首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 859 毫秒
1.
Assessing liquefaction potential, in situ screening using cone penetration resistance, and liquefaction-remediation of non-plastic silty soils are difficult problems. Presence of silt particles among the sand grains in silty soils alter the moduli, shear strength, and flow characteristics of silty soils compared to clean host sand at the same global void ratio. Cyclic resistance (CRR) and normalized cone penetration resistance (qc1N) are each affected by silt content in a different way. Therefore, a unique correlation between cyclic resistance and cone resistance is not possible for sands and silty sands. Likewise, the response of silty soils subjected to traditional deep dynamic compaction (DC) and vibro-stone column (SC) densification techniques is influenced by the presence of silt particles, compared to the response in sand. Silty soils require drainage-modifications to make them amenable for dynamic densification techniques. The first part of this paper addresses the effects of silt content on cyclic resistance CRR, hydraulic conductivity k, and coefficient of consolidation Cv of silty soils compared to clean sand. The second part of the paper assesses the effectiveness of equivalent intergranular void ratio (ec)eq concept to approximately account for the effects of silt content on CRR. The third part of the paper explores the combined effects of silt content (viz effects of (ec)eq, k, and Cv) on qc1N using laboratory model cone tests and preliminary numerical simulation experiments. A possible inter-relationship between qc1N, CRR, accommodating the different degrees of influence of (ec)eq, k, and Cv on qc1N and CRR, is discussed. The fourth part of the paper focuses on the detrimental effects of silt content on the effectiveness of DC and SC techniques to densify silty soils for liquefaction-mitigation. Finally, the effectiveness of supplemental wick drains to aid drainage and facilitate densification and liquefaction mitigation of silty sands using DC and SC techniques is discussed.  相似文献   

2.
A series of undrained cyclic direct simple shear tests, which used a soil container with a membrane reinforced with stack rings to maintain the K0 condition and integrated bender elements for shear wave velocity measurement, were performed to study the liquefaction characteristics of gap-graded gravelly soils with no fines content. The intergrain state concept was employed to categorize gap-graded sand–gravel mixtures as sand-like, gravel-like, and in-transition soils, which show different liquefaction characteristics. The testing results reveal that a linear relationship exists between the shear wave velocity and the minor fraction content for sand–gravel mixtures at a given skeleton void ratio of the major fraction particles. For gap-graded gravelly sand, the gravel content has a small effect on the liquefaction resistance, and the cyclic resistance ratio (CRR) of gap-graded gravelly sands can be evaluated using current techniques for sands with gravel content corrections. In addition, the results indicate that the current shear wave velocity (Vs) based correlation underestimates the liquefaction resistance for Vs values less than 160 m/s, and different correlations should be proposed for sand-like and gravel-like gravelly soils. Preliminary modifications to the correlations used in current evaluations of liquefaction resistance have thus been proposed.  相似文献   

3.
This paper investigates the postcyclic behavior of low-plasticity silt with excess pore pressure ratio (Ru) less than 1. The testing specimens were prepared from Mississippi River Valley (MRV) silt. Full and no reconsolidation were allowed after specimens were subjected to various excess pore pressure ratios due to cyclic loading in a cyclic triaxial cell, and then monotonic shear tests were conducted. The effect of the Ru on shear strength and stiffness at small and large deformation was investigated. It was found that a Ru greater than 0.70 is a prerequisite of large increase in volumetric strain and undrained shear strength for specimens with full reconsolidation. In contrast, a significant decrease in yield shear strength and initial stiffness was noted for specimens without reconsolidation. In comparison to published data for sands, the silt experienced significant volumetric strain due to reconsolidation at lower Ru, indicating that the specimen fabric was modified or strained at lower Ru.  相似文献   

