capability. Soil-hydraulic properties were also indirectly estimated using relations tied to soil-water retention. These measurements and estimates are examined in the context of parameterizing post-wildfire hydrologic models. Tension infiltrometer measurements showed significant decreases (p < .05) in field-saturated hydraulic conductivity (Kfs) and sorptivity (S) in burned areas relative to unburned areas. Wildfire effects on soil water-retention were dominated by significant decreases in saturated soil-water content (θS). The van Genuchten parameters α, N, and residual water content did not show significant wildfire effects. The impacts of the wildfire on hydraulic and physical soil properties were greatest in the top 1 cm, emphasizing that measurements of post-fire soil properties should focus on the near-surface. Reductions in Kfs, θs, and soil-water retention in burned soils were attributed to fire-induced decreases in soil structure evidenced by increases in dry bulk density. Sorptivity reductions in burned soils were attributed to increases in soil-water repellency. Rapid post-fire assessments of flash flood and debris flow hazards using physically-based hydrologic models are facilitated by similarities between Kfs, S, and the Green–Ampt wetting front potential (ψf) with measurements at other southern CA burned sites. We suggest that ratios of burned to unburned Kfs (0.37), S (0.36), and ψf (0.66) could be used to scale unburned values for model parameterization. Alternatively, typical burned values (Kfs = 20 mm hr−1; S = 6 mm hr−0.5; ψf = 1.6 mm) could be used for model parameterization.  相似文献   

20.
Determination of saturated hydraulic conductivity, Ks, and the van Genuchten water retention curve θ(h) parameters is crucial in evaluating unsaturated soil water flow. The aim of this work is to present a method to estimate Ks, α and n from numerical analysis of an upward infiltration process at saturation (Cap0), with (Cap0 + h) and without (Cap0) an overpressure step (h) at the end of the wetting phase, followed by an evaporation process (Evap). The HYDRUS model as well as a brute-force search method were used for theoretical loam soil parameter estimation. The uniqueness and the accuracy of solutions from the response surfaces, Ks–n, α–n and Ks–α, were evaluated for different scenarios. Numerical experiments showed that only the Cap0 + Evap and Cap0 + h + Evap scenarios were univocally able to estimate the hydraulic properties. The method gave reliable results in sand, loam and clay-loam soils.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号