首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Synthetic pyrite crystals doped with As, Co, or Ni, undoped pyrite, and natural arsenian pyrite from Leadville, Colorado were investigated with electrochemical techniques and solid-state measurements of semiconducting properties to determine the effect of impurity content on pyrite’s oxidation behavior. Potential step experiments, cyclic voltammetry, and AC voltammetry were performed in a standard three-electrode electrochemical cell setup. A pH 1.78 sulfuric acid solution containing 1 mM ferric iron, open to atmospheric oxygen, was chosen to approximate water affected by acid drainage. Van der Pauw/Hall effect measurements determined resistivity, carrier concentration and carrier mobility.The anodic dissolution of pyrite and the reduction of ferric iron half-reactions are taken as proxies for natural pyrite oxidation. Pyrite containing no impurities is least reactive. Pyrite with As is more reactive than pyrite with either Ni or Co despite lower dopant concentration. As, Co, and Ni impurities introduce bulk defect states at different energy levels within the band gap. Higher reactivity of impure pyrite suggests that introduced defect levels lead to higher density of occupied surface states at the solid-solution interface and increased metallic behavior. The current density generated from potential step experiments increased with increasing As concentration. The higher reactivity of As-doped pyrite may be related to p-type conductivity and corrosion by holes. The results of this study suggest that considering the impurity content of pyrite in mining waste may lead to more accurate risk assessment of acid producing potential.  相似文献   

2.
Macroscopic pyrite crystals originating from a variety of geologic settings were made into thick sections. Electrical properties were measured with a Hall system, and minor element composition was analyzed with laser ablation inductively coupled plasma mass spectroscopy (LA-ICPMS). Selected thick sections were oxidized in a moist air environment inside a glove chamber. The relative metal content of surface products formed during oxidation was analyzed by LA-ICP-MS. Natural pyrite exhibits a range of electrical properties corresponding to the content of the common minor elements Co, As and Ni. These properties are similar to those of synthetic pyrite doped with single elements. Pyrite enriched in Co is an n-type semiconductor with low resistivity and high carrier mobility, while arsenian pyrite tends to be p-type and have higher resistivity. The effect of Ni is weaker and tends to be obscured by Co and As in samples of mixed composition. Cobalt demonstrates the strongest effect on electrical properties. Enrichment of Co at oxidized pyrite surfaces is inversely correlated with its concentration in the underlying pyrite. Cobalt enrichment in oxidation products is also more pronounced along crystal defects such as fractures, and in crystals with heterogeneous distribution of trace elements. These observations might be explained by differences in the electronic structure of pyrite arising from the presence of impurities, and by the distribution of domains with different impurity compositions, facilitating electron transfer.  相似文献   

3.
The effect of heat and illumination with visible light on the oxidation of pyrite with dissolved molecular oxygen in solutions between pH 2 and 6 has been investigated using a combination of surface science experiments and batch oxidation experiments. The rate of the oxidation of pyrite is strongly dependent on temperature. It is, however, not possible to cast the temperature dependence in a simple Arrhenius equation because the magnitude of the activation energy depends on the progress variable chosen. Activation energies based on proton release rate, sulfate release rate, and total iron release rate vary by as much as 40 kJ mol-1, suggesting that the oxidation mechanism of the sulfur and iron component of pyrite are largely independent of each other. This difference in mechanism can also explain why the reaction rates on the basis of these three different progress variables do not show the same pH dependence. Exposed to visible light, the rate of pyrite oxidation is under most conditions accelerated by less than a factor of two. Some of this acceleration may be accounted for by a light-induced heating of the pyrite surface. Surface science experiments employing photoelectron spectroscopy show no evidence for significant changes in the chemical composition of the surface as a function of exposure to visible light. The batch sorption experiments show, however, that the reaction stoichiometry changes somewhat, which indicates that there might be a change in reaction mechanism as a result of exposure to visible light.  相似文献   

