共查询到20条相似文献，搜索用时 31 毫秒
1.
We propose a dye tracer method to characterize fluid and solute fluxes across the sediment-water interface. Zones of groundwater discharge within the streambed are first identified, and small volume slugs of 0.5 to 1 mL fluorescein dye are released at known subsurface depths. Fluorescein dye allows for visual identification of interface breakthrough locations and times, and dye concentrations at the point of discharge are recorded over time by a fluorometer to generate high resolution breakthrough curves. Groundwater velocities and dispersivities at the demonstration site are estimated by numerically fitting dye breakthroughs to the classical advection-dispersion equation, although the methodology is not limited to a specific transport model. Breakthroughs across the stream-sediment interface at the demonstration site are nonlinear with tracer release depth, and velocity estimates from breakthrough analysis are significantly more reliable than visual dye (time to first dye expression) and Darcy methods which tend to overestimate and underestimate groundwater velocity, respectively. The use of permanent injection points within the streambed and demonstrated reproducibility of dye breakthroughs allow for study of fluid and solute fluxes under seasonally varying hydrologic conditions. The proposed approach also provides a framework for field study of nonconservative, reactive solutes and allows for the determination of characteristic residence times at various depths in the streambed to better understand chemical and nutrient transformations. 相似文献
2.
An approximate analytical solution to the advection-dispersion equation was derived to describe solute transport during spherical-flow conditions in single-well push-pull tests. The spherical-flow case may be applicable to aquifer tests conducted in packed intervals or partially penetrating wells. Using results of two-dimensional numerical simulations, we briefly illustrate the applicability of the derived spherical-flow solution and provide a comparison with its cylindrical-flow counterpart. Good agreement between simulated extraction-phase breakthrough curves and the spherical-flow solution was found when the length of the injection/extraction region was small compared to both aquifer thickness and maximum solute frontal position at the end of the injection phase. On the other hand, discrepancies between simulated breakthrough curves and the spherical-flow solution increased with increasing anisotropy in hydraulic conductivities. Several inherent limitations embedded in its derivation such as assumptions of isotropy and homogeneity warrant the cautious use of the spherical-flow solution. 相似文献
3.
This pore-scale modeling study in saturated porous media shows that compound-specific effects are important not only at steady-state and for the lateral displacement of solutes with different diffusivities but also for transient transport and solute breakthrough. We performed flow and transport simulations in two-dimensional pore-scale domains with different arrangement of the solid grains leading to distinct characteristics of flow variability and connectivity, representing mildly and highly heterogeneous porous media, respectively. The results obtained for a range of average velocities representative of groundwater flow (0.1–10 m/day), show significant effects of aqueous diffusion on solute breakthrough curves. However, the magnitude of such effects can be masked by the flux-averaging approach used to measure solute breakthrough and can hinder the correct interpretation of the true dilution of different solutes. We propose, as a metric of mixing, a transient flux-related dilution index that allows quantifying the evolution of solute dilution at a given position along the main flow direction. For the different solute transport scenarios we obtained dilution breakthrough curves that complement and add important information to traditional solute breakthrough curves. Such dilution breakthrough curves allow capturing the compound-specific mixing of the different solutes and provide useful insights on the interplay between advective and diffusive processes, mass transfer limitations, and incomplete mixing in the heterogeneous pore-scale domains. The quantification of dilution for conservative solutes is in good agreement with the outcomes of mixing-controlled reactive transport simulations, in which the mass and concentration breakthrough curves of the product of an instantaneous transformation of two initially segregated reactants were used as measures of reactive mixing. 相似文献
4.
A pilot-scale nutrient injection will (NIW) (4 m by 4 m by 1 m) was installed in the Borden Aquifer lo serve as a pulsed injection source of a potassium acetate solution for the stimulation of anaerobic microbial activity. The success of the flushing procedure was evaluated by monitoring the breakthrough of the acetate solution at several multilevel piezometers installed in the wall. Although some variation in the ground water velocity was observed with depth, the wall was flushed with reasonable uniformity after about six hours of injection and withdrawal, representing about one pore volume, Calculations bused on head level data collected during the flush, and on the solute breakthrough curves, indicated that about 90% of the flow induced by the pumping and injecting was confined to the permeable wall. These results show that a permeable wall injection system is a viable method of introducing solutes uniformly to a cross section of aquifer, with minimal perturbation of the natural flow system. In addition lo its importance for the biostimulation system tested in this project the flushing of permeable walls may have applications in other semi-passive remedial systems, such as the rejuvenation of reactive barriers. 相似文献
5.