4.
The application of the simplified method for evaluating the liquefaction potential based on shear wave velocity measurements has increased substantially due to its advantages, especially for microzonation of liquefaction potential. In the simplified method, a curve is proposed to correlate the cyclic resistance ratio (CRR) with overburden stress-corrected shear wave velocity (Vs1). However, the uniqueness of this curve for all types of soils is questionable. The objective of this research is to study whether the correlation between CRR and Vs1 is unique or not. Besides, the necessity of developing the soil-specific correlations is also investigated. Based on laboratory test data, a new semi-empirical method is proposed to establish the soil-specific CRR–Vs1 correlation. To validate the proposed method, a number of undrained cyclic triaxial tests along with bender element tests were performed on two types of sands. Similar experimental data for six other types of sands reported in the literature was also compiled. Applying the proposed method, soil-specific CRR–Vs1 correlation curves were developed for these eight types of sands. It is shown that the correlation is not unique for different types of sands and the boundary curve proposed in the available simplified method can only be used as an initial estimation of liquefaction resistance. Finally, using the results of this study as well as previous ones, a chart is suggested to be used in engineering practice showing the conditions for which a detailed soil-specific CRR–Vs1 correlation study needs to be performed.  相似文献   

5.
Cyclic shear response of channel-fill Fraser River Delta silt   总被引：2，自引：0，他引：2  
The cyclic shear response of a channel-fill, low-plastic silt was investigated using constant-volume direct simple shear testing. Silt specimens, initially consolidated to stress levels at or above the preconsolidation stress, displayed cyclic-mobility-type strain development during cyclic loading without static shear stress bias. Liquefaction in the form of strain softening accompanied by loss of shear strength did not manifest regardless of the applied cyclic stress ratio, or the level of induced excess pore water pressure, suggesting that the silt is unlikely to experience flow failure under cyclic loading. The cyclic shear resistance of the silt increased with increasing overconsolidation ratio (OCR) for OCR>1.3. The silt specimens that experienced high equivalent excess cyclic pore water pressure ratios (ru>80%) resulted in considerable volumetric strains (2.5%–5%) during post-cyclic reconsolidation implying potentially significant changes to the particle fabric under cyclic loading.  相似文献   

6.
Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversial issues. This paper presents the results of an experimental evaluation to address these issues. Two parameters, namely, equivalent intergranular void ratio （ec）eq and equivalent interfine void ratio （ef）eq, proposed in a companion paper （Thevanayagam, 2007） as indices of active grain contacts in a granular mix, are used to characterize liquefaction resistance of sands and silty sands. Results indicate that, at the same global void ratio （e）, liquefaction resistance of silty sand decreases with an increase in fines content （Cv） up to a threshold value （Crth）. This is due to a reduction in intergrain contact density between the coarse grains. Beyond Crth, with further addition of fines, the interfine contacts become significant while the inter-coarse grain contacts diminish and coarse grains become dispersed. At the same e, the liquefaction resistance increases and the soil becomes stronger with a fttrther increase in silt content. Beyond a limiting fines content （CrL）, the liquefaction resistance is controlled by interfine contacts only. When Cr〈Crth, at the same （e）eq, the liquefaction resistance of silty sand is comparable to that of the host clean sand at a void ratio equal to （ec）eq. When CF〉CFth, at the same （ef）eq, the cyclic strength of a sandy silt is comparable to the host silt at a void ratio equal to （ef）eq.  相似文献   

7.
The evaluation and design of stone column improvement ground for liquefaction mitigation is a challenging issue for the state of practice. In this paper, a shear wave velocity-based approach is proposed based on the well-defined correlations of liquefaction resistance (CRR)-shear wave velocity (V s)-void ratio (e) of sandy soils, and the values of parameters in this approach are recommended for preliminary design purpose when site specific values are not available. The detailed procedures of pre- and post-improvement liquefaction evaluations and stone column design are given. According to this approach, the required level of ground improvement will be met once the target V s of soil is raised high enough (i.e., no less than the critical velocity) to resist the given earthquake loading according to the CRR-V s relationship, and then this requirement is transferred to the control of target void ratio (i.e., the critical e) according to the V s-e relationship. As this approach relies on the densification of the surrounding soil instead of the whole improved ground and is conservative by nature, specific considerations of the densification mechanism and effect are given, and the effects of drainage and reinforcement of stone columns are also discussed. A case study of a thermal power plant in Indonesia is introduced, where the effectiveness of stone column improved ground was evaluated by the proposed V s-based method and compared with the SPT-based evaluation. This improved ground performed well and experienced no liquefaction during subsequent strong earthquakes.  相似文献   

8.