4.
The abiotic oxidative dissolution behaviors of eight natural pyrite samples, five sedimentary and three hydrothermal, from various geological environments were compared under oxic conditions at pH 3 and 6 in a highly controlled batch reactor dissolution system. The three sedimentary pyrite samples associated with coal had greater specific surface areas and also exhibited greater apparent dissolution rates and extent than the other two sedimentary and three hydrothermal samples under both pH conditions. However, after normalizing for surface area, the dissolution rate constants for the different pyrite samples were similar; the greatest difference was between the two non-coal sedimentary pyrite samples. Pyrite morphology and the presence of trace metals could contribute to the differences in dissolution behavior as reflected in the normalized dissolution rates. The sulfur:iron ratio observed in the aqueous solution at pH 3 increased with time, but was always less than 2.0 (predicted from the stoichiometry of dissolution) for all the pyrite samples during the 24-h experimental duration. This can be explained by the disproportionation dissociation of thiosulfate, an initial product of pyrite dissolution, to elemental sulfur and sulfate which does not occur in a 1:1 ratio. The results of this work indicate the importance of extracting and using the specific pyrite(s) relevant to particular mining areas in order to understand pyrite dissolution rates and the influence of environmental conditions on those rates.  相似文献   

5.
The nature of the surface oxidation phase on pyrite, FeS2, reacted in aqueous electrolytes at pH = 2 to 10 and with air under ambient atmospheric conditions was studied using synchrotron-based oxygen K edge, sulfur LIII edge, and iron LII,III edge X-ray absorption spectroscopy. We demonstrate that O K edge X-ray absorption spectra provide a sensitive probe of sulfide surface oxidation that is complementary to X-ray photoelectron spectroscopy. Using total electron yield detection, the top 20 to 50 Å of the pyrite surface is characterized. In air, pyrite oxidizes to form predominantly ferric sulfate. In aqueous air-saturated solutions, the surface oxidation products of pyrite vary with pH, with a marked transition occurring around pH 4. Below pH = 4, a ferric (hydroxy)sulfate is the main oxidation product on the pyrite surface. At higher pH, we find iron(III) oxyhydroxide in addition to ferric (hydroxy)sulfate on the surface. Under the most alkaline conditions, the O K edge spectrum closely resembles that of goethite, FeOOH, and the surface is oxidized to the extent that no FeS2 can be detected in the X-ray absorption spectra. In a 1.667 × 10−3 mol/L Fe3+ solution with ferric iron present as FeCl3 in NaCl, the oxidation of pyrite is autocatalyzed, and formation of the surface iron(III) oxyhydroxide phase is promoted at low pH.  相似文献   

6.
Based on back scattered electron images and electron micro-probe analysis results, four alteration layers, including a transition layer, a reticulated ferric oxide layer, a nubby ferric oxide layer and a cellular ferric oxide layer, were identified in the naturally weathering products of pyrite. These layers represent a progressive alteration sequence of pyrite under weathering conditions. The cellular ferric oxide layer correlates with the strongest weathering phase and results from the dissolution of nubby ferric oxide by acidic porewater. Leaching coefficient was introduced to better express the response of element mobility to the degree of pyrite weathering. Its variation shows that the mobility of S, Co and Bi is stronger than As, Cu and Zn. Sulfur in pyrite is oxidized to sulfuric acid and sulfate that are basically released into to porewater, and heavy metals Co and Bi are evidently released by acid dissolution. As, Cu and Zn are enriched in ferric oxide by adsorption and by co-precipitation, but they would re-release to the environment via desorption or dissolution when porewater pH becomes low enough. Consequently, Co, Bi, As, Cu and Zn may pose a substantial impact on water quality. Considering that metal mobility and its concentration in mine waste are two important factors influencing heavy metal pollution at mining-impacted sites, Bi and Co are more important pollutants in this case.  相似文献   

