首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
针对GNSS三维无约束平差不依赖基准且拥有高精度几何网形的特点,以GNSS监测网作为一个整体的时空观测单元,由GNSS网测站间相互关联的所有基线长度和基线夹角变化综合衡量网形的变化,用网形的变化集中反映区域地壳形变信息。利用地壳形变高空间相关性的特点,采用主成分时空响应分析的方法实现了区域地壳形变信息的快速提取。通过对2013年芦山Ms7.0地震近场区域陆态网GPS基准站2010—2014年观测数据的解算,提取并分析了对应地震前后近场区域地壳形变时空分布特征及形变的动态演变过程。  相似文献   

2.
杨兵  杨志强  田镇  陈祥 《测绘学报》2022,51(9):1881-1889
针对经验模态分解(empirical mode decomposition,EMD)在GNSS坐标时间序列的降噪过程中存在筛选准则的选取和模态混叠效应等问题,本文引入Hausdorff距离(Hausdorff distance,HD)筛选准则并结合小波分解(wavelet decomposition,WD),提出EMD-HD&WD算法。通过对我国大陆构造环境监测网络149个GNSS测站的垂向坐标时间序列降噪处理,分别利用复合指标T值、测站的速度不确定度和闪烁噪声振幅验证算法的可靠性和普适性。结果显示:HD优于现有的筛选准则;EMD-HD&WD算法对测站的速度不确定度和闪烁噪声振幅的平均改正率均为88.4%。分析表明,本文算法能够有效识别和剔除噪声并且改善EMD的模态混叠效应,提高GNSS垂向坐标时间序列的模型精度。  相似文献   

3.
获取准确的GNSS测站速度对于研究全球板块运动、地壳形变、地震活动及其地球动力学过程至关重要。为此,以GNSS基线解算后的基线向量作为观测值,重建了最小二乘综合速度解算模型和卡尔曼滤波速度估计模型。模型中,考虑了测站坐标、运动速度、年、半年周期项一同作为参数,在基线解网平差的同时,一并求解获取速度估值。同时,利用坐标时序分析的方法,顾及白噪声和幂律噪声的影响,对单日解坐标时间序列重建了时序速度拟合估计模型,以获取长期趋势项作为速度值。基于3种模型,对川滇地区中国地壳运动观测网络2010—2014年21个GPS基准站的观测数据进行了速度估计与对比分析。结果表明:3种模型所估计测站速度非常接近,差异基本处于0~1mm/a范围之内;速度估值中误差均在亚毫米水平。由此得出,3种速度估计模型具有本质的一致性,均可正确估计测站运动速度,能够满足高精度地壳形变研究的需要。  相似文献   

4.
党亚民  杨强  王伟  梁玉可 《测绘学报》2022,51(7):1192-1205
2020珠峰高程测量,获得了丰富的青藏高原及邻区的GNSS监测数据。本文收集了陆态网、尼泊尔CORS网GNSS长期观测数据,计算了该地区20多年GNSS三维速度场,利用GRACE模型精化了垂直速度场,通过活动块体模型,从地壳运动、块体运动与应变、块体相对运动等多个方面研究了青藏高原地壳运动与构造形变特征。研究表明,青藏高原地壳形变具有明显的分区特征,南北向收缩主要表现在拉萨块体,东西向伸展主要表现在巴颜喀拉块体,中部羌塘块体没有明显水平挤压,但地壳隆升速率最大,且水平面积有扩大趋势,本文研究能够在一定程度上支持青藏高原地壳增厚学说。  相似文献   

5.
随着北斗三号完成全球组网以及硬件技术发展,地壳形变监测网络的全球导航卫星系统(global navigation satellite system, GNSS)接收机正朝着多系统、超高频(≥50 Hz)更新升级。基于陆态网络和中国青海省连续运行参考站的GNSS观测数据,获取2021年青海玛多Mw 7.4地震的同震位移波,并进行了震前精度统计和功率谱密度分析。结果表明,北斗三号在本次地震中的位移拾取精度比全球定位系统(global positioning system,GPS)更优;采样率提高到50 Hz对削弱位移时间序列混叠效应作用不显著,在10 Hz左右达到饱和;对50 Hz同震位移波差分获取到的速度和加速度序列噪声较大,难以利用。综合应用场景和成本考虑,GNSS地震监测的采样率最高设置在5~10 Hz即可。  相似文献   

