共查询到20条相似文献，搜索用时 29 毫秒
1.
Silicate and oxide mineral inclusions in diamonds from the geologically and historically important De Beers Pool kimberlites in Kimberley, South Africa, are characterised by harzburgitic compositions (>90%), with lesser abundances from eclogitic and websteritic parageneses. The De Beers Pool diamonds contain unusually high numbers of inclusion intergrowths, with garnet+orthopyroxene±chromite±olivine and chromite+olivine assemblages dominant. More unusual intergrowths include garnet+olivine+magnesite and an eclogitic assemblage comprising garnet+clinopyroxene+rutile. The mineral chemistry of the De Beers Pool inclusions overlaps that of most worldwide localities. Peridotitic garnet inclusions exhibit variable CaO (<5.8 wt.%) and Cr 2O 3 contents (3.0–15.0 wt.%), although the majority are harzburgitic with very low calcium concentrations (<2 wt.% CaO). Eclogitic garnet inclusions are characterised by a wide range in CaO (3.3–21.1 wt.%) with low Cr 2O 3 (<1 wt.%). Websteritic garnets exhibit intermediate compositions. Most chromite inclusions contain 63–67 wt.% Cr 2O 3 and <0.5 wt.% TiO 2. Olivine and orthopyroxene inclusions are magnesium-rich with Mg-numbers of 93–97. Olivine inclusions in chromite exhibit the highest Mg-numbers and also contain elevated Cr 2O 3 contents up to 1.0 wt.%. Peridotitic clinopyroxene inclusions are Cr-diopsides with up to 0.8 wt.% K 2O. Eclogitic and websteritic clinopyroxene inclusions exhibit overlapping compositions with a wide range in Mg-numbers (66–86). Calculated temperatures for non-touching inclusion pairs from individual diamonds range from 1082 to 1320 °C (average=1197 °C), whereas pressures vary from 4.6 to 7.7 GPa (average=6.3 GPa). Touching inclusion assemblages are characterised by equilibration temperatures of 995 to 1182 °C (average=1079 °C) and pressures of 4.2–6.8 GPa (average=5.4 GPa). Provided that the non-touching inclusions represent equilibrium assemblages, it is suggested that these inclusions record the conditions at the time of diamond crystallisation (1200 °C; 3.0 Ga). The lower average temperatures for touching inclusions are attributed to re-equilibration in a cooling mantle (1050 °C) prior to kimberlite eruption at 85 Ma. Pressure estimates for touching garnet–orthopyroxene inclusions are also skewed towards lower values than most non-touching inclusions. This apparent difference may be an artefact of the Al-exchange geobarometer and/or the result of sampling bias, due to limited numbers of non-touching garnet–orthopyroxene inclusions. Alternatively pressure differences could be caused by differential uplift in the mantle or possibly variations in thermal compressibility between diamond and silicate inclusions. However, thermodynamic modelling suggests that thermal compressibility differences would cause only minor changes in internal inclusion pressures (<0.2 GPa/100 °C). 相似文献
2.
In this paper the first fluid-inclusion data are presented from Late Archaean Scourian granulites of the Lewisian complex of mainland northwest Scotland. Pure CO 2 or CO 2-dominated fluid inclusions are moderately abundant in pristine granulites. These inclusions show homogenization temperatures ranging from − 54 to + 10 °C with a very prominent histogram peak at − 16 to − 32 °C. Isochores corresponding to this main histogram peak agree with P-T estimates for granulite-facies recrystallization during the Badcallian (750–800 °C, 7–8 kbar) as well as with Inverian P-T conditions (550–600 °C, 5 kbar). The maximum densities encountered could correspond to fluids trapped during an early, higher P-T phase of the Badcallian metamorphism (900–1000 °C, 11–12 kbar). Homogenization temperatures substantially higher than the main histogram peak may represent Laxfordian reworking (≤ 500 °C, < 4 kbar). In the pristine granulites, aqueous fluid inclusions are of very subordinate importance and occur only along late secondary healed fractures. In rocks which have been retrograded to amphibolite facies from Inverian and/or Laxfordian shear zones, CO 2 inclusions are conspicuously absent; only secondary aqueous inclusions are present, presumably related to post-granulite hydration processes. These data illustrate the importance of CO 2-rich fluids for the petrogenesis of Late Archaean granulites, and demonstrate that early fluid inclusions may survive subsequent metamorphic processes as long as no new fluid is introduced into the system. 相似文献
3.
