首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 531 毫秒
1.
剪切波速与地基土的抗剪强度、剪切模量和卓越周期等参数密切相关,是地震安全性评价中判定场地类别的一个主要指标和参数。鉴于海域工程中剪切波速往往难以直接由原位测得,而室内实验结果又常常与野外现场物探测试值存在较大差异,因此,如何通过其他途径有效获取满足工程需要的剪切波速参数在海域工程的地震安全性评价等方面具有迫切的实用需求。为此本文通过对渤海海域数十个石油平台项目中一系列饱和黏性土样品的剪切波速与抗剪强度实验数据的统计分析,尝试采用多种可能的函数来拟合确定二者之间的经验关系。结果表明:对于渤海海域黏性土剪切波速V_s与抗剪强度S_u之间的最佳统计经验关系为幂函数V_s=53.751S_u~(0.376)。此关系可为渤海海域工程中通过不排水抗剪强度估算剪切波速提供一种简便可行的实用性方法。  相似文献   

2.
土体剪切波速是进行土层地震反应分析的动力学参数，对场地地震动参数确定具有重要意义。基于地质地貌分析，将大同盆地划分为5类典型地质单元。对盆地1429个钻孔剪切波速资料进行分析，探讨VS30与VS20的相关性，研究土体埋深、岩性、地质单元、标贯击数及密实度等地质特征对VS的影响，并基于地质单元、剪切波速比、密实度系数及第四系上部覆盖层厚度相关性分析给出土体VS30预测模型。研究结果表明，基于典型地质特征的VS30预测模型拟合优度R2>0.90，预测精度很高，对于离散性较大、直接拟合估算较差及无剪切波速场地来说，以区分地质单元及土体类型的方式进行VS30分解预测是良好的研究思路。首次在区分地质单元及土体类型的前提下提出剪切波速比及密实度系数，并将其与第四系上部覆盖层厚度综合应用于VS30预测研究。研究结果可为大同盆地城市防震减灾规划、震害预测、区域性地震安全评价提供重要技术支撑。  相似文献   

3.
Deep unconsolidated sediments in the Mississippi embayment will influence ground motions from earthquakes in the New Madrid seismic zone. Shear wave velocity profiles of these sediments are important input parameters for modeling wave propagation and site response in this region. Low-frequency, active-source surface wave velocity measurements were performed to develop small-strain shear wave velocity (VS) profiles at eleven deep soil sites in the Mississippi embayment, from north of New Madrid, Missouri to Memphis, Tennessee. A servo-hydraulic, low-frequency source was used to excite surface wave energy to wavelengths of 600 m, resulting in VS profiles to depths of over 200 m. The average VS profile calculated from the eleven sites is in good agreement with common reference VS profiles that have been used in seismic hazard studies of this region. The variability in VS profiles is shown to be associated with changes in formation depth and thickness from site-to-site. Using lithologic information at each site, average formation velocities were developed and compared to previous studies. We found average VS values of about 193 m/s for alluvial deposits, 400 m/s for the Upper Claiborne formations, and 685 m/s for the Memphis Sand formation.  相似文献   

4.
A practical method is presented for determining three‐dimensional S‐wave velocity (VS) profile from microtremor measurements. Frequency–wave number (f–k) spectral analyses of microtremor array records are combined, for this purpose, with microtremor horizontal‐to‐vertical (H/V) spectral ratio techniques. To demonstrate the effectiveness of the proposed method, microtremor measurements using arrays of sensors were conducted at six sites in the city of Kushiro, Japan. The spectral analyses of the array records yield dispersion characteristics of Rayleigh waves and H/V spectra of surface waves, and joint inversion of these data results in VS profiles down to bedrock at the sites. Conventional microtremor measurements were performed at 230 stations within Kushiro city, resulting in the H/V spectra within the city. Three‐dimensional VS structure is then estimated from inversion of the H/V spectra with the VS values determined from the microtremor array data. This reveals three‐dimensional VS profile of Kushiro city, together with an unknown hidden valley that crosses the central part of the city. The estimated VS profile is consistent with available velocity logs and results of subsequent borings, indicating the effectiveness of the proposed method. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