6.
水准和全球导航卫星系统(global navigation satellite system, GNSS)成果是研究中国大陆垂直运动的重要数据,充分发挥水准点高精度和GNSS点分布均匀的优势,有利于提升垂直运动模型的可靠性。在融合过程中,针对水准和GNSS成果缺少重合点导致速度融合失效的问题,提出一种基于模型结果融合的方法,分别利用水准和GNSS成果建立垂直运动模型,并基于模型格网点精度及控制点与模型格网点的最近距离联合确定两类模型点权值,逐点加权平均,实现两类模型的融合;针对利用反距离加权方法建模过程中观测点速度精度和空间距离均影响定权结果的问题,提出了权因子相乘的方法,合理确定各因素影响程度。综合利用国家一等水准网、国家GNSS大地控制网等成果,基于双因子相乘的方式定权建立单源垂直运动模型,并按照基于结果融合的方法建立了中国大陆垂直运动模型。结果表明,华北、苏沪一带沉降严重,极个别区域沉降速度达100 mm/a;东北、西藏一带呈现隆升趋势,局部隆升速度达5 mm/a;其余地区垂直运动相对稳定。  相似文献   

7.
在高精度大地测量观测数据处理和相关地球物理解释中,大气负荷由于影响较大,需要考虑。利用全球大气模型和区域气象站气压数据,采用移去恢复方法和球谐分析方法,计算了三峡地区大气负荷对地壳形变和重力变化的影响。提供了一种利用局部气压数据改善该区域大气负荷影响变化计算效果的合理算法,提高局部气压数据和全球模型数据利用的合理性和准确性。研究发现,大气负荷对垂直形变的影响在空间分布上中长波占优,在三峡地区的年变化幅度大于20 mm,对地面重力变化影响的年变化幅度一般不超过10 μGal,对水平形变影响较小。  相似文献   

8.
2015年尼泊尔地震对珠穆朗玛峰高程的影响,近年一直受到全世界关注.2020年珠穆朗玛峰高程测量在珠穆朗玛峰及周边地区布设了高精度的全球导航卫星系统(global navigation satellite system,GNSS)形变监测网,收集了1999-2020年跨喜马拉雅山脉的32个连续运行参考站(continu...  相似文献   

9.
大规模GNSS基准站网快速同步处理方法研究   总被引:3,自引:0,他引:3  
目前我国GNSS连续运行基准站网已基本建设完毕,全国范围内建设完成约2000个GNSS连续运行基准站。随着站点规模的加大,数据计算的效率也迫切需要提高,采用传统的高精度数据处理软件已适应不了大规模GNSS网的数据解算要求。本文基于BERNESE5.2软件研究了我国“陆态网络工程”260个基准站的大规模GNSS网同步数据处理方法,通过修改源程序及利用并行计算技术,成功实现了陆态网络基准站快速、高效、高精度的数据计算能力。实例验证表明,陆态网络单天260个站的数据在无需分区的情况下,可在1 h内获得全球框架下的约束解,解算的框架点坐标精度在毫米量级,大大提高了国家数据中心的大规模GNSS网数据处理能力。  相似文献   

10.
为了研究近年来我国GNSS基准站地壳大气负荷垂向形变细部特征,使用格林函数积分及简化方法对中国大陆构造环境监测网络中的6个基准站共计36个月的大气负荷效应进行了计算和分析,结果表明,大气负荷是造成地壳非构造垂向形变的重要因素,大气负荷效应引起的地壳垂向形变量的区域性差异及垂向形变量在我国东北部和西部新疆地区为最大,大气负荷效应改正可使GPS垂向精度进一步提高。   相似文献   

