首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 281 毫秒
1.
Large deformations that accompany longwall mining result in complex spatial and temporal distributions of changes in undrained pore fluid pressures around the advancing face. These seemingly anomalous changes are recorded in the rapid water level response of undermined and adjacent wells, and may be explained in the short-term as a undrained poroelastic effect. A three-dimensional finite element model is applied to define anticipated pore fluid response both around the advancing mining face, at depth, and in the near surface region. The results are carefully verified against the response recorded at three well-instrumented longwall sites. Pore pressure changes are indexed directly to volumetric strains defining zones of significant depressurization in the caving zone and in zones of extension adjacent to the subsidence trough on the ground surface. Overpressurization occurs in the abutment region, at panel depth, and in the surface compressive zone immediately inside the angle-of-draw. These results are confirmed with available, short-term water level response data, defining the strongly heterogeneous spatial response and the significance of well depth on anticipated water level response.  相似文献   

2.
Paul Tammetta 《Ground water》2015,53(1):122-129
The change in hydraulic conductivity (K) above subsided longwall panels at underground coal mines is determined using a data base of pre‐mining and post‐mining K measurements made at multiple locations down the depth profile at each of a number of sites worldwide. Results show that, following caving of roof strata, there is a clear difference in the magnitude of changes in K above and below the top of the collapsed zone. Within the collapsed zone, relative increases in K are larger, even when taking account of measurements made in potentially unsaturated strata. A generalized conceptual model is presented for K change above subsided longwall panels. These results form a third independent database supporting the height of desaturation reported in an earlier study.  相似文献   

3.
The estimation of recharge through groundwater model calibration is hampered by the nonuniqueness of recharge and aquifer parameter values. It has been shown recently that the estimability of spatially distributed recharge through calibration of steady‐state models for practical situations (i.e., real‐world, field‐scale aquifer settings) is limited by the need for excessive amounts of hydraulic‐parameter and groundwater‐level data. However, the extent to which temporal recharge variability can be informed through transient model calibration, which involves larger water‐level datasets, but requires the additional consideration of storage parameters, is presently unknown for practical situations. In this study, time‐varying recharge estimates, inferred through calibration of a field‐scale highly parameterized groundwater model, are systematically investigated subject to changes in (1) the degree to which hydraulic parameters including hydraulic conductivity (K) and specific yield (Sy) are constrained, (2) the number of water‐level calibration targets, and (3) the temporal resolution (up to monthly time steps) at which recharge is estimated. The analysis involves the use of a synthetic reality (a reference model) based on a groundwater model of Uley South Basin, South Australia. Identifiability statistics are used to evaluate the ability of recharge and hydraulic parameters to be estimated uniquely. Results show that reasonable estimates of monthly recharge (<30% recharge root‐mean‐squared error) require a considerable amount of transient water‐level data, and that the spatial distribution of K is known. Joint estimation of recharge, Sy and K, however, precludes reasonable inference of recharge and hydraulic parameter values. We conclude that the estimation of temporal recharge variability through calibration may be impractical for real‐world settings.  相似文献   

4.
Abstract

The theoretical spatial distribution of hydraulic head during infiltration is used to interpret the results of infiltration experiments made in the field on a single, isolated, column of herbaceous peat in a flood-plain wetland in central England. Crusts of different hydraulic resistance were applied to the column surface. These regulated the water influx enabling the hydraulic conductivity of the peat to be estimated at between 1 and 19.5 m day-1. It is inferred that, when the hydraulic gradient changes, water may follow different pathways through the peat. Water moves rapidly through macropores in proportion to the applied hydraulic gradient, and infiltrates the peat matrix from the macropore walls. The results indicate the significance of hydraulic conductivity variations with depth, and the importance of precipitation intensity.  相似文献   

5.
Hard coal mining in the area of the Bytom Syncline (Upper Silesia Coal Basin, Poland) has been associated with the occurrence of high-energy seismic events (up to 109 J; local magnitude up to 4.0), which have been recorded by the local mining seismological network and regional seismological network. It has been noticed that the strongest seismic events occur when the mine longwall alignments coincide with the syncline axis. Data recorded by the improved local seismic network in the Bobrek Mine allow the estimation of the depths of the events’ hypocentres during excavation of longwall panel 3 as it approached the syncline axis. The recorded data were also used to estimate the location of the rupture surface and stress distribution in the seismic focus region. It was concluded that tectonic stresses, particularly horizontal stress components, are essential in the distribution of seismic tremors resulting from reverse faulting. The stresses induced by mining activity are only triggering tectonic deformations. The hypocentres of the strongest seismic events during mining of longwall panel 3/503 were located 300–800 m deeper than the level of coal seam 503.  相似文献   