In engineering practice, the liquefaction potential of a sandy soil is usually evaluated with a semi-empirical, stress-based approach computing a factor of safety in free field conditions, defined as the ratio between the liquefaction resistance (capacity) and the seismic demand. By so doing, an estimate of liquefaction potential is obtained, but nothing is known on the pore pressure increments (often expressed in the form of normalized pore pressure ratio ru) generated by the seismic action when the safety factor is higher than 1. Even though ru can be estimated using complex numerical analyses, it would be extremely useful to have a simplified procedure to estimate them consistent with the stress-based approach adopted to check the safety conditions. This paper proposes such a procedure with reference to both saturated and unsaturated soils, considering the latter as soils for which partial saturation has been artificially generated with some ground improvement technology to increase cyclic strength and thus tackle liquefaction risk. A simple relationship between the liquefaction free field safety factor FS, and ru(Sr) is introduced, that generalizes a previous expression proposed by Chiaradonna and Flora (Geotech Lett, 2020. https://doi.org/10.1680/jgele.19.00032) for saturated soils. The new procedure has been successfully verified against some experimental data, coming from laboratory constant amplitude cyclic tests and from centrifuge tests with irregular acceleration time histories for soils having different gradings and densities.

  相似文献   

9.
Three methods that follow the general format of the Seed-Idriss simplified procedure for evaluating liquefaction resistance of soils are compared in this paper. They are compared by constructing relationships between penetration resistance and small-strain shear–wave velocity (VS) implied from cyclic resistance ratio (CRR) curves for the three methods, and by plotting penetration-VS data pairs. The penetration-VS data pairs are from 43 Holocene-age sand layers in California, South Carolina, Canada, and Japan. It is shown that the VS-based CRR curve is more conservative than CRR curves based on the Standard Penetration Test (SPT) and Cone Penetration Test (CPT), for the compiled Holocene data. This result agrees with the findings of a recent probability study where the SPT-, CPT-, and VS-based CRR curves were characterized as curves with average probability of liquefaction of 31, 50, and 26%, respectively. New SPT- and CPT-based CRR equations are proposed that provide more consistent assessments of liquefaction potential for the Holocene sand layers considered.  相似文献   

10.
This paper describes a case-history of liquefaction occurred near the village of Vittorito after the April 6, 2009 L’Aquila earthquake (moment magnitude Mw = 6.3), approximately 45 km far from the epicentre. In the document, first, an estimation of the seismic motion in the area has been made. Thereafter, the performed geotechnical investigation is described, followed by the application of some fast assessment criteria for the occurrence of liquefaction, recently proposed by the new Italian Building Code. A careful assessment of all the parameters involved in conventional Seed and Idriss (1971) liquefaction analyses is considered. The cyclic resistance ratio CRR is evaluated by cone penetration tests CPT and by in situ seismic dilatometer tests SMDT; in the latter case CRR is evaluated by different empirical correlations with shear wave velocity Vs and horizontal stress index KD. Analytical data confirmed the observed occurrence of the liquefaction in Vittorito, even if the acceleration field in the area, produced by the L’Aquila earthquake, was very low.  相似文献   

11.
Intergrain contact density indices for granular mixes I： Framework   总被引：2，自引：0，他引：2  
Mechanical behavior such as stress-strain response, shear strength, resistance to liquefaction, modulus, and shear wave velocity of granular mixes containing coarse and fine grains is dependent on intergrain contact density of the soil. The global void ratio e is a poor index of contact density for such soils. The contact density depends on void ratio, fine grain content （Cv）, size disparity between particles, and gradation among other factors. A simple analysis of a two-sized particle system with large size disparity is used to develop an understanding of the effects of Cv, e, and gradation of coarse and fine grained soils in the soil mix on intergrain contact density. An equivalent intergranular void ratio （ec）oq is introduced as a useful intergrain contact density for soils at fines content of less than a threshold value Crth. Beyond this value, an equivalent interfine void ratio （ef）eq is introduced as a primary intergrain contact density index. At higher values of Cv beyond a limiting value of fine grains content CVL, an interfine void ratio ef is introduced as the primary contact density index. Relevant equivalent relative density indices （Drc）eq and （Drf）eq are also presented. Experimental data show that these new indices correlate well with steady state strength, liquefaction resistance, and shear wave velocities of sands, silty sands, sandy silts, and gravelly sand mixes.  相似文献   