7.
This study focuses on denitrification in a sandy aquifer using geochemical analyses of both sediment and groundwater, combined with groundwater age dating (3H/3He). The study sites are located underneath cultivated fields and an adjacent forested area at Oostrum, The Netherlands. Shallow groundwater in the region has high nitrate concentrations (up to 8 mM) due to intense fertilizer application. Nitrate removal from the groundwater below cultivated fields correlates with sulfate production, and the release of dissolved Fe2+ and pyrite-associated trace metals (e.g. As, Ni, Co and Zn). These results, and the presence of pyrite in the sediment matrix within the nitrate removal zone, indicate that denitrification coupled to pyrite oxidation is a major process in the aquifer. Significant nitrate loss coupled to sulfate production is further confirmed by comparing historical estimates of regional sulfate and nitrate loadings to age-dated groundwater sulfate and nitrate concentrations, for the period 1950-2000. However, the observed increases in sulfate concentration are about 50% lower than would be expected from complete oxidation of pyrite to sulfate, possibly due to the accumulation of intermediate oxidation state sulfur compounds, such as elemental sulfur. Pollutant concentrations (NO3, Cl, As, Co and Ni) measured in the groundwater beneath the agricultural areas in 1996 and 2006 show systematic decreases most likely due to declining fertilizer use.  相似文献   

8.
《Chemical Geology》2006,225(1-2):16-29
Pyrite oxidation rates were examined at various concentrations of dissolved oxygen (DO) in the presence of the sulfur and iron oxidizer Acidithiobacillus ferrooxidans. Five different batch experiments were performed at room temperature for 75 days under various DO levels (273, 129, 64.8, 13.2, and ≤ 0.006 μM), containing pyrite grains (particle size 63–250 μm) and a modified 9K nutrient medium at pH 3. The reactors were inoculated with A. ferrooxidans. In all experiments, pH decreased with time and sulfur and iron were released to the solution, indicating pyrite oxidation at all DO levels. Pyrite oxidation rates (ca. 5 × 10− 10 mol m− 2 s− 1 at 273 μM DO) from all experiments showed positive correlation with DO, Fe(III), and bacterial concentration. These rates were significantly slower than rates presented in other published studies, but this is probably due to the significantly greater Fe(III) concentration at lower pH in these previous studies. The results obtained in this study suggest that ferric iron reduction at the pyrite surface is the primarily mechanism for microbial pyrite oxidation in the presence of DO. The results from our study support the indirect mechanism of sulfide oxidation, where A. ferrooxidans oxidizes ferrous iron in the presence of DO, which then oxidizes pyrite.  相似文献   

9.
The adsorption of ethyl, propyl and butyl xanthates on pyrite has been studied through electrokinetics, batch adsorption tests, and quantification of Fe2+ ions in solution. Adsorption isotherms for the three alkyl xanthates indicate that their adsorption to dixanthogen produces Fe2+ ions in solution and decreases the pyrite zeta potential negatively. It seems that the oxidation reaction of xanthates to dixanthogen on pyrite is coupled with the reduction reaction of surface-ferric hydroxide to ferrous ions, leading to the dissolution of hydrophilic ferric hydroxide and growth of hydrophobic dixanthogen on the surface of pyrite. Flotation of pyrite is presented as a function of pH using various ethyl xanthate concentrations. The floatability results are explained in terms of the surface coverage relationship between ferric hydroxide and dixanthogen, which is pH dependent.  相似文献   