5.
High-frequency (≥2 Hz) Rayleigh wave phase velocities can be inverted to shear (S)-wave velocities for a layered earth model up to 30 m below the ground surface in many settings. Given S-wave velocity (VS), compressional (P)-wave velocity (VP), and Rayleigh wave phase velocities, it is feasible to solve for P-wave quality factor QP and S-wave quality factor QS in a layered earth model by inverting Rayleigh wave attenuation coefficients. Model results demonstrate the plausibility of inverting QS from Rayleigh wave attenuation coefficients. Contributions to the Rayleigh wave attenuation coefficients from QP cannot be ignored when Vs/VP reaches 0.45, which is not uncommon in near-surface settings. It is possible to invert QP from Rayleigh wave attenuation coefficients in some geological setting, a concept that differs from the common perception that Rayleigh wave attenuation coefficients are always far less sensitive to QP than to QS. Sixty-channel surface wave data were acquired in an Arizona desert. For a 10-layer model with a thickness of over 20 m, the data were first inverted to obtain S-wave velocities by the multichannel analysis of surface waves (MASW) method and then quality factors were determined by inverting attenuation coefficients.  相似文献   

6.
目前,主要依靠室内动力试验对黄土液化势进行评价。由于黄土特殊的结构性,室内试验对其饱和的过程较为复杂,且与实际场地饱和黄土差异明显,导致室内黄土液化试验结果并不能代表现场饱和黄土的抗液化强度。本文选取兰州市西固区寺儿沟村某饱和黄土场地进行钻孔测试,现场实施了标准贯入试验、静力触探试验以及剪切波速测试。应用Robertson的土类指数分类图对该场地不同含水率黄土的土类进行了界定,确定了饱和黄土属于类砂土,有液化势。应用NCEER推荐方法,计算了3组原位试验数据的饱和黄土循环抗力比（CRR）,通过与1976年唐山地震和1999年集集地震液化土CRR对比,得出了饱和黄土抗液化强度很低的结论。  相似文献   

7.
Three methods that follow the general format of the Seed-Idriss simplified procedure for evaluating liquefaction resistance of soils are compared in this paper. They are compared by constructing relationships between penetration resistance and small-strain shear–wave velocity (VS) implied from cyclic resistance ratio (CRR) curves for the three methods, and by plotting penetration-VS data pairs. The penetration-VS data pairs are from 43 Holocene-age sand layers in California, South Carolina, Canada, and Japan. It is shown that the VS-based CRR curve is more conservative than CRR curves based on the Standard Penetration Test (SPT) and Cone Penetration Test (CPT), for the compiled Holocene data. This result agrees with the findings of a recent probability study where the SPT-, CPT-, and VS-based CRR curves were characterized as curves with average probability of liquefaction of 31, 50, and 26%, respectively. New SPT- and CPT-based CRR equations are proposed that provide more consistent assessments of liquefaction potential for the Holocene sand layers considered.  相似文献   

8.
Forward modeling is of critical importance for inversion analysis of surface wave methods to obtain shear-wave velocity (VS) profiles of soil sites. The dynamic stiffness matrix (DSM) method can provide forward modeling of Rayleigh surface waves to simulate complex wave propagation in layered soil sites. However, contamination from body waves and interference of multiple Rayleigh wave modes can reduce the accuracy of theoretical dispersion curves, especially at irregular soil sites with embedded low-velocity or high-velocity layers. An analytical method is developed herein to combine the techniques of the multichannel analysis of surface waves method with the DSM method to improve the accuracy of the theoretical dispersion analysis for soil sites. The proposed method implements multichannel analysis of the analytical displacement responses to capture dominant dispersion trends. Comparison of the results obtained with the new method against those from the transfer matrix method and the literature indicates that the new method can (1) effectively minimize the effects of contamination caused by body waves and interference from several Rayleigh wave modes, and (2) generate accurate dominant dispersion trends for soil sites with various stiffness profiles, especially for the high-frequency dispersion characteristics of the profiles with embedded low-velocity layers.  相似文献   