6.
The role of lithology in influencing basin form and function is explored empirically by investigating correlations between a range of catchment variables, where the spatial unit of analysis is not surface catchments but lithologically coherent groundwater units. Using the Thames basin, UK, as a case study, nine groundwater units have been identified. Values for 11 hydrological and geomorphological variables, including rainfall, drainage density, Baseflow Index, aquifer porosity, storage coefficient and log‐hydraulic conductivity, aquifer and drainage elevation, river incision, and hypsometric integral have been estimated for each of the groundwater units in the basin, and Pearson correlation coefficients calculated for all pairs of variables. Seven of the correlation coefficients are found to be significant at a confidence level of > 99%. Negative correlations between drainage density and log aquifer hydraulic conductivity, and between drainage density and river incision, and positive correlations between log‐hydraulic conductivity and river incision, log‐hydraulic conductivity and Baseflow Index, and between Baseflow Index and river incision are inferred to have consistent causal explanations. For example, incision of rivers into aquifers leads to relative increases in hydraulic gradients in the vicinity of rivers which, in turn, promotes the development of secondary porosity increasing both aquifer hydraulic conductivity and, hence, Baseflow Index. The implication of this interpretation is that the geomorphological evolution of basins is intimately linked to the evolution of hydraulic conductivity of the underlying aquifers. This is consistent with, and supports the notion of a coupled complexly evolving surface water‐groundwater system. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

7.
In a previous study, a denitrification wall was constructed in a sand aquifer using sawdust as the carbon substrate. Ground water bypassed around this sawdust wall due to reduced hydraulic conductivity. We investigated potential reasons for this by testing two new walls and conducting laboratory studies. The first wall was constructed by mixing aquifer material in situ without substrate addition to investigate the effects of the construction technique (mixed wall). A second, biochip wall, was constructed using coarse wood chips to determine the effect of size of the particles in the amendment on hydraulic conductivity. The aquifer hydraulic conductivity was 35.4 m/d, while in the mixed wall it was 2.8 m/d and in the biochip wall 3.4 m/d. This indicated that the mixing of the aquifer sands below the water table allowed the particles to re-sort themselves into a matrix with a significantly lower hydraulic conductivity than the process that originally formed the aquifer. The addition of a coarser substrate in the biochip wall significantly increased total porosity and decreased bulk density, but hydraulic conductivity remained low compared to the aquifer. Laboratory cores of aquifer sand mixed under dry and wet conditions mimicked the reduction in hydraulic conductivity observed in the field within the mixed wall. The addition of sawdust to the laboratory cores resulted in a significantly higher hydraulic conductivity when mixed dry compared to cores mixed wet. This reduction in the hydraulic conductivity of the sand/sawdust cores mixed under saturated conditions repeated what occurred in the field in the original sawdust wall. This indicated that laboratory investigations can be a useful tool to highlight potential reductions in field hydraulic conductivities that may occur when differing materials are mixed under field conditions.  相似文献   

8.
  相似文献   

9.
The Surface Water and Ocean Topography (SWOT) satellite mission will provide global, space‐based estimates of water elevation, its temporal change, and its spatial slope in fluvial environments, as well as across lakes, reservoirs, wetlands, and floodplains. This paper illustrates the utility of existing remote sensing measurements of water temporal changes and spatial slope to characterize two complex fluvial environments. First, repeat‐pass interferometric SAR measurements from the Japanese Earth Resources Satellite are used to compare and contrast floodplain processes in the Amazon and Congo River basins. Measurements of temporal water level changes over the two areas reveal clearly different hydraulic processes at work. The Amazon is highly interconnected by floodplain channels, resulting in complex flow patterns. In contrast, the Congo does not show similar floodplain channels and the flow patterns are not well defined and have diffuse boundaries. During inundation, the Amazon floodplain often shows sharp hydraulic changes across floodplain channels. The Congo, however, does not show similar sharp changes during either infilling or evacuation. Second, Shuttle Radar Topography Mission measurements of water elevation are used to derive water slope over the braided Brahmaputra river system. In combination with in situ bathymetry measurements, water elevation and slope allow one to calculate discharge estimates within 2.3% accuracy. These two studies illustrate the utility of satellite‐based measurements of water elevation for characterizing complex fluvial environments, and highlight the potential of SWOT measurements for fluvial hydrology. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