10.
Naturally occurring pyrite commonly contains minor substituted metals and metalloids (As, Se, Hg, Cu, Ni, etc.) that can be released to the environment as a result of its weathering. Arsenic, often the most abundant minor constituent in pyrite, is a sensitive monitor of progressive pyrite oxidation in coal. To test the effect of pyrite composition and environmental parameters on the rate and extent of pyrite oxidation in coal, splits of five bituminous coal samples having differing amounts of pyrite and extents of As substitution in the pyrite, were exposed to a range of simulated weathering conditions over a period of 17 months. Samples investigated include a Springfield coal from Indiana (whole coal pyritic S = 2.13 wt.%; As in pyrite = detection limit (d.l.) to 0.06 wt.%), two Pittsburgh coal samples from West Virginia (pyritic S = 1.32–1.58 wt.%; As in pyrite = d.l. to 0.34 wt.%), and two samples from the Warrior Basin, Alabama (pyritic S = 0.26–0.27 wt.%; As in pyrite = d.l. to 2.72 wt.%). Samples were collected from active mine faces, and expected differences in the concentration of As in pyrite were confirmed by electron microprobe analysis. Experimental weathering conditions in test chambers were maintained as follows: (1) dry Ar atmosphere; (2) dry O2 atmosphere; (3) room atmosphere (relative humidity ∼20–60%); and (4) room atmosphere with samples wetted periodically with double-distilled water. Sample splits were removed after one month, nine months, and 17 months to monitor the extent of As and Fe oxidation using As X-ray absorption near-edge structure (XANES) spectroscopy and 57Fe Mössbauer spectroscopy, respectively. Arsenic XANES spectroscopy shows progressive oxidation of pyritic As to arsenate, with wetted samples showing the most rapid oxidation. 57Fe Mössbauer spectroscopy also shows a much greater proportion of Fe3+ forms (jarosite, Fe3+ sulfate, FeOOH) for samples stored under wet conditions, but much less difference among samples stored under dry conditions in different atmospheres. The air-wet experiments show evidence of pyrite re-precipitation from soluble ferric sulfates, with As retention in the jarosite phase. Extents of As and Fe oxidation were similar for samples having differing As substitution in pyrite, suggesting that environmental conditions outweigh the composition and amount of pyrite as factors influencing the oxidation rate of Fe sulfides in coal.  相似文献   

11.
This study examines the dynamics of sulfur and trace elements (As, Co, Mo, Ni, Ti and Zn) when brackish-water sediments, unusually rich in metastable iron sulfide (probably a mixture of mackinawite and greigite), are brought into the oxidation zone by postglacial isostatic land uplift and farmland drainage. When subaqueous sediments approach the sea level, metastable iron sulfide is oxidized in the upmost layers and pyrite preserved and even accumulated concomitantly trapping Co, Ni and Zn but not As and Mo. When the land uplift has brought the sediments above sea level and natural drainage thus is initiated, the pyrite is oxidized and Co, Ni and Zn are released and transported down the profile. If this setting remained undisturbed, the slightly oxidized sediment (unripe soil) would become covered by peat and thus protected from further oxidation and metal translocation. Often these sediments are, however, artificially drained resulting in extensive oxidation and fast soil-profile development. The soil is an acid sulfate (AS) soil, characterized by low pH (<4), extensive leaching of metals and an abundance of disseminated brownish Fe(III) precipitates. We suggest that the fast soil development is due to initial oxidation of metastable iron sulfide, followed by pyrite oxidation. Drain bottom sediment, which in terms of chemistry and S-isotopes resembled that of the surfacing sea bottom strata, acted during the sampling period as a sink for metals. The abundant preservation of metastable iron sulfide below the groundwater table, even long periods after uplift above the sea level, is a puzzling feature. We suggest that it is the net result of sulfur starvation, an abundance of Fe(II) and strongly reducing conditions.  相似文献   

12.
含金黄铁矿在细菌氧化、化学氧化过程中,除生成高铁的硫酸盐和硫酸外,还生成了亚铁的硫酸盐及硫的低价氧化物,体系中的电位较低,距溶解自然金呈Au(SO_4)_2~-所需电位甚远,实验表明,金不溶于硫酸铁溶液中。当氧化程度加深,介质pH>4,黄铁矿氧化产生的硫代硫酸根可稳定存在时,自然金呈稳定的硫代硫酸盐配合物溶解。  相似文献   