12.
Based on the liquefaction performance of sites with seismic activity, the normalized shear wave velocity, Vs1, has been proposed as a field parameter for liquefaction prediction. Because shear wave velocity, Vs, can be measured in the field with less effort and difficulty than other field tests, its use by practitioners is highly attractive. However, considering that its measurement is associated with small strain levels, of the order of 10−4–10−3%, Vs reflects the elastic stiffness of a granular material, hence, it is mainly affected by soil type, confining pressure and soil density, but it is insensitive to factors such as overconsolidation and pre-shaking, which have a strong influence on the liquefaction resistance. Therefore, without taking account of the important factors mentioned above, the correlation between shear wave velocity and liquefaction resistance is weak.In this paper, laboratory test results are presented in order to demonstrate the significant way in which OCR (overconsolidation ratio) affects both shear wave velocity and liquefaction resistance. While Vs is insensitive to OCR, the liquefaction resistance increases significantly with OCR. In addition, the experimental results also confirm that Vs correlates linearly with void ratio, regardless of the maximum and minimum void ratios, which means that Vs is unable to give information about the relative density. Therefore, if shear wave velocity is used to predict liquefaction potential, it is recommended that the limitations presented in this paper be taken into account.  相似文献   

13.
Laboratory cyclic triaxial tests were performed to investigate the effect of fine content on the pore pressure generation in sand. Strain-controlled, consolidated undrained tests have been performed with a cyclic shear strain range of 0·015-1·5%. These tests were carried to 1000 cycles or to initial liquefaction, which ever occurred first. Triaxial tests were performed on pure sand silt specimens and specimens with silt additions of 10, 20, 30, and 60% by weight. Two types of silt, a non-plastic silt and a low plasticity silt (PI 10) were used as control materials. The main parameters varied in this study were the amount of silt, the plasticity index of silt, and the void ratio where the observed parameter was the pore pressure generation. For all silt contents, silt plasticity and the number of loading cycles have no significant effect at strain levels below 0·01%. Therefore, threshold strain for silty sands have approximately the same value as sands. For both non-plastic and low plasticity silts, there is a significant increase in the generated pore pressure at high strain levels.  相似文献   

14.
To identify the effect of non-plastic silt on the cyclic behavior of sand–silt mixtures, total sixty undrained cyclic triaxial stress-control tests were carried out on sand–silt mixtures. These tests were conducted on specimens of size 71 mm diameter and 142 mm height with a frequency of 1 Hz. Specimens were prepared at a constant relative density and constant density approach. The effect of relative density, confining pressure as well as magnitude of cyclic loading was also studied. For a constant relative density (Dr=60%) the effect of limiting silt content, pore pressure response and cyclic strength was observed. The rate of generation of excess pore water pressure with respect to cycles of loading was found to initially increase with increase in silt content till the limiting silt content and thereafter it reverses its trend when the specimens were tested at a constant relative density. The cyclic resistance behavior was observed to be just opposite to the pore pressure response. Permeability, CRR and secant shear modulus decreased till limiting silt content; after that they became constant with increasing silt content.  相似文献   