11.
应用GPS定位技术进行城市或区域地壳变形监测,研究了GPS监测的数据处理和精度分析的理论和方法.使用高精度的定位分析软件GAMIT,对某城市地壳变形监测网的试验观测数据进行数据处理,并对解算得到的基线向量和坐标分别进行精度分析,结果表明:在100km范围内,GPS基线重复率在平面上比例误差可以达到10-8,垂直方向比例误差可以达到10-7;GPS监测点的三维坐标重复率精度可达到3mm左右,能满足城市或区域地壳变形监测的精度要求.  相似文献   

12.
GNSS coordinate time series data for permanent reference stations often suffer from random, or even continuous, missing data. Missing data interpolation is necessary due to the fact that some data processing methods require evenly spaced data. Traditional missing data interpolation methods usually use single point time series, without considering spatial correlations between points. We present a MATLAB software for dynamic spatiotemporal interpolation of GNSS missing data based on the Kriged Kalman Filter model. With the graphical user interface, users can load source GNSS data, set parameters, view the interpolated series and save the final results. The SCIGN GPS data indicate that the software is an effective tool for GNSS coordinate time series missing data interpolation.  相似文献   

13.
A grid-based tropospheric product for China using a GNSS network   总被引:1,自引:0,他引:1  
Tropospheric delay accounts for one source of error in global navigation satellite systems (GNSS). To better characterize the tropospheric delays in the temporal and spatial domain and facilitate the safety-critical use of GNSS across China, a method is proposed to generate a grid-based tropospheric product (GTP) using the GNSS network with an empirical tropospheric model, known as IGGtrop. The prototype system generates the GTPs in post-processing and real-time modes and is based on the undifferenced and uncombined precise point positioning (UU-PPP) technique. GTPs are constructed for a grid form (\(2.0{^{\circ }}\times 2.5{^{\circ }}\) latitude–longitude) over China with a time resolution of 5 min. The real-time GTP messages are encoded in a self-defined RTCM3 format and broadcast to users using NTRIP (networked transport of RTCM via internet protocol), which enables efficient and safe transmission to real-time users. Our approach for GTP generation consists of three sequential steps. In the first step, GNSS-derived zenith tropospheric delays (ZTDs) for a network of GNSS stations are estimated using UU-PPP. In the second step, vertical adjustments for the GNSS-derived ZTDs are applied to address the height differences between the GNSS stations and grid points. The ZTD height corrections are provided by the IGGtrop model. Finally, an inverse distance weighting method is used to interpolate the GNSS-derived ZTDs from the surrounding GNSS stations to the location of the grid point. A total of 210 global positioning system (GPS) stations from the crustal movement observation network of China are used to generate the GTPs in both post-processing and real-time modes. The accuracies of the GTPs are assessed against with ERA-Interim-derived ZTDs and the GPS-derived ZTDs at 12 test GPS stations, respectively. The results show that the post-processing and real-time GTPs can provide the ZTDs with accuracies of 1.4 and 1.8 cm, respectively. We also apply the GTPs in real-time kinematic GPS PPP, and the results show that the convergence time of the PPP solutions is shortened. These results confirm that the GTPs can act as an efficient information source to augment GNSS positioning over China.  相似文献   

14.
大气加权平均温度(Tm)是全球导航卫星系统(global navigation satellite system, GNSS)反演大气水汽(precipitation water vapor, PWV)的关键参数。当前已有Tm模型提供的Tm信息难以捕获其日周期变化,因此限制了其在高时间分辨率GNSS PWV估计中的精度。大气再分析资料可提供高时空分辨率的Tm格点产品,但是在使用时需要对其进行空间插值,且Tm在高程上的变化远大于其在水平方向上变化。同时,针对中国区域地形起伏大等特点,提出顾及垂直递减率的中国区域Tm格点产品空间插值方法,以分布于中国区域的2015年89个探空站资料为参考值,验证了提出的方法在全球大地测量观测系统大气中心Tm格点产品和美国国家航空和太空管理局提供的MERRA-2的Tm格点产品中的空间插值精度。结果表明:(1)在顾及垂直递减率的Tm格点产品空间插值中,反距离加权法的...  相似文献   