Mineral inclusions recovered from 100 diamonds from the A154 South kimberlite (Diavik Diamond Mines, Central Slave Craton, Canada) indicate largely peridotitic diamond sources (83%), with a minor (12%) eclogitic component. Inclusions of ferropericlase (4%) and diamond in diamond (1%) represent “undetermined” parageneses. Compared to inclusions in diamonds from the Kaapvaal Craton, overall higher CaO contents (2.6 to 6.0 wt.%) of harzburgitic garnets and lower Mg-numbers (90.6 to 93.6) of olivines indicate diamond formation in a chemically less depleted environment. Peridotitic diamonds at A154 South formed in an exceptionally Zn-rich environment, with olivine inclusions containing more than twice the value (of 52 ppm) established for normal mantle olivine. Harzburgitic garnet inclusions generally have sinusoidal rare earth element (REEN) patterns, enriched in LREE and depleted in HREE. A single analyzed lherzolitic garnet is re-enriched in middle to heavy REE resulting in a “normal” REEN pattern. Two of the harzburgitic garnets have “transitional” REEN patterns, broadly similar to that of the lherzolitic garnet. Eclogitic garnet inclusions have normal REEN patterns similar to eclogitic garnets worldwide but at lower REE concentrations. Carbon isotopic values (δ13C) range from − 10.5‰ to + 0.7‰, with 94% of diamonds falling between − 6.3‰ and − 4.0‰. Nitrogen concentrations range from below detection (< 10 ppm) to 3800 ppm and aggregation states cover the entire spectrum from poorly aggregated (Type IaA) to fully aggregated (Type IaB). Diamonds without evidence of previous plastic deformation (which may have accelerated nitrogen aggregation) typically have < 25% of their nitrogen in the fully aggregated B-centres. Assuming diamond formation beneath the Central Slave to have occurred in the Archean [Westerlund, K.J., Shirey, S.B., Richardson, S.H., Gurney, J.J., Harris, J.W., 2003b. Re–Os systematics of diamond inclusion sulfides from the Panda kimberlite, Slave craton. VIIIth International Kimberlite Conference, Victoria, Canada, Extended Abstracts, 5p.], such low aggregation states indicate mantle residence at fairly low temperatures (< 1100 °C). Geothermometry based on non-touching inclusion pairs, however, indicates diamond formation at temperatures around 1200 °C. To reconcile inclusion and nitrogen based temperature estimates, cooling by about 100–200 °C shortly after diamond formation is required. 相似文献
4.
As is typical of ultra-high pressure (UHP) terrains, the regional extent of the UHP terrain in the Dabieshan of central China is highly speculative, since the volume of eclogites and paragneisses preserving unequivocal evidence of coesite and/or diamond stability is very small. By contrast, the common garnet ( XMn=0.18–0.45)–phengite (Si=3.2–3.35)–zoned epidote (Ps 38–97)–biotite–titanite–two feldspars–quartz assemblages in the more extensive orthogneisses have been previously thought to have formed under low P– T conditions of ca. 400±50°C at 4 kbar. However, certain orthogneiss samples preserve garnets with XCa up to 0.50, rutile inclusions within titanite or epidote and relict phengite inclusions within epidote with Si contents p.f.u. of up to 3.49 — overlapping with the highest values (3.49–3.62) recorded for phengites in samples of undoubted UHP schists. These and other mineral composition features (such as A-site deficiencies in the highest Si phengites, Na in garnets linked to Y+Yb substitution and Al F Ti −1 O −1 substitution in titanites) are taken to be pointers towards the orthogneisses having experienced a similar metamorphic evolution to the associated UHP schists and eclogites. Re-evaluated garnet–phengite and garnet–biotite Fe/Mg exchange thermometry and calculated 5 rutile+3 grossular+2SiO 2+H 2O=5 titanite+2 zoisite equilibria indicate that the orthogneisses may indeed have followed a common subduction-related clockwise P– T path with the UHP paragneisses and eclogites through conditions of Pmax at ca. 690°C–715°C and 36 kbar to Tmax at ca. 710°C–755°C and 18 kbar, prior to extensive re-crystallisation and re-equilibration of these ductile orthogneisses at ca. 400°C–450°C and 6 kbar. The consequential conclusion, that it is no longer necessary to resort to models of tectonic juxtapositioning to explain the spatial association of these Dabieshan orthogneisses with undoubted UHP lithologies, has far-reaching implications for the interpretation of controversial gneiss–eclogite relationships in other UHP metamorphic terrains. 相似文献
5.