15.
This paper is a systematic effort to clarify why field liquefaction charts based on Seed and Idriss׳ Simplified Procedure work so well. This is a necessary step toward integrating the states of the art (SOA) and practice (SOP) for evaluating liquefaction and its effects. The SOA relies mostly on laboratory measurements and correlations with void ratio and relative density of the sand. The SOP is based on field measurements of penetration resistance and shear wave velocity coupled with empirical or semi-empirical correlations. This gap slows down further progress in both SOP and SOA. The paper accomplishes its objective through: a literature review of relevant aspects of the SOA including factors influencing threshold shear strain and pore pressure buildup during cyclic strain-controlled tests; a discussion of factors influencing field penetration resistance and shear wave velocity; and a discussion of the meaning of the curves in the liquefaction charts separating liquefaction from no liquefaction, helped by recent full-scale and centrifuge results. It is concluded that the charts are curves of constant cyclic strain at the lower end (Vs1<160 m/s), with this strain being about 0.03–0.05% for earthquake magnitude, Mw≈7. It is also concluded, in a more speculative way, that the curves at the upper end probably correspond to a variable increasing cyclic strain and Ko, with this upper end controlled by overconsolidated and preshaken sands, and with cyclic strains needed to cause liquefaction being as high as 0.1–0.3%. These conclusions are validated by application to case histories corresponding to Mw≈7, mostly in the San Francisco Bay Area of California during the 1989 Loma Prieta earthquake.  相似文献   

16.
Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversial issues. This paper presents the results of an experimental evaluation to address these issues. Two parameters, namely, equivalent intergranular void ratio (ec)eq and equivalent interfine void ratio (ef)eq, proposed in a companion paper (Thevanayagam, 2007) as indices of active grain contacts in a granular mix, are used to characterize liquefaction resistance of sands and silty sands. Results indicate that, at the same global void ratio (e), liquefaction resistance of silty sand decreases with an increase in fines content (CF) up to a threshold value (CFth). This is due to a reduction in intergrain contact density between the coarse grains. Beyond CFth, with further addition of fines, the interfine contacts become significant while the inter-coarse grain contacts diminish and coarse grains become dispersed. At the same e, the liquefaction resistance increases and the soil becomes stronger with a further increase in silt content. Beyond a limiting fines content (CFL), the liquefaction resistance is controlled by interfine contacts only. When CFCFth, at the same (ef)eq, the cyclic strength of a sandy silt is comparable to the host silt at a void ratio equal to (ef)eq.  相似文献   

17.
Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversial issues. This paper presents the results of an experimental evaluation to address these issues. Two parameters, namely, equivalent intergranular void ratio (ec)eq and equivalent interfine void ratio (ef)eq, proposed in a companion paper (Thevanayagam, 2007) as indices of active grain contacts in a granular mix, are used to characterize liquefaction resistance of sands and silty sands. Results indicate that, at the same global void ratio (e), liquefaction resistance of silty sand decreases with an increase in fines content (CF) up to a threshold value (CFth). This is due to a reduction in intergrain contact density between the coarse grains. Beyond CFth, with further addition of fines, the interfine contacts become significant while the inter-coarse grain contacts diminish and coarse grains become dispersed. At the same e, the liquefaction resistance increases and the soil becomes stronger with a further increase in silt content. Beyond a limiting fines content (CFL), the liquefaction resistance is controlled by interfine contacts only. When CF＜CFth, at the same (ec)eq, the liquefaction resistance of silty sand is comparable to that of the host clean sand at a void ratio equal to (ec)eq. When CF＞CFth, at the same (ef)eq, the cyclic strength of a sandy silt is comparable to the host silt at a void ratio equal to (ef)eq.  相似文献   