15.
We have used up to 12 years of data to assess DORIS performance for geodynamics applications. We first examine the noise characteristics of the DORIS time-series of weekly station coordinates to derive realistic estimates of velocity uncertainties. We find that a combination of white and flicker noise best explains the DORIS time-series noise characteristics. Second, weekly solutions produced by the Institut Géographique National/Jet Propulsion Laboratory (IGN/JPL) DORIS Analysis Centre are combined to derive a global velocity field. This solution is combined with two independent GPS solutions, including 11 sites on Nubia and 5 on the Somalia plate. The combination indicates that DORIS horizontal velocities have an average accuracy of 3 mm/year, with best-determined sites having velocity accuracy better than 1 mm/year (one-sigma levels). Using our combined velocity field, we derive an updated plate kinematics model with a focus on the Nubia–Somalia area. Including DORIS data improves the precision of the angular velocity vector for Nubia by 15%. Our proposed model provides robust bounds on the maximum opening rates along the East African Rift (4.7–6.7 mm/year). It indicates opening rates 15 and 7% slower than values predicted by NUVEL-1A for the southern Atlantic Ocean and Indian Ocean, respectively. These differences are likely to arise from the fact that NUVEL-1A considered Africa as a single non-deforming plate, while here we use a more refined approach.  相似文献   

16.
彭葳  戴吾蛟 《测绘工程》2016,25(4):60-65
连续的全球卫星导航系统(GNSS)基准站的坐标时间序列中包含了复杂的噪声信号、非构造形变及其它因素的影响,尤其在垂直方向,对GNSS基准站在国际地球参考框架(ITRF)下的运动速率估计产生了较大的干扰。为进一步提高速率精度,文中采用整体模态分解(EEMD)方法对GNSS基准站的垂向观测时间序列进行分解,并根据各种信号的Hurst值进行分类及重构为噪声信号、季节性信号和长期趋势信号,采用最小二乘方法拟合长期趋势信号得到垂向速率。通过对中国大陆构造环境监测网络(CMONOC)的GNSS台站从2001—2013年近13a的垂向坐标时间序列的实例分析,采用基于EEMD和Husrt指数的最小二乘法能够准确地估计GNSS基准站的垂向速率。  相似文献   

17.
This paper uses multiquadric equations interpolation to establish a widely covered and valuable speed field model of China, with which the horizontal crustal movement patterns are obtained. The present-day vertical crustal movement velocity image of China is also expressed by GPS observations, from which we can know the vertical crustal movement patterns.  相似文献   

18.
This paper uses multiquadric equations interpolation to establish a widely covered and valuable speed field model of China, with which the horizontal crustal movement patterns are obtained. The present-day vertical crustal movement velocity image of China is also expressed by GPS observation, from which we can know the vertical crustal movement patterns.  相似文献   

19.
一种GNSS网络RTK改进的综合误差内插方法   总被引:2,自引:1,他引:2  
在全球导航卫星系统(GNSS)网络RTK综合误差内插法(CBI)的基础上,提出了一种改进的综合误差内插方法(MCBI)。该方法把综合误差分为对流层模型改正、一阶电离层影响和除一阶电离层影响外的其他综合影响3个部分。实例证明了该方法不仅在精度上比综舍误差内插法要高,而且更利于流动站的应用。  相似文献   

20.
利用国家重大科学工程中国地壳运动观测网络的两期GPS观测值得到川滇区域内测站的速度。以这些速度为约束,基于数值流形模型拟合了川滇地区的速度场。它很好地结合了块体内部的连续变形和块体间的非连续变形。较非连续变形分析模型,地质构造速度模型和配置拟合模型等更真实模拟了地壳运动速度场,为相关地学研究提供了很好的基础。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号