A method to estimate reactive transport parameters as well as geometric conduit parameters from a multitracer test in a karst aquifer is provided. For this purpose, a calibration strategy was developed applying the two-region nonequilibrium model CXTFIT. The ambiguity of the model calibration was reduced by first calibrating the model with respect to conservative tracer breakthrough and later transferring conservative transport parameters to the reactive model calibration. The reactive transport parameters were only allowed to be within a defined sensible range to get reasonable calibration values. This calibration strategy was applied to breakthrough curves obtained from a large-scale multitracer test, which was performed in a karst aquifer of the Swabian Alb, Germany. The multitracer test was conducted by the simultaneous injection of uranine, sulforhodamine G, and tinopal CBS-X. The model succeeds to represent the tracer breakthrough curves (TBCs) of uranine and sulforhodamine G and verifies that tracer-rock interactions preferably occur in the immobile fluid region, although the fraction of this region amounts to only 3.5% of the total water. However, the model failed to account for the long tailing observed in the TBC of tinopal CBS-X. Sensitivity analyses reveal that model results for the conservative tracer transport are most sensitive to average velocity and volume fraction of the mobile fluid region, while dispersion and mass transfer coefficients are least influential. Consequently, reactive tracer calibration allows the determination of sorption sites in the mobile and immobile fluid region at small retardation coefficients. 相似文献
6.
A 3D ERT study of solute transport in a large experimental tank 总被引：2，自引：0，他引：2
L. Slater A. Binley R. Versteeg G. Cassiani R. Birken S. Sandberg 《Journal of Applied Geophysics》2002,49(4)
A high resolution, cross-borehole, 3D electrical resistivity tomography (ERT) study of solute transport was conducted in a large experimental tank. ERT voxels comprising the time sequence of electrical images were converted into a 3D array of ERT estimated fluid conductivity breakthrough curves and compared with direct measurements of fluid conductivity breakthrough made in wells. The 3D ERT images of solute transport behaviour were also compared with predictions based on a 3D finite-element, coupled flow and transport model, accounting for gravity induced flow caused by concentration differences.The tank (dimensions 185×245×186 cm) was filled with medium sand, with a gravel channel and a fine sand layer installed. This heterogeneous system was designed to complicate solute transport behaviour relative to a homogeneous sand tank, and to thus provide a challenging but insightful analysis of the ability of 3D ERT to resolve transport phenomena. Four ERT arrays and 20 piezometers were installed during filling. A NaCl tracer (conductivity 1.34 S/m) was injected and intensively monitored with 3D ERT and direct sampling of fluid chemistry in piezometers.We converted the bulk conductivity estimate for 250 voxels in the ERT imaged volume into ERT estimated voxel fluid conductivity by assuming that matrix conduction in the tank is negligible. In general, the ERT voxel response is in reasonable agreement with the shape of fluid conductivity breakthrough observed in six wells in which direct measurements of fluid conductivity were made. However, discrepancies occur, particularly at early times, which we attribute to differences between the scale of the image voxels and the fluid conductivity measurement, measurement errors mapped into the electrical inversion and artificial image roughness resulting from the inversion.ERT images revealed the 3D tracer distribution at 15 times after tracer injection. The general pattern and timing of solute breakthrough observed with ERT agreed with that predicted from the flow/transport modelling. However, the ERT images indicate a vertical component of tracer transport and preferential flow paths in the medium sand. We attribute this to transient vertical gradients established during tracer injection, and heterogeneity caused by sorting of the sand resulting from the filling procedure. In this study, ERT provided a unique dataset of 250 voxel breakthrough curves in 1.04 m3. The use of 3D ERT to generate an array of densely sampled estimated fluid conductivity breakthrough curves is a potentially powerful tool for quantifying solute transport processes. 相似文献
7.