Three types of fluid inclusions have been identified in olivine porphyroclasts in the spinel harzburgite and lherzolite xenoliths from Tenerife: pure CO 2 (Type A); carbonate-rich CO 2–SO 2 mixtures (Type B); and polyphase inclusions dominated by silicate glass±fluid±sp±silicate±sulfide±carbonate (Type C). Type A inclusions commonly exhibit a “coating” (a few microns thick) consisting of an aggregate of a platy, hydrous Mg–Fe–Si phase, most likely talc, together with very small amounts of halite, dolomite and other phases. Larger crystals (e.g. (Na,K)Cl, dolomite, spinel, sulfide and phlogopite) may be found on either side of the “coating”, towards the wall of the host mineral or towards the inclusion center. These different fluids were formed through the immiscible separations and fluid–wall-rock reactions from a common, volatile-rich, siliceous, alkaline carbonatite melt infiltrating the upper mantle beneath the Tenerife. First, the original siliceous carbonatite melt is separated from a mixed CO 2–H 2O–NaCl fluid and a silicate/silicocarbonatite melt (preserved in Type A inclusions). The reaction of the carbonaceous silicate melt with the wall-rock minerals gave rise to large poikilitic orthopyroxene and clinopyroxene grains, and smaller neoblasts. During the metasomatic processes, the consumption of the silicate part of the melt produced carbonate-enriched Type B CO 2–SO 2 fluids which were trapped in exsolved orthopyroxene porphyroclasts. At the later stages, the interstitial silicate/silicocarbonatite fluids were trapped as Type C inclusions. At a temperature above 650 °C, the mixed CO 2–H 2O–NaCl fluid inside the Type A inclusions were separated into CO 2-rich fluid and H 2O–NaCl brine. At T<650 °C, the residual silicate melt reacted with the host olivine, forming a reaction rim or “coating” along the inclusion walls consisting of talc (or possibly serpentine) together with minute crystals of NaCl, KCl, carbonates and sulfides, leaving a residual CO 2 fluid. The homogenization temperatures of +2 to +25 °C obtained from the Type A CO 2 inclusions reflect the densities of the residual CO 2 after its reactions with the olivine host, and are unrelated to the initial fluid density or the external pressure at the time of trapping. The latter are restricted by the estimated crystallization temperatures of 1000–1200 °C, and the spinel lherzolite phase assemblage of the xenolith, which is 0.7–1.7 GPa. 相似文献
6.
We present the results of a thrust fault reactivation study that has been carried out using analogue (sandbox) and numerical modelling techniques. The basement of the Pannonian basin is built up of Cretaceous nappe piles. Reactivation of these compressional structures and connected weakness zones is one of the prime agents governing Miocene formation and Quaternary deformation of the basin system. However, reactivation on thrust fault planes (average dip of ca. 30°) in normal or transtensional stress regimes is a problematic process in terms of rock mechanics. The aim of the investigation was to analyse how the different stress regimes (extension or strike-slip), and the geometrical as well as the mechanical parameters (dip and strike of the faults, frictional coefficients) effect the reactivation potential of pre-existing faults. Results of analogue modelling predict that thrust fault reactivation under pure extension is possible for fault dip angle larger than 45° with normal friction value (sand on sand) of the fault plane. By making the fault plane weaker, reactivation is possible down to 35° dip angle. These values are confirmed by the results of numerical modelling. Reactivation in transtensional manner can occur in a broad range of fault dip angle (from 35° to 20°) and strike angle (from 30° to 5° with respect to the direction of compression) when keeping the maximum horizontal stress magnitude approximately three times bigger than the vertical or the minimum horizontal stress values. Our research focussed on two selected study areas in the Pannonian basin system: the Danube basin and the Derecske trough in its western and eastern part, respectively. Their Miocene tectonic evolution and their fault reactivation pattern show considerable differences. The dominance of pure extension in the Danube basin vs. strike-slip faulting (transtension) in the Derecske trough is interpreted as a consequence of their different geodynamic position in the evolving Pannonian basin system. In addition, orientation of the pre-existing thrust fault systems with respect to the Early to Middle Miocene paleostress fields had a major influence on reactivation kinematics. As part of the collapsing east Alpine orogen, the area of the Danube basin was characterised by elevated topography and increased crustal thickness during the onset of rifting in the Pannonian basin. Consequently, an excess of gravitational potential energy resulted in extension (σv > σH) during Early Miocene basin formation. By the time topography and related crustal thickness variation relaxed (Middle Miocene), the stress field had rotated and the minimum horizontal stress axes (σh) became perpendicular to the main strike of the thrusts. The high topography and the rotation of σh could induce nearly pure extension (dip-slip faulting) along the pre-existing low-angle thrusts. On the contrary, the Derecske trough was situated near the Carpathian subduction belt, with lower crustal thickness and no pronounced topography. This resulted in much lower σv value than in the Danube basin. Moreover, the proximity of the retreating subduction slab provided low values of σh and the oblique orientation of the paleostress fields with respect to the master faults of the trough. This led to the dominance of strike-slip faulting in combination with extension and basin subsidence (transtension). 相似文献
7.