9.
Recent field tests illustrate the accuracy and consistency of calculating near-surface shear (S)-wave velocities using multichannel analysis of surface waves (MASW). S-wave velocity profiles (S-wave velocity vs. depth) derived from MASW compared favorably to direct borehole measurements at sites in Kansas, British Columbia, and Wyoming. Effects of changing the total number of recording channels, sampling interval, source offset, and receiver spacing on the inverted S-wave velocity were studied at a test site in Lawrence, Kansas. On the average, the difference between MASW calculated Vs and borehole measured Vs in eight wells along the Fraser River in Vancouver, Canada was less than 15%. One of the eight wells was a blind test well with the calculated overall difference between MASW and borehole measurements less than 9%. No systematic differences were observed in derived Vs values from any of the eight test sites. Surface wave analysis performed on surface data from Wyoming provided S-wave velocities in near-surface materials. Velocity profiles from MASW were confirmed by measurements based on suspension log analysis.  相似文献   

10.
景亮  吴琪  方怡 《震灾防御技术》2020,15(4):696-707
为探讨测试方法、试验条件以及级配特征对砂-粉混合料剪切波速的影响，对具有不同细粒含量FC，相对密度Dr以及初始有效围压$\sigma_{3 \mathrm{c}}^{\prime}$的砂-粉混合料进行弯曲元和共振柱试验。结果表明:当Dr =35%或50%时，剪切波速Vs随FC的增大先减小后增大；当Dr =60%时，Vs随FC的增大而减小；弯曲元试验测得的Vs明显大于共振柱试验测得的Vs，随着FC的增大，弯曲元试验与共振试验得到的Vs差值逐渐减小，而当FC＞20%时，两种试验得到的Vs基本相同。在考虑Vs弥散性之后，不同FC的混合料弯曲元与共振柱试验得到的Vs结果具有较好的一致性。基于Hardin模型建立的砂-粉混合料Vs预测方法具有较好的预测效果。  相似文献   

11.
— Detailed shear-wave velocity profiles versus depth have been obtained in typical lithostratigraphies of Napoli. FTAN and hedgehog methods have been applied to Rayleigh surface waves recorded in refraction seismic surveys. The comparison with literature measurements shows good agreement with nearby down- and cross-hole tests. The pumiceous and lapilli content, and the different welding and alteration degree of the Neapolitan pyroclastic soils cause a strong scattering of the shear wave velocities (VS) from bore-hole measurements, even for the same formation. Surface measurements, based on FTAN-hedgehog methods, determine average VS along travel paths of about 100 m, give results that are comparable with down- and cross-hole velocity profiles, and have the additional advantage of being less scattered, and thus more representative of average properties than bore-hole measurements. The results of surface measurements should be preferred in the computation of realistic seismograms and are particularly suitable in urban areas, as they are not destructive and need just one receiver.  相似文献   

12.
Accurate determination of seismic velocity of the crust is important for understanding regional tectonics and crustal evolution of the Earth. We propose a stepwise joint linearized inversion method using surface wave dispersion, Rayleigh wave ZH ratio (i.e., ellipticity), and receiver function data to better resolve 1D crustal shear wave velocity (v S) structure. Surface wave dispersion and Rayleigh wave ZH ratio data are more sensitive to absolute variations of shear wave speed at depths, but their sensitivity kernels to shear wave speeds are different and complimentary. However, receiver function data are more sensitive to sharp velocity contrast (e.g., due to the existence of crustal interfaces) and v P/v S ratios. The stepwise inversion method takes advantages of the complementary sensitivities of each dataset to better constrain the v S model in the crust. We firstly invert surface wave dispersion and ZH ratio data to obtain a 1D smooth absolute v S model and then incorporate receiver function data in the joint inversion to obtain a finer v S model with better constraints on interface structures. Through synthetic tests, Monte Carlo error analyses, and application to real data, we demonstrate that the proposed joint inversion method can resolve robust crustal v S structures and with little initial model dependency.  相似文献   