Two-well tracer tests are often conducted to investigate subsurface solute transport in the field. Analyzing breakthrough curves in extraction and monitoring wells using numerical methods is nontrivial due to highly nonuniform flow conditions. We extended approximate analytical solutions for the advection-dispersion equation for an injection-extraction well doublet in a homogeneous confined aquifer under steady-state flow conditions for equal injection and extraction rates with no transverse dispersion and negligible ambient flow, and implemented the solutions in Microsoft Excel using Visual Basic for Application (VBA). Functions were implemented to calculate concentrations in extraction and monitoring wells at any location due to a step or pulse injection. Type curves for a step injection were compared with those calculated by numerically integrating the solution for a pulse injection. The results from the two approaches are similar when the dispersivity is small. As the dispersivity increases, the latter was found to be more accurate but requires more computing time. The code was verified by comparing the results with published-type curves and applied to analyze data from the literature. The method can be used as a first approximation for two-well tracer test design and data analysis, and to check accuracy of numerical solutions. The code and example files are publicly available. 相似文献
8.
Random walk approach is used to develop a model for long-term prediction of water quality in shallow marine waters. The model allows one to simulate variations in hydrological situations, reactive solutes, interaction between solutes and liquid and solid boundaries. The model application is illustrated by calculations for Amur Bay. Calculations using the long-term prediction model has not found a stationary state in the pollution level. The velocities of seaward motion of pollution front and the rates of increase in the concentration of a nonreactive solute are given. 相似文献
9.
Comparison of Stainless Steel vs. PTFE Miniwells for Monitoring Halogenated Organic Solute Transport
Gino C. Bianchi-Mosquera Douglas M. Mackay 《Ground Water Monitoring & Remediation》1992,12(4):126-131
Field tests of organic solute transport behavior have often been monitored using small-diameter wells (miniwells). To determine if experimental results could be significantly biased by sorption to, desorption from, or diffusion through sampling lines, dissolved concentrations of tetrachloroethene and carbon tetrachloride were measured in ground water samples collected simultaneously from the same spatial location during a forced-gradient test in the Borden aquifer using polytetrafluoroethene (PTFE) and stainless steel miniwells (1/8-inch O.D.).
A semiautomated organic analytical system was used on-site to obtain real-time results, which avoided sample holding problems and permitted optimizing sampling times. The breakthrough curves (plots of concentration vs. time) for both organic compounds indicate that under the conditions of this experiment (low organic solute concentrations, short exposure time of sampling lines to the plume, adequate flushing of sampling lines) there is no significant difference between concentration histories (breakthrough curves) collected using a polytetrafluoroethene sampling line and those collected using a stainless steel sampling line. This suggests that organic solute tailing seen in this and also in a similar transport experiment previously conducted at the site is the result of transport processes in the aquifer rather than an artifact introduced by the PTFE miniwells. 相似文献
A semiautomated organic analytical system was used on-site to obtain real-time results, which avoided sample holding problems and permitted optimizing sampling times. The breakthrough curves (plots of concentration vs. time) for both organic compounds indicate that under the conditions of this experiment (low organic solute concentrations, short exposure time of sampling lines to the plume, adequate flushing of sampling lines) there is no significant difference between concentration histories (breakthrough curves) collected using a polytetrafluoroethene sampling line and those collected using a stainless steel sampling line. This suggests that organic solute tailing seen in this and also in a similar transport experiment previously conducted at the site is the result of transport processes in the aquifer rather than an artifact introduced by the PTFE miniwells. 相似文献
10.