Experimental studies of synthetic and natural basalt systems suggest that conditions of magma genesis and fractionation depend fundamentally on mantle temperatures and lithospheric stress fields. In general, compressional settings are more conducive to polybaric fractionation than extensional settings and in this regard, the Anatolian magmatic province offers a natural laboratory for comparing near-coeval basalt eruptions as a function of regional tectonics — compressional (collision-related) régimes dominating in eastern Anatolia and extensional tectonics characterizing a western province related to Aegean Sea opening. Projection of Plio-Quaternary basalt normative compositions from the Western Anatolia Extensional Province (WAEP), the Central Anatolian ‘Ova’ Province (CAOP), and Eastern Anatolia Compressional Province (EACP) are projected onto Ol–Ne–Cpx and Pl–Cpx–Ol planes in the simplified basalt system (Ne–Cpx–Ol–Qz), each showing distinctive liquid lines of descent. WAEP basalts are mostly constrained by low-pressure (< 0.5 GPa) cotectics while CAOP and EACP compositions conform to moderate and/or high-pressure (0.8–3.0 GPa) cotectics. Overall, a quasi-linear shift from moderate and/or high-pressure to low-pressure equilibria matches the westward transgression from compressional east Anatolia to the extensional west Anatolian–Aegean region. Comparison of their respective primary (mantle-equilibrated) magmas–simulated by normalizing their compositions to MgO = 15 wt.% (Mg-15)–with parameterized anhydrous and H 2O-undersaturated experimental melts suggests they segregated from spinel- to garnet-lherzolite mantle facies at pressures between c. 2 and 3 GPa (c. 70–100 km depth) under H 2O-undersaturated conditions. Interpolated potential temperatures ( Tp) and lithospheric stretching factors ( β) range as follows: (1) eastern Anatolian basalts associated with the Arabian foreland show Tp varying between 1250 and 1400 °C (except for the Karacalidag alkali basalts, south of the Bitlis–Zagros fracture zone, for which Tp ranges up to 1450 °C), for β values of 1.2–1.8. Tp values for central Anatolia (e.g. Sivas) range between 1300 and 1375 °C (except for Karapinar, Egrikuyu and Hasandag, which show < 1150 °C), and β values of 1.3–1.4. For western Anatolian basalts, Tp range mostly between 1250 and 1330 °C, except for a single value for Canakkale of 1400 °C and Kula sample showing Tp < 1200 °C, and β values of 1.3–2.0. Variation of these conditions is as great or greater than that between provinces, although there are clearly significant constraints on the inferred polybaric to low-pressure isobaric fractionation régimes. Covariation of total FeO, TiO 2, La/Yb, Ce/Sm, Zr/Y and Zr/Nb reflects small but significant differences in bulk composition and ambient melt fraction while the covariance of Ce/Sm and Sm/Yb is consistent with the segregation of primitive melts at the spinel- to garnet-lherzolite transition. 相似文献
8.
The process of shape-transformation of quartz inclusions from polyhedral to spherical grains in albite single crystals during metamorphism is mainly controlled by the grain boundary diffusion of oxygen along the quartz/albite interface to reduce the interfacial free energy. The rate of the process, which is represented by the growth rate of the curvature of the edge surface of the grain, depends significantly on temperature and on the grain size of the quartz inclusion. The relations between temperature, T, the time, tr, and the critical radius, Rc, which is equal to the radius of maximum spherical grains, are given by log Rc = −0.11 Eb/ RT + 0.25log tr + C, in which Eb is the activation energy of the grain boundary diffusion of oxygen along the quartz/albite interface and C is a material constant. The mean critical radius of spherical quartz inclusions in albite is 5 μm for the upper chlorite zone and garnet zone, 10 μm for the lower biotite zone, and 20 μm for the upper biotite zone in the Sambagawa metamorphic terrain. The mean values of the critical radii of spherical quartz inclusions in oligoclase of the Ryoke metamorphic rocks is about 5 μm for the chlorite zone and about 10–20 μm for the sillimanite zone. Assuming temperatures of about 350°C for the upper chlorite and garnet zones, 400°C for the lower biotite zone, 550°C for the upper biotite zone, and 700°C for the sillimanite zone, the activation energy for the grain boundary diffusion of oxygen along the quartz/plagioclase interfase is estimated to be about 30 kcal/mol. 相似文献
9.
During the last decade, it has been shown that accurate analyses of calcite twinning in thin section may allow computation of the paleo-deviatoric stress tensor associated with this deformation. Following from the work of Larroque and Laurent (1988), and Lacombe et al. (1989), this is a new application of the Etchecopar inverse method. Weakly deformed limestones from about 150 to 200 km north of the Pyrenean chain (South France) were studied. The Etchecopar inverse method, which can be used on a microcomputer, is comparable to the method of analysis of striated fault planes proposed by Etchecopar et al. in 1981, as it determines the principal stress orientations and the stress ellipsoid shape ratio φ = (σ 2 − σ 3)/(σ 1 − σ 3). The Etchecopar method using calcite twins has been selected for this study because it is suitable for the determination of polyphase deformation in coarse-grained limestones (Lacombe et al. 1989). Ten samples of oolitic limestones, cemented with sparry calcite, from the Bajocian (170 Ma) and the Oligocene (30 Ma) were studied. For each of them, only one or two stress tensors were determined: the first is characterized by a principal compressive stress axis σ1 which is horizontal and approximately N-S. Local departures from this orientation have been observed and are interpreted as local stress perturbations. For the second, which was defined in the Oligocene, but occurred only locally in the Jurassic limestones, the position of σ1 is nearly vertical; the direction of extension σ3 is either NE-SW or undefined into the horizontal plane (σ2 = σ3); this radial extension is interpreted as the result of two or more superposed extensive deformation phases with vertical σ1. The N-S compression was never found in the Oligocene limestones, and from its orientation, it is assumed to correspond to the Pyrenean deformation. These results are compared to the more complex deformation pattern obtained from classical microtectonical studies (Arthaud and Choukroune, 1972; Bonijoly and Blès, 1983; Granier and Blès, 1988; Blès et al., 1989). Only the major tectonic events are recorded by calcite twinning. Finally, the suitability of calcite twin analyses for the determination of complex polyphase deformation is discussed. 相似文献
10.