13.
In this study, a set of charts are developed to estimate shear wave velocity of soils in the New Madrid seismic zone (NMSZ), using the standard penetration test (SPT) N values and soil depths. Laboratory dynamic test results of soil samples collected from the NMSZ showed that the shear wave velocity of soils is related to the void ratio and the effective confining pressure applied to the soils. The void ratio of soils can be estimated from the SPT N values and the effective confining pressure depends on the depth of soils. Therefore, the shear wave velocity of soils can be estimated from the SPT N value and the soil depth. To make the methodology practical, two corrections should be made. One is that field SPT N values of soils must be adjusted to an unified SPT N′ value to account the effects of overburden pressure and equipment. The second is that the effect of water table to effective overburden pressure of soils must be considered. To verify the methodology, shear wave velocities of five sites in the NMSZ are estimated and compared with those obtained from field measurements. The comparison shows that our approach and the field tests are consistent with an error of less than of 15%. Thus, the method developed in this study is useful for dynamic study and practical designs in the NMSZ region.  相似文献   

14.
Understanding the soil–structure interaction (SSI) mechanism is crucial in the seismic design of nuclear power plant (NPP) containment systems. Although the numerical analysis method is generally used in seismic design, there is a need for experimental verification for the reliable estimation of SSI behavior. In this study a dynamic centrifuge test was performed to simulate the SSI behavior of a Hualien large-scale seismic test (LSST) during the Chi-Chi earthquake. To simulate the soil profile and dynamic soil properties of the Hualien site, a series of resonant column (RC) tests was performed to determine the model soil preparation conditions, such as the compaction density and the ratio of soil–gravel contents. The variations in the shear wave velocity (VS) profiles of the sand, gravel, and backfill layers in the model were estimated using the RC test results. During the centrifuge test, the VS profiles of the model were evaluated using in-flight bender element tests and compared with the in-situ VS profile at Hualien. The containment building model was modeled using aluminum and the proper scaling laws. A series of dynamic centrifuge tests was performed with a 1/50 scale model using the base motion recorded during the Chi-Chi-earthquake. In the soil layer and foundation level, the centrifuge test results were similar to the LSST data in both the time and frequency domains, but there were differences in the structure owing to the complex structural response as well as the material damping difference between the concrete in the prototype and aluminum in the model. In addition, as the input base motion amplitude was increased to a maximum value of 0.4g (prototype scale), the responses of the soil and containment model were measured. This study shows the potential of utilizing dynamic centrifuge tests as an experimental modeling tool for site specific SSI analyses of soil–foundation–NPP containment system.  相似文献   

15.
Shear wave velocity (V S) can be obtained using seismic tests, and is viewed as a fundamental geotechnical characteristic for seismic design and seismic performance evaluation in the field of earthquake engineering. To apply conventional geotechnical site investigation techniques to geotechnical earthquake engineering, standard penetration tests (SPT) and piezocone penetration tests (CPTu) were undertaken together with a variety of borehole seismic tests for a range of sites in Korea. Statistical modeling of the in-situ testing data identified correlations between V S and geotechnical in-situ penetration data, such as blow counts (N value) from SPT and CPTu data including tip resistance (q t), sleeve friction (f s), and pore pressure ratio (B q). Despite the difference in strain levels between conventional geotechnical penetration tests and borehole seismic tests, it is shown that the suggested correlations in this study is applicable to the preliminary determination of V S for soil deposits.  相似文献   

16.
Elastic imaging from ocean bottom cable (OBC) data can be challenging because it requires the prior estimation of both compressional‐wave (P‐wave) and shear‐wave (S‐wave) velocity fields. Seismic interferometry is an attractive technique for processing OBC data because it performs model‐independent redatuming; retrieving ‘pseudo‐sources’ at positions of the receivers. The purpose of this study is to investigate multicomponent applications of interferometry for processing OBC data. This translates into using interferometry to retrieve pseudo‐source data on the sea‐bed not only for multiple suppression but for obtaining P‐, converted P to S‐wave (PS‐wave) and possibly pure mode S‐waves. We discuss scattering‐based, elastic interferometry with synthetic and field OBC datasets. Conventional and scattering‐based interferometry integrands computed from a synthetic are compared to show that the latter yields little anti‐causal response. A four‐component (4C) pseudo‐source response retrieves pure‐mode S‐reflections as well at P‐ and PS‐reflections. Pseudo‐source responses observed in OBC data are related to P‐wave conversions at the seabed rather than to true horizontal or vertical point forces. From a Gulf of Mexico OBC data set, diagonal components from a nine‐component pseudo‐source response demonstrate that the P‐wave to S‐wave velocity ratio (VP/VS) at the sea‐bed is an important factor in the conversion of P to S for obtaining the pure‐mode S‐wave reflections.  相似文献   