Characterizing and predicting reactive solute transport in low hydraulic conductivity ( K ) clay-rich media is challenging because the very long transport time for solutes renders conventional column tests impractical. In this study, a centrifugation technique was developed to assess the transport of a simple aqueous solution (NaCl) by accelerating flow by centrifugal force through low K (1.1 × 10−11 m/s) core samples. Duplicate cores (52-mm length × 33-mm diameter) were centrifuged at 330 × g for 90 d to model the migration of saline pore water (0.5 M NaCl) under in situ conditions through an approximately 17-m-thick clay prototype over approximately 24,000 years. A PHREEQC one-dimensional reactive solute transport code simulated effluent breakthrough of the NaCl during centrifugation, with best-fit cation exchange coefficients similar to batch tests. The calibrated code was used to predict solute profile development over the long term in the prototype or simulated field-scale conditions. Chromatographic separation of solutes due to ion exchange was evident over several meters in the simulated prototype and the field profile. The applicability of centrifugation methods to predict transport of more complex suites of reactive solutes over the long term is yet to be verified. 相似文献
11.
Pressure pulsing technology is an innovative method that has been developed with the aim of overcoming preferred flow paths associated with remediation techniques that rely on the injection of reagents. Numerical and field experiments were conducted to assess how pressure pulsing affects groundwater flow and solute transport during reagent injection. A series of field experiments were performed at two field sites where a monitoring network designed to capture the breakthrough of solutes delivered from an injection well was installed. Pressure pulsing and conventional injection methods were used at each site. One site was comprised of fine sand with low heterogeneity, while the other was moderately heterogeneous with discrete layers varying from fine sand to silt. The data suggest that breakthrough was more uniform for the pressure pulsing injections; however, this difference was minor and complicated by sorption of some of the tracers employed. The groundwater flow and solute transport modeling exercise simulated the rapid boundary pressure modulation that occurs in association with pressure pulsing. Two‐dimensional (2D) simulations revealed that repeated sudden onset of injection cessation produces brief periods of gradient reversal and the development of a mixing zone near the injection well. The spatial extents of this mixing zone were found to be highly dependent upon the hydraulic diffusivity of the medium, with medium heterogeneity and pulsing frequency playing secondary roles. Three‐dimensional (3D) numerical simulations were used to benchmark the observations from one of the field sites. The results from the modeling effort showed that solute breakthrough from a pressure pulsing injection is more dispersed relative to a conventional injection as a result of the mixing zone phenomenon; however, we were unable to directly observe this mixing zone using the instrumentation deployed at the two field sites. 相似文献
12.
《Ground Water Monitoring & Remediation》2000,20(4):104-113
A solute breakthrough curve measured during a two-well tracer test was successfully predicted in 1986 using specialized contaminant transport models. Water was injected into a confined, unconsolidated sand aquifer and pumped out 125 feet (38.3 m) away at the same steady rate. The injected water was spiked with bromide for over three days; the outflow concentration was monitored for a month. Based on previous tests, the horizontal hydraulic conductivity of the thick aquifer varied by a factor of seven among 12 layers. Assuming stratified flow with small dispersivities, two research groups accurately predicted breakthrough with three-dimensional (12-layer) models using curvilinear elements following the arc-shaped flowlines in this test.
Can contaminant transport models commonly used in industry, that use rectangular blocks, also reproduce this breakthrough curve? The two-well test was simulated with four MODFLOW-based models, MT3D (FD and HMOC options), MODFLOWT, MOC3D, and MODFLOW-SURFACT.
Using the same 12 layers and small dispersivity used in the successful 1986 simulations, these models fit almost as accurately as the models using curvilinear blocks. Subtle variations in the curves illustrate differences among the codes. Sensitivities of the results to number and size of grid blocks, number of layers, boundary conditions, and values of dispersivity and porosity are briefly presented. The fit between calculated and measured breakthrough curves degenerated as the number of layers and/or grid blocks decreased, reflecting a loss of model predictive power as the level of characterization lessened. Therefore, the breakthrough curve for most field sites can be predicted only qualitatively due to limited characterization of the hydrogeology and contaminant source strength. 相似文献
Can contaminant transport models commonly used in industry, that use rectangular blocks, also reproduce this breakthrough curve? The two-well test was simulated with four MODFLOW-based models, MT3D (FD and HMOC options), MODFLOWT, MOC3D, and MODFLOW-SURFACT.