Coexisting melt (MI), fluid-melt (FMI) and fluid (FI) inclusions in quartz from the Oktaybrskaya pegmatite, central Transbaikalia, have been studied and the thermodynamic modeling of PVTX-properties of aqueous orthoboric-acid fluids has been carried out to define the conditions of pocket formation. At room temperature, FMI in early pocket quartz and in quartz from the coarse-grained quartz–oligoclase host pegmatite contain crystalline aggregates and an orthoboric-acid fluid. The portion of FMI in inclusion assemblages decreases and the volume of fluid in inclusions increases from the early to the late growth zones in the pocket quartz. No FMI have been found in the late growth zones. Significant variations of solid/fluid ratios in the neighboring FMI result from heterogeneous entrapment of coexisting melts and fluids by a host mineral. Raman spectroscopy, SEM EDS and EMPA indicate that the crystalline aggregates in FMI are dominated by mica minerals of the boron-rich muscovite–nanpingite CsAl 2[AlSi 3O 10](OH,F) 2 series as well as lepidolite. Topaz, quartz, potassium feldspar and several unidentified minerals occur in much lower amounts. Fluid isolations in FMI and FI have similar total salinity (4–8 wt.% NaCl eq.) and H 3BO 3 contents (12–16 wt.%). The melt inclusions in host-pegmatite quartz homogenize at 570–600 °C. The silicate crystalline aggregates in large inclusions in pocket quartz completely melt at 615 °C. However, even after those inclusions were significantly overheated at 650±10 °C and 2.5 kbar during 24 h they remained non-homogeneous and displayed two types: (i) glass+unmelted crystals and (ii) fluid+glass. The FMI glasses contain 1.94–2.73 wt.% F, 2.51 wt.% B 2O 3, 3.64–5.20 wt.% Cs 2O, 0.54 wt.% Li 2O, 0.57 wt.% Ta 2O 5, 0.10 wt.% Nb 2O 5, 0.12 wt.% BeO. The H 2O content of the glass could exceed 12 wt.%. Such compositions suggest that the residual melts of the latest magmatic stage were strongly enriched in H 2O, B, F, Cs and contained elevated concentrations of Li, Be, Ta, and Nb. FMI microthermometry showed that those melts could have crystallized at 615–550 °C. Crystallization of quartz–feldspar pegmatite matrix leads to the formation of H2O-, B- and F-enriched residual melts and associated fluids (prototypes of pockets). Fluids of different compositions and residual melts of different liquidus–solidus P–T-conditions would form pockets with various internal fluid pressures. During crystallization, those melts release more aqueous fluids resulting in a further increase of the fluid pressure in pockets. A significant overpressure and a possible pressure gradient between the neighboring pockets would induce fracturing of pockets and “fluid explosions”. The fracturing commonly results in the crushing of pocket walls, formation of new fractures connecting adjacent pockets, heterogenization and mixing of pocket fluids. Such newly formed fluids would interact with a primary pegmatite matrix along the fractures and cause autometasomatic alteration, recrystallization, leaching and formation of “primary–secondary” pockets. 相似文献
11.