10.
A. Altunkaynak  Z. Şen 《水文研究》2011,25(11):1778-1783
Darcian flow law in aquifers assumes that the aquifer hydraulic conductivity is constant and the groundwater movement is due only to the piezometric level changes through hydraulic gradient. In practice, after the well development the aquifer just around the well has comparatively larger hydraulic conductivity and gradient. Patchy aquifer solutions in the literature consider sudden hydraulic conductivity changes with distance for the steady state flow. The change of transmissivity is demonstrated by the application of slope‐matching procedure to actual field data. It is the main purpose of this paper to derive simple analytical expressions for aquifer parameter evaluations with steadily decreasing hydraulic conductivity around the well. Spatial nonlinear hydraulic conductivity changes around a large‐diameter well within the depression cone of a confined aquifer are considered as exponentially decreasing functions of the radial distance. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

11.
Abstract

Piezometers and wells installed for water quality monitoring are frequently used to assess the saturated hydraulic conductivity (K) in the surrounding formation. A series of recovery tests was conducted to evaluate how purging, required to obtain representative water quality samples, affected measured values of hydraulic conductivity in 15 newly installed and undeveloped piezometers placed to between 2 and 15 m depth (in oxidized and unoxidized material) in a loamy glacial till (K range from 10?6 to 10?9 m s?1). Piezometers were purged between 9 and 11 times for sampling over a period of five months. The effect of the purgings on piezometer development was evaluated by changes in slope of the water level recovery curves which were used to calculate hydraulic conductivity. The first five purgings following piezometer installation increased K in the 15 piezometers by an average of 34%. The average increase in a value of K after 10 purgings was 44%. Values measured for hydraulic conductivity in a 75 mm diameter auger hole appeared stable after four purgings but piezometers installed in larger diameter boreholes (100 mm to 280 mm) snowed increases in K with up to 10 purgings. The hydraulic conductivity determined for piezometers installed at a 30° angle to the vertical showed greater variability than was observed in the adjacent vertically installed piezometers at the same depth.  相似文献   

12.
Paul Tammetta 《Ground water》2016,54(5):646-655
Accurate estimation of the change in groundwater storage capacity (S) above mined longwall panels is vital for analysis of postmining void water level recovery in coal mines, and assessment of water quality impacts. At present, there is no generalized representation of the spatial distribution of changes in S around a panel. Current estimates are generally bulk averages with high uncertainty, precluding calculation of groundwater velocities in various parts of the subsurface. In this work, a recently published hydrogeological conceptual model of longwall caving is used in conjunction with observations from borehole extensometers, goaf height measurements, and pumping/drawdown records for mine pools to develop a subsurface spatial distribution of changes in S following longwall caving, with reduced uncertainty in their magnitudes. The assumption of saturation in the disturbed zone proved critical for obtaining accurate results and in reconciling widely varying published estimates of S. Results indicate that the goaf and collapsed zones each absorb over 30% of the mined volume, and about 20% is absorbed by the surface subsidence trough. The increase in S in the collapsed zone is inversely proportional to the amount of surface subsidence. The conceptual model is updated with these results to present the spatial distribution of S after caving. The results allow calculation of water velocities in various zones, and may provide greater accuracy in estimation of water level rebound and water quality processes. Most of the S participating in groundwater flows is provided by defects rather than the matrix.  相似文献   

13.
Infiltration is the primary mechanism in green stormwater infrastructure (GSI) systems to reduce the runoff volume from urbanized areas. Soil hydraulic conductivity is most important in influencing GSI infiltration rates. Saturated hydraulic conductivity (Ksat) is a critical parameter for GSI design and post-construction performance. However, Ksat measurement in the field is problematic due to temporal and spatial variability and measurement errors. This review paper focuses on a comparison of methods for in-situ Ksat measurement and the causes of temporal and spatial variations of Ksat within GSI systems. Automated infiltration testing methods, such as the Modified Philip–Dunne (MPD) and SATURO infiltrometers, show promise for efficient Ksat measurements. Soil Ksat values can change over time and substantially vary throughout a GSI, which can be attributed to multiple factors, including but not limited to temperature changes, soil composition and properties, soil compaction level, plant root morphology and distribution, biological and macrofauna activities in the soil, inflow sediment characteristics, quality of infiltrating water, and measurement errors. There is evidence that infiltration rates in vegetated urban GSI systems are sustained given an appropriate GSI design, reasonable concentration of suspended sediments in the inflow runoff, and routine maintenance procedures. These observations indicate that clogging can be counteracted by processes that tend to increase the soil hydraulic conductivity (e.g., plant root and biological activities). This self-sustainability underlines that infiltration-based GSI systems are a reliable long-term stormwater management solution. Recommendations on how to incorporate the temporal changes of Ksat in GSI design and on obtaining a spatially-representative Ksat for the GSI design are presented.  相似文献   