Using the same 12 layers and small dispersivity used in the successful 1986 simulations, these models fit almost as accurately as the models using curvilinear blocks. Subtle variations in the curves illustrate differences among the codes. Sensitivities of the results to number and size of grid blocks, number of layers, boundary conditions, and values of dispersivity and porosity are briefly presented. The fit between calculated and measured breakthrough curves degenerated as the number of layers and/or grid blocks decreased, reflecting a loss of model predictive power as the level of characterization lessened. Therefore, the breakthrough curve for most field sites can be predicted only qualitatively due to limited characterization of the hydrogeology and contaminant source strength. 相似文献
13.
《Advances in water resources》2005,28(5):479-492
The transient storage model (TSM) has been widely used in studies of stream solute transport and fate, with an increasing emphasis on reactive solute transport. In this study we perform sensitivity analyses of a conservative TSM and two different reactive solute transport models (RSTM), one that includes first-order decay in the stream and the storage zone, and a second that considers sorption of a reactive solute on streambed sediments. Two previously analyzed data sets are examined with a focus on the reliability of these RSTMs in characterizing stream and storage zone solute reactions. Sensitivities of simulations to parameters within and among reaches, parameter coefficients of variation, and correlation coefficients are computed and analyzed. Our results indicate that (1) simulated values have the greatest sensitivity to parameters within the same reach, (2) simulated values are also sensitive to parameters in reaches immediately upstream and downstream (inter-reach sensitivity), (3) simulated values have decreasing sensitivity to parameters in reaches farther downstream, and (4) in-stream reactive solute data provide adequate data to resolve effective storage zone reaction parameters, given the model formulations. Simulations of reactive solutes are shown to be equally sensitive to transport parameters and effective reaction parameters of the model, evidence of the control of physical transport on reactive solute dynamics. Similar to conservative transport analysis, reactive solute simulations appear to be most sensitive to data collected during the rising and falling limb of the concentration breakthrough curve. 相似文献
14.
Relative Recovery of Thermal Energy and Fresh Water in Aquifer Storage and Recovery Systems 总被引：1，自引：0，他引：1 
下载免费PDF全文
下载免费PDF全文 This paper explores the relationship between thermal energy and fresh water recoveries from an aquifer storage recovery (ASR) well in a brackish confined aquifer. It reveals the spatial and temporal distributions of temperature and conservative solutes between injected and recovered water. The evaluation is based on a review of processes affecting heat and solute transport in a homogeneous aquifer. In this simplified analysis, it is assumed that the aquifer is sufficiently anisotropic to inhibit density‐affected flow, flow is axisymmetric, and the analysis is limited to a single ASR cycle. Results show that the radial extent of fresh water at the end of injection is greater than that of the temperature change due to the heating or cooling of the geological matrix as well as the interstitial water. While solutes progress only marginally into low permeability aquitards by diffusion, conduction of heat into aquitards above and below is more substantial. Consequently, the heat recovery is less than the solute recovery when the volume of the recovered water is lower than the injection volume. When the full volume of injected water is recovered the temperature mixing ratio divided by the solute mixing ratio for recovered water ranges from 0.95 to 0.6 for ratios of maximum plume radius to aquifer thickness of 0.6 to 4.6. This work is intended to assist conceptual design for dual use of ASR for conjunctive storage of water and thermal energy to maximize the potential benefits. 相似文献
15.
We study solute transport in a periodic channel with a sinusoidal wavy boundary when inertial flow effects are sufficiently large to be important, but do not give rise to turbulence. This configuration and setup are known to result in large recirculation zones that can act as traps for solutes; these traps can significantly affect dispersion of the solute as it moves through the domain. Previous studies have considered the effect of inertia on asymptotic dispersion in such geometries. Here we develop an effective spatial Markov model that aims to describe transport all the way from preasymptotic to asymptotic times. In particular we demonstrate that correlation effects must be included in such an effective model when Péclet numbers are larger than O(100) in order to reliably predict observed breakthrough curves and the temporal evolution of second centered moments. For smaller Péclet numbers correlation effects, while present, are weak and do not appear to play a significant role. For many systems of practical interest, if Reynolds numbers are large, it may be typical that Péclet numbers are large also given that Schmidt numbers for typical fluids and solutes can vary between 1 and 500. This suggests that when Reynolds numbers are large, any effective theories of transport should incorporate correlation as part of the upscaling procedure, which many conventional approaches currently do not do. We define a novel parameter to quantify the importance of this correlation. Next, using the theory of CTRWs we explain a to date unexplained phenomenon of why dispersion coefficients for a fixed Péclet number increase with increasing Reynolds number, but saturate above a certain value. Finally we also demonstrate that effective preasymptotic models that do not adequately account for velocity correlations will also not predict asymptotic dispersion coefficients correctly. 相似文献
16.