13.
Metals released from oxidation and weathering of sulphide minerals in mine tailings are to a high degree retained at deeper levels within the tailings themselves. To be able to predict what could happen in the future with these secondarily retained metals, it is important to understand the retention mechanisms. In this study an attempt to use laser ablation high-resolution ICP-MS (LA-ICP-SMS) to quantify enrichment of trace elements on pyrite surfaces in mine tailings was performed. Pyrite grains were collected from a profile through the pyrite-rich tailings at the Kristineberg mine in northern Sweden. At each spot hit by the laser, the surface layer was analyzed in the first shot, and a second shot on the same spot gave the chemical composition of the pyrite immediately below. The crater diameter for a laser shot was known, and by estimating the crater depth and total pyrite surface, the total enrichment on pyrite grains was calculated. Results are presented for As, Cd, Co, Cu, Ni and Zn. The results clearly show that there was an enrichment of As, Cd, Cu and Zn on the pyrite surfaces below the oxidation front in the tailings, but not of Co and Ni. Arsenic was also enriched on the pyrite grains that survived in the oxidized zone. Copper has been enriched on pyrite surfaces in unoxidized tailings in the largest amount, followed by Zn and As. However, only 1.4 to 3.1% of the Cd and Zn released by sulphide oxidation in the oxidized zone have been enriched on the pyrite surfaces in the unoxidized tailings, but for As and Cu corresponding figures are about 64 and 43%, respectively. There were many uncertainties in these calculations, and the results shall not be taken too literally but allowed the conclusion that enrichment on pyrite surfaces is an important process for retention of As and Cu below the oxidation front in pyrite rich tailings. Laser ablation is not a surface analysis technique, but more of a thin layer method, and gives no information on the type of processes resulting in enrichment on the pyrite surfaces. Although only pyrite grains that appeared to be fresh and without surface coatings were used in this study, the possibility that a thin layer of Fe-hydroxides occurred must be considered. Both adsorption to the pyrite directly or to Fe-oxyhydroxides may explain the enrichment of As, Cd, Cu and Zn on the pyrite surfaces, and, in the case of Cu, also the replacement of Fe(II) by Cu(II) in pyrite.  相似文献   

14.
A survey of hot, acid springs in Yellowstone Park has shown that high concentrations of ferrous and ferric iron are often present. Total ionic iron concentrations in different springs ranged from less than 1 ppm to greater than 200 ppm, and up to 50% of the ionic iron was in the ferrous form. Some of these springs also have high concentrations of reduced sulfur species (S2? and S0). Significant populations of the bacterium Sulfolobus, acidocaldarius, an autotrophic organism able to live and oxidize sulfur compounds at low pH and high temperature, were present in most of these springs. The role of this organism in the oxidation of ferrous iron was investigated by incubating natural samples of water and assaying for disappearance of ferrous iron. Controls in which bacterial activity was inhibited by addition of 10% NaCl were also run. Bacterial oxidation of ferrous iron occurred in most but not all of the spring waters. The temperature optimum for oxidation varied from spring to spring, but significant oxidation occurred at temperatures of 80–85°C, but not at 90°C. Thus, 85–90°C is the upper temperature at which bacterial iron oxidation occurs; a similar upper limit has previously been reported for sulfur oxidation in the same kinds of springs. The steady-state concentrations of ferrous and ferric iron are determined by the rate at which these ions move into the spring pools with the ground water (flow rate), by the rate at which ferric iron is reduced to the ferrous state by sulfide, and by the rate of bacterial oxidation. The bacterial oxidation rate is faster than the flow rate, so that the rate of reduction of ferric iron is probably the rate-controlling reaction. In several springs, no decrease in ferrous iron occurred, even though high bacterial populations were present. It was shown that in these springs, ferrous iron oxidation occurred but the ferric iron formed was reduced back to the ferrous state again. These springs were all high in suspended sediment and the reductant was shown to be present in the sediment. X-ray diffraction revealed that the sediment contained three major ingredients, elemental sulfur, natroalunite, and quartz. Chemical analyses showed a small amount of sulfide, too little to reduce the ferric iron. Elemental sulfur itself did not reduce ferric iron but when elemental sulfur was removed from the sediment by CS2 extraction, the activity of the sediment was abolished. It is hypothesized that the sulfide present in the sediment (possibly bound to natroalunite) reacts with elemental sulfur to form a reductant for ferric iron. The results show that bacteria can have a profound influence on the ferrous/ferric ratios of geothermal systems, but that temperature and mineral composition of the water may significantly influence the overall result.  相似文献   