17.
We have studied 56 unfractured chalk samples of the Upper Cretaceous Tor Formation of the Dan, South Arne and Gorm Fields, Danish North Sea. The samples have porosities of between 14% and 45% and calcite content of over 95%. The ultrasonic compressional‐ and shear‐wave velocities (VP and VS) for dry and water‐saturated samples were measured at up to 75 bar confining hydrostatic pressure corresponding to effective stress in the reservoir. The porosity is the main control of the ultrasonic velocities and therefore of the elastic moduli. The elastic moduli are slightly higher for samples from the South Arne Field than from the Dan Field for identical porosities. This difference may be due to textural differences between the chalk at the two locations because we observe that large grains (i.e. filled microfossils and fossil fragments) that occur more frequently in samples from the Dan Field have a porosity‐reducing effect and that samples rich in large grains have a relatively low porosity for a given P‐wave modulus. The clay content in the samples is low and is mainly represented by either kaolinite or smectite; samples with smectite have a lower P‐wave modulus than samples with kaolinite at equal porosity. We find that ultrasonic VP and VS of dry chalk samples can be satisfactorily estimated with Gassmann's relationships from data for water‐saturated samples. A pronounced difference between the VP/VS ratios for dry and water‐saturated chalk samples indicates promising results for seismic amplitude‐versus‐offset analyses.  相似文献   

18.
We made an attempt to assess the shear wave velocity values V S and, to a lesser extent, the V P values from ambient noise recordings in an array configuration. Five array sites were situated in the close proximity to borehole sites. Shear wave velocity profiles were modeled at these five array sites with the aid of two computational techniques, viz. spatial autocorrelation (SPAC) and H/V ellipticity. Out of these five array sites, velocity estimates could be reliably inferred at three locations. The shear wave velocities estimated by these methods are found to be quite consistent with each other. The computed V S values up to 30 m depth are in the range from 275 to 375 m/s in most of the sites, which implies prevalence of a low velocity zone at some pocket areas. The results were corroborated by evidence of site geology as well as geotechnical information.  相似文献   

19.
The feasibility of using the optimum seeking method to assess the seismic liquefaction potential of sands has been investigated. Optimization theory is a very important branch of applied mathematics and has a wide application in the practical world. Using the available field sand liquefaction data, the influence of various factors is quantified using the optimum seeking method. The factors considered are: the earthquake magnitude M, the distance of the site from the source of the earthquake L, the depth of the water table Dw, the depth of the sand deposit Ds, and the standard penetration test (SPT) blow count N. The most important factors have been identified as the earthquake magnitude and the SPT blow count. Prediction results show that the proposed method is effective and feasible. Since neither normalization of the SPT blow count nor calculation of the seismic shear-stress ratio are required, the proposed method is simpler and more direct than the conventional methods of evaluating liquefaction potential.  相似文献   

20.
The application of the simplified method for evaluating the liquefaction potential based on shear wave velocity measurements has increased substantially due to its advantages, especially for microzonation of liquefaction potential. In the simplified method, a curve is proposed to correlate the cyclic resistance ratio (CRR) with overburden stress-corrected shear wave velocity (Vs1). However, the uniqueness of this curve for all types of soils is questionable. The objective of this research is to study whether the correlation between CRR and Vs1 is unique or not. Besides, the necessity of developing the soil-specific correlations is also investigated. Based on laboratory test data, a new semi-empirical method is proposed to establish the soil-specific CRR–Vs1 correlation. To validate the proposed method, a number of undrained cyclic triaxial tests along with bender element tests were performed on two types of sands. Similar experimental data for six other types of sands reported in the literature was also compiled. Applying the proposed method, soil-specific CRR–Vs1 correlation curves were developed for these eight types of sands. It is shown that the correlation is not unique for different types of sands and the boundary curve proposed in the available simplified method can only be used as an initial estimation of liquefaction resistance. Finally, using the results of this study as well as previous ones, a chart is suggested to be used in engineering practice showing the conditions for which a detailed soil-specific CRR–Vs1 correlation study needs to be performed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号