A detailed fluid inclusion study has been carried out on the hydrocarbon-bearing fluids found in the peralkaline complex, Lovozero. Petrographic, microthermometric, laser Raman and bulk gas data are presented and discussed in context with previously published data from Lovozero and similar hydrocarbon-bearing alkaline complexes in order to further understand the processes which have generated these hydrocarbons. CH 4-dominated inclusions have been identified in all Lovozero samples. They occur predominantly as secondary inclusions trapped along cleavage planes and healed fractures together with rare H 2O-dominant inclusions. They are consistently observed in close association with either arfvedsonite crystals, partially replaced by aegirine, aegirine crystals or areas of zeolitization. The majority of inclusions consist of a low-density fluid with CH 4 homogenisation temperatures between −25 and −120 °C. Those in near-surface hand specimens contain CH 4+H 2 (up to 40 mol%)±higher hydrocarbons. However, inclusions in borehole samples contain CH 4+higher hydrocarbons±H 2 indicating that, at depth, higher hydrocarbons are more likely to form. Estimated entrapment temperatures and pressures for these inclusions are 350 °C and 0.2–0.7 kbar. A population of high-density, liquid, CH 4-dominant inclusions have also been recorded, mainly in the borehole samples, homogenising between −78 and −99 °C. These consist of pure CH 4, trapped between 1.2 and 2.1 kbar and may represent an early CH 4-bearing fluid overprinted by the low-density population. The microthermometric and laser Raman data are in agreement with bulk gas data, which have recorded significant concentrations of H 2 and higher hydrocarbons up to C 6H 12 in these samples. These data, combined with published isotopic data for the gases CH 4, C 2H 6, H 2, He and Ar indicate that these hydrocarbons have an abiogenic, crustal origin and were generated during postmagmatic, low temperature, alteration reactions of the mineral assemblage. This would suggest that these data favour a model for formation of hydrocarbons through Fischer–Tropsch type reactions involving an early CO 2-rich fluid and H 2 derived from alteration reactions. This is in contrast to the late-magmatic model suggested for the formation of hydrocarbons in the similar peralkaline intrusion, Ilímaussaq, at temperatures between 400 and 500 °C. 相似文献
12.
Minor granulites (believed to be pre-Triassic), surrounded by abundant amphibolite-facies orthogneiss, occur in the same region as the well-documented Triassic high- and ultrahigh-pressure (HP and UHP) eclogites in the Dabie–Sulu terranes, eastern China. Moreover, some eclogites and garnet clinopyroxenites have been metamorphosed at granulite- to amphibolite-facies conditions during exhumation. Granulitized HP eclogites/garnet clinopyroxenites at Huangweihe and Baizhangyan record estimated eclogite-facies metamorphic conditions of 775–805 °C and ≥15 kbar, followed by granulite- to amphibolite-facies overprint of ca. 750–800 °C and 6–11 kbar. The presence of (Na, Ca, Ba, Sr)-feldspars in garnet and omphacite corresponds to amphibolite-facies conditions. Metamorphic mineral assemblages and P– T estimates for felsic granulite at Huangtuling and mafic granulite at Huilanshan indicate peak conditions of 850 °C and 12 kbar for the granulite-facies metamorphism and 700 °C and 6 kbar for amphibolite-facies retrograde metamorphism. Cordierite–orthopyroxene and ferropargasite–plagioclase coronas and symplectites around garnet record a strong, rapid decompression, possibly contemporaneous with the uplift of neighbouring HP/UHP eclogites. Carbonic fluid (CO2-rich) inclusions are predominant in both HP granulites and granulitized HP/UHP eclogites/garnet clinopyroxenites. They have low densities, having been reset during decompression. Minor amounts of CH4 and/or N2 as well as carbonate are present. In the granulitized HP/UHP eclogites/garnet clinopyroxenites, early fluids are high-salinity brines with minor N2, whereas low-salinity fluids formed during retrogression. Syn-granulite-facies carbonic fluid inclusions occur either in quartz rods in clinopyroxene (granulitized HP garnet clinopyxeronite) or in quartz blebs in garnet and quartz matrices (UHP eclogite). For HP granulites, a limited number of primary CO2 and mixed H2O–CO2(liquid) inclusions have also been observed in undeformed quartz inclusions within garnet, orthopyroxene, and plagioclase which contain abundant, low-density CO2±carbonate inclusions. It is suggested that the primary fluid in the HP granulites was high-density CO2, mixed with a significant quantity of water. The water was consumed by retrograde metamorphic mineral reactions and may also have been responsible for metasomatic reactions (“giant myrmekites”) occurring at quartz–feldspar boundaries. Compared with the UHP eclogites in this region, the granulites were exhumed in the presence of massive, externally derived carbonic fluids and subsequently limited low-salinity aqueous fluids, probably derived from the surrounding gneisses. 相似文献
13.
High-calcium, nepheline-normative ankaramitic basalts (MgO > 10 wt.%, CaO/Al 2O 3 > 1) from Rinjani volcano, Lombok (Sunda arc, Indonesia) contain phenocrysts of clinopyroxene and olivine (Fo 85–92) with inclusions of spinel (Cr# 58–77) and crystallised melt. Olivine crystals have variable but on average low NiO (0.10–0.23 wt.%) and high CaO (0.22–0.35 wt.%) contents for their forsterite number. The CaO content of Fo 89–91 olivine is negatively correlated with the Al 2O 3 content of enclosed spinel (9–15 wt.%) and positively correlated with the CaO/Al 2O 3 ratios of melt inclusions (0.9–1.5). Major and trace element patterns of melt inclusions are similar to that of the host rock, indicating that the magma could have formed by accumulation of small batches of melt, with compositions similar to the melt inclusions. The liquidus temperature of the magma was 1275 °C, and its oxygen fugacity ≤ FMQ + 2.5. Correlations between K 2O, Zr, Th and LREE in the melt inclusions are interpreted to reflect variable degrees of melting of the source; correlations between Al 2O 3, Na 2O, Y and HREE are influenced by variations in the mineralogy of the source. The melts probably formed from a water-poor, clinopyroxene-rich mantle source. 相似文献
14.