Michael J. Truex Vince R. Vermeul David T. Adamson Mart Oostrom Lirong Zhong Rob D. Mackley Brad G. Fritz Jake A. Horner Tim C. Johnson Jonathan N. Thomle Darrell R. Newcomer Chris D. Johnson Michal Rysz Tom W. Wietsma Charles J. Newell 《Ground Water Monitoring & Remediation》2015,35(3):34-45
Heterogeneity of hydraulic properties in aquifers may lead to contaminants residing in lower‐permeability zones where it is difficult to deliver remediation amendments using conventional injection processes. The focus of this study is to examine use of a shear‐thinning fluid (STF) to improve the uniformity of remedial amendment distribution within a heterogeneous aquifer. Previous studies have demonstrated the significant potential of STFs for improving remedial amendment delivery in heterogeneous aquifers, but quantitative evaluation of these improvements from field applications is lacking. A field‐scale test was conducted that compares data from successive injection of a tracer in water followed by injection of a tracer in an STF to evaluate the impact of the STF on tracer distribution uniformity in the presence of permeability contrasts within the targeted injection zone. Data from tracer breakthrough at multiple depth‐discrete monitoring intervals and electrical resistivity tomography (ERT) showed that inclusion of STF in the injection solution improved the distribution of the injected fluid within the targeted treatment zone. One improvement was a reduction in the movement of injected fluids through high‐permeability pathways, as evidenced by slower breakthrough of tracer at monitoring locations where breakthrough in baseline tracer‐only injection data was faster. In addition, STF‐amended injection solutions arrived faster and to a greater extent in monitoring locations within low‐permeability zones. ERT data showed that the STF injection covered a higher percentage of a two‐dimensional cross section within the injection interval between the injection well and a monitoring well about 3 m away. 相似文献
17.
Two large-scale (9.5 m long, 4.7 m wide, 2.6 m deep), three-dimensional artificial aquifers were constructed to investigate the influence of spatial variations in aquifer properties on contaminant transport. One aquifer was uniformly filled with coarse sand media (0.6 to 2.0 mm) and the other was constructed as a heterogeneous aquifer using blocks of fine, medium, and coarse sands. The key features of these artificial aquifers are described. An innovative deaeration tower was constructed to overcome a problem of the aquifers becoming blocked with excess air from the ground water source. A series of tracer injection experiments were conducted to test the homogeneity of the first aquifer that was purposely built as a homogeneous aquifer and to calculate values of aquifer parameters. Experimental data show that the aquifer is slightly heterogeneous, and hydraulic conductivity values are significantly higher down one side of the aquifer compared to the mean value. There was very good agreement in estimated dispersivity values between the plume area ratio methods and the curve fitting of tracer breakthrough curves. Dispersivity estimates from a full areal source injection (12.2 m2) experiment using a 1D analytical model were higher than estimates from a limited source injection (0.2 m2) experiment using a 3D model, possibly because the 1D model does not take account of the heterogeneity of hydraulic conductivity in the aquifer, thus overestimating dispersivity. Transverse and vertical dispersivity values were about five times less than the longitudinal dispersivity. There was slight sorption of Rhodamine WT onto the aquifer media. 相似文献
18.