14.
Measurement uncertainty is a key hindrance to the quantification of water fluxes at all scales of investigation. Predictions of soil‐water flux rely on accurate or representative measurements of hydraulic gradients and field‐state hydraulic conductivity. We quantified the potential magnitude of errors associated with the parameters and variables used directly and indirectly within the Darcy – Buckingham soil‐water‐flux equation. These potential errors were applied to a field hydrometric data set collected from a forested hillslope in central Singapore, and their effect on flow pathway predictions was assessed. Potential errors in the hydraulic gradient calculations were small, approximately one order of magnitude less than the absolute magnitude of the hydraulic gradients. However, errors associated with field‐state hydraulic conductivity derivation were very large. Borehole (Guelph permeameter) and core‐based (Talsma ring permeameter) techniques were used to measure field‐saturated hydraulic conductivity. Measurements using these two approaches differed by up to 3\9 orders of magnitude, with the difference becoming increasingly marked within the B horizon. The sensitivity of the shape of the predicted unsaturated hydraulic conductivity curve to ±5% moisture content error on the moisture release curve was also assessed. Applied moisture release curve error resulted in hydraulic conductivity predictions of less than ±0\2 orders of magnitude deviation from the apparent conductivity. The flow pathways derived from the borehole saturated hydraulic conductivity approach suggested a dominant near‐surface flow pathway, whereas pathways calculated from the core‐based measurements indicated vertical percolation to depth. Direct tracer evidence supported the latter flow pathway, although tracer velocities were approximately two orders of magnitude smaller than the Darcy predictions. We conclude that saturated hydraulic conductivity is the critical hillslope hydrological parameter, and there is an urgent need to address the issues regarding its measurement further. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

15.
The spatial and temporal variability of groundwater–surface‐water (GW–SW) interactions was investigated in an intensively utilized salmon spawning riffle. Hydrochemical tracers, were used along with high‐resolution hydraulic head and temperature data to assess hyporheic dynamics. Surface and subsurface hydrochemistry were monitored at three locations where salmon spawning had been observed in previous years. Temperature and hydraulic head were monitored in three nests of three piezometers located to characterize the head, the run and the tail‐out of the riffle feature. Hydrochemical gradients between surface and subsurface water indicated increasing GW influence with depth into the hyporheic zone. Surface water was characterized by high dissolved oxygen (DO) concentrations, low alkalinity and conductivity. Hyporheic water was generally characterized by high levels of alkalinity and conductivity indicative of longer residence times, and low DO, indicative of reducing conditions. Hydrochemical and temperature gradients varied spatially over the riffle in response to changes in local GW–SW interactions at the depths investigated. Groundwater inputs dominated the head and tail of the riffle. The influence of SW increased in the area of accelerating flow and decreasing water depth through the run of the riffle. Temporal GW–SW interactions also varied in response to changing hydrological conditions. Gross changes in hyporheic hydrochemistry were observed at the weekly scale in response to changing flow conditions and surface water inputs to the hyporheic zone. During low flows, caused by freezing or dry weather, hyporheic hydrochemistry was dominated by GW inputs. During higher flows hyporheic hydrochemistry indicated that SW contributions increased. In addition, high‐resolution hydraulic head data indicated that rapid changes in GW–SW interactions occurred during hydrological events. The spatial, and possibly the temporal, variability of GW–SW interactions had a marked effect on the survival of salmon ova. It is concluded that hyporheic dynamics and their effect on stream ecology should be given increased consideration by fisheries and water resource managers. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

16.
In Belgium, IWVA uses managed aquifer recharge (MAR) to recharge the aquifer with treated wastewater generated from the communities to sustain the potable water supply on the Belgian coast. This MAR facility is faced with a challenge of reduced infiltration rates during the winter season when pond water temperatures near 4°C. This study involves the identification of the predominant factor influencing the rate of infiltration through the pond bed. Several factors, including pumping rates, natural recharge, tidal influences of the North Sea and pond-water temperature, were identified as potential causes for variation of the recharge rate. Correlation statistics and linear regression analysis were used to determine the sensitivity of the infiltration rate to the aforementioned factors. Two groundwater flow models were developed in visual MODFLOW to simulate the water movement under the pond bed and to obtain the differences in flux to track the effects of variation of hydraulic conductivity during the two seasons. A 32% reduction in vertical hydraulic gradient in the top portion of the aquifer was observed in winter, causing the recharge rates to fluctuate. Results showed that water temperature caused a 30% increase in hydraulic conductivity in summer as compared with winter and has the maximum impact on infiltration rate. Cyclic variations in water viscosity, occurring because of seasonal temperature changes, influence the saturated hydraulic conductivity of the pond bed. Results from the models confirm the impact on infiltration rate by temperature-influenced hydraulic conductivity.  相似文献   