18.
The liquefaction potential of soils is traditionally assessed through geotechnical approaches based on the calculation of the cyclical stress ratio (CSR) induced by the expected earthquake and the ‘resistance’ provided by the soil, which is quantified through standard penetration (SPT), cone penetration (CPT), or similar tests. In more recent years, attempts to assess the liquefaction potential have also been made through measurement of shear wave velocity (VS) in boreholes or from the surface. The latter approach has the advantage of being non-invasive and low cost and of surveying lines rather than single points. However, the resolution of seismic surface techniques is lower than that of borehole techniques and it is still debated whether it is sufficient to assess the liquefaction potential.In this paper we focus our attention on surface seismic techniques (specifically the popular passive and active seismic techniques based on the correlation of surface waves such as ReMiTM, MASW, ESAC, SSAP, etc.) and explore their performance in assessing the liquefaction susceptibility of soils. The experimental dataset is provided by the two main seismic events of ML=5.9 and 5.8 (MW=6.1, MW=6.0) that struck the Emilia-Romagna region (Northern Italy) on May 20 and 29, 2012, after which extensive liquefaction phenomena were documented in an area of 1200 km2.The CPT and drillings available in the area allow us to classify the soils into four classes: A) shallow liquefied sandy soils, B) shallow non-liquefied sandy soils, C) deep non-liquefied sandy soils, and D) clayey–silty soils, and to determine that on average class A soils presented a higher sand content at the depth of 5–8 m compared to class B soils, where sand was dominant in the upper 5 m. Surface wave active–passive surveys were performed at 84 sites, and it was found that they were capable of discriminating among only three soil classes, since class A and B soils showed exactly the same VS distribution, and it is possible to show both experimentally and theoretically that they appear not to have sufficient resolution to address the seismic liquefaction issue.As a last step, we applied the state-of-the art CSR–VS method to assess the liquefaction potential of sandy deposits and we found that it failed in the studied area. This might be due to the insufficient resolution of the surface wave methods in assessing the Vs of thin layers and to the fact that Vs scales with the square root of the shear modulus, which implies an intrinsic lower sensitivity of Vs to the shear resistance of the soil compared to parameters traditionally measured with the penetration tests. However, it also emerged that the pure observation of the surface wave dispersion curves at their simplest level (i.e. in the frequency domain, with no inversion) is still potentially informative and can be used to identify the sites where more detailed surveys to assess the liquefaction potential are recommended.  相似文献   

19.
Mechanical behavior such as stress-strain response, shear strength, resistance to liquefaction, modulus, and shear wave velocity of granular mixes containing coarse and fine grains is dependent on intergrain contact density of the soil. The global void ratio e is a poor index of contact density for such soils. The contact density depends on void ratio, fine grain content (CF), size disparity between particles, and gradation among other factors. A simple analysis of a two-sized particle system with large size disparity is used to develop an understanding of the effects of CF , e, and gradation of coarse and fine grained soils in the soil mix on intergrain contact density. An equivalent intergranular void ratio (ec)eq is introduced as a useful intergrain contact density for soils at fines content of less than a threshold value CFth. Beyond this value, an equivalent interfine void ratio (ef)eq is introduced as a primary intergrain contact density index. At higher values of CF beyond a limiting value of fine grains content CFL, an interfine void ratio ef is introduced as the primary contact density index. Relevant equivalent relative density indices (Drc)eq and (Drf)eq are also presented. Experimental data show that these new indices correlate well with steady state strength, liquefaction resistance, and shear wave velocities of sands, silty sands, sandy silts, and gravelly sand mixes.  相似文献   

20.
Mechanical behavior such as stress-strain response, shear strength, resistance to liquefaction, modulus, and shear wave velocity of granular mixes containing coarse and fine grains is dependent on intergrain contact density of the soil. The global void ratio e is a poor index of contact density for such soils. The contact density depends on void ratio, fine grain content (CF), size disparity between particles, and gradation among other factors. A simple analysis of a two-sized particle system with large size disparity is used to develop an understanding of the effects of CF, e, and gradation of coarse and fine grained soils in the soil mix on intergrain contact density. An equivalent intergranular void ratio (ec)eq is introduced as a useful intergrain contact density for soils at fines content of less than a threshold value CFth. Beyond this value, an equivalent interfine void ratio (ef)eq is introduced as a primary intergrain contact density index. At higher values of CF beyond a limiting value of fine grains content CFL, an interfine void ratio ef is introduced as the primary contact density index. Relevant equivalent relative density indices (Drc)eq and (Drf)eq are also presented. Experimental data show that these new indices correlate well with steady state strength, liquefaction resistance, and shear wave velocities of sands, silty sands, sandy silts, and gravelly sand mixes.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号