A brief review of the geology of the tar sand areas of Nigeria is given. Analysis shows that the tar sand used for the tests consists of a well graded silty sand (cmf) with about 5% clay; and 3–5% bitumen. Results presented show a very high in situ compressive strength of about 450 kN/m 2, a high ratio of tensile to compressive strength of about 22%, peak shear strength parameters of Cp′=15kN/m 2and φp′ = 19° and residual parameters of Cr =0, φr = 18°. The compacted tar sand behaved like an overconsolidated soil with a preconsolidating pressure, Pc of 140 kN/m2. In general, the results of the in situ strength tests indicate that the Nigerian tar sand behaved as a soft sandstone. 相似文献
15.
Liquid inclusions in quartz found in rocks of amphibolite and of granulite facies were studied. In the former water is predominant, in the latter CO 2 (probably juvenile). Estimates of PT conditions during metamorphism based on the study of inclusions gave values (800°C, 8 kb) comparable to those obtained by the petrological study (7–800 °C, 6–8 kb) presented in part I. 相似文献
16.
The Ditrău Alkaline Massif is an intrusion into the Bucovina nappe system that is part of the Mesozoic crystalline zone located in Transylvania, Romania, in the Eastern Carpathians. Nepheline syenites are the most abundant rocks in the central and eastern part of the Massif, and represent the last major intrusion of the complex. Fluid inclusions in nepheline, aegirine and albite were trapped at magmatic conditions on or below the H 2O-saturated nepheline syenite solidus at about 400–600 °C and 2.5–5 kbars. Early nepheline, and to a lesser extent albite, were altered by highly saline fluids to produce cancrinite, sodalite and analcime, during this process cancrinite also trapped fluid inclusions. The fluids, in most cases, can be modeled by the H 2O–NaCl system with varying salinity; however inclusions with more complex fluid composition (containing K, Ca, CO 3, etc., in addition to NaCl) are common. Raman spectroscopic analyses of daughter minerals confirm the presence of alkali-carbonate fluids in some of the earliest inclusions in nepheline, aegirine and albite. During crystallization, the melts exsolved a high salinity, carbonate-rich magmatic fluid that evolved to lower salinity as crystallization progressed. Phases that occur early in the paragenesis contain high-salinity inclusions while late phases contain low-salinity inclusions. The salinity trend is consistent with experimental data for the partitioning of chlorine between silicic melt and exsolved aqueous fluid at about 2.0 kbars. The activity of water (aH2O) in the melt increases during crystallization, resulting in the formation of hydrous phases during late-stage crystallization of the nepheline syenites. 相似文献
17.
The Berriedale Limestone formed at about 80°S paleolatitude and contains many glacial dropstones. It formed during a period of major Gondwana deglaciation. The Berriedale Limestone contains mostly bryozoans, brachiopods and bivalves, with some intraclasts and rare pellets. The faunal diversity is low and the fauna are similar to the modern cold-water foramol faunal assemblage. Micrite, microspar and spar occur as equant to well developed rhombs of calcite. The coarse spar cements are bored and are ruptured by dropstones, indicating submarine origin of low-Mg calcite at water-temperatures of around 3°C. The mixing zone cementation was preceded by erosion of early formed crystals. The eroded crystals occur as inclusions in mixing zone cements. The fauna are characterized by heavy δ13C and light δ18O. The whole-rock field of δ18O-δ13C falls at the edge of “Normal Marine Limestone” and deviates to lighter δ18O values (down to −16.7‰ PDB). Lightest δ18O values ( −22‰ PDB) of fresh-water sparry calcite cement are similar to those in the Early Permian continental tillites, suggesting that the Permian sea was diluted by isotopically light melt waters. Micrite δ18O values (−9.2 to −12.6‰ PDB) are within the range of whole-rock values. The δ18O values of calcite in shales are lighter than limestone values. The δ18O values of the fauna give an unrealistic range of sea-water temperatures because the fauna have equilibrated with variable amounts of melt waters. However, calculated original δ18O values of the fauna indicate temperatures < 4°C. The heaviest δ18O of fauna gives cold temperatures of 9°C (with δw −2.8‰) and −3°C (with δw −6‰). The lightest values of sparry calcite cements (−22‰ PDB) indicate that the limestone reacted with cold melt waters. The δ18O of Permian sea is estimated to be about +1.2‰ and was diluted by melt waters as light as −27‰ SMOW. 相似文献
18.