Multiple numerical approaches have been developed to simulate porous media fluid flow and solute transport at the pore scale. These include 1) methods that explicitly model the three-dimensional geometry of pore spaces and 2) methods that conceptualize the pore space as a topologically consistent set of stylized pore bodies and pore throats. In previous work we validated a model of the first type, using computational fluid dynamics (CFD) codes employing a standard finite volume method (FVM), against magnetic resonance velocimetry (MRV) measurements of pore-scale velocities. Here we expand that validation to include additional models of the first type based on the lattice Boltzmann method (LBM) and smoothed particle hydrodynamics (SPH), as well as a model of the second type, a pore-network model (PNM). The PNM approach used in the current study was recently improved and demonstrated to accurately simulate solute transport in a two-dimensional experiment. While the PNM approach is computationally much less demanding than direct numerical simulation methods, the effect of conceptualizing complex three-dimensional pore geometries on solute transport in the manner of PNMs has not been fully determined. We apply all four approaches (FVM-based CFD, LBM, SPH and PNM) to simulate pore-scale velocity distributions and (for capable codes) nonreactive solute transport, and intercompare the model results. Comparisons are drawn both in terms of macroscopic variables (e.g., permeability, solute breakthrough curves) and microscopic variables (e.g., local velocities and concentrations). Generally good agreement was achieved among the various approaches, but some differences were observed depending on the model context. The intercomparison work was challenging because of variable capabilities of the codes, and inspired some code enhancements to allow consistent comparison of flow and transport simulations across the full suite of methods. This study provides support for confidence in a variety of pore-scale modeling methods and motivates further development and application of pore-scale simulation methods. 相似文献
19.
Cosler DJ 《Ground water》2004,42(2):203-222
Nonequilibrium concentration type curves are numerically developed and sensitivity analyses are performed to examine the relationships between effluent concentrations in partially penetrating monitoring/extraction wells, the vertical plume shape, and the mass transfer characteristics of the aquifer. The governing two-dimensional, axisymmetric nonequilibrium solute transport equation is solved in three stages using an operator-splitting approach. In the first two stages, the advection and dispersion terms are solved with the Eulerian-Lagrangian method, based on the backward method of characteristics for advection and the standard implicit Galerkin finite element method for dispersion. In the third step, the first-order, immobile-mobile domain mass transfer term is computed analytically for both two-site and lognormally distributed, multirate models. Effluent concentration variations with time and contour plots of the pore water concentration distribution in the aquifer are compared for a wide range of field- and laboratory-measured mass transfer rates, various plume shapes, and relevant physical/chemical parameter values, including pumping rate, vertical anisotropy ratio, retardation factor, and porosity. The simulation results show that rate-limited mass transfer can have a significant impact on sample and aquifer pore water concentrations during three-dimensional transport to a partially penetrating well. An alternative dimensionless form of the nonequilibrium solute transport equation is derived to illustrate the key parameter groupings that quantify rate-limited sorption effects and show the relative importance of individual parameters. A hypothetical field application example demonstrates the fitting of dimensional type curves to discrete-interval sampling data in order to evaluate the mass transfer characteristics of an aquifer and shows how type curve superposition can be used to model complex plume shapes. 相似文献
20.
Naturally occurring radon in ground water can potentially be used as an in situ partitioning tracer to characterize dense nonaqueous phase liquid (DNAPL) saturations. The static method involves comparing radon concentrations in water samples from DNAPL-contaminated and noncontaminated portions of an aquifer, while the push-pull method involves the injection (push) and extraction (pull) of a radon-free test solution from a single well. In the presence of DNAPL, radon concentrations during the pull phase are retarded, with retardation manifested in greater dispersion of radon concentrations relative to a conservative tracer. The utility of these methods was investigated in the laboratory using a physical aquifer model (PAM). Static and push-pull tests were performed before and after contamination of the PAM sediment pack with trichloroethene (TCE), and after alcohol cosolvent flushing and pump-and-treat remediation. Numerical simulations were used to estimate the retardation factor for radon in push-pull tests. Radon partitioning was observed in static and push-pull tests conducted after TCE contamination. Calculated TCE saturations ranged up to 1.4% (static test) and 14.1% (push-pull test). Post-remediation tests showed decreases in TCE saturations. The results show that radon is sensitive to changes in DNAPL saturation in space and time. However, the methods are sensitive to DNAPL saturation heterogeneity, test location, sample size, and test design. The influence of these factors on test results, as well as the apparent overestimation of the retardation factor in push-pull tests, warrant further investigation. 相似文献