17.
Paul Tammetta 《Ground water》2013,51(5):723-734
The height of complete groundwater drainage above subsided longwall panels (referred to as H) at underground mines is determined using a data base of hydraulic head measurements made with multiple devices down the depth profile at each of a number of sites worldwide. H is shown to be relatively independent of most parameters except the geometry of the mined void and the overburden thickness. An empirical equation linking H to these parameters is developed using hydraulic head data, and confirmed using an independent data base of ground movement. H is shown to be the same as the height of the zone of major ground movement above a panel. H for special cases (above longwall chain pillars, above pillar extraction panels, and underneath significant water bodies) is invariably smaller than H above center panel for ordinary cases. A new caving model, from a groundwater perspective, is proposed for continuously sheared longwall panels at ordinary locations. It removes complexity and reduces the uncertainty in estimating H. The derived equation for H applies to a variety of strata types.  相似文献   

18.
A pore‐scale model based on measured particle size distributions has been used to quantify the changes in pore space geometry of packed soil columns resulting from a dilution in electrolyte concentration from 500 to 1 mmol l?1 NaCl during leaching. This was applied to examine the effects of particle release and re‐deposition on pore structure and hydraulic properties. Two different soils, an agricultural soil and a mining residue, were investigated with respect to the change in hydraulic properties. The mining residue was much more affected by this process with the water saturated hydraulic conductivity decreasing to 0·4% of the initial value and the air‐entry value changing from 20 to 50 cm. For agricultural soil, there was little detectable shift in the water retention curve but the saturated hydraulic conductivity decreased to 8·5% of the initial value. This was attributed to localized pore clogging (similar to a surface seal) affecting hydraulic conductivity, but not the microscopically measured pore‐size distribution or water retention. We modelled the soil structure at the pore scale to explain the different responses of the two soils to the experimental conditions. The size of the pores was determined as a function of deposited clay particles. The modal pore size of the agricultural soil as indicated by the constant water retention curve was 45 µm and was not affected by the leaching process. In the case of the mining residue, the mode changed from 75 to 45 µm. This reduction of pore size corresponds to an increase of capillary forces that is related to the measured shift of the water retention curve. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

19.
This paper presents an in situ falling-head method for measuring hydraulic conductivity of beach sediments in tidal environment. A polyvinyl chloride (PVC) standpipe was vertically pushed into the submerged beach sediments so that its lower part was filled by a sediment column. During the experiment, the sediments were submerged by sea water and the standpipe top was higher than the sea level. The pipe was fully filled with sea water at the beginning of the experiment. Then the water level time series inside and outside the standpipe were recorded. Analytical solutions were derived to describe the relation among the sediment's hydraulic conductivity and the water levels inside and outside the standpipe and used to analyze the experiment data obtained from the intertidal zone of Puqian Bay, Haikou, Hainan Province, China. The water levels predicted by the analytical solution agreed very well with all the experiment data. Experiments for horizontal hydraulic conductivity estimation were also conducted using L-shaped standpipe which bends from vertical to horizontal in the beach sediments. The averaged hydraulic conductivity anisotropy ratio at the study area is about 2.9. After each in situ experiment, the sediments in the standpipe were stored in a plastic box and transported to university laboratory to measure the hydraulic conductivity using falling-head method. It is found that the in situ hydraulic conductivity averages one order of magnitude greater than the laboratory one, indicating that the original beach surface sediments were loose due to tidal and wave actions and that the samples were significantly compacted during the transportation to laboratory.  相似文献   

20.
The ionic strength of percolating water can greatly alter a soil's hydraulic conductivity. This appears to be the result of dispersion and/or swelling of clay particles, and can alter hydraulic conductivity by several orders of magnitude.

In this paper, the potential effects of salinity-dependent changes in hydraulic conductivity during saltwater intrusions are analyzed. Results are presented to show that this can increase the degree to which brackish water will penetrate a coastal aquifer. This can also increase the width of the dispersed salt front, and can lead to a much greater circulation of saltwater within the intruding saltwater toe. These results may help to explain field observations that have previously been attributed to “scale-dependent” dispersivity and domain heterogeneity.  相似文献   


设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号