15.
吴昊  祝向平  贾强  张彬  李勇  杨礼创 《地质学报》2023,97(7):2261-2280
黄铁矿在自然环境中极易发生氧化,造成严重生态环境问题。为了研究自然条件下不同粒度和晶形黄铁矿化学成分的差异对黄铁矿氧化速率的影响,本文对巴达铜金矿床黄铁矿进行了LA- ICP- MS原位主微量元素分析和矿物面扫描分析。测试结果表明粗粒黄铁矿S、Fe含量较高,成分更纯;微量元素As、Co、Ni和Pb、Cu、Zn分别以类质同象方式和包裹体形式更多地存在于细粒黄铁矿中,二者均能促使细粒黄铁矿氧化速率加快;粗粒黄铁矿中Cr和Ti元素含量较高,其氧化后生成致密氧化膜可抑制黄铁矿被进一步氧化。本文认为对于本矿床中粗粒黄铁矿和细粒黄铁矿氧化污染问题应采用两种不同的治理措施,对于不易被氧化的粗粒黄铁矿,使其处于常温常压的干燥避光环境中即可防止发生氧化;对于易氧化的细粒黄铁矿,其氧化产物造成污染对环境压力较大,应采用源头治理和末端治理相结合的措施进行处理,以达到更科学的治理效果。  相似文献   

16.
山西堡子湾金矿床黄铁矿标型特征   总被引：6，自引：1，他引：6  
从成因矿物学及找矿矿物学观点出发，系统研究了堡子湾金矿床黄铁矿的产状，形态，化学成分，热电性质和热爆特征，该矿床黄铁矿富含Co,Ni,As,Ag,Au与W，Cu,Hg,Ag，As，Bi,Ni,Co,Pb相关性较好，构成特征元素组合，与通常认为的与火山－次火山热液有关的明矾石－高岭土型浅成中低温热液型金矿床特征元素及其组合基本一致。黄铁矿空穴型导电性与明矾，石－高岭土型浅成中低温热液型金矿床特征元素圾其组合基本一致。黄铁矿空穴型导电性与As,Au正相关，与Co，Ni呈明显的负相关，P型和N型导电性是由As/(Co Ni)值决定的。利用黄铁矿热电性及热爆特征空间分带与赋矿空间的对应关系进行成矿预测，效果明显。  相似文献   

17.
柱子淋洗模拟研究磷酸铁膜抑制黄铁矿氧化效果   总被引：1，自引：0，他引：1  
自然室温条件下用柱子淋洗模拟研究了接氧化亚铁硫杆菌（Ｔｈｉｏｂａｃｉｌｌｕｓ ｆｅｒｒｏｏｘｉｄａｎｓ,简称Ｔ．Ｆ菌）时磷酸铁膜抑制黄铁矿氧化的效果。试验结果首次指出：用ＫＨ２ＰＯ４与Ｈ２Ｏ２淋洗黄铁矿,在其表面形成的磷酸铁膜不能抑制黄铁矿的生物氧化,反而在一定程度上加速其氧化进程。经包膜后的黄铁矿矿石柱子间歇循环淋洗一年后的收集液中ＳＯ４＾２－累积量高达３３７５６．１ｍｇ;为对照组的１．６倍,是  相似文献   

18.
Experimental investigations on pyrite synthesis indicate that before pyrite can be produced by a reaction involving ferrous iron, the disulphide ion must be formed; in experiments described the ion was obtained by the action of H2S in aqueous solution on elemental sulphur. Conditions under which the experiments were conducted indicate that pyrite will not form above pH 6.0. The reaction to produce pyrite is fastest when oxygen is excluded and elemental sulphur is produced from the oxidation of H2S by ferric iron. A reaction between FeS and elemental sulphur will yield pyrite at a much slower rate, although the same basic reaction is involved. An attempt has been made to relate the occurrence of pyrite in different sedimentary environments to this basic chemistry.
Zusammenfassung Wie Versuche zeigen, ist die Voraussetzung der Pyrit-Bildung das Vorliegen von S 2 2– -Ionen, die dann mit FeII reagieren. Die S 2 2– -Ionen wurden durch Einwirken einer verdünnten H2S-Lösung auf elementaren Schwefel erhalten. Pyrite entstehen in diesen Experimenten somit nur unterhalb pH 6. Pyrit erhält man am schnellsten, wenn Sauerstoff abwesend ist und der H2S durch FeIII oxidiert wird. Die Umsetzung von FeS mit elementarem Schwefel liefert Pyrit wesentlich langsamer, wenn auch die zugrunde liegenden Reaktionen sich entsprechen. Es wird versucht, sedimentäre Pyrit-Vorkommen entsprechend diesen Reaktionsabläufen zu deuten.
  相似文献   