Coarse-grained whiteschist, containing the assemblage: garnet+kyanite+phengite+talc+quartz/coesite, is an abundant constituent of the ultrahigh-pressure metamorphic (UHPM) belt in the Kulet region of the Kokchetav massif of Kazakhstan. Garnet displays prograde compositional zonation, with decreasing spessartine and increasing pyrope components, from core to rim. Cores were recrystallized at T=380°C (inner) to 580°C (outer) at P<10 kbar (garnet–ilmenite geothermometry, margarite+quartz stability), and mantles at T=720–760°C and PH20=34–36 kbar (coesite+graphite stability, phengite geobarometer, KFMASH system reaction equilibria). Textural evidence indicates that rims grew during decompression and cooling, within the Qtz-stability field. Silica inclusions (quartz and/or coesite) of various textural types within garnets display a systematic zonal distribution. Cores contain abundant inclusions of euhedral quartz (type 1 inclusions). Inner mantle regions contain inclusions of polycrystalline quartz pseudomorphs after coesite (type 2), with minute dusty micro-inclusions of chlorite, and more rarely, talc and kyanite in their cores; intense radial and concentric fractures are well developed in the garnet. Intermediate mantle regions contain bimineralic inclusions with coesite cores and palisade quartz rims (type 3), which are also surrounded by radial fractures. Subhedral inclusions of pure coesite without quartz overgrowths or radial fractures (type 4) occur in the outer part of the mantle. Garnet rims are silica-inclusion-free. Type 1 inclusions in garnet cores represent the low-P, low-T precursor stage to UHPM recrystallization, and attest to the persistence of low-P assemblages in the coesite-stability field. Coesites in inclusion types 2, 3, and 4 are interpreted to have sequentially crystallized by net transfer reaction (kyanite+talc=garnet+coesite+H2O), and were sequestered within the garnet with progressively decreasing amounts of intragranular aqueous fluid. During the retrograde evolution of the rock, all three inclusion types diverged from the host garnet P–T path at the coesite–quartz equilibrium, and followed a trajectory parallel to the equilibrium boundary resulting in inclusion overpressure. Coesite in type 2 inclusions suffered rapid intragranular H2O-catalysed transformation to quartz, and ruptured the host garnet at about 600°C (when inclusion P27 kbar, garnet host P9 kbar). Instantaneous decompression to the host garnet P–T path, passed through the kyanite+talc=chlorite+quartz reaction equilibrium, resulting in the dusty micro-assemblage in inclusion cores. Type 3 inclusions suffered a lower volumetric proportion transformation to quartz at the coesite–quartz equilibrium, and finally underwent rupture and decompression when T<400°C, facilitating coesite preservation. Type 4 coesite inclusions are interpreted to have suffered minimal transformation to quartz and proceeded to surface temperature conditions along or near the coesite–quartz equilibrium boundary. 相似文献
19.
Syntectonic eclogites, associated with blueschist parageneses, have recrystallized in metabasalts from eastern Corsica under very low temperatures (420°C). The evolution of these eclogites is recorded by the order of development of metamorphic minerals, as demonstrated by helicitic inclusions of lawsonite and actinolite in Fe-rich garnets, and the occurrence of fibrous Na-pyroxenes in the pressure shadows and cracks of boudinaged garnets, within a foliated matrix composed of glaucophane, Ca---Fe garnets and lawsonite. A Schreinemakers analysis has been completed on the lawsonite-ferroglaucophane-actinolite-almandine-grossular-ferro-omphacite-chlorite system in a (T,P,μH2O)-space. The resulting three-dimensional relationships are applied to the studied samples. They are consistent with a prograde increase in temperature at low μH2O, producing eclogites from blueschists, and with a subsequent retrogressive decrease in pressure. 相似文献
20.
Metamorphic conditions within arenaceous, calcareous and argillaceous supracrustal rocks of the Magondi Mobile Belt (Zimbabwe) range from greenschist to granulite facies. Within the high-grade segment, basement gneisses of early Proterozoic age and argillaceous rocks of the Mid-Proterozoic Piriwiri Group are intruded by charnockites and enderbites. Metamorphic mineral assemblages and thermobarometric data for enderbitic granulites of Nyaodza show temperatures of 700–800°C and pressures of 5–7 kbar for the peak of granulite-facies metamorphism. Microthermometry and Raman microspectroscopy reveal that CO 2, associated with minor N 2, has been the dominant fluid phase during granulite-facies metamorphism. The chronology of the CO 2 inclusions and the development of microtextures and mineral assemblages in the enderbites indicates that isolated negative crystal shaped CO 2 inclusions in quartz and plagioclase porphyroclasts entrap syn-metamorphic fluids of medium-high densities (0.88–0.90 g/cm 3). Lower density (0.71–0.77 g/cm 3) CO 2 inclusions in trails and clusters within the same minerals were formed from local re-equilibration and re-entrapment of the former (near-) peak granulitic CO 2 inclusions. As in many other granulites, syn-metamorphic CO 2 is associated with intrusives emplaced near the peak of metamorphism. 相似文献
|