19.
刘仕玉  刘玉平  叶霖  王大鹏 《岩石学报》2021,37(4):1196-1212
滇东南马关都龙是一个以锡锌为主,共-伴生铟、铜、铅、钨、铁、银等多种元素的锡锌多金属超大型矿床。虽然前人从矿物学、矿床地球化学、年代学等不同角度开展了较多的研究,该矿床锡锌多金属矿化为燕山晚期岩浆热液活动的产物已是不争的事实,但关于该矿床是否存在热水沉积作用及其与锡锌多金属成矿作用的关系依然存在较大争议。本文选取都龙矿区广泛存在的黄铁矿作为主要研究对象,在矿相学基础上利用LA-ICPMS对不同阶段黄铁矿的微量元素组成开展了系统的研究。野外及显微鉴定结果表明,矿区存在四种类型(期次)的黄铁矿,即:鲕状黄铁矿Py1;穿切或交代Py1的细脉状黄铁矿Py2;与闪锌矿等硫化物共生的自形黄铁矿Py3;包裹早期黄铁矿或闪锌矿等硫化物的他形黄铁矿Py4。LA-ICPMS分析结果表明,该矿床黄铁矿中富集多种微量元素,其中Co、Ni、As、Ge等元素以类质同象的形式存在黄铁矿晶格中,而其余元素多以显微矿物包体形式赋存于黄铁矿中。上述四期黄铁矿微量元素组成存在较大差别,Py1相对富集Zn和As,而其余微量元素含量较低,Co与Ni含量较低,Co/Ni比值远低于1.00,其微量元素组成与典型沉积作用形成黄铁矿基本一致; Py2与Py1具有相似的微量元素组成特征,其Co/Ni比值接近Py1变化范围; Py3和Py4除富集Zn、As外,Mn、Co、Ni、Cu、Sb、Pb、Bi元素含量也相对较高,其Co/Ni比值相对较高,多大于1,与典型岩浆热液型黄铁矿微量元素组成相似,而与沉积型黄铁矿差异明显。结合各阶段黄铁矿产出地质特征,对比不同类型黄铁矿微量元素组成,本研究认为:Py1鲕状黄铁矿为热水沉积作用形成; Py2为Py1变质改造形成的细脉状黄铁矿,其微量元素继承了Py1; Py3为岩浆热液活动形成的自形黄铁矿; Py4为岩浆热液活动晚期形成的他形黄铁矿,Ag和Bi组成作为区分不同成因类型黄铁矿的化学指标的潜力。矿区早期沉积作用形成鲕状黄铁矿过程可能为后期成矿作用提供了部分硫源及少量Zn等成矿物质,海西-印支期区域变质改造作用对矿区成矿作用影响不大,而燕山晚期岩浆热液活动才是矿区锡多金属大规模成矿作用的主导因素。  相似文献   

20.
硫铁矿烧渣制备铁系化工产品研究方法综述   总被引：6，自引：0，他引：6  
硫铁矿烧渣是一种二次资源,对其综合利用正引起广泛重视。目前烧渣的利用主要是围绕着铁系化工产品:铁盐(制取硫酸亚铁、二氯化铁),铁系颜料(制取氧化铁红、氧化铁黄、氧化铁黑),铁氧体材料——高纯磁性氧化铁,净水剂(生产聚合硫酸铁及复合净水剂)。今后,探索硫铁矿烧渣更好的综合利用,将会成为研究热点,这依赖于硫铁矿烧渣浸液中高效除杂剂的筛选和合理的除杂工